Attachment A - DRAFT SOW - RADCON - N64498-21-RFI-4055.pdf

SOW-PWS Template 05 March 2021 version Page 1

Statement of Work (SOW)

Disassembly, Inspect, Analyze and Test, Decontamination, and Packaging of Components for LM2500 Single Shank Turbine (SST) Gas Generator Assemblies (GGA)

1.0 INTRODUCTION

1.0.1 The Naval Surface Warfare Center Philadelphia Division (NSWCPD) is a Department of

Defense entity responsible for research and development, test and evaluation, engineering and fleet support organization for the United States Navy’s (USN) ships, submarines, military watercraft and unmanned vehicles. This requirement is for NSWCPD Code 424, which is responsible for gas turbines which are used for propulsion and power generation.

1.0.2 This contract is for non-personal services. It does not create employment rights with the U.S.

Government whether actual, inherent, or implied

1.0.3 Government/Contractor Relationship

1.0.3.1 The services to be delivered under this Contract are non-personal services and the parties recognize and agree that no employer-employee relationship exists or will exist under the

Contract between the Government and the Contractor's personnel. Therefore, it is in the best interest of the Government to provide both parties a full understanding of their respective obligations.

1.0.3.2 The Contractor employees shall identify themselves as Contractor personnel by introducing themselves or being introduced as Contractor personnel and displaying distinguishable badges or other visible identification for meetings with Government personnel. In addition, Contractor personnel shall appropriately identify themselves as Contractor employees in telephone conversations and in formal and informal written correspondence.

1.0.3.3 Contractor personnel under this Contract shall not engage in any of the inherently

Governmental functions listed at FAR Subpart 7.5 or DFARS Subpart 207.5.

1.0.4 Employee Relationship:

1.0.4.1 The services to be performed under this Contract do not require the Contractor or its personnel to exercise personal judgment and discretion on behalf of the Government. Rather the

Contractor's personnel will act and exercise personal judgment and discretion on behalf of the

Contractor.

1.0.4.2 Rules, regulations, directives, and requirements that are issued by the USN and

NSWCPD under its responsibility for good order, administration, and security are applicable to all personnel who enter a Government installation or who travel on Government transportation.

This is not to be construed or interpreted to establish any degree of Government control that is inconsistent with a non-personal services contract.

SOW-PWS Template 05 March 2021 version Page 2

1.0.4.3 Inapplicability of Employee Benefits: This Contract does not create an employer-employee relationship. Accordingly, entitlements and benefits applicable to such relationships do not apply.

1.0.4.4 It is the Contractor's, as well as the Government's, responsibility to monitor Contract activities and notify the Contracting Officer if the Contractor believes that the intent of this Section has been or may be violated.

1.0.4.4.1 The Contractor shall notify the Contracting Officer in writing via letter or email within three (3) calendar days from the date of any incident that the Contractor considers to constitute a violation of this Section. The notice should include the date, nature, and circumstances of the conduct; the name, function, and activity of each Government employee or Contractor official or employee involved or knowledgeable about such conduct; identify any documents or substance of any oral communication involved in the conduct; and the Contractor's estimated date when, absent a response, cost, schedule or performance will be impacted.

1.0.4.4.2 The Contracting Officer will, within five (5) calendar days after receipt of notice, respond to the notice in writing. In responding, the Contracting Officer will either:

(i) Confirm the conduct is in violation and when necessary direct the mode of further performance,

(ii) Countermand any communication regarded as a violation,

(iii) Deny that the conduct constitutes a violation and when necessary direct the mode of further performance, or

(iv) In the event the notice is inadequate to make a decision, advise the Contractor what additional information is required, and establish the date by which it should be furnished by the Contractor.

1.1 BACKGROUND

This statement of work is for the teardown, inspection, cleaning, evaluation and packaging of

USN radiologically controlled (RADCON) gas turbine assets. Due to operation in radiologically contaminated areas, specialized depot overhaul induction procedures are necessary to process potentially radiological contaminated LM2500 Marine Gas Turbine (MGT) Single Shank

Turbine (SST) Gas Generator assembly (GGA). Processing and handling of these assets requires additional licenses and special handling instructions as well as segregation of material and supporting equipment and a segregated teardown and inspection facility capable of processing potentially contaminated parts. Parts verified clear of contamination following inspections are then reintroduced into an authorized depot overhaul location. Parts verified contaminated shall continue to be handled in accordance with the contractor’s radiological controls procedures.

