Attachment 4 - B1643 - Specs Volume 2.pdf

RENOVATE GENERAL PURPOSE MAINTENANCE

HANGAR, B1643

Naval Air Station Fort Worth Joint Reserve Base, Texas Project Number: DDPM 20-0007

Specifications—100% Submittal VOLUME II of II Divisions 22-33

APRIL 2022

Prepared for:

Air Force Reserve Command

7 Mickey Mantle Dr.

JDM Place Suite 350 Oklahoma City, OK 73104

1612 Specht Point Rd.

Suite 105 Fort Collins, CO 80525

Prepared by:

04/15/2022

This page intentionally left blank.

B1643 Repair Maintenance Hangar NASJRB1643

VOLUME I

DIVISION 01 - GENERAL REQUIREMENTS

01 11 00 SUMMARY OF WORK

01 30 00 ADMINISTRATIVE REQUIREMENTS

01 33 00 SUBMITTAL PROCEDURES

01 33 29 SUSTAINABILITY REQUIREMENTS AND REPORTING

01 35 26 GOVERNMENTAL SAFETY REQUIREMENTS

01 42 00 SOURCES FOR REFERENCE PUBLICATIONS

01 45 00.00 10 QUALITY CONTROL

01 45 00.15 10 RESIDENT MANAGEMENT SYSTEM CONTRACTOR MODE (RMS CM)

01 45 35 SPECIAL INSPECTIONS

01 74 19 CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL

01 78 00 CLOSEOUT SUBMITTALS

01 78 23 OPERATION AND MAINTENANCE DATA

DIVISION 02 - EXISTING CONDITIONS

02 41 00 DEMOLITION

DIVISION 03 - CONCRETE

03 30 00 CAST-IN-PLACE CONCRETE

DIVISION 05 - METALS

05 05 23.16 STRUCTURAL WELDING

05 12 00 STRUCTURAL STEEL

05 50 13 MISCELLANEOUS METAL FABRICATIONS

05 50 14 STRUCTURAL METAL FABRICATIONS

DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES

06 10 00 ROUGH CARPENTRY

06 41 16.00 10 PLASTIC-LAMINATE-CLAD ARCHITECTURAL CABINETS

06 61 16 SOLID SURFACING FABRICATIONS

DIVISION 07 - THERMAL AND MOISTURE PROTECTION

07 42 13 METAL WALL PANELS

07 60 00 FLASHING AND SHEET METAL

07 84 00 FIRESTOPPING

07 92 00 JOINT SEALANTS

DIVISION 08 - OPENINGS

08 11 13 STEEL DOORS AND FRAMES

08 31 00 ACCESS DOORS AND PANELS

08 33 23 OVERHEAD COILING DOORS

08 34 73 SOUND CONTROL DOOR ASSEMBLIES

08 71 00 DOOR HARDWARE

08 81 00 GLAZING

08 91 00 METAL WALL LOUVERS

DIVISION 09 - FINISHES

09 06 00 SCHEDULES FOR FINISHES

09 22 00 SUPPORTS FOR PLASTER AND GYPSUM BOARD

PROJECT TABLE OF CONTENTS Page 1

PROJECT TABLE OF CONTENTS

09 29 00 GYPSUM BOARD

09 30 10 CERAMIC, QUARRY, AND GLASS TILING

09 51 00 ACOUSTICAL CEILINGS

09 62 38 STATIC-CONTROL FLOORING

09 65 00 RESILIENT FLOORING

09 67 23.16 FUEL RESISTIVE RESINOUS FLOORING, 5-COAT SYSTEM (Bid

Option 004)

09 68 00 CARPETING

09 77 20 DECORATIVE FIBERGLASS REINFORCED WALL PANELS

09 90 00 PAINTS AND COATINGS

DIVISION 10 - SPECIALTIES

10 14 00.10 EXTERIOR SIGNAGE

10 14 00.20 INTERIOR SIGNAGE

10 21 13 TOILET COMPARTMENTS

10 26 00 WALL PROTECTION

10 28 13 TOILET ACCESSORIES

10 44 16 FIRE EXTINGUISHERS

10 51 13 METAL LOCKERS

DIVISION 12 - FURNISHINGS

12 59 00 SYSTEMS FURNITURE

DIVISION 21 - FIRE SUPPRESSION

21 13 13 WET PIPE SPRINKLER SYSTEMS, FIRE PROTECTION

21 13 25 HIGH-EXPANSION FOAM SYSTEM, FIRE PROTECTION

VOLUME II

DIVISION 22 - PLUMBING

22 00 00 PLUMBING, GENERAL PURPOSE

22 05 48.00 20 MECHANICAL SOUND, VIBRATION, AND SEISMIC CONTROL

22 07 19.00 40 PLUMBING PIPING INSULATION

22 15 14.00 40

GENERAL SERVICE COMPRESSED-AIR SYSTEMS, LOW PRESSURE

DIVISION 23 - HEATING, VENTILATING, AND AIR CONDITIONING (HVAC)

23 03 00.00 20 BASIC MECHANICAL MATERIALS AND METHODS

23 05 15 COMMON PIPING FOR HVAC

23 05 48.00 40 VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND

EQUIPMENT

23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC

23 07 00 THERMAL INSULATION FOR MECHANICAL SYSTEMS

23 09 00 INSTRUMENTATION AND CONTROL FOR HVAC

23 09 13 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC

23 23 00 REFRIGERANT PIPING

23 31 13.00 40 METAL DUCTS

23 34 23.00 40 HVAC POWER VENTILATORS

23 36 00.00 40 AIR TERMINAL UNITS

23 37 13.00 40 DIFFUSERS, REGISTERS, AND GRILLES

23 81 00 DECENTRALIZED UNITARY HVAC EQUIPMENT

23 81 29 VARIABLE REFRIGERANT FLOW HVAC SYSTEMS

23 82 46.00 40 ELECTRIC UNIT HEATERS

23 83 00.00 20 ELECTRIC SPACE HEATING EQUIPMENT

PROJECT TABLE OF CONTENTS Page 2

1250709290C Cross-Out

26 05 00.00 40 COMMON WORK RESULTS FOR ELECTRICAL

26 05 19.10 10 INSULATED WIRE AND CABLE

26 05 26.00 40 GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS

26 05 71.00 40 LOW VOLTAGE OVERCURRENT PROTECTIVE DEVICES

26 09 23.00 40 LIGHTING CONTROL DEVICES

26 20 00 INTERIOR DISTRIBUTION SYSTEM

26 24 16.00 40 PANELBOARDS

26 35 44 270 VDC SOLID STATE CONVERTER

26 51 00 INTERIOR LIGHTING

26 53 00.00 40 EXIT SIGNS

26 56 00 EXTERIOR LIGHTING

DIVISION 27 - COMMUNICATIONS

27 05 28.36 40 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS

27 10 00 BUILDING TELECOMMUNICATIONS CABLING SYSTEM

27 13 23.00 40 COMMUNICATIONS OPTICAL BACKBONE CABLING

DIVISION 28 - ELECTRONIC SAFETY AND SECURITY

28 10 05 ELECTRONIC SECURITY SYSTEMS (ESS)

28 31 76 INTERIOR FIRE ALARM AND MASS NOTIFICATION SYSTEM,

ADDRESSABLE

DIVISION 32 - EXTERIOR IMPROVEMENTS

32 13 13.06 PORTLAND CEMENT CONCRETE PAVEMENT FOR ROADS AND SITE

FACILITIES

DIVISION 33 - UTILITIES

33 11 00 WATER UTILITY DISTRIBUTION PIPING

33 30 00 SANITARY SEWERAGE

33 71 02 UNDERGROUND ELECTRICAL DISTRIBUTION

33 82 00 TELECOMMUNICATIONS OUTSIDE PLANT (OSP)

-- End of Project Table of Contents --

PROJECT TABLE OF CONTENTS Page 3

DIVISION 26 - ELECTRICAL

This page intentionally left blank.

