Attachment_3-_Specs_1.pdf

Initials________________________ Page 2

Section 1: Fire Pump.

1.00 _______ The pump shall be a 1 ½” high pressure four stage centrifugal pump powered by a 23.5 rated Kubota diesel engine with electric start. BB4 pump, Located: Rear center of apparatus. Victaulic connection shall be used on the plumbing from the pump to allow for ease in disconnecting the pump for repairs.

1.01 _______ The pump must deliver the percentage of rated capacity at the pressures listed below:

__103_ GPM at _150__ pounds net pressure ___94_ GPM at _250__ pounds net pressure ___65_ GPM at _350__ pounds net pressure

1.02 _______ The pump shall be capable of taking suction and discharging water with a lift of 10 feet.

1.03 _______ Priming Pump: Shall be a 12 volt electric primer. The primer shall be a 12 VDC rotary vein, semiautomatic priming system with a single action control valve which simultaneously activates the entire system. This primer is self-lubricating so that there is no oil tank to check or refill.

NOTE: 12 volt Hale Primer specified.

There shall be a hand vacuum primer installed also to be used for a secondary or back up priming operation. It shall be connected to the pump through a ¼” turn ball type shut-off valve to prevent the priming system from being pressurized when the pump is attached to a pressurized water source.

1.04 _______ Fire pump engine fuel supply shall be plumbed direct to the chassis fuel supply.

1.05 _______ Engine on pump shall be a 23.5 horsepower, Kubota, liquid cooled industrial diesel engine complete with an alternator. It shall be capable of being powered and throttled from in the chassis cab. There shall be a remote oil drain line.

1.06 _______ The engine muffler shall be mounted inside the compartment where Kubota is and the exit will be high enough to be away from the operators.

1.07 _______ Unique blister resistant mechanical rotary seal to prolong pump end longevity.

1.08 _______ Maintenance free sealed bearing to avoid the need for greasing the pump end in the field.

1.09 _______ Anodized aluminum impellers and pump body which eliminate galvanic corrosion common with bronze impellers.

Section 2: Gated: Inlets, Discharges, & Preconnects.

Initials________________________ Page 3

2.00 _______ All quarter turn valves shall be a fire fighting / repairable brand and be full flow. Each valve shall be plumbed with high pressure hose with stainless steel fittings.

2.01 _______ Gated Discharge Outlets.

2.02 _______ _1_ 1" gated discharge outlet to hose reel as specified at 2.06.

2.03 _______ _1_ 1” refill / recirculate line to booster tank as specified at 3.01

2.04 _______ _1_ 1 ½” gated discharge to the front bumper/brush guard for direct connection. It shall terminate at a male NST fitting with cap and chain. NOTE: The valve shall be angled towards the passenger side, similar to Sublette Wy apparatus.

2.05 _______ _2_ 1 1/2" gated rear discharge outlets for direct connection, each with a Male NH hose connection, with chrome caps and chains. Note: Class A foam shall be piped to the specified discharge.

2.06 _______ A stainless steel manifold system shall be installed for discharges. It shall have an access hole on top with a removable cap. This access shall be used to pour antifreeze into the plumbing and pump. There shall also be a male air fitting in order to blow out any access water from the lines. These features will aid in the attempt to prevent freezing. This does not guarantee that it will prevent freezing.

2.07 _______ Inlets

2.08 _______ _1_ 2 ½” gated tank to pump valve. Note: This is the same as specified in 3.00

2.09 _______ _1_ 2 ½” gated intake valve with a Female, NSTF swivel connection, to include plug and chain.

2.10 _______ _1_ 2 ½” direct tank fill with a NH female swivel with screen, and plug and chain.

2.11 _______ Foam System

2.12 _______ A Class “A” around the pump foam system shall be installed. Will educt concentrate at percentages of 0% to 3.75% at a flow rate from 15 to 125 GPM at 100 PSI. Plumb to on-board foam cell.