1.2 SCOPE OF WORK

The contractor shall provide engineering and technical services necessary to receive incoming

RADCON LM2500 SST GGAs in sealed shipping containers, open, inspect and disassemble the engine, survey and document the condition of all LM2500 SST GGA MGT components

SOW-PWS Template 05 March 2021 version Page 3 indicating their level of radiological contamination. Additionally, the contractor shall disposition parts according to their level of radiological contamination as either above or below the permissible limits as defined in the American National Standard Institute Standard (ANSI)

13.12 and Nuclear Regulatory Commission (NRC) Regulatory Guide 1.86 (less than 1000 dpm / 100 cm2 loose / removable contaminants and less than 6000 dpm / 100 cm2 total).

Parts that are identified above the acceptable limits should be cleaned per acceptable facility cleaning procedures with levels being recorded and tracked at every step.

The contractor shall possess, or guarantee possession within 60 days of contract award, all required state licenses or NRC licenses with their respective state to handle and clean radiologically contaminated hardware of the type identified in this contract. The contractor shall have ninety (90) days from contract award to induct the subject RADCON gas turbine asset. The contractor shall furnish a copy of their NRC/State license to the USN prior to beginning deliveries of USN RADCON assets. The contractor shall notify the USN if any changes that are made to the license and shall furnish a copy of the updated license prior to delivery of any USN

RADCON asset.

The contractor must have or be able to procure/construct or be in position of the requisite area, special tooling, and infrastructure necessary to receive, fully disassembly, survey, and package the LM2500 SST GGA and all sub-assemblies and components resultant from disassembly. All facilities and support equipment shall be located within the continental United States. All handling of radiologically contaminated hardware shall take place at the contractor’s facility, in a separate and controlled environment (subsequently referred to as the control area) in order to prevent the potential transfer of radiological contaminants to other areas.

The contractor shall receive RADCON LM2500 SST GGAs in sealed shipping containers from the USN. All material within the container shall be considered under radiological controls. Any

RADCON engine(s) shall be stored in a separate area from any other engines in accordance with the contractor’s RADCON program. Opening of the containers and all subsequent work shall be performed within the control area.

The contractor shall be responsible for disposal of any radiologically contaminated byproducts resultant from executing this Statement of Work. The contractor shall collect all contaminated

USN parts, after cleaning attempts have failed, and store in a container suitable for shipment in accordance with applicable state regulations.

The contractor shall perform the incoming inspection, engine disassembly, survey, cleaning, evaluation and packaging of all LM2500 SST GGAs in accordance with the requirements section of this Statement of Work.

2.0 APPLICABLE DOCUMENTS

2.1 Chapters 4.4 through Chapters 6.26 and Chapter 7.0 of Technical Manual S9234-AB-

MMD-020

SOW-PWS Template 05 March 2021 version Page 4

2.2 General Gas Turbine Bulletin (GGTB) Nr. 23, Revision 4; Procedures for Marine Gas

Turbine Replacement Authorization and Shipment, dated 19 June 2011

Government will provide these docs during solicitation. Documents shall be provided to contractors that are confirmed as bona fide US Department of Defense (DOD) contractors familiar with the procedures to handle technical data package materials that may include limited distribution information.

2.3 ANSI 13.12 - Surface and Volume Radioactivity Standards for Clearance

2.4 NRC Regulator Guide 1.86 – Termination of Operating Licenses for Nuclear Reactors

Contractor can find this info at https://www.nrc.gov/docs/ML0037/ML003740243.pdf

The Contractor shall reference and utilize the latest version available when performing tasks within this SOW.

3.0. REQUIREMENTS

The contractor shall have ninety (90) days from contract award to acquire all tooling and/or equipment required to perform the tasks set forth in this Statement of Work (SOW). All tooling shall be considered under radiological controls once introduced into the control area. At a minimum the following special tools and/or equipment are required to disassemble the LM2500

SST GGA.