B1643 Repai r Mai nt enance Hangar NASJRB1643

SECTI ON 22 00 00

PLUMBI NG, GENERAL PURPOSE

11/ 15, CHG 4: 05/ 21

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

AI R- CONDI TI ONI NG, HEATI NG AND REFRI GERATI ON I NSTI TUTE ( AHRI )

AHRI 1010 ( 2002) Sel f - Cont ai ned, Mechani cal l y Ref r i ger at ed Dr i nki ng- Wat er Cool er s

AMERI CAN SOCI ETY OF MECHANI CAL ENGI NEERS ( ASME)

ASME A112. 6. 1M ( 1997; R 2017) Fl oor Af f i xed Suppor t s f or Of f - t he- Fl oor Pl umbi ng Fi xt ur es f or Publ i c Use

ASME A112. 6. 3 ( 2019) St andar d f or Fl oor and Tr ench Dr ai ns

ASME A112. 19. 2/ CSA B45. 1 ( 2018; ERTA 2018) St andar d f or Vi t r eous Chi na Pl umbi ng Fi xt ur es and Hydr aul i c Requi r ement s f or Wat er Cl oset s and Ur i nal s

ASME A112. 19. 5 ( 2017) Fl ush Val ves and Spuds f or Wat er Cl oset s, Ur i nal s, and Tanks

ASME B1. 20. 1 ( 2013; R 2018) Pi pe Thr eads, Gener al Pur pose ( I nch)

ASME B16. 5 ( 2020) Pi pe Fl anges and Fl anged Fi t t i ngs NPS 1/ 2 Thr ough NPS 24 Met r i c/ I nch St andar d

ASME B16. 12 ( 2019) Cast I r on Thr eaded Dr ai nage Fi t t i ngs

ASME B16. 15 ( 2018) Cast Copper Al l oy Thr eaded Fi t t i ngs Cl asses 125 and 250

ASME B16. 18 ( 2018) Cast Copper Al l oy Sol der Joi nt Pr essur e Fi t t i ngs

ASME B16. 21 ( 2016) Nonmet al l i c Fl at Gasket s f or Pi pe Flanges

ASME B16. 22 ( 2018) St andar d f or Wr ought Copper and Copper Al l oy Sol der Joi nt Pr essur e Fi t t i ngs

ASME B16. 50 ( 2013) Wr ought Copper and Copper Al l oy Br aze- Joi nt Pr essur e Fi t t i ngs

ASME B16. 51 ( 2013) Copper and Copper Al l oy Pr ess- Connect Pr essur e Fi t t i ngs

SECTI ON 22 00 00 Page 1

ASME B40. 100 ( 2013) Pr essur e Gauges and Gauge Attachments

AMERI CAN SOCI ETY OF SANI TARY ENGI NEERI NG ( ASSE)

ASSE 1010 ( 2004) Per f or mance Requi r ement s f or Wat er Hammer Ar r est er s ( ANSI appr oved 2004)

ASSE 1018 ( 2001; R 2021) Per f or mance Requi r ement s f or Tr ap Seal Pr i mer Val ves - Pot abl e Wat er Suppl i ed ( ANSI Appr oved 2002

AMERI CAN WATER WORKS ASSOCI ATI ON ( AWWA)

AWWA B300 ( 2018) Hypochl or i t es

AWWA B301 ( 2018) Li qui d Chl or i ne

AWWA C606 ( 2015) Gr ooved and Shoul der ed Joi nt s

AWWA C651 ( 2014) St andar d f or Di s i nf ect i ng Wat er Mains

AWWA C652 ( 2019) Di s i nf ect i on of Wat er - St or age Facilities

ASTM I NTERNATI ONAL ( ASTM)

ASTM A74 ( 2021) St andar d Speci f i cat i on f or Cast I r on Soi l Pi pe and Fi t t i ngs

ASTM A105/ A105M ( 2021) St andar d Speci f i cat i on f or Car bon St eel For gi ngs f or Pi pi ng Appl i cat i ons

ASTM A183 ( 2020) St andar d Speci f i cat i on f or Car bon St eel Tr ack Bol t s and Nut s

ASTM A193/ A193M ( 2020) St andar d Speci f i cat i on f or Al l oy- St eel and St ai nl ess St eel Bol t i ng Mat er i al s f or Hi gh- Temper at ur e Ser vi ce and Ot her Speci al Pur pose Appl i cat i ons

ASTM A515/ A515M ( 2017) St andar d Speci f i cat i on f or Pr essur e Vessel Pl at es, Car bon St eel , f or I nt er medi at e- and Hi gher - Temper at ur e Service

ASTM A516/ A516M ( 2017) St andar d Speci f i cat i on f or Pr essur e Vessel Pl at es, Car bon St eel , f or Moder at e-and Lower - Temper at ur e Ser vi ce

ASTM A536 ( 2019) St andar d Speci f i cat i on f or Duct i l e I r on Cast i ngs

ASTM A888 ( 2021) St andar d Speci f i cat i on f or Hubl ess Cast I r on Soi l Pi pe and Fi t t i ngs f or Sani t ar y and St or m Dr ai n, Wast e, and Vent Pi pi ng Appl i cat i ons

SECTI ON 22 00 00 Page 2

ASTM B32 ( 2020) St andar d Speci f i cat i on f or Sol der Metal

ASTM B42 ( 2020) St andar d Speci f i cat i on f or Seaml ess Copper Pi pe, St andar d Si zes

ASTM B88 ( 2020) St andar d Speci f i cat i on f or Seaml ess Copper Wat er Tube

ASTM B88M ( 2020) St andar d Speci f i cat i on f or Seaml ess Copper Wat er Tube ( Met r i c)

ASTM B584 ( 2014) St andar d Speci f i cat i on f or Copper Al l oy Sand Cast i ngs f or Gener al Applications

ASTM B813 ( 2016) St andar d Speci f i cat i on f or Li qui d and Past e Fl uxes f or Sol der i ng of Copper and Copper Al l oy Tube

ASTM B828 ( 2016) St andar d Pr act i ce f or Maki ng Capi l l ar y Joi nt s by Sol der i ng of Copper and Copper Al l oy Tube and Fi t t i ngs

ASTM C564 ( 2020a) St andar d Speci f i cat i on f or Rubber Gasket s f or Cast I r on Soi l Pi pe and Fittings

ASTM C920 ( 2018) St andar d Speci f i cat i on f or El ast omer i c Joi nt Seal ant s

ASTM D2000 ( 2018) St andar d Cl assi f i cat i on Syst em f or Rubber Pr oduct s i n Aut omot i ve Appl i cat i ons

ASTM D2564 ( 2012) St andar d Speci f i cat i on f or Sol vent Cement s f or Pol y( Vi nyl Chl or i de) ( PVC) Pl ast i c Pi pi ng Syst ems

ASTM D2665 ( 2014) St andar d Speci f i cat i on f or Pol y( Vi nyl Chl or i de) ( PVC) Pl ast i c Dr ai n, Wast e, and Vent Pi pe and Fi t t i ngs

ASTM D2855 ( 2015) St andar d Pr act i ce f or Maki ng Sol vent - Cement ed Joi nt s wi t h Pol y( Vi nyl Chl or i de) ( PVC) Pi pe and Fi t t i ngs

ASTM D3138 ( 2004; R 2016) St andar d Speci f i cat i on f or Sol vent Cement s f or Tr ansi t i on Joi nt s Bet ween Acr yl oni t r i l e- But adi ene- St yr ene ( ABS) and Pol y( Vi nyl Chl or i de) ( PVC) Non- Pr essur e Pi pi ng Component s

ASTM D3139 ( 2019) Joi nt s f or Pl ast i c Pr essur e Pi pes Usi ng Fl exi bl e El ast omer i c Seal s

ASTM D3212 ( 2007; R 2020) St andar d Speci f i cat i on f or Joi nt s f or Dr ai n and Sewer Pl ast i c Pi pes Usi ng Fl exi bl e El ast omer i c Seal s

SECTI ON 22 00 00 Page 3

ASTM D3311 ( 2017) St andar d Speci f i cat i on f or Dr ai n, Wast e, and Vent ( DWV) Pl ast i c Fi t t i ngs Patterns

ASTM E1 ( 2014) St andar d Speci f i cat i on f or ASTM Li qui d- i n- Gl ass Ther momet er s

ASTM F409 ( 2017) St andar d Speci f i cat i on f or Ther mopl ast i c Accessi bl e and Repl aceabl e Pl ast i c Tube and Tubul ar Fi t t i ngs

