Attachment_B_-_Specifications-Drawings.pdf

DESCRIPTION/SPECIFICATIONS

FWS SPECIALIZED SPECIFICATIONS

WEST UNIT WATER DRAIN LINE REPLACEMENT

AT

GARRISON DAM NATIONAL FISH HATCHERY COMPLEX

SPECIFICATION INDEX

DIVISION 31 – EARTHWORK

SECTION 312000 EARTH MOVING

DIVISION 33 – UTILITIES

SECTION 331100 WATER UTILITY PIPING

EARTH MOVING 312000 - 1

SECTION 312000 - EARTH MOVING

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Excavating and backfilling for utility trenches.

1.2 DEFINITIONS

A. Backfill: Soil material used to fill an excavation.

1. Initial Backfill: Backfill placed beside and over pipe in a trench, including haunches to support sides of pipe.

2. Final Backfill: Backfill placed over initial backfill to fill a trench.

B. Bedding Course: Aggregate layer placed over the excavated subgrade in a trench before laying pipe.

C. Borrow Soil: Satisfactory soil imported from off-site for use as fill or backfill.

D. Excavation: Removal of material encountered above subgrade elevations and to lines and dimensions indicated.

E. Fill: Soil materials used to raise existing grades.

F. Structures: Buildings, footings, foundations, retaining walls, slabs, tanks, curbs, mechanical and electrical appurtenances, or other man-made stationary features constructed above or below the ground surface.

G. Utilities: On-site underground pipes, conduits, ducts, and cables, as well as underground services within buildings.

1.3 QUALITY ASSURANCE

A. Pre-excavation Conference: Conduct conference at Garrison Dam National Fish Hatchery.

EARTH MOVING 312000 - 2

PART 2 - PRODUCTS

2.1 SOIL MATERIALS

A. General: Provide borrow soil materials when sufficient satisfactory soil materials are not available from excavations.

B. Subbase Material: Naturally or artificially graded mixture of natural or crushed gravel, crushed stone, and natural or crushed sand; ASTM D 2940; with at least 90 percent passing a 1-1/2-inch sieve and not more than 12 percent passing a No. 200 sieve.

C. Base Course: Naturally or artificially graded mixture of natural or crushed gravel, crushed stone, and natural or crushed sand; ASTM D 2940; with at least 95 percent passing a 1-1/2-inch sieve and not more than 8 percent passing a No. 200 sieve.

D. Engineered Fill: Naturally or artificially graded mixture of natural or crushed gravel, crushed stone, and natural or crushed sand; ASTM D 2940; with at least 90 percent passing a 1-1/2-inch sieve and not more than 12 percent passing a No. 200 sieve.

E. Bedding Course: Naturally or artificially graded mixture of natural or crushed gravel, crushed stone, and natural or crushed sand; ASTM D 2940; with 100 percent passing a 3/4-inch sieve and not more than 5 percent passing a No. 200 sieve.

PART 3 - EXECUTION

3.1 PREPARATION

A. Protect structures, utilities, and other facilities from damage caused by settlement, lateral movement, undermining, washout, and other hazards created by earth moving operations.

B. Protect and maintain erosion and sedimentation controls during earth moving operations.

3.2 EXCAVATION, GENERAL

A. Unclassified Excavation: Excavate to subgrade elevations regardless of the character of surface and subsurface conditions encountered. Unclassified excavated materials may include rock, soil materials, and obstructions. No changes in the Contract Sum or the Contract Time will be authorized for rock excavation or removal of obstructions.

1. If excavated materials intended for fill and backfill include unsatisfactory soil materials and rock, replace with satisfactory soil materials.

3.3 EXCAVATION FOR UTILITY TRENCHES

A. Excavate trenches to indicated gradients, lines, depths, and elevations.

EARTH MOVING 312000 - 3

B. Excavate trenches to uniform widths to provide the following clearance on each side of pipe or conduit. Excavate trench walls vertically from trench bottom to a minimum of 12 inches higher than top of pipe or conduit unless otherwise indicated.

1. Clearance: minimum 12 inches each side of pipe or conduit.

C. Trench Bottoms: Excavate and shape trench bottoms to provide uniform bearing and support of pipes and conduit. Shape subgrade to provide continuous support for bells, joints, and barrels of pipes and for joints, fittings, and bodies of conduits. Remove projecting stones and sharp objects along trench subgrade.

1. Excavate trenches minimum of 6 inches deeper than elevation required in rock or other unyielding bearing material, minimum of 4 inches deeper elsewhere, to allow for bedding course.