A list of special tools and/or equipment required to disassemble the LM2500 Gas Generator

Assembly can be found in chapter 2 of the Industrial Repair Manual for General Electric LM2500

Series Gas Generators and Gas Turbines GEK 99418 for Marine and Industrial Gas Turbines.

These tools are referenced below in table 1.

Tooling Nomenclature P/N

CRF ST AND EARS 1C5615-ST AND 1C5711 1C5615

TMF ST AND EARS 1C5617 W/ST AND 1C5711 1C5617

TMF ST AND EARS 1C5617 W/ST AND 1C5712 1C5711

CRF ST AND EARS 1C5615-ST AND 1C5711 1C5711

STAND EARS 1C6854-STAND 1C5711 1C5711

DSY TABLETOP HOLDER 1C5867

IGB TOOL SET 1C5868

FIXTURE 1C5874

SLING RMV 2ND ST G NOZ ASY 1C5964

CASE HANDLING SLING 1C5976

AFT GG LIFT FXTR PULLER 1C5992

PULLER-RMV 2ND STG SHRDS 1C6771

FRONT GG LIFT FXTR 1C6803

JACKSCREW SET 1C6804

SOW-PWS Template 05 March 2021 version Page 5

TGB STAND 1C6841

TOOLSET TGB HORZ 1C6842

TMF LIFT FIXTURE 1C6847G02

VERTICAL MAINT. STAND AND PILOT 1C6853

STAND EARS 1C6854-STAND 1C5711 1C6854

LIFT FXTR TGB HORZ 1C6855

LIFT FXTR TGB HORZ 1C6872

SLING RMV TGB 1C6874

FIXTURE & TORQUE TUBES (WRENCHES) 1C6897

CASE TABLE FIXTURES-RMV 1C6902

HYDRAULIC REMOVAL OF PINS 1C6942G07

COUPLING NUT TOOLING SET 1C6950

RMV#5 NUT & OIL TUBE UNTORQUE 1C6952

WRENCH SPANNER-OIL TUBE HPT ROTOR 1C6952

OIL TUBE PULLER 1C6953

TOOL-HUB TIE INSTALLATION 1C8134

#3 NUT RTNR RMVTOOL 2C6001

#3 NUT RTNR RMVTOOL 2C6001

#3 INR RACE PULLER 2C6003

#3 INR RACE PULLER 2C6003

PULLER-REAR ROTATING AIR/OIL SL 2C6009

REAR LIFTING EYE 2C6023G02

REAR LIFTING EYE 2C6023G02

TRANSPORT TRUCK 2C6024

TRANSPORT TRUCK 2C6024

DSY FXTR 2C6029

AIRDUCT WRENCH 2C6030

SPOOLS LIFT FXTR 2C6031

FXTR SUPPORT-STGS 1-2 HPC DISKS 2C6037

TOOL SET 2C6042-RMV OUTER #4 BB RACE 2C6042

PULLER-FWD AIR & OIL SEALS 2C6044

PULLER-#4 RB PULLER 2C6045

PULLER-BB RACES, RB RACES, FWD OIL SL 2C6047

SPNR WR-RMV #4 NUT 2C6047

PULLER-SPLIT NUT COLLAR, REAR AIR/SL 2C6048

PULLER ADPTER-ROTATING AIR SEALS 2C6049

TOOL SET-UNTORQUE SPLIT NUT 2C6050

VERTICAL HPT STAND 2C6061

WRENCH SPANNER-PRESSURE TUBE HPT 2C6092

#3 BRG PULLER 2C6139

LIFT EYE AFT 2C6141

GUIDE 2C6187

VANE HOLDEING FIXTURES SET 2C6171

SOW-PWS Template 05 March 2021 version Page 6

WRENCH -NUT SEAL 2C6173

#6 BRG PULLER 2C6183

CRADLE FOR ANTI TORQUE WRENCH TUBE 2C6187

WRENCH-PRESSURE TUBE HPT 2C6189

PULLER FWD & AFT ROTATING SEALS 2C6190

WRENCH, NUT-HPT ROTOR 2C6192

FXTR, LIFT-HPT ROTOR SHAFT & DISK 2C6195

LIFT EYE-HPT FWD 2C6197

LINER DSY TOOLING FOR WELD SHOP 2C6201G03

COMB/LNR PULLER 2C6203

SCREW RODS-RMV SPLIT NUT 2C6206

TRUCK, TRANSPORT 2C6264

REMOVAL HYD RAM 2C6299

REMOVAL HYD RAM 2C6299

#4 BB INST L/RMV TOOL 2C6356G02

HOLDING FXTR-HPC 2C6549

DAMPER SL V PULLER 2C6563

FXTR INST L/RMV-C/R FWD SPLINE ADPTR 2C6588

TOOL, TWISTING-C/R BLD RTNRS STG 2 2C6598

TOOL, TWISTING-C/R BLD RTNR STG 1 2C6601

TOOL UNBEND-C/R BLD RTNR STG 2 2C6604

TOOL SET, HOLDING-HPC ROTOR BOLTS 2C6620

PULLER-RMV AIR TUBES 2C6623

FXTR, LIFT-SLING & HOIST STG1&2 HPT 2C6678