ASTM F477 ( 2014) St andar d Speci f i cat i on f or El ast omer i c Seal s ( Gasket s) f or Joi ni ng Pl ast i c Pi pe

ASTM F493 ( 2020) St andar d Speci f i cat i on f or Sol vent Cement s f or Chl or i nat ed Pol y ( Vi nyl Chl or i de) ( CPVC) Pl ast i c Pi pe and Fi t t i ngs

ASTM F891 ( 2016) St andar d Speci f i cat i on f or Coext r uded Pol y ( Vi nyl Chl or i de) ( PVC) Pl ast i c Pi pe wi t h a Cel l ul ar Cor e

ASTM F1760 ( 2016; R 2020) St andar d Speci f i cat i on f or Coext r uded Pol y( Vi nyl Chl or i de) ( PVC) Non- Pr essur e Pl ast i c Pi pe Havi ng Repr ocessed- Recycl ed Cont ent

ASTM F2389 ( 2021) St andar d Speci f i cat i on f or Pr essur e- r at ed Pol ypr opyl ene ( PP) Pi pi ng Systems

CAST I RON SOI L PI PE I NSTI TUTE ( CI SPI )

CI SPI 301 ( 2018) Hubl ess Cast I r on Soi l Pi pe and Fi t t i ngs f or Sani t ar y and St or m Dr ai n, Wast e, and Vent Pi pi ng Appl i cat i ons

CI SPI 310 ( 2012) Coupl i ng f or Use i n Connect i on wi t h Hubl ess Cast I r on Soi l Pi pe and Fi t t i ngs f or Sani t ar y and St or m Dr ai n, Wast e, and Vent Pi pi ng Appl i cat i ons

COPPER DEVELOPMENT ASSOCI ATI ON ( CDA)

CDA A4015 ( 2016; 14/ 17) Copper Tube Handbook

I NTERNATI ONAL ASSOCI ATI ON OF PLUMBI NG AND MECHANI CAL OFFI CI ALS

(IAPMO)

I APMO PS 117 ( 2005b) Pr ess Type Or Pl ai n End Rub Gasket ed W/ Nai l CU & CU Al l oy Fi t t i ngs 4 I nst al l On CU Tubi ng

I APMO UPC ( 2003) Uni f or m Pl umbi ng Code

SECTI ON 22 00 00 Page 4

I NTERNATI ONAL CODE COUNCI L ( I CC)

I CC A117. 1 COMM ( 2017) St andar d And Comment ar y Accessi bl e and Usabl e Bui l di ngs and Faci l i t i es

I CC I PC ( 2021) I nt er nat i onal Pl umbi ng Code

I NTERNATI ONAL SAFETY EQUI PMENT ASSOCI ATI ON ( I SEA)

ANSI / I SEA Z358. 1 ( 2014) Amer i can Nat i onal St andar d f or Emer gency Eyewash and Shower Equi pment

MANUFACTURERS STANDARDI ZATI ON SOCI ETY OF THE VALVE AND FI TTI NGS

I NDUSTRY ( MSS)

MSS SP- 25 ( 2018) St andar d Mar ki ng Syst em f or Val ves, Fi t t i ngs, Fl anges and Uni ons

MSS SP- 58 ( 2018) Pi pe Hanger s and Suppor t s - Mat er i al s, Desi gn and Manuf act ur e, Sel ect i on, Appl i cat i on, and I nst al l at i on

MSS SP- 80 ( 2019) Br onze Gat e, Gl obe, Angl e and Check Valves

MSS SP- 85 ( 2011) Gr ay I r on Gl obe & Angl e Val ves Fl anged and Thr eaded Ends

NSF I NTERNATI ONAL ( NSF)

NSF 372 ( 2016) Dr i nki ng Wat er Syst em Component s - Lead Cont ent

NSF/ ANSI 14 ( 2020) Pl ast i cs Pi pi ng Syst em Component s and Rel at ed Mat er i al s

NSF/ ANSI 61 ( 2020) Dr i nki ng Wat er Syst em Component s - Heal t h Ef f ect s

PLASTI C PI PE AND FI TTI NGS ASSOCI ATI ON ( PPFA)

PPFA Fi r e Man ( 2016) Fi r est oppi ng: Pl ast i c Pi pe i n Fi r e Resi st i ve Const r uct i on

PLUMBI NG AND DRAI NAGE I NSTI TUTE ( PDI )

PDI WH 201 ( 2010) Wat er Hammer Ar r est er s St andar d

U. S. DEPARTMENT OF ENERGY ( DOE)

Ener gy St ar ( 1992; R 2006) Ener gy St ar Ener gy Ef f i c i ency Label i ng Syst em ( FEMP)

U. S. ENVI RONMENTAL PROTECTI ON AGENCY ( EPA)

EPA SM 9223 ( 2004) Enzyme Subst r at e Col i f or m Test

PL 93- 523 ( 1974; A 1999) Saf e Dr i nki ng Wat er Act

SECTI ON 22 00 00 Page 5

U. S. NATI ONAL ARCHI VES AND RECORDS ADMI NI STRATI ON ( NARA)

40 CFR 141. 80 Nat i onal Pr i mar y Dr i nki ng Wat er Regul at i ons; Cont r ol of Lead and Copper ;

Gener al Requi r ement s

1. 2 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" or " S" c l assi f i cat i on. Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00

SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Pl umbi ng Syst em; G

Det ai l dr awi ngs consi st i ng of schedul es, per f or mance char t s, i nst r uct i ons, di agr ams, and ot her i nf or mat i on t o i l l ust r at e t he r equi r ement s and oper at i ons of syst ems t hat ar e not cover ed by t he Pl umbi ng Code.

SD- 03 Pr oduct Dat a

Shower Faucet s; G

Fixtures

Li st of i nst al l ed f i x t ur es wi t h manuf act ur er , model , and f l ow rate.

Fl ush Val ve Wat er Cl oset s

Fl ush Val ve Ur i nal s

Count er t op Lavat or i es

Ki t chen Si nks

Ser vi ce Si nks

Dr i nki ng- Wat er Cool er s; G

Wat er Sense Label f or Shower head; S

Det ai l s of v i br at i on- absor bi ng f eat ur es, i ncl udi ng ar r angement , f oundat i on pl an, di mensi ons and speci f i cat i ons.

SD- 06 Test Repor t s

Test s, Fl ushi ng and Di si nf ect i on

Test r epor t s i n bookl et f or m showi ng al l f i el d t est s per f or med t o adj ust each component and al l f i el d t est s per f or med t o pr ove compl i ance wi t h t he speci f i ed per f or mance cr i t er i a, compl et i on and t est i ng of t he i nst al l ed syst em. Each t est r epor t shal l i ndi cat e t he f i nal posi t i on of cont r ol s.

SD- 10 Oper at i on and Mai nt enance Dat a

SECTI ON 22 00 00 Page 6

Pl umbi ng Syst em; G

1. 3 STANDARD PRODUCTS

Speci f i ed mat er i al s and equi pment shal l be st andar d pr oduct s of a manuf act ur er r egul ar l y engaged i n t he manuf act ur e of such pr oduct s.

Speci f i ed equi pment shal l essent i al l y dupl i cat e equi pment t hat has per f or med sat i sf act or i l y at l east t wo year s pr i or t o bi d openi ng.

St andar d pr oduct s shal l have been i n sat i sf act or y commer ci al or i ndust r i al use f or 2 year s pr i or t o bi d openi ng. The 2- year use shal l i ncl ude appl i cat i ons of equi pment and mat er i al s under s i mi l ar c i r cumst ances and of s i mi l ar s i ze. The pr oduct shal l have been f or sal e on t he commer ci al mar ket t hr ough adver t i sement s, manuf act ur er s ' cat al ogs, or br ochur es dur i ng t he 2 year per i od.

1. 3. 1 Manuf act ur er ' s Namepl at e

Each i t em of equi pment shal l have a namepl at e bear i ng t he manuf act ur er ' s name, addr ess, model number , and ser i al number secur el y af f i xed i n a conspi cuous pl ace; t he namepl at e of t he di st r i but i ng agent wi l l not be acceptable.