3.4 STORAGE OF SOIL MATERIALS

A. Stockpile borrow soil materials and excavated satisfactory soil materials without intermixing.

Place, grade, and shape stockpiles to drain surface water. Cover to prevent windblown dust.

1. Stockpile soil materials away from edge of excavations. Do not store within drip line of remaining trees.

3.5 UTILITY TRENCH BACKFILL

A. Place backfill on subgrades free of mud, frost, snow, or ice.

B. Place and compact bedding course on trench bottoms and where indicated. Shape bedding course to provide continuous support for bells, joints, and barrels of pipes and for joints, fittings, and bodies of conduits.

C. Place and compact initial backfill of subbase material, satisfactory soil, free of particles larger than 1 inch in any dimension, to a height of a minimum of 12 inches over the pipe or conduit.

1. Carefully compact initial backfill under pipe haunches and compact evenly up on both sides and along the full length of piping or conduit to avoid damage or displacement of piping or conduit. Coordinate backfilling with utilities testing.

D. Place and compact final backfill of satisfactory soil to final subgrade elevation.

3.6 COMPACTION OF SOIL BACKFILLS AND FILLS

A. Place backfill and fill soil materials in layers not more than 8 inches in loose depth for material compacted by heavy compaction equipment, and not more than 4 inches in loose depth for material compacted by hand-operated tampers.

B. Compact soil materials to not less than the following percentages of maximum dry unit weight according to ASTM D 698.

EARTH MOVING 312000 - 4

1. For utility trenches, compact each layer of initial and final backfill soil material at 95% of maximum dry density weight.

3.7 PROTECTION

A. Protecting Graded Areas: Protect newly graded areas from traffic, freezing, and erosion. Keep free of trash and debris.

B. Repair and reestablish grades to specified tolerances where completed or partially completed surfaces become eroded, rutted, settled, or where they lose compaction due to subsequent construction operations or weather conditions.

C. Where settling occurs before Project correction period elapses, remove finished surfacing, backfill with additional soil material, compact, and reconstruct surfacing.

1. Restore appearance, quality, and condition of finished surfacing to match adjacent work, and eliminate evidence of restoration to greatest extent possible.

3.8 DISPOSAL OF SURPLUS AND WASTE MATERIALS

A. Remove surplus satisfactory soil and waste materials, including unsatisfactory soil, trash, and debris, and legally dispose of them off Owner's property.

END OF SECTION 312000

WATER UTILITY PIPING 331100 - 1

SECTION 331100 – WATER UTILITY PIPING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. The water drain line shall be constructed in the locations shown on the drawings. Excavation, trenching and backfilling shall be in accordance with Section 312000 Earth Moving.

B. Codes and Standards:

1. Plumbing Code Compliance: Comply with applicable portions of National Standard

Plumbing Code pertaining to selection and installation of potable water system materials and products.

2. Water Purveyor Compliance: Comply with requirements of Purveyor supplying water to project, obtain required permits and inspections.

1.2 DEFINITIONS

A. PVC: Polyvinyl chloride plastic.

B. DI: Ductile Iron pressure pipe.

1.3 PERFORMANCE REQUIREMENTS

A. Pressure Rating: 175-psi static water pressure for all pipes and fittings. Pipe joints shall be watertight.

1.4 SUBMITTALS

A. Product Data: For the following:

1. Valves.

2. Valve boxes and appurtenances.

3. Pipes.

4. Disinfection reports and practices

5. Product Data: Submit manufacturer's technical product data and installation instructions for materials and products.

6. Maintenance Data: Submit maintenance data and parts lists for materials and products.

Include this data, product data, shop drawings, and record drawings in maintenance manual.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Do not store plastic pipe, and fittings in direct sunlight.

B. Protect pipe, pipefittings, and seals from dirt and damage.

WATER UTILITY PIPING 331100 - 2

1.6 PROJECT CONDITIONS

A. Interruption of Water Service: Do not interrupt service to facilities occupied by Owner or others unless permitted under the following conditions and then only after arranging to provide temporary service according to requirements indicated:

1. Notify Owner no fewer than two days in advance of proposed interruption of service.

Coordinate interruptions during weekly meetings and at pre-construction meeting.

2. Do not proceed with interruption of service without Owner's written permission.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection:

1. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work.