TOOLS, RMV-HPC STG 2 BLD RTNR 2C6968

ARBOR PRESS PEMA 026819

HYDRAULIC SETUP FOR BLACK MULTIPLIER AH2043 AHX-T550 010

HYDRAULIC PUMP AH-P39

LARGE BLACK HYD WRENCH AHX1550

DOCK SIDE DOLLY E91993 PEMA 017258

4EA HEAVY CABLES E96648-4400-60 PEMA 018071

TORQUE MULTIPLIER 10-1 N/A

TORQUE MULTIPLIER 10-1 N/A

SUPPORT LADDER FOR VERTICAL ENGINE N/A

HYDRAULIC ENGINE STSAND FOR DSY N/A

LARGE WRENCH N/A

ACETYLENE TANK AND KIT/REGULATOR N/A

Table 1: List of Gas Generator Assembly (GGA) Tooling for Disassembly and Inspection

The following defines the minimum disassembly, inspection, cleaning and surveying effort of

USN LM2500 SST GGA MGTs. The contractor shall complete a full teardown, inspection and survey of all MGT components to the lowest depot-repairable/replaceable level as defined in

SOW-PWS Template 05 March 2021 version Page 7 applicable documents 2.1 through 2.3 of the Statement of Work. The entire gas generator must be disassembled. A report of all contractor progress, status and management milestones for each

SST GGA shall be provided IAW CDRL A001 on a monthly basis from time of contract award until the asset is returned to the USN. At a minimum the report must include the requirements of this section of the SOW.

3.1. RADCON Procedures:

3.1.1. Pre-disassembly Inspection

3.1.1.1 Visually inspect the contents of each LM2500 container and match all items to the

General Gas Turbine Bulletin 23 (GGTB23) checklist in accordance with paragraph 2.4 of the

Statement of Work. Report any missing items to the contract technical POC.

3.1.1.2 Conduct a radiological inspection of the interior of the engine shipping container and the engine exterior to quantify radiological contamination levels in accordance with paragraph 2.3 and 2.4 of the Statement of Work. Document the survey results for the shipping container and all engine exterior areas. Document the background readings of radiological contamination.

Contractor shall report findings in accordance with CDRL A002.

3.1.2 Disassembly Inspection

3.1.2.1 Completely disassembly the engine in accordance with the Statement of Work. Reference chapters 4.4 through chapters 6.26 of the technical manual S9234-AB-MMD-020 for disassembly instructions.

3.1.2.2 Verify all engine internal components are present. Report any missing items by part number and quantity to the USN.

NOTE: Parts criteria inspections and disposition condition evaluation will be conducted at the

Depot following the final release of parts from RADCON, parts criteria inspections and disposition condition evaluation is not part of this SOW.

3.1.2.3 Conduct a radiological inspection of all engine components from paragraph 3.1.2.1 in accordance with paragraph 2.3 and 2.4 of the Statement of Work. At a minimum LM2500

SST GGA sub-components to be analyzed are; Compressor Airfoils, Compressor

Casings, Compressor Rotor, Combustor components, SST Stage 1 and Stage 2 Nozzles, SST Stage 1 and Stage 2 Blades, and Fuel Nozzles.