1. 3. 2 Modi f i cat i on of Ref er ences

I n each of t he publ i cat i ons r ef er r ed t o her ei n, consi der t he advi sor y pr ovi s i ons t o be mandat or y, as t hough t he wor d, " shal l " had been subst i t ut ed f or " shoul d" wher ever i t appear s. I nt er pr et r ef er ences i n t hese publ i cat i ons t o t he " aut hor i t y havi ng j ur i sdi ct i on" , or wor ds of s i mi l ar meani ng, t o mean t he Cont r act i ng Of f i cer .

1. 3. 2. 1 Definitions

For t he I nt er nat i onal Code Counci l ( I CC) Codes r ef er enced i n t he cont r act document s, advi sor y pr ovi s i ons shal l be consi der ed mandat or y, t he wor d " shoul d" shal l be i nt er pr et ed as " shal l . " Ref er ence t o t he " code of f i c i al " shal l be i nt er pr et ed t o mean t he " Cont r act i ng Of f i cer . " For Navy owned pr oper t y, r ef er ences t o t he " owner " shal l be i nt er pr et ed t o mean t he " Cont r act i ng Of f i cer . " For l eased f aci l i t i es, r ef er ences t o t he " owner " shal l be i nt er pr et ed t o mean t he " l essor . " Ref er ences t o t he " per mi t hol der " shal l be i nt er pr et ed t o mean t he " Cont r act or . "

1. 3. 2. 2 Admi ni st r at i ve I nt er pr et at i ons

For I CC Codes r ef er enced i n t he cont r act document s, t he pr ovi s i ons of Chapt er 1, " Admi ni st r at or , " do not appl y. These admi ni st r at i ve r equi r ement s ar e cover ed by t he appl i cabl e Feder al Acqui s i t i on Regul at i ons ( FAR) i ncl uded i n t hi s cont r act and by t he aut hor i t y gr ant ed t o t he Of f i cer i n Char ge of Const r uct i on t o admi ni st er t he const r uct i on of t hi s pr oj ect . Ref er ences i n t he I CC Codes t o sect i ons of Chapt er 1, shal l be appl i ed appr opr i at el y by t he Cont r act i ng Of f i cer as aut hor i zed by hi s admi ni st r at i ve cogni zance and t he FAR.

1. 4 DELI VERY, STORAGE, AND HANDLI NG

Handl e, st or e, and pr ot ect equi pment and mat er i al s t o pr event damage bef or e and dur i ng i nst al l at i on i n accor dance wi t h t he manuf act ur er ' s r ecommendat i ons, and as appr oved by t he Cont r act i ng Of f i cer . Repl ace damaged or def ect i ve i t ems.

SECTI ON 22 00 00 Page 7

1. 5 REGULATORY REQUI REMENTS

Unl ess ot her wi se r equi r ed her ei n, pl umbi ng wor k shal l be i n accor dance with I CC I PC.

1. 6 PROJECT/ SI TE CONDI TI ONS

The Cont r act or shal l become f ami l i ar wi t h det ai l s of t he wor k, ver i f y di mensi ons i n t he f i el d, and advi se t he Cont r act i ng Of f i cer of any di scr epancy bef or e per f or mi ng any wor k.

1. 7 I NSTRUCTI ON TO GOVERNMENT PERSONNEL

When speci f i ed i n ot her sect i ons, f ur ni sh t he ser vi ces of compet ent i nst r uct or s t o gi ve f ul l i nst r uct i on t o t he desi gnat ed Gover nment per sonnel i n t he adj ust ment , oper at i on, and mai nt enance, i ncl udi ng per t i nent saf et y r equi r ement s, of t he speci f i ed equi pment or syst em.

I nst r uct or s shal l be t hor oughl y f ami l i ar wi t h al l par t s of t he i nst al l at i on and shal l be t r ai ned i n oper at i ng t heor y as wel l as pr act i cal oper at i on and mai nt enance wor k.

I nst r uct i on shal l be gi ven dur i ng t he f i r st r egul ar wor k week af t er t he equi pment or syst em has been accept ed and t ur ned over t o t he Gover nment f or r egul ar oper at i on. The number of man- days ( 8 hour s per day) of i nst r uct i on f ur ni shed shal l be as speci f i ed i n t he i ndi v i dual sect i on.

When mor e t han 4 man- days of i nst r uct i on ar e speci f i ed, use appr oxi mat el y hal f of t he t i me f or c l assr oom i nst r uct i on. Use ot her t i me f or i nst r uct i on wi t h t he equi pment or syst em.

When si gni f i cant changes or modi f i cat i ons i n t he equi pment or syst em ar e made under t he t er ms of t he cont r act , pr ovi de addi t i onal i nst r uct i on t o acquai nt t he oper at i ng per sonnel wi t h t he changes or modi f i cat i ons.

1. 8 ACCESSI BI LI TY OF EQUI PMENT

I nst al l al l wor k so t hat par t s r equi r i ng per i odi c i nspect i on, oper at i on, mai nt enance, and r epai r ar e r eadi l y accessi bl e. I nst al l conceal ed val ves, expansi on j oi nt s, cont r ol s, damper s, and equi pment r equi r i ng access, i n l ocat i ons f r eel y accessi bl e t hr ough access door s.

PART 2 PRODUCTS

2. 1 MATERIALS

Mat er i al s f or var i ous ser vi ces shal l be i n accor dance wi t h TABLES I and I I .

Pi pe schedul es shal l be sel ect ed based on ser vi ce r equi r ement s. Pi pe f i t t i ngs shal l be compat i bl e wi t h t he appl i cabl e pi pe mat er i al s. Pl ast i c pi pe, f i t t i ngs, and sol vent cement shal l meet NSF/ ANSI 14 and shal l be NSF l i s t ed f or t he ser vi ce i nt ended. Pl ast i c pi pe, f i t t i ngs, and sol vent cement used f or pot abl e hot and col d wat er ser vi ce shal l bear t he NSF seal " NSF- PW. " Pol ypr opyl ene pi pe and f i t t i ngs shal l conf or m t o di mensi onal r equi r ement s of Schedul e 40, I r on Pi pe si ze and shal l compl y wi t h NSF/ ANSI 14, NSF/ ANSI 61 and ASTM F2389. Pol ypr opyl ene pi pi ng t hat wi l l be exposed t o UV l i ght shal l be pr ovi ded wi t h a Fact or y appl i ed UV r esi st ant coat i ng. Pi pe t hr eads ( except dr y seal ) shal l conf or m t o ASME B1. 20. 1. Gr ooved pi pe coupl i ngs and f i t t i ngs shal l be f r om t he same manuf act ur er . Mat er i al or equi pment cont ai ni ng a wei ght ed aver age of gr eat er t han 0. 25 per cent l ead shal l not be used i n any pot abl e wat er syst em i nt ended f or human consumpt i on, and shal l be cer t i f i ed i n

SECTI ON 22 00 00 Page 8 accor dance wi t h NSF/ ANSI 61, Annex G or NSF 372. I n l i ne devi ces such as wat er met er s, bui l di ng val ves, check val ves, met er st ops, val ves, f i t t i ngs and back f l ow pr event er s shal l compl y wi t h PL 93- 523 and NSF/ ANSI 61, Sect i on 8. End poi nt devi ces such as dr i nki ng wat er f ount ai ns, l avat or y f aucet s, k i t chen and bar f aucet s, r esi dent i al i ce maker s, suppl y st ops and end poi nt cont r ol val ves used t o di spense wat er f or dr i nki ng must meet t he r equi r ement s of NSF/ ANSI 61, Sect i on 9. Hubl ess cast - i r on soi l pi pe shal l not be i nst al l ed under gr ound, under concr et e f l oor s l abs, or i n cr awl spaces bel ow ki t chen f l oor s. Pl ast i c pi pe shal l not be i nst al l ed i n ai r pl enums. Pl ast i c pi pe shal l not be i nst al l ed i n a pr essur e pi pi ng syst em i n bui l di ngs gr eat er t han t hr ee st or i es i ncl udi ng any basement l evel s.

2. 1. 1 Pi pe Joi nt Mat er i al s

Gr ooved pi pe and hubl ess cast - i r on soi l pi pe shal l not be used under gr ound. Sol der cont ai ni ng l ead shal l not be used wi t h copper pi pe.