2. Gate Valves:

a. American Valve Mfg. Corp.

b. American_Darling Valve; Div. of American Cast Iron Pipe Co.

c. Clow Corp.; Valve Div.

d. Dresser Mfg. Div. of ITT Grinnell Valve Co. Inc.

e. Fairbanks Co.

f. Kennedy Valve; Div. of ITT Grinnell Valve Co., Inc.

g. Stockham Valves & Fittings Inc.

h. United Brass Works Inc.

i. United States Pipe and Foundry Co.

j. Waterous Co.

2.2 PIPING MATERIALS

A. General: Plastic pipe with scratches, gouges, or grooves deeper than 10% of the wall thickness or ultraviolet discoloration shall be rejected.

B. Provide piping materials and factory fabricated piping products of sizes, types, pressure ratings, and capacities indicated. Where not indicated, provide proper selection as determined by Installer to comply with installation requirements. Provide sizes and types matching piping and equipment connections; provide fittings of materials that match pipe materials used in potable water systems. Where more than one type of materials or products are indicated, selection is Installer's option.

C. Piping: Provide pipefittings and accessories of same material and weight/class as pipes, with joining method as indicated.

WATER UTILITY PIPING 331100 - 3

D. Ductile Iron Pipe: Polyethylene wrapped Ductile Iron Class 350, with cement mortar lining complying with AWWA C104.

1. Fitting: Ductile iron AWWA C110; cement lined AWWA C104; and rubber-gasket joints, AWWA C111.

E. PVC Pipe: AWWA C900 Class 200 Pipe for gasketed joints and using ASTM F 477, elastomeric seals.

1. Fittings NPS 4 to NPS 8: PVC pressure fittings complying with AWWA C907, for gasketed joints and using ASTM F 477, elastomeric seals.

2. Fittings NPS 10 and Larger: Ductile-iron, compact fittings complying with AWWA C153, for push-on joints and using AWWA C111, rubber gaskets.

2.3 VALVES and BOXES

A. Gate Valves: UL listed, 175-psi working pressure for 12" and smaller, 150 psi for sizes larger than 12". Threaded, flanged, hub, or other end configurations to suit size of valve and piping connection. Inside screw type for use with indicator post, iron body bronze mounted, non-rising stem, and solid wedge disc.

B. Valve Boxes: All valve boxes shall be cast iron and of the sliding type, sized for use with the appropriate valve. All boxes shall extend from the body of the valve to the finished grade. Valve boxes shall be Tyler 6855 or equal. All valve boxes shall be provide with locking covers.

2.4 ACCESSORIES

A. Anchorages: Provide anchorages for tees, wyes, crosses, plugs, caps, bends, and valves. After installation, apply full coat of asphalt or other acceptable corrosion-retarding material to surfaces of ferrous anchorages.

B. Clamps, Straps, and Washers: Steel, ASTM A 506.

C. Rods: Steel, ASTM A 575.

D. Rod Couplings: Malleable-iron, ASTM A 197.

E. Bolts: Steel, ASTM A 307.

F. Cast-Iron Washers: Gray-iron, ASTM A 126.

G. Thrust Blocks: Concrete, 3,000 psi.

PART 3 - EXECUTION

A. Examination: Examine areas and conditions under which water drain line materials and products are to be installed. Do not proceed with work until unsatisfactory conditions have been corrected in manner acceptable to Installer.

WATER UTILITY PIPING 331100 - 4

3.2 EARTHWORK

A. Excavation trenching, and backfilling are specified in Division 31 Section 312000 Earth Moving.

3.3 INSTALLATION

A. Identification: If PVC pipe is used, install a tracer wire along the top of the pipe, secured with tape, and extending to valves.

B. Pipe and pipe fittings:

1. Pipe: Install in accordance with AWWA C600 "Standard for Installation of Ductile-Iron Water Mains and Their Appurtenances".

3.4 PIPING APPLICATIONS

A. Pipe:

1. Ductile Iron Pipe: Install in accordance with AWWA C600 "standard for installation of ductile-iron water mains and their appurtenances" and in accordance with instructions from water purveyor.

2. PVC Pressure pipe, PVC pressure fittings, gaskets, and gasketed joints.

3.5 PIPING INSTALLATION

A. General Locations and Arrangements: Drawing plans and details indicate general location and arrangement of underground water pipes. Location and arrangement of piping layout take design considerations into account. Install piping as indicated, to extent practical. Where specific installation is not indicated, follow piping manufacturer's written instructions.

B. Install proper size increasers, reducers, and couplings where different sizes or materials of pipes and fittings are connected. Reducing size of piping in direction of flow is prohibited.