Sub-Components Assembly

Nomenclature P/N

Sub-Components Assembly

Nomenclature P/N

Combustion Chamber Linear

Assembly

9101M29G57

Single Shank Turbine (SST)

High Pressure Turbine (HPT)

Stage 1 Blades

L31424G04

9101M29G59 L31424G29

9101M29G60 L31424G30

9101M29G63 L31424G28

L31424G31

L31033G01

L31033G07 L25645G03

SOW-PWS Template 05 March 2021 version Page 8

Single Shank Turbine (SST)

High Pressure Turbine (HPT)

Stage 1 Nozzles

L31033G02

Single Shank Turbine (SST)

High Pressure Turbine

(HPT)Stage 2 Blades

L25645G14

L31033G08 L25645G06

L25645G05

Single Shank Turbine (SST) High Pressure Turbine (HPT)

Stage 2 Nozzles

L25690G03 L25645G15

L25690G05

L31395G13

Fuel Nozzles

9016M58P06

L25690G04 9016M58P27

L25690G06

L38373G06

L31395G14

L38373G05

L38373G06

Table 2: List of Gas Generator Assembly (GGA) Major Sub-Components for RADCON

Inspection

3.1.2.4 Document the measured level of radiological contamination for each part in paragraph

3.1.2.2 of the Statement of Work. Identify by part number and serial number where applicable. Document radiological background readings. Minor piece parts and components of the same part number can be combined into lots for ease of reporting.

Contractor shall report findings in accordance with CDRL A003.

3.1.3 Disassembly RADCON

3.1.3.1 Compare the results from 3.1.2.2 to levels identified in paragraphs 2.3 and 2.4 of the

Statement of Work (less than 1000 dpm / 100 cm2 loose / removable contaminants and less than 6000 dpm / 100 cm2 total).

3.1.3.2 All items that exceed these limits shall be considered "radiologically contaminated" and subject to RADCON procedures (decontamination).

3.1.3.3 For all remaining items “below the limits”, verify that all uncontaminated parts have been; (1) radiologically surveyed, (2) survey data has been recorded, (3) that the measured contamination levels for every part fall below the requirements contained in this Statement of Work. Minor piece parts and components of the same part number can be combined into lots for ease of reporting. These parts can be identified as clear of radiological contamination and shall be collected and packaged in accordance with MIL-

STD-2073 for return to the USN.

3.1.3.4 Perform RADCON decontamination procedures as applicable to NRC/State license and approved by the USN. Clean the contaminated parts in accordance with Chapter 7.0 in technical manual S9234-AB-MMD-020.

3.1.4 2nd RADCON Readings

3.1.4.1 Parts that had been considered “radiologically contaminated” in paragraph 3.1.3.1 of the

Statement of Work and received RADCON decontamination procedures in paragraph

SOW-PWS Template 05 March 2021 version Page 9

3.1.3.4 of the Statement of Work shall receive a second radiological inspection of all components in accordance with paragraph 2.3 and 2.4 of the Statement of Work.

3.1.4.2 Document the measured level of radiological contamination for each part in paragraph

3.1.4.1 of the Statement of Work. Identify by part number and serial number where applicable. Document and record all new readings and compare with previous radiological readings from paragraph 3.1.2.4 of the Statement of Work. Document radiological background readings. Minor piece parts and components of the same part number can be combined into lots for ease of reporting. Contractor shall report findings in accordance with CDRL A004.

3.1.4.3 All items that exceed these limits in paragraph 2.3 and 2.4 of the Statement of Work shall be considered "radiologically contaminated" packaged, labeled, and disposed of in accordance with the applicable conditions set forth in the contractor’s state license.

3.1.4.4 For all items re-inspected in paragraph 3.1.4.1 Statement of Work that fall “below the limits”, verify that all uncontaminated parts have been; (1) radiologically surveyed, (2) survey data has been recorded, (3) that the measured contamination levels for every part fall below the requirements contained in this Statement of Work. Minor piece parts and components of the same part number can be combined into lots for ease of reporting.

These parts can be identified as clear of radiological contamination and shall be collected and packaged in accordance with commercial practices for return to the USN.

3.1.4.5 The contractor shall collect all contaminated USN parts as identified in 3.1.4.3 of the

Statement of Work as “radiologically contaminated” package in a sealed/safe container suitable for shipment in accordance with applicable state regulations. All containers shall be marked appropriately for shipment in accordance with NRC licensing. Contractor is responsible for disposing the “radiologically contaminated” units in accordance with the contractor’s state license.