Cast i r on soi l pi pe and f i t t i ngs shal l be mar ked wi t h t he col l ect i ve t r ademar k of t he Cast I r on Soi l I nst i t ut e. Joi nt s and gasket mat er i al s shal l conf or m t o t he f ol l owi ng:

a. Coupl i ng f or Cast - I r on Pi pe: f or hub and spi got t ype ASTM A74, AWWA C606. For hubl ess t ype: CI SPI 310

b. Coupl i ng f or St eel Pi pe: AWWA C606.

c. Coupl i ngs f or Gr ooved Pi pe: Duct i l e I r on ASTM A536 ( Gr ade 65- 45- 12) .

d. Fl ange Gasket s: Gasket s shal l be made of non- asbest os mat er i al i n accor dance wi t h ASME B16. 21. Gasket s shal l be f l at , 1/ 16 i nch t hi ck, and cont ai n Ar ami d f i ber s bonded wi t h St yr ene But adi ene Rubber ( SBR) or Ni t r o But adi ene Rubber ( NBR) . Gasket s shal l be t he f ul l f ace or sel f cent er i ng f l at r i ng t ype. Gasket s used f or hydr ocar bon ser vi ce shal l be bonded wi t h NBR.

e. Br azi ng Mat er i al : Br azi ng mat er i al shal l conf or m t o AWS A5. 8/ A5. 8M, BCuP-5.

f . Br azi ng Fl ux: Fl ux shal l be i n past e or l i qui d f or m appr opr i at e f or use wi t h br azi ng mat er i al . Fl ux shal l be as f ol l ows: l ead- f r ee; have a 100 per cent f l ushabl e r esi due; cont ai n s l i ght l y aci di c r eagent s;

cont ai n pot assi um bor i des; and cont ai n f l uor i des.

g. Sol der Mat er i al : Sol der met al shal l conf or m t o ASTM B32.

h. Sol der Fl ux: Fl ux shal l be l i qui d f or m, non- cor r osi ve, and conf or m t o ASTM B813, St andar d Test 1.

i . PTFE Tape: PTFE Tape, f or use wi t h Thr eaded Met al or Pl ast i c Pi pe.

j . Rubber Gasket s f or Cast - I r on Soi l - Pi pe and Fi t t i ngs ( hub and spi got t ype and hubl ess t ype) : ASTM C564.

k. Rubber Gasket s f or Gr ooved Pi pe: ASTM D2000, maxi mum t emper at ur e 230 degr ees F.

l . Fl exi bl e El ast omer i c Seal s: ASTM D3139, ASTM D3212 or ASTM F477.

m. Bol t s and Nut s f or Gr ooved Pi pe Coupl i ngs: Heat - t r eat ed car bon st eel , ASTM A183.

SECTI ON 22 00 00 Page 9

n. Sol vent Cement f or Tr ansi t i on Joi nt s bet ween ABS and PVC Nonpr essur e Pi pi ng Component s: ASTM D3138.

o. Pl ast i c Sol vent Cement f or PVC Pl ast i c Pi pe: ASTM D2564 and ASTM D2855.

p. Pl ast i c Sol vent Cement f or CPVC Pl ast i c Pi pe: ASTM F493.

q. Fl anged f i t t i ngs i ncl udi ng, but not l i mi t ed t o, f l anges, bol t s, nut s and bol t pat t er ns shal l be i n accor dance wi t h ASME B16. 5 c l ass 150 and shal l have t he manuf act ur er ' s t r ademar k af f i xed i n accor dance wi t h MSS SP- 25. Fl ange mat er i al shal l conf or m t o ASTM A105/ A105M. Bl i nd f l ange mat er i al shal l conf or m t o ASTM A516/ A516M col d ser vi ce and ASTM A515/ A515M f or hot ser vi ce. Bol t s shal l be hi gh st r engt h or i nt er medi at e st r engt h wi t h mat er i al conf or mi ng t o ASTM A193/ A193M.

r . Pr ess f i t t i ngs f or Copper Pi pe and Tube: Copper pr ess f i t t i ngs shal l conf or m t o t he mat er i al and si z i ng r equi r ement s of ASME B16. 51 and per f or mance cr i t er i a of I APMO PS 117. Seal i ng el ement s f or copper pr ess f i t t i ngs shal l be EPDM, FKM or HNBR. Seal i ng el ement s shal l be f act or y i nst al l ed or an al t er nat i ve suppl i ed f i t t i ng manuf act ur er .

Seal i ng el ement shal l be sel ect ed based on manuf act ur er ' s appr oved appl i cat i on gui del i nes.

s. Copper t ubi ng shal l conf or m t o ASTM B88, Type K, L or M.

2. 1. 2 Mi scel l aneous Mat er i al s

Mi scel l aneous mat er i al s shal l conf or m t o t he f ol l owi ng:

a. Wat er Hammer Ar r est er : PDI WH 201. Wat er hammer ar r est er shal l be di aphr agm or pi st on t ype.

b. Hypochl or i t es: AWWA B300.

c. Li qui d Chl or i ne: AWWA B301.

d. Gauges - Pr essur e and Vacuum I ndi cat i ng Di al Type - El ast i c El ement :

ASME B40. 100.

e. Ther momet er s: ASTM E1. Mer cur y shal l not be used i n t her momet er s.

2. 2 PI PE HANGERS, I NSERTS, AND SUPPORTS

Pi pe hanger s, i nser t s, and suppor t s shal l conf or m t o MSS SP- 58.

2. 3 VALVES

Val ves shal l be pr ovi ded on suppl i es t o equi pment and f i xt ur es. Val ves 2- 1/ 2 i nches and smal l er shal l be br onze wi t h t hr eaded bodi es f or pi pe and sol der - t ype connect i ons f or t ubi ng. Val ves 3 i nches and l ar ger shal l have f l anged i r on bodi es and br onze t r i m. Pr essur e r at i ngs shal l be based upon t he appl i cat i on. Gr ooved end val ves may be pr ovi ded i f t he manuf act ur er cer t i f i es t hat t he val ves meet t he per f or mance r equi r ement s of appl i cabl e MSS st andar d. Val ves shal l conf or m t o t he f ol l owi ng st andar ds:

SECTI ON 22 00 00 Page 10

Description Standard

Br onze Gat e, Gl obe, Angl e, and Check Val ves MSS SP- 80

Cast - I r on Gl obe and Angl e Val ves, Fl anged and Thr eaded Ends

MSS SP- 85

Vacuum Rel i ef Val ves ANSI Z21. 22/ CSA 4. 4

2. 3. 1 Wal l Faucet s

Wal l f aucet s wi t h vacuum- br eaker backf l ow pr event er shal l be br ass wi t h 3/ 4 i nch mal e i nl et t hr eads, hexagon shoul der , and 3/ 4 i nch hose connect i on. Faucet handl e shal l be secur el y at t ached t o st em.

2. 3. 2 Ther most at i c Mi xi ng Val ves

Pr ovi de t her most at i c mi xi ng val ve f or l avat or y f aucet s. Mi xi ng val ves, t her most at i c t ype, pr essur e- bal anced or combi nat i on t her most at i c and pr essur e- bal anced shal l be l i ne s i ze and shal l be const r uct ed wi t h r ough or f i ni sh bodi es ei t her wi t h or wi t hout pl at i ng. Each val ve shal l be const r uct ed t o cont r ol t he mi xi ng of hot and col d wat er and t o del i ver wat er at a desi r ed t emper at ur e r egar dl ess of pr essur e or i nput t emper at ur e changes. The cont r ol el ement shal l be of an appr oved t ype. The body shal l be of heavy cast br onze, and i nt er i or par t s shal l be br ass, br onze, cor r osi on- r esi st i ng st eel or copper . The val ve shal l be equi pped wi t h necessar y st ops, check val ves, uni ons, and sedi ment st r ai ner s on t he i nl et s. Mi xi ng val ves shal l mai nt ai n wat er t emper at ur e wi t hi n 5 degr ees F of any set t i ng.