C. Install piping according to the following:

1. Install piping with restrained joints at tee fittings and at horizontal and vertical changes in direction. Use corrosion-resistant rods, pipe or fitting manufacturer's proprietary restraint system, or cast-in-place concrete supports or anchors.

2. Install piping with line and grade as indicated or below frost line if not indicated.

3. Install ductile-iron pressure piping according to AWWA C600 or AWWA M41.

D. Install ductile-iron special fittings according to AWWA C600.

E. Install PVC pressure piping according to AWWA M23 or ASTM D 2774 and ASTM F 1668.

3.6 INSTALLATION OF VALVES

A. Install valves with stems pointing up. Provide valve box over underground valves.

WATER UTILITY PIPING 331100 - 5

3.7 PIPE JOINT CONSTRUCTION

A. Basic pipe joint construction is specified in Division 33 Section "Common Work Results for Utilities." Where specific joint construction is not indicated, follow piping manufacturer's written instructions.

B. Join pressure piping according to the following:

1. Join ductile-iron pressure piping according to AWWA C660 or AWWA M41 for push-on joints.

2. Join ductile-iron special fittings according to AWWA C660 or AWWA M41 for push-on joints.

3. Join PVC pressure piping according to AWWA M23 for gasketed joints.

4. Join PVC water-service piping according to ASTM D 2855 for solvent-cemented joints.

C. Join dissimilar pipe materials with pressure type couplings.

3.8 FIELD QUALITY CONTROL

A. Piping Tests: Conduct piping tests before joints are covered. Fill pipeline with water 24_hrs prior to testing, and apply test pressure to stabilize system.

B. Hydrostatic Tests: Test at not less than 200 psi for 2 hour, or at 50 psi above maximum static pressure if it is greater than 150 psi.

1. Test fails if leakage exceeds 2_qts per hour per 100 gaskets or joints irrespective of pipe diameter.

2. Increase pressure in 50-psi increments and inspect each joint between increments. Hold at test pressure for one hour, decrease to 0 psi. Slowly increase again to test pressure and hold for one more hour.

3.9 ADJUSTING AND CLEANING

A. Disinfection of Potable Water System: Flush pipe system with clean potable water until no dirty water appears at point of outlet. Fill system with water-chlorine solution containing at least 50 ppm of chlorine. Valve off system and let stand for 24- hrs minimum. Flush with clean potable water until no chlorine remains in water coming from system.

1. Repeat procedure if contamination is present in bacteriological examination.

B. Disinfection of Water Mains: Flush and disinfect in accordance with AWWA C651 "Standard for Disinfecting Water Mains".

C. Contractor shall submit written verification to Project Manager stating, Disinfection has been completed in strict compliance with specification for this project and with jurisdiction having authority over water system.

WATER UTILITY PIPING 331100 - 6

3.10 CLOSING ABANDONED WATER SYSTEMS

A. Abandoned Piping: Close open ends of abandoned underground piping indicated to remain in place. Include closures strong enough to withstand hydrostatic and earth pressures that may result after ends of abandoned piping have been closed. Use either procedure below:

1. Close open ends of piping with at least 8 inch thick, brick masonry bulkheads.

2. Close open ends of piping with threaded metal caps, plastic plugs, or other acceptable methods suitable for size and type of material being closed. Do not use wood plugs.

B. Backfill to grade according to Section EARTH MOVING.

END OF SECTION 331100

© 2024 Microsoft Corporation © 2024 Maxar ©CNES (2024) Distribution Airbus DS

© 2024 Microsoft Corporation © 2024 TomTom

© 2024 Microsoft Corporation © 2024 Maxar ©CNES (2024) Distribution Airbus DS

AutoCAD SHX Text

FISH AND WILDLIFE SERVICE

AutoCAD SHX Text

UNITED STATES DEPARTMENT OF THE INTERIOR

AutoCAD SHX Text

REGION 6 ENGINEERING - DENVER, COLORADO

AutoCAD SHX Text

DESIGNED:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

DRAWN:

AutoCAD SHX Text

DRAWING NO.

AutoCAD SHX Text

SHEET 1 OF

AutoCAD SHX Text

CHECKED:

AutoCAD SHX Text

VICINITY MAP

AutoCAD SHX Text

NO SCALE

AutoCAD SHX Text

OR

AutoCAD SHX Text

RI

AutoCAD SHX Text

ME

AutoCAD SHX Text

RT

AutoCAD SHX Text

PA

AutoCAD SHX Text

DE

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text

NT

AutoCAD SHX Text

TE

AutoCAD SHX Text

IN

AutoCAD SHX Text E

AutoCAD SHX Text

TH

AutoCAD SHX Text

FISH AND WILDLIFE

AutoCAD SHX Text

SERVICE

AutoCAD SHX Text U.S.

