Attachment 4- Statement of Work CNC Tube Bender.pdf

DEPARTMENT OF THE AIR FORCE

7TH MAINTENANCE GROUP (AFGSC)

DYESS AIR FORCE BASE TEXAS

Death from above

23 MAY 2024

MEMORANDUM FOR TUBE-LINES TECHNOLOGIES

FROM: 7 EMS/ MXMFS

Fabrication Flight 498 2nd Street Dyess AFB, TX 79607

SUBJECT: Statement of Work for the installation of CNC Tube Bender

1.0 Description of Work. The contractor shall provide all necessary labor, personnel, supervision, management, tools, equipment, transportation, materials, and any other items necessary to provide installation of CNC tube bender. The vendor will provide on-site training for 3 days at building 8130 993 3rd Street Dyess AFB.

1.1 Installation of Bender. The Vendor will provide transportation of the CNC tube bender to building 8130 Dyess AFB Tx. The Vendor will unpack the bender and fully assemble the machine. The Vendor will also verify the operation of the machine and all its functions. The vendor will troubleshoot any issues present at time of install. The Vendor will install the bender in accordance with relevant building codes. The machine must be connected to the circuit breaker in building 8130 located in the mechanical room. The new electrical drop (1) will be installed with a 35 Amp Circuit up to 75 feet from original circuit. The vendor will provide labor and material to the new tube bender.

1.2 Vendor Actions at Worksite. Vendor technicians will maintain 100% accountability and control of all vendor tools and equipment while on the jobsite. At no time should the government be responsible for lost, damaged, missing tools, equipment, or parts that are property of the vendor on the jobsite. Lost tools and equipment will be immediately brought to the attention of section supervision. Additionally, any debris, trash or replacement parts created by the vendor at the jobsite will be disposed of.

Contractor personnel are only to be in their assigned areas and are not allowed in other aircraft maintenance areas without section supervision approval and / or an escort.

1.3 Vendor Checkout (Job Completion). Upon completion of training, the vendor must inform section supervision of completion. The section supervision will inspect all work performed and ensure work has been accomplished IAW this SOW and meets requirements necessary for the Government quality controls. All work areas will be thoroughly checked upon vendor completion of the job and the vendor will not be released until area is inspected.

2.0 General Information

2.1 Recognized Holidays: The contractor may be required to perform service on holidays including but not limited to:

New Year's Day Birthday of Martin Luther King Jr. President's Day Memorial Day Independence Day Labor Day Columbus Day Veteran's Day Thanksgiving Day Christmas Day

2.2 Hours of Operation: The contractor is responsible for conducting business with the individual purchased maintenance plans, except when the government facility is closed due to local or national emergencies, administrative closing, or similar government directed facility closing. The contractor shall not be reimbursed when the government facility is closed for the aforementioned reasons.

2.3 Worker's Health and Safety: The contractor shall comply with all applicable Federal, State and local legal requirements regarding workers' health and safety. The contractor is solely responsible for determining the legal and safety requirements that apply to his/her activities. These include but are not limited to all Occupational Safety and Health Administration (OSHA) safety rules and regulations, arc flash training, personal protection training and equipment to protect themselves and others from unsafe work conditions. The contractor shall report any accidents or OSHA violations immediately to the appropriate authorities and within 24 hours to the PCO. All equipment discussed within this contract shall meet all OSHA, EPA and or any other applicable guidelines. All safety equipment must be used for its intended and designed purpose. Any unsafe acts by the vendor will be reported to vendor supervision and 7 CONS and may be grounds for contract cancelation.

2.4 Security Requirements: The contractor shall comply with all security controls directed by the Government Site POC (i.e. Facility Manager).and or Program Manager.

2.5 Government Property Damage: The contractor shall record and report, within 24 hours, to the PCCIE Program Manager, PCO and designated government site POC, all available facts relating to each instance of accidental damage to government property or injury to either contractor or government personnel. The contractor shall not perform any work on the damaged equipment/property until released by an authorized government representative. If the Government elects to conduct an investigation of the accident, the contractor shall cooperate fully and assist the government personnel until the investigation is completed.

2.6 Damage to Property or Equipment: The Contractor, at their own expense, shall repair any damage to Government property or equipment that can be attributed to the Contractor. Before repairs are made, they must be submitted to the assigned Contracting

Officer (CO) for clearance. Said repairs shall be made by a skilled workman, and to the satisfaction or the Contracting Officer or a designated representative.