Scotty Model: 4171 Location: to all discharges.

2.13 _______ One foam tank with a 10 gallon capacity will be provided and made of polypropylene. It shall have a 4" diameter minimum fill tower, a 1" drain with drain lines that extend below the chassis frame. It shall be marked "CLASS A FOAM". Built integral to booster tank. With built in sight glass included.

2.14 _______ HANNAY HOSE REELS

Initials________________________ Page 4

2.15 _______ _1_ electric rewind booster hose reel with a reel capacity of 150 feet of 1 inch _300_#_ test booster lite hose, Located on the driver’s side on top of front compartment, the front compartment shall be fabricated with a drop-down area so that the reel is not so high.

2.16 _______ Reel rewind button to be located: _on the forward side rail, with a protective guard around the bottom to protect from damage.

2.17 _______ 150 feet of _1_ inch _300_# test booster lite hose to be included with the reel. The hose shall be in 50’ sections for ease of replacement if damaged.

2.18 _______ _1_ set of vertical and horizontal chrome hose roller guides.

Located high on reel.

2.19 _______ Hard suction hose

2.20 _______ _2_ Hard suction hoses are to be provided. Size: 2 ½” x approx. 110” custom length with a 2 ½” RLF x RLM fitting.

Section 3: Booster Tank Valves & Piping

3.00 _______ Two and half inch (2 1/2") ball valve and piping to be connected with flexible hose from tank to pump. Valve to have control on the valve near pump operator.

3.01 _______ 1 " booster tank refill ball valve and piping with flexible hose from pump to tank. Valve to have control on the valve near pump operator.

Section 4: Booster Tank –POLY (LIFETIME WARRANTY)

4.00 _______ Booster tank shall be constructed of ½” Poly sheets. This material shall be a non-corrosive product, black in color, and UV stabilized for maximum protection.

LIFETIME WARRANTY __Make __G3__

4.01 _______ There shall be a 1” FNPT female tank drain located on the rear tank wall, with a removable plug.

4.02 _______ Booster tank shall be of a shape and design to allow for maximum compartmentation.

4.03 _______ All tanks shall have a anti-swirl plate above the sump. The sump shall be recessed into the tank floor and be a minimum of ¼” deep.

4.04 _______ Booster tank shall have a minimum capacity of 350 Gallons.

4.05 _______ The booster tank baffling system shall meet N.F.P.A. standards.

4.06 _______ Booster tank shall have a removable lid.

4.07 _______ The booster tank shall be equipped with a built in water and foam level sight glass facing the rear pump side.

Initials________________________ Page 5

4.08 _______ Water and foam fill towers shall be located at the rear of the

Tank and off to the passenger’s side.

4.09 _______ There shall be (2) poly unistrut channels welded to the top of the tank that runs from that back to the front, they shall be used to secure the aluminum storage basket.

4.10 _______ One foam tank with a 10 gallon capacity will be provided and made of _ polypropylene _. It shall have a 6" diameter minimum fill tower, a 1" drain with drain lines that extend below the chassis frame. It shall be marked "CLASS _A_ FOAM". Note: Built integral to booster tank with built in sight glass.

4.11 _______ Built-in bungs for:

• (3.00) 3” bung for tank to pump plumbing, located behind the driver side compartment wall.

• (3.01) 1-1/2” bung for tank fill/recirculate plumbing.

Section 5: Instrument Panel

5.00 _______ Discharge pressure gauges.

5.01 _______ A gauge for the discharge manifold and (1) on the cab controller, __2__ total.

NOTE: Electric gauge in cab.

Section 6: Apparatus Body & Components

6.00 _______ Complete apparatus body, to be module in construction and

Built separately from chassis and painted to match the chassis.

After complete construction of body it shall be properly fastened to the steel chassis frame with (2) spring loaded u- bolts at the front to allow for flexing along with (2) regular bolts at the rear.