AutoCAD SHX Text

U.S. FISH & WILDLIFE SERVICE

AutoCAD SHX Text

SERVICE

AutoCAD SHX Text

FISH AND WILDLIFE

AutoCAD SHX Text

TH

AutoCAD SHX Text

ME

AutoCAD SHX Text

RT

AutoCAD SHX Text

PA

AutoCAD SHX Text

DE

AutoCAD SHX Text

NT

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text

OR

AutoCAD SHX Text

RI

AutoCAD SHX Text

TE

AutoCAD SHX Text

IN

AutoCAD SHX Text E

AutoCAD SHX Text U.S.

AutoCAD SHX Text

APPROVAL SIGNATURES

AutoCAD SHX Text

ANY PRINT ACCOMPANYING THIS INVITATION TO BID MAY BE A REDUCED

AutoCAD SHX Text

REPRODUCTION OF THE WORKING DRAWINGS. IF LINE BELOW DOES NOT

AutoCAD SHX Text

MEASURE SIX INCHES IN LENGTH, THE INDICATED SCALES ARE TO BE

AutoCAD SHX Text

ADJUSTED ACCORDINGLY.

AutoCAD SHX Text

%%UNOTE TO BIDDERS:%%

AutoCAD SHX Text

REGIONAL ENGINEER

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SAFETY

AutoCAD SHX Text

CULTURAL RESOURCES

AutoCAD SHX Text

DATE

AutoCAD SHX Text

DATE

AutoCAD SHX Text

GARRISON DAM NATIONAL FISH HATCHERY

AutoCAD SHX Text McLean

AutoCAD SHX Text

ND

AutoCAD SHX Text

WEST UNIT POND DRAIN LINE REPLACEMENT

AutoCAD SHX Text

COVER SHEET

AutoCAD SHX Text

LB

AutoCAD SHX Text

LB

AutoCAD SHX Text

ED

AutoCAD SHX Text 6/20/24

AutoCAD SHX Text

AutoCAD SHX Text

GARRISON DAM NATIONAL FISH COMPLEX

AutoCAD SHX Text

WEST UNIT POND DRAIN LINE REPLACEMENT

AutoCAD SHX Text SHEET# SHEET NAME 1 COVER SHEET COVER SHEET 2 NOTES AND SITE LAYOUT NOTES AND SITE LAYOUT

AutoCAD SHX Text

PROJECT LOCATION

AutoCAD SHX Text

PROJECT LOCATION

© 2024 Microsoft Corporation © 2024 TomTom

© 2024 Microsoft Corporation © 2024 Maxar ©CNES (2024) Distribution Airbus DS

REPLACE AND

INSTALL NEW

GATE VALVE

REPLACE DAMAGED

PIPE WITH NEW

SCHEDULE 40 PVC

CONNECTIONS TO

EXISTING FILL AND

DRAIN LINE. DIAMETER

SIZE TO BE

DETERMINED BY

CONTRACTOR

MAIN LINE

FILL LINE

INSTALLATION OF NEW

PIPE WILL REQUIRE

PROTECTIVE SYSTEM TO

BE INSTALLED BY THE

CONTRACTOR

Scale: 1"=100'

OVERALL SITE LAYOUT1

Scale: 1" = 20'

PIPE LAYOUT2

AutoCAD SHX Text

DESIGNED

AutoCAD SHX Text

DRAWN

AutoCAD SHX Text

CHECKED

AutoCAD SHX Text

DATE

AutoCAD SHX Text

DRAWING NO.