2. 4 FIXTURES

Wat er c l oset r epl acement s i n maj or r enovat i ons may have a f l ush val ve of up t o 1. 6 GPF t o accommodat e exi st i ng pl umbi ng capaci t y. Fi xt ur es f or use by t he physi cal l y handi capped shal l be i n accor dance wi t h I CC A117. 1 COMM. Vi t r eous Chi na, nonabsor bent , har d- bur ned, and vi t r i f i ed t hr oughout t he body shal l be pr ovi ded. Por cel ai n enamel ed war e shal l have speci al l y sel ect ed, c l ear whi t e, aci d- r esi st i ng enamel coat i ng evenl y appl i ed on sur f aces. No f i xt ur e wi l l be accept ed t hat shows cr acks, cr azes, bl i st er s, t hi n spot s, or ot her f l aws. Fi xt ur es shal l be equi pped wi t h appur t enances such as t r aps, f aucet s, st op val ves, and dr ai n f i t t i ngs. Each f i xt ur e and pi ece of equi pment r equi r i ng connect i ons t o t he dr ai nage syst em, except gr ease i nt er cept or s, shal l be equi pped wi t h a t r ap. Br ass expansi on or t oggl e bol t s capped wi t h acor n nut s shal l be pr ovi ded f or suppor t s, and pol i shed chr omi um- pl at ed pi pe, val ves, and f i t t i ngs shal l be pr ovi ded wher e exposed t o v i ew. Fi xt ur es wi t h t he suppl y di schar ge bel ow t he r i m shal l be equi pped wi t h backf l ow pr event er s. I nt er nal par t s of f l ush val ves and f l ushomet er val ves, shower mi xi ng val ves, shower head f ace pl at es, pop- up st opper s of l avat or y wast e dr ai ns, and pop- up st opper s and over f l ow t ees and shoes of bat ht ub wast e dr ai ns shal l be copper al l oy wi t h al l v i s i bl e sur f aces chr ome pl at ed.

2. 4. 1 Aut omat i c Cont r ol s

Fl ushi ng and f aucet syst ems shal l consi st of sol enoi d- act i vat ed val ves wi t h l i ght beam sensor s. Fl ush val ve f or wat er c l oset shal l i ncl ude an

SECTI ON 22 00 00 Page 11 over r i de pushbut t on. Fl ushi ng devi ces shal l be pr ovi ded as descr i bed i n par agr aph FI XTURES AND FI XTURE TRI MMI NGS.

2. 4. 2 Fl ush Val ve Wat er Cl oset s

ASME A112. 19. 2/ CSA B45. 1, whi t e v i t r eous chi na, s i phon j et , el ongat ed bowl , wal l mount ed, wal l out l et . Top of t oi l et seat hei ght above f l oor shal l be 14 t o 15 i nches, except 17 t o 19 i nches f or wheel chai r wat er c l oset s. Pr ovi de wax bowl r i ng i ncl udi ng pl ast i c s l eeve. Pr ovi de whi t e sol i d pl ast i c el ongat ed open- f r ont seat .

Wat er f l ushi ng vol ume of t he wat er c l oset and f l ush val ve combi nat i on shal l not exceed 1. 28 gal l ons per f l ush.

Pr ovi de l ar ge di amet er f l ush val ve i ncl udi ng angl e cont r ol - st op val ve, vacuum br eaker , t ai l pi eces, s l i p nut s, and wal l pl at es; exposed t o v i ew component s shal l be chr omi um- pl at ed or pol i shed st ai nl ess st eel . Fl ush val ves shal l be nonhol d- open t ype. Mount f l ush val ves not l ess t han 11 i nches above t he f i xt ur e. Mount ed hei ght of f l ush val ve shal l not i nt er f er e wi t h t he hand r ai l i n ADA st al l s.

2. 4. 3 Fl ush Val ve Ur i nal s

ASME A112. 19. 2/ CSA B45. 1, whi t e v i t r eous chi na, wal l - mount ed, wal l out l et , s i phon j et , i nt egr al t r ap, and ext ended si de shi el ds. Pr ovi de ur i nal wi t h t he r i m 17 i nches above t he f l oor . Wat er f l ushi ng vol ume of t he ur i nal and f l ush val ve combi nat i on shal l not exceed 0. 5 gal l ons per f l ush.

Provide ASME A112. 6. 1M conceal ed chai r car r i er s wi t h ver t i cal st eel pi pe suppor t s. Pr ovi de l ar ge di amet er f l ush val ve i ncl udi ng angl e cont r ol - st op val ve, vacuum br eaker , t ai l pi eces, s l i p nut s, and wal l pl at es; exposed t o v i ew component s shal l be chr omi um- pl at ed or pol i shed st ai nl ess st eel .

Fl ush val ves shal l be nonhol d- open t ype. Mount f l ush val ves not l ess t han 11 i nches above t he f i xt ur e.

2. 4. 4 Wheel chai r Fl ush Val ve Type Ur i nal s

ASME A112. 19. 2/ CSA B45. 1, whi t e v i t r eous chi na, wal l - mount ed, wal l out l et , bl owout act i on, i nt egr al t r ap, el ongat ed pr oj ect i ng bowl , 20 i nches l ong f r om wal l t o f r ont of f l ar e, and ASME A112. 19. 5 t r i m. Pr ovi de l ar ge di aphr agm ( not l ess t han 2. 625 i nches upper chamber i nsi de di amet er at t he poi nt wher e t he di aphr agm i s seal ed bet ween t he upper and l ower chamber s) , nonhol d- open f l ush val ve of chr ome pl at ed cast br ass conf or mi ng t o ASTM B584, i ncl udi ng vacuum br eaker and angl e ( cont r ol - st op) val ve wi t h back check. The wat er f l ushi ng vol ume of t he f l ush val ve and ur i nal combi nat i on shal l not exceed 0. 5 gal l on per f l ush. Fur ni sh ur i nal manuf act ur er ' s cer t i f i cat i on of conf or mance. Pr ovi de ASME A112. 6. 1M conceal ed chai r car r i er s. Mount ur i nal wi t h f r ont r i m a maxi mum of 17 i nches above f l oor and f l ush val ve handl e a maxi mum of 44 i nches above f l oor f or use by handi capped on wheel chai r .

2. 4. 5 Count er t op Lavat or i es

ASME A112. 19. 2/ CSA B45. 1, whi t e v i t r eous chi na, sel f - r i mmi ng, mi ni mum di mensi ons of 19 i nches wi de by 17 i nches f r ont t o r ear , wi t h suppl y openi ngs f or use wi t h t op mount ed cent er set f aucet s. Fur ni sh t empl at e and mount i ng k i t by l avat or y manuf act ur er . Pr ovi de aer at or wi t h f aucet .

Pr ovi de l avat or y f aucet s and accessor i es meet i ng t he f l ow r at e and pr oduct r equi r ement s of t he par agr aph LAVATORI ES. Mount count er wi t h t he t op sur f ace 34 i nches above f l oor and wi t h 29 i nches mi ni mum cl ear ance f r om

SECTI ON 22 00 00 Page 12 bot t om of t he count er f ace t o f l oor .

2. 4. 6 Ki t chen Si nks

ASME A112. 19. 3/ CSA B45. 4, 20 gage st ai nl ess st eel wi t h i nt egr al mount i ng r i m f or f l ush i nst al l at i on, mi ni mum di mensi ons of 33 i nches wi de by 21 i nches f r ont t o r ear , t wo compar t ment s, wi t h under si des f ul l y sound deadened, wi t h suppl y openi ngs f or use wi t h t op mount ed washer l ess s i nk f aucet s wi t h hose spr ay, and wi t h 3. 5 i nch dr ai n out l et . Pr ovi de aer at or wi t h f aucet . Wat er f l ow r at e shal l not exceed 2. 2 gpm when measur ed at a f l owi ng wat er pr essur e of 60 psi . Pr ovi de st ai nl ess st eel dr ai n out l et s and st ai nl ess st eel cup st r ai ner s. Pr ovi de separ at e 1. 5 i nch P- t r ap and dr ai n pi pi ng t o ver t i cal vent pi pi ng f r om each compar t ment . Pr ovi de t op mount ed washer l ess s i nk f aucet s wi t h hose spr ay. Pr ovi de UL 430 wast e di sposer i n r i ght compar t ment .

2. 4. 7 Ser vi ce Si nks

ASME A112. 19. 2/ CSA B45. 1, ASME A112. 19. 3/ CSA B45. 4 302 st ai nl ess st eel wi t h i nt egr al back and wal l hanger suppor t s, mi ni mum di mensi ons of 22 i nches wi de by 20 i nches f r ont t o r ear , wi t h t wo suppl y openi ngs i n 10 i nch hi gh back. Pr ovi de f l oor suppor t ed wal l out l et cast i r on P- t r ap and st ai nl ess st eel r i m guar ds as r ecommended by ser vi ce s i nk manuf act ur er .