The overall dimensions shall be approx 96” Wide x 115” Long x 43” Tall.

6.01 _______ The apparatus body shall have a rear angle of departure. This will allow better clearance in rough terrain, ditches and ravines.

6.02 _______ Aluminum Bodies shall be constructed with Extrusions for framing purposes. Smooth Sheets shall be used for basic construction, and Aluminum Treadplate shall be used for walkways, high maintenance areas, and for decorative purposes.

The extrusions are to be used in general framing, in both the pump compartment, and the body itself and are to include 3” tubing with a 3/16" radius on the corners. The smooth aluminum sheets shall be 3/16" thick aluminum. Aluminum Treadplate is to be 3/16". Treadplate is to be used in all compartment floors.

These three alloys are to be welded together using the latest Mig Spray Pulse Arc welding system.

6.03 _______ The rear fender wells shall be fabricated from 3/16” smooth aluminum, painted red, with polished extruded aluminum fenderettes. There shall be a circular aluminum inner wheel liner furnished for each side, allowing adequate room for the use of tire chains.

Initials________________________ Page 6

6.04 _______ The front of the apparatus body shall be fabricated with aluminum diamond treadplate gravel shield, to aid in protecting the body from debris that may cause damage to the body.

Section 7: Apparatus Body Compartments

7.00 _______ Body compartments to be fabricated of 3/16" aluminum sheets, aluminum extrusions, and aluminum treadplate. All areas in body construction where dissimilar metals come into contact, shall have a thick rubber pad for separation of each metal. The Apparatus Body shall have a TEN (10) YEAR WARRANTY.

7.01 _______ Compartments to be sweep out design and to be water and dust proof. All compartments shall be made to the maximum practical dimensions for storage capacity.

7.02 _______ Side body compartment doors shall be hinged style, fabricated with .125” smooth aluminum and painted to match chassis color.

• All doors to have keyed “D” ring handles, keyed the same.

• Vertically hinged swing-out doors shall open to the front of the body and equipped with spring style encloser.

• Horizontal hinged lift-up doors shall open from the bottom.

When the door is open (2) gas shocks shall hold the door at 90 degrees to the body.

7.03 _______ All compartments shall be properly vented. The vents shall be constructed of poly and be mounted in a manner that will reduce the amount of dirt and water that may enter the compartment.

The vents shall aid in relieving the pressure when opening and closing the compartment door.

7.04 _______ All exterior compartments shall have an aluminum drip molding installed above the doors where necessary, to prevent water from entering into compartments.

7.05 _______ All shelving shall be fabricated 1/8” smooth aluminum, with a

2” bend up and around the perimeter of the shelves. Each shelf shall be attached to (2) unistrut channels, (1) on each side of the compartment to allow them to be adjustable.

7.06 _______ All compartment floors and shelves shall have black modular floor tiles installed. NOTE: Modular floor tiles are Turtle Tile.

7.07 _______ Left Side Compartments

7.08 _______ Compartments Ahead of Rear Wheels

7.09 _______ High compartment extending in depth to tank with a Single vertically hinged swing door and locking “D” ring handle.

This compartment shall be reinforced on top for a booster reel to be mounted on top. The compartment height may vary to keep the booster reel from exceeding the height of the chassis. Door opening shall be approx 26” W, x 38” H, the height may vary.

7.10 _______ __1__ adjustable shelf.

Initials________________________ Page 7

7.11 _______ Compartments Above Rear Wheels

7.12 _______ Full height compartment extending in depth to tank with a

Single horizontal hinged _lift up_ door and locking “D” ring handle. Door opening shall be approx 38” W x 24” T

7.13 _______ Hose storage compartment, using __3__ G3 hose roll holders.

7.14 _______ Compartment Behind Rear Wheels

7.15 _______ High compartment extending in depth to tank/ pump area with Single vertically hinged _swing-out_ door and locking “D” ring handle. The door opening shall be approximately 25” W x 43” H.