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

OF

AutoCAD SHX Text

SUB-SHEET

AutoCAD SHX Text

GARRISON DAM NATIONAL FISH HATCHERY COMPLEX

AutoCAD SHX Text West Unit Drain Line Replacement

AutoCAD SHX Text

LB

AutoCAD SHX Text

ED

AutoCAD SHX Text 11/6/24

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

NOTES AND SITE LAYOUT

AutoCAD SHX Text GENERAL NOTES 1. THE UTILITIES SHOWN IN PLAN ARE INDICATED IN ACCORDANCE WITH AVAILABLE RECORDS THE UTILITIES SHOWN IN PLAN ARE INDICATED IN ACCORDANCE WITH AVAILABLE RECORDS IF AVAILABLE. (ALL UTILITIES MAY NOT BE SHOWN.) THE CONTRACTOR SHALL BE RESPONSIBLE FOR OBTAINING EXACT LOCATIONS AND ELEVATIONS OF ALL UTILITIES FROM THE OWNERS OF RESPECTIVE UTILITIES. ALL UTILITIES SHALL BE NOTIFIED AT LEAST 72 HOURS PRIOR TO EXCAVATION. 2. ALL MINOR OBSTRUCTIONS MAY NOT BE SHOWN ON PLANS. THE CONTRACTOR SHALL ALL MINOR OBSTRUCTIONS MAY NOT BE SHOWN ON PLANS. THE CONTRACTOR SHALL VISIT THE SITE AND DETERMINE THE ACTUAL CONDITIONS WITH REGARD TO THE EXISTENCE OF FENCES, DRIVEWAYS, TREES, SIDEWALKS, CULVERTS, UTILITIES AND OTHER MISCELLANEOUS OBSTACLES THAT MAY INTERFERE WITH CONSTRUCTION PRIOR TO SUBMITTING BIDS. 3. PROTECT OR RESTORE ALL LOT CORNERS. PROTECT OR RESTORE ALL LOT CORNERS. 4. SYMBOLS ON THE DRAWINGS (BECAUSE OF THEIR SIZE) MAY NOT REPRESENT THE EXACT SYMBOLS ON THE DRAWINGS (BECAUSE OF THEIR SIZE) MAY NOT REPRESENT THE EXACT LOCATION OF EITHER PROPOSED OR EXISTING UTILITIES. (EX. GATE VALVES & HYDRANTS) 5. ALL UNITS ARE IN FEET, UNLESS OTHERWISE NOTED. ALL UNITS ARE IN FEET, UNLESS OTHERWISE NOTED. 6. IF INSTALLATION DETAILS AND MANUFACTURER'S INSTALLATION REQUIREMENTS DO NOT IF INSTALLATION DETAILS AND MANUFACTURER'S INSTALLATION REQUIREMENTS DO NOT MATCH, THE PROJECT ENGINEER SHALL BE CONSULTED ON DISCREPANCIES.

AutoCAD SHX Text CONTACTS ENGINEERING: U.S. FISH AND WILDLIFE SERVICE REGIONAL OFFICE 6 CONTACT: LEONARD BROWN, PROJECT ENGINEER TELE: 505-463-8145 STATION: GARRISON DAM NATIONAL FISH HATCHERY COMPLEX U.S. FISH AND WILDLIFE SERVICE PROJECT LEADER: AARON VON ESCHEN TELE: 701-654-7451

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 20'

AutoCAD SHX Text 40'

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 100'

AutoCAD SHX Text 200'

AutoCAD SHX Text CONSTRUCTION NOTES: 1. CONTRACTOR SHALL INSTALL PROTECTIVE SYSTEM IN TRENCH PRIOR TO INSTALLATION CONTRACTOR SHALL INSTALL PROTECTIVE SYSTEM IN TRENCH PRIOR TO INSTALLATION OF NEW PIPE. 2. CONSTRUCTION SHALL OCCUR WHEN ADJACENT PONDS ARE DRAINED. CONTRACTOR TO CONSTRUCTION SHALL OCCUR WHEN ADJACENT PONDS ARE DRAINED. CONTRACTOR TO COORDINATE WITH STATION PROJECT LEADER ON DATES. 3. DEPTH OF EXISTING PIPING IS ESTIMATED TO BE OVER ~13 FT. CONTRACTOR SHALL DEPTH OF EXISTING PIPING IS ESTIMATED TO BE OVER ~13 FT. CONTRACTOR SHALL DETERMINE THE ACTUAL DEPTH OF PIPE TO BE REPLACED. 4. THE EXISTING MATERIAL AND PIPE SIZE TO BE REPLACED IS UNKNOWN. THE THE EXISTING MATERIAL AND PIPE SIZE TO BE REPLACED IS UNKNOWN. THE CONTRACTOR SHALL DETERMINE THE EXISTING PIPE DIAMETER SIZE, LENGTH AND DEPTH TO BE REPLACED. 5. LOCATION OF NEW GATE VALVE SHALL BE APPROVED BY HATCHERY.LOCATION OF NEW GATE VALVE SHALL BE APPROVED BY HATCHERY.