Pr ovi de back mount ed washer l ess ser vi ce s i nk f aucet s wi t h vacuum br eaker and 0. 75 i nch ext er nal hose t hr eads.

2. 4. 8 Dr i nki ng- Wat er Cool er s

AHRI 1010 wi t h mor e t han a s i ngl e t hi ckness of met al bet ween t he pot abl e wat er and t he r ef r i ger ant i n t he heat exchanger , wal l - hung, bubbl er st y l e, ai r - cool ed condensi ng uni t , 4. 75 gph mi ni mum capaci t y, st ai nl ess st eel spl ash r ecept or and basi n, bot t l e f i l l er and st ai nl ess st eel cabi net .

Bubbl er s shal l be cont r ol l ed by push l ever s or push bar s, f r ont mount ed or s i de mount ed near t he f r ont edge of t he cabi net . Bubbl er spout s shal l be mount ed at maxi mum of 36 i nches above f l oor and at f r ont of uni t basi n.

Spout s shal l di r ect wat er f l ow at l east 4 i nches above uni t basi n and t r aj ect or y par al l el or near l y par al l el t o t he f r ont of uni t . Pr ovi de ASME A112. 6. 1M conceal ed st eel pi pe chai r car r i er s. Pr ovi de el ect r i c wat er cool er t hat i s Ener gy St ar l abel ed. Pr ovi de dat a i dent i f y i ng Ener gy St ar l abel f or el ect r i c wat er cool er .

2. 4. 9 Wheel chai r Dr i nki ng Wat er cool er

AHRI 1010, wal l - mount ed bubbl er st y l e wi t h ASME A112. 6. 1M conceal ed chai r car r i er , ai r - cool ed condensi ng uni t , 4. 75 gph mi ni mum capaci t y, st ai nl ess st eel spl ash r ecept or , and al l st ai nl ess st eel cabi net , wi t h 27 i nch mi ni mum knee cl ear ance f r om f r ont bot t om of uni t t o f l oor and 36 i nch maxi mum spout hei ght above f l oor and bot t l e f i l l er . Bubbl er s shal l al so be cont r ol l ed by push l ever s, by push bar s, or t ouch pads one on each si de or one on f r ont and bot h s i des of t he cabi net . Pr ovi de el ect r i c wat er cool er t hat i s Ener gy St ar l abel ed. Pr ovi de dat a i dent i f y i ng Ener gy St ar l abel f or wheel chai r el ect r i c wat er cool er .

2. 4. 10 Emer gency Eyewash and Shower

ANSI / I SEA Z358. 1, f l oor suppor t ed f r ee st andi ng uni t . Pr ovi de del uge shower head, st ay- open bal l val ve oper at ed by pul l r od and r i ng or t r i angul ar handl e. Pr ovi de eyewash and st ay- open bal l val ve oper at ed by f oot t r eadl e or push handl e.

SECTI ON 22 00 00 Page 13

2. 5 DRAINS

2. 5. 1 Fl oor and Shower Dr ai ns

Fl oor and shower dr ai ns shal l consi st of a gal vani zed body, i nt egr al seepage pan, and adj ust abl e per f or at ed or s l ot t ed chr omi um- pl at ed br onze, ni ckel - br onze, or ni ckel - br ass st r ai ner , consi st i ng of gr at e and t hr eaded col l ar . Fl oor dr ai ns shal l be cast i r on except wher e met al l i c wat er pr oof i ng membr ane i s i nst al l ed. Dr ai ns shal l be of doubl e dr ai nage pat t er n f or embeddi ng i n t he f l oor const r uct i on. The seepage pan shal l have weep hol es or channel s f or dr ai nage t o t he dr ai npi pe. The st r ai ner shal l be adj ust abl e t o f l oor t hi ckness. A c l ampi ng devi ce f or at t achi ng f l ashi ng or wat er pr oof i ng membr ane t o t he seepage pan wi t hout damagi ng t he f l ashi ng or wat er pr oof i ng membr ane shal l be pr ovi ded when r equi r ed.

Dr ai ns shal l be pr ovi ded wi t h t hr eaded connect i on. Bet ween t he dr ai n out l et and wast e pi pe, a neopr ene r ubber gasket conf or mi ng t o ASTM C564 may be i nst al l ed, pr ovi ded t hat t he dr ai n i s speci f i cal l y desi gned f or t he r ubber gasket compr essi on t ype j oi nt . Fl oor and shower dr ai ns shal l conf or m t o ASME A112. 6. 3. Pr ovi de dr ai n wi t h t r ap pr i mer connect i on, t r ap pr i mer , and connect i on pi pi ng. Pr i mer shal l meet ASSE 1018.

2. 5. 2 Bat ht ub and Shower Faucet s and Dr ai n Fi t t i ngs

Pr ovi de si ngl e cont r ol pr essur e equal i z i ng bat ht ub and shower f aucet s wi t h body mount ed f r om behi nd t he wal l wi t h t hr eaded connect i ons. Pr ovi de bal l j oi nt sel f - c l eani ng shower heads. Pr ovi de Wat er Sense l abel ed shower head wi t h a maxi mum f l ow r at e of ( 1. 75 gpm) . Pr ovi de dat a i dent i f y i ng Wat er Sense l abel f or shower head. Pr ovi de t ubi ng mount ed f r om behi nd t he wal l bet ween bat ht ub f aucet s and shower heads and bat ht ub di ver t er spout s. Pr ovi de separ at e gl obe val ves or angl e val ves wi t h uni on connect i ons i n each suppl y t o f aucet . Pr ovi de t r i p- l ever pop- up dr ai n f i t t i ngs f or above- t he- f l oor dr ai n i nst al l at i ons. The t op of dr ai n pop- ups, dr ai n out l et s, t ub over f l ow out l et , and; cont r ol handl e f or pop- up dr ai n shal l be chr omi um- pl at ed or pol i shed st ai nl ess st eel .

Li nkage bet ween dr ai n pop- up and pop- up cont r ol handl e at bat ht ub over f l ow out l et shal l be copper al l oy or st ai nl ess st eel . Pr ovi de 1. 5 i nch copper al l oy adj ust abl e t ubi ng wi t h s l i p nut s and gasket s bet ween bat ht ub over f l ow and dr ai n out l et ; chr omi um- pl at ed f i ni sh i s not r equi r ed.

2. 6 TRAPS

Unl ess ot her wi se speci f i ed, t r aps shal l be pl ast i c per ASTM F409 or copper - al l oy adj ust abl e t ube t ype wi t h s l i p j oi nt i nl et and swi vel .

Pr ovi de t r aps wi t h r emovabl e access panel s f or easy c l ean- out at s i nks and l avat or i es. Tubes shal l be copper al l oy wi t h wal l s not l ess t han 0. 032 i nch t hi ck wi t hi n commer ci al t ol er ances, except on t he out si de of bends wher e t he t hi ckness may be r educed sl i ght l y i n manuf act ur e by usual commer ci al met hods. I nl et s shal l have r ubber washer and copper al l oy nut s f or s l i p j oi nt s above t he di schar ge l evel . Swi vel j oi nt s shal l be bel ow t he di schar ge l evel and shal l be of met al - t o- met al or met al - t o- pl ast i c t ype as r equi r ed f or t he appl i cat i on. Nut s shal l have f l at s f or wr ench gr i p. Out l et s shal l have i nt er nal pi pe t hr ead, except t hat when r equi r ed f or t he appl i cat i on, t he out l et s shal l have socket s f or sol der - j oi nt connect i ons. The dept h of t he wat er seal shal l be not l ess t han 2 i nches.

The i nt er i or di amet er shal l be not mor e t han 1/ 8 i nch over or under t he nomi nal s i ze, and i nt er i or sur f aces shal l be r easonabl y smoot h t hr oughout . A copper al l oy " P" t r ap assembl y consi st i ng of an adj ust abl e " P" t r ap and t hr eaded t r ap wal l ni ppl e wi t h cast br ass wal l f l ange shal l

SECTI ON 22 00 00 Page 14 be pr ovi ded f or l avat or i es. The assembl y shal l be a st andar d manuf act ur ed uni t and may have a r ubber - gasket ed swi vel j oi nt .