7.16 _______ __1__ adjustable shelf.

7.17 _______ Upper Slotted Hose Storage Compartments

7.18 _______ __1__ Upper hose storage compartment with (2) removable poly hose trays and a center divider running the full length of the compartment, each tray shall be capable of holding 100’ of 1 ½” forestry hose, and be removable, The compartment shall be located above the driver’s side L2 and L3 compartments, and be fabricated from diamond treadplate aluminum enclosed on both sides, front, and on top with a lift-up lid, the rear shall be open, with a web net to secure the (2) poly hose trays. The compartment shall be approx. 12” T x 22” W x 79” L.

7.19 _______ Hose Storage Boxes

7.20 _______ __1__ Hose storage box fabricated from diamond treadplate with a single drop-down hinged door, with (1) finger latch, located on top of L1 compartment. Approx 30 ¾” Wide x 7 ¾” Tall x 21½” Deep.

• The top shall be reinforced to hold the booster hose reel.

• This compartment shall be dry hose storage with NO provisions for a pre connect.

7.21 _______ Right Side Compartments

7.22 _______ Compartments Ahead of Rear Wheels

7.23 _______ High compartment extending in depth to tank with a Single vertically hinged swing door and locking “D” ring handle.

Door opening shall be approx 26” W, x 38” H.

7.24 _______ __2__ adjustable shelves.

7.25 _______ Compartments Above Rear Wheels

7.26 _______ Full height compartment extending in depth to tank with a

Single horizontal hinged, swing up (lift) door and locking “D” ring handle. Door opening shall be approx. 54” W x 16” T.

Initials________________________ Page 8

7.27 _______ Compartments Behind Rear Wheels

7.28 _______ The compartment above the frame rail is framed is to give the ability to mount the portable pump. There shall be louvered panel to allow air flow to the Kubota engine. The panel shall be painted the same color as the body. The rear facing panel shall house the pump controls, and a removable panel above with thumb latches

7.29 _______ R4 low compartment below the frame rail shall be approx.

25” W x 10” T. This compartment shall be well ventilated in order to contain all the spare fluids that the department will need.

7.30 _______ Upper Storage Compartments

7.31 _______ __1__ Upper storage compartment, located above the passenger’s side R1 & R2 compartments, (1) single hinged lift-up door, with (2) locking D ring handles. The door shall face the passenger’s side and be accessible from the ground alongside the apparatus. Approximately 75” L x” 24” T x 22” D.

7.32 _______ Wheel Chock Compartments

7.33 _______ __2__ compartments shall be fabricated to hold (2) light duty wheel chocks in wheel well area, each with a hinged swing door.

Located at the right side wheel well. NOTE: The doors shall be made of smooth aluminum and painted to match chassis.

7.34 _______ Rear Under Body Compartments

7.35 _______ _1_ compartments extending from rear to the front of bed shall be fabricated of 3/16” smooth aluminum. It shall be below the bed and above the frame rail of chassis. It shall have a flip down aluminum door with chevron striping. Approx: 6” Tall x Full length of the body x 34” Wide.

7.36 _______ __1__ poly slide out tray, completely removable with one full length divider to separate hard suction hose from long handled tools. The poly tray has no rollers, it is designed to slide on the compartment floor. There shall be handles on the front face and sides of the tray to completely remove the tray with ease.

NOTE: There shall be 4 dividers that can be adjusted in 6” increments up to 24” on the right side of the full-length divider. The left side shall be for storing (2) custom length hard suction hose. __2__ 2 ½” Hard suction hose included.

7.37 _______ Storage on Top of Tank

7.38 _______ __1__ smooth aluminum storage compartment, fully enclosed, located on top of the tank, with a hinged lift up lid and be sized to fit the maximum space tank around the fill towers and be full length. The fill towers shall be located together at the passenger rear side of the tank.