3.2 Release of parts from the control area

All parts identified in paragraphs 3.1.3.3, 3.1.4.4, and 3.1.4.5 of the Statement of Work shall be officially released in writing by the USN with shipping instruction.

3.2.1 No parts shall be removed from the control area without the written approval of the USN.

In addition, any removal of parts from the control area shall be performed in accordance with the applicable conditions set forth in the contractor’s agreement state license. Should a conflict arise between the agreement state license and the requirements outlined in this Statement of Work, the contractor shall notify the C/424 Technical Point of Contact (TPOC) in writing requesting guidance prior to release. The C/424 TPOC shall provide a written response to the contractor within thirty (30) days.

3.2.2 The Contractor shall package, seal & preserve all hardware in accordance with best commercial practices and in accordance with ANSI 13.12 & NRC Regulator Guide 1.86. It is the

Contractor’s responsibility to ensure that all applicable codes and standards are followed. The

SOW-PWS Template 05 March 2021 version Page 10

Contractor shall prepare a Packaging Plan for the LM2500 SST GGA parts. The Packaging Plan shall be delivered to and approved by the Government prior to delivery of the LM2500 SST

GGA parts. The packaging plan shall detail the precautions the Contractor plans to use to protect and preserve the GTGs against corrosion, deterioration and physical damage during shipment and handling. The Packaging Plan shall be prepared and submitted IAW CDRL A005 of this

RFP.

3.3 RADCON Disassembly and Inspection Report (RADCON DIR)

The RADCON Disassembly and Inspection Report (RADCON DIR) is the radiological conditional analysis of parts, assemblies or components to document the conditions of parts not meeting the contamination levels of paragraphs 2.3 and 2.4 of the Statement of Work. The analysis of incoming LM2500 SST GGA shall result in a RADCON DIR for all parts identified by part number and, where applicable, serial number.

The contractor shall compile a RADCON DIR in the contractor’s format. This report shall be submitted to Naval Surface Warfare Center, Philadelphia (NSWC-PL) within thirty (30) calendar days of completion of the disassembly, inspection and survey in accordance with CDRL A002, A003, and A004. This report at a minimum shall contain:

3.3.1 Incoming visual inspection identifying physical damage.

3.3.2 Illustration and digital photographs of damage found.

3.3.3 LM2500 SST GGA serial number and all subassembly part numbers and serial numbers where applicable.

3.3.4 All parts or components missing.

3.3.5 RADCON findings summary for each LM2500 SST GGA component.

3.3.6 Conditions found (based upon visual assessment)

3.3.7 All inspection data and damage reports.

3.3.8 Engineering comments.

3.3.9 Survey results of all parts organized in three lists: contaminated, non-contaminated, non-contaminated after cleaning. Lists shall include all applicable part numbers, quantities, and where applicable, serial numbers.

3.3.10 Equipment Reporting: The results shall include the survey equipment used on each part. All survey equipment with applicable calibration information. Included shall be information regarding the minimum detectable activity (MDA) for each instrument used for each radiation type.

4.0 DATA REQUIREMENTS

4.1 Contract Status Report (CDRL A001)

4.1.1 This report shall reflect both prime and Subcontractor data if applicable at the same level of detail.

SOW-PWS Template 05 March 2021 version Page 11

4.1.2 The CDRL shall be delivered electronically, unless otherwise stated, and while

Contractor's format is acceptable the Government's approval must be received in writing from the

COR within 5 business days before formal submission.

4.2 Pre-Disassembly Recordings Report (CDRL A002)

4.2.1 The CDRL shall be delivered electronically, unless otherwise stated, and while

Contractor’s format is acceptable, Government’s approval is required from the COR. This report shall reflect both prime and subcontractor data if applicable at the same level of detail.