2. 7 MI SCELLANEOUS PI PI NG I TEMS

2. 7. 1 Escut cheon Pl at es

Pr ovi de one pi ece or spl i t hi nge met al pl at es f or pi pi ng ent er i ng f l oor s, wal l s, and cei l i ngs i n exposed spaces. Pr ovi de chr omi um- pl at ed on copper al l oy pl at es or pol i shed st ai nl ess st eel f i ni sh i n f i ni shed spaces.

Pr ovi de pai nt f i ni sh on pl at es i n unf i ni shed spaces.

2. 7. 2 Pi pe Sl eeves

Pr ovi de wher e pi pi ng passes ent i r el y t hr ough wal l s, cei l i ngs, r oof s, and f l oor s. Sl eeves ar e not r equi r ed wher e dr ai n, wast e, and vent ( DWV) pi pi ng passes t hr ough concr et e f l oor s l abs l ocat ed on gr ade, except wher e penet r at i ng a membr ane wat er pr oof f l oor .

2. 7. 2. 1 Sl eeves i n Masonr y and Concr et e

Pr ovi de st eel pi pe s l eeves or schedul e 40 PVC pl ast i c pi pe sl eeves.

Sl eeves ar e not r equi r ed wher e dr ai n, wast e, and vent ( DWV) pi pi ng passes t hr ough concr et e f l oor s l abs l ocat ed on gr ade. Cor e dr i l l i ng of masonr y and concr et e may be pr ovi ded i n l i eu of pi pe s l eeves when cavi t i es i n t he cor e- dr i l l ed hol e ar e compl et el y gr out ed smoot h.

2. 7. 2. 2 Sl eeves Not i n Masonr y and Concr et e

Pr ovi de 26 gage gal vani zed st eel sheet or PVC pl ast i c pi pe sl eeves.

2. 7. 3 Pi pe Hanger s ( Suppor t s)

Provide MSS SP- 58 Type 1 wi t h adj ust abl e t ype st eel suppor t r ods, except as speci f i ed or i ndi cat ed ot her wi se. At t ach t o st eel j oi st s wi t h Type 19 or 23 cl amps and r et ai ni ng st r aps. At t ach t o St eel W or S beams wi t h Type 21, 28, 29, or 30 cl amps. At t ach t o st eel angl es and ver t i cal web st eel channel s wi t h Type 20 cl amp wi t h beam cl amp channel adapt er . At t ach t o hor i zont al web st eel channel and wood wi t h dr i l l ed hol e on cent er l i ne and doubl e nut and washer . At t ach t o concr et e wi t h Type 18 i nser t or dr i l l ed expansi on anchor . Pr ovi de Type 40 i nsul at i on pr ot ect i on shi el d f or i nsul at ed pi pi ng.

2. 7. 4 Nameplates

Pr ovi de 0. 125 i nch t hi ck mel ami ne l ami nat ed pl ast i c namepl at es, bl ack mat t e f i ni sh wi t h whi t e cent er cor e, f or equi pment , gages, t her momet er s, and val ves; val ves i n suppl i es t o f aucet s wi l l not r equi r e namepl at es.

Accur at el y al i gn l et t er i ng and engr ave mi ni mum of 0. 25 i nch hi gh nor mal bl ock l et t er i ng i nt o t he whi t e cor e. Mi ni mum si ze of namepl at es shal l be

1. 0 by 2. 5 i nches. Key namepl at es t o a char t and schedul e f or each syst em. Fr ame char t s and schedul es under gl ass and pl ace wher e di r ect ed near each syst em. Fur ni sh t wo copi es of each char t and schedul e.

PART 3 EXECUTI ON

3. 1 GENERAL I NSTALLATI ON REQUI REMENTS

Pi pi ng l ocat ed i n ai r pl enums shal l conf or m t o NFPA 90A r equi r ement s.

SECTI ON 22 00 00 Page 15

Pi pi ng l ocat ed i n shaf t s t hat const i t ut e ai r duct s or t hat encl ose ai r duct s shal l be noncombust i bl e i n accor dance wi t h NFPA 90A. I nst al l at i on of pl ast i c pi pe wher e i n compl i ance wi t h NFPA may be i nst al l ed i n accor dance wi t h PPFA Fi r e Man. The pl umbi ng syst em shal l be i nst al l ed compl et e wi t h necessar y f i x t ur es, f i t t i ngs, t r aps, val ves, and accessor i es. Sewer and wat er pi pes shal l be l ai d i n separ at e t r enches, except when ot her wi se shown. I f t r enches ar e c l osed or t he pi pes ar e ot her wi se cover ed bef or e bei ng connect ed t o t he ser vi ce l i nes, t he l ocat i on of t he end of each pl umbi ng ut i l i t y shal l be mar ked wi t h a st ake or ot her accept abl e means. Val ves shal l be i nst al l ed wi t h cont r ol no l ower t han t he val ve body.

3. 1. 1 Wat er Pi pe, Fi t t i ngs, and Connect i ons

3. 1. 1. 1 Utilities

The pi pi ng shal l be ext ended t o f i x t ur es, out l et s, and equi pment . The hot - wat er and col d- wat er pi pi ng syst em shal l be ar r anged and i nst al l ed t o per mi t dr ai ni ng. The suppl y l i ne t o each i t em of equi pment or f i x t ur e, except f aucet s, f l ush val ves, or ot her cont r ol val ves whi ch ar e suppl i ed wi t h i nt egr al st ops, shal l be equi pped wi t h a shut of f val ve t o enabl e i sol at i on of t he i t em f or r epai r and mai nt enance wi t hout i nt er f er i ng wi t h oper at i on of ot her equi pment or f i x t ur es. Suppl y pi pi ng t o f i x t ur es, f aucet s, hydr ant s, shower heads, and f l ushi ng devi ces shal l be anchor ed t o pr event movement .

3. 1. 1. 2 Cut t i ng and Repai r i ng

The wor k shal l be car ef ul l y l ai d out i n advance, and unnecessar y cut t i ng of const r uct i on shal l be avoi ded. Damage t o bui l di ng, pi pi ng, wi r i ng, or equi pment as a r esul t of cut t i ng shal l be r epai r ed by mechani cs ski l l ed i n t he t r ade i nvol ved.

3. 1. 1. 3 Pr ot ect i on of Fi xt ur es, Mat er i al s, and Equi pment

Pi pe openi ngs shal l be c l osed wi t h caps or pl ugs dur i ng i nst al l at i on.

Fi xt ur es and equi pment shal l be t i ght l y cover ed and pr ot ect ed agai nst di r t , wat er , chemi cal s, and mechani cal i nj ur y. Upon compl et i on of t he wor k, t he f i x t ur es, mat er i al s, and equi pment shal l be t hor oughl y c l eaned, adj ust ed, and oper at ed. Saf et y guar ds shal l be pr ovi ded f or exposed r ot at i ng equi pment .

3. 1. 1. 4 Mai ns, Br anches, and Runout s

Pi pi ng shal l be i nst al l ed as i ndi cat ed. Pi pe shal l be accur at el y cut and wor ked i nt o pl ace wi t hout spr i ngi ng or f or c i ng. St r uct ur al por t i ons of t he bui l di ng shal l not be weakened. Abovegr ound pi pi ng shal l r un par al l el wi t h t he l i nes of t he bui l di ng, unl ess ot her wi se i ndi cat ed. Br anch pi pes f r om ser vi ce l i nes may be t aken f r om t op, bot t om, or s i de of mai n, usi ng cr ossover f i t t i ngs r equi r ed by st r uct ur al or i nst al l at i on condi t i ons.

Suppl y pi pes, val ves, and f i t t i ngs shal l be kept a suf f i c i ent di st ance f r om ot her wor k and ot her ser vi ces t o per mi t not l ess t han 1/ 2 i nch bet ween f i ni shed cover i ng on t he di f f er ent ser vi ces. Bar e and i nsul at ed wat er l i nes shal l not bear di r ect l y agai nst bui l di ng st r uct ur al el ement s so as t o t r ansmi t sound t o t he st r uct ur e or t o pr event f l exi bl e movement of t he l i nes.