4.3 Disassembly Readings Report (CDRL A003)

4.3.1 The CDRL shall be delivered electronically, unless otherwise stated, and while

4.4 2nd Decontamination Readings Report (CDRL A004)

4.4.1 The CDRL shall be delivered electronically, unless otherwise stated, and while

4.5 Packaging Plan (CDRL A005)

4.5.1 The CDRL shall be delivered electronically, unless otherwise stated, and while

5.0 SECURITY REQUIREMENTS

5.1 OPERATIONS SECURITY (OPSEC)

5.1.1 The Contractor shall protect critical information associated with this contract to prevent unauthorized disclosure. The NSWC Philadelphia Division's (NSWCPD) Critical Information List

(CIL)/ CIIL (Critical Indicators and information list) will be provided on site, if warranted.

Performance under this contract requires the contractor to adhere to OPSEC requirements. The

Contractor may not impose OPSEC requirements on its subcontractors unless NSWCPD approves the OPSEC requirements. During the period of this contract, the Contractor may be exposed to, use, or produce, NSWCPD Critical Information (CI) and/or observables and indicators which may lead to discovery of CI. NSWCPD’s CI will not be distributed to unauthorized third parties, including foreign governments, or companies under Foreign Ownership, Control, or Influence

(FOCI).

5.1.2 CUI correspondence transmitted internally on the contractor's unclassified networks or information systems, and externally, shall be protected per NIST SP-800-171, Protecting

Controlled Unclassified Information (CUI) in Non-federal Systems and Organizations.

Assembled large components/systems being transported to and from testing areas, other production or government facilities (whether or not on public roadways) shall be in an enclosed van trailer or covered flatbed trailer. Component/System outside storage, staging, and test areas shall be shielded/obscured from public view wherever physically possible.

SOW-PWS Template 05 March 2021 version Page 12

5.1.3 NSWCPD’s CI shall not be publicized in corporate wide newsletters, trade magazines, displays, intranet pages or public facing websites. Media requests related to this project shall be directed to the PCO, and the COR who will forward the required to the NSWCPD Public Release

Authority for review.

5.1.4 Any attempt by unauthorized third parties to solicit, obtain, photograph, or record, or;

incidents of loss/compromise of government Classified or CI, Business Sensitive, Company

Proprietary information related to this or other program must be immediately reported to the contractor's Facility Security Officer and Cognizant Security Office and/or the Naval Criminal

Investigative Service, and the NSWC PD Security Division (Code 105). Questions concerning these requirements shall be directed to the PCO, and the COR who will forward the request to the NSWC PD Security Division (Code 105).

5.2 RECEIPT, STORAGE, AND GENERATION OF CONTROLLED UNCLASSIFIED

INFORMATION (CUI)

All Controlled Unclassified Information (CUI) associated with this contract must follow the minimum marking requirements of DoDI 5200.48, Section 3, paragraph 3.4.a, and include the acronym "CUI" in the banner and footer of the document. In accordance with DoDI 5200.48, CUI must be safeguarded to prevent Unauthorized Disclosure (UD). CUI export controlled technical information or other scientific, technical, and engineering information must be marked with an export control warning as directed in DoDI 5230.24, DoDD 5230.25, and Part 250 of

Title 32, CFR. Nonfederal information systems storing and processing CUI shall be protected per

NIST SP-800-171, or subsequent revisions. All transmissions to personal email accounts (AOL, Yahoo, Hotmail, Comcast, etc.) and posting on social media websites (Facebook, Instagram, Twitter, LinkedIn, etc.) are prohibited. Destroy CUI associated with this contract by any of the following approved methods: A cross-cut shredder; a certified commercial destruction vendor; a central destruction facility; incineration; chemical decomposition; pulverizing, disintegration; or methods approved for classified destruction.

6.0 PLACE OF PERFORMANCE

6.1 Contractor shall perform at the contractor’s facility.

7.0 TRAVEL

Not applicable.

8.0 GOVERNMENT FURNISHED PROPERTY

8.1 The Government will provide the contaminated gas turbines to the contractor. Contractor shall disassemble, decontaminate, and ship back to the Government.

9.0 GOVERNMENT FURNISHED INFORMATION

SOW-PWS Template 05 March 2021 version Page 13

10.0 PURCHASES

11.0 COUNTERFEIT MATERIAL PREVENTION

12.0 PERSONNEL

13.0 NSWCPD ELECTRONIC COST REPORTING AND FINANCIAL TRACKING

(ECRAFT) SYSTEM

14.0 SPECIAL REQUIREMENTS

14.1 The Government shall identify ship to locations for decontaminated units at the task order level.