7.39 _______ Front Hose Storage

Initials________________________ Page 9

7.40 _______ __1__ Hose storage compartment fabricated from diamond treadplate with a hinged lift-up lid, and black bed line finish, large enough to hold up to 30’ of 1 1/2” single jacketed hose for quick connect to the discharge outlet at the front bumper.

The compartment shall be mounted in the center of the front bumper replacement, above the valve as noted in line 2.05.

(Similar to Sublette Wy)

Section 8: Tread bright overlay, & Trim.

8.00 _______ Aluminum tread brite safety trim plate shall be constructed of 6061-T6 1/8" Aluminum, and shall be installed in the following areas.

8.01 _______ Tops of all side compartments

8.02 _______ Floor in the rear pump area.

8.03 _______ Front body panel / gravel shield

Non-slip Running Boards and Rear step.

8.04 _______ All exterior surfaces designated as stepping, standing, and walking areas shall have aluminum non-slip material installed.

The non-slip material shall have a raised serrated surface that will allow moisture to drain out either side. The recessed surface shall be one piece solid material to prevent road spray and debris from entering the top surface from below. The non-slip material shall be applied in the stepping surface of the following areas:

8.05 _______ Apparatus body rear step shall be constructed of non-slip aluminum material.

8.06 _______ There shall be (1) vertical grab rail and (1) horizontal grab rail, located at the rear of the apparatus, located (1 vertical) on the inward side of L3 rear side compartment panel and (1 horizontal) on the top of the spare tire compartment, to aid in accessing the top of the apparatus.

8.07 _______ There shall be (2) large folding steps attached to the side of the spare tire compartment to aid in accessing the fill towers and coffin compartments.

Section 9: Electrical Equipment & Battery System

9.00 _______ Two (2) rear Whelen M6 Series Super LED combination stop/tail lights, one on each side with chrome plated housing.

9.01 _______ Two (2) rear Whelen M6 Series Super LED turn signal with arrow, one on each side with chrome plated housing.

9.02 _______ Two (2) rear Whelen M6 Series Super LED backup light, One on each side with chrome plated housing.

9.03 _______ __2__Chrome flanges for Three (3) lightheads, vertical.

Initials________________________ Page 10

9.04 _______ LED - Clearance lights and reflectors to comply with DOT regulations.

9.05 _______ __2__ LED strip lights in each side compartment and activated by an automatic door switch. They shall be vertically mounted (1) on the inside of the door opening.

NOTE: This does not include dunnage compartments or the rear underbody compartment.

9.06 _______ A flashing red warning light in the cab Marked "DoNot Move

Apparatus When Light Is On" illuminates automatically when the parking brake is not engaged to indicate when passenger or equipment doors are open.

9.07 _______ All electrical equipment to have resetting circuit breakers mounted in a panel box with each circuit labeled.

9.08 _______ Wiring shall be high temperature, copper, multi-strand SXL crosslink coated wire. Wire shall be function coded every 3 inches for ease of maintenance.

9.09 _______ All wiring to be protected with automotive type loom with a temperature rating of -30 degree to +194 degree Fahrenheit.

Grommets shall be used when wiring through body.

9.10 _______ Master battery disconnect shall be a Cole Hersee manually operated, single battery system per NFPA. (This does not apply to chassis factory power). Located on the center console.

9.11 _______ The master electrical module shall be in the console between the front seats and they shall have all master switches, emergency light switches and gauges. Switches shall have a light indicating when on and will be identified by back-lit tags.

9.12 _______ A Kussmaul auto charge 1000 series battery conditioner, with a remote digital display shall be installed. The charger shall be mounted in a clean dry area and will be accessible for service and / or maintenance, the location for the remote digital display shall be determined during the pre-construction meeting.

9.13 _______ A Kussmaul Super Auto Eject, 15-amp automotive disconnect device provided and installed on the 110 volt shoreline connection complete with a yellow weatherproof cover. It shall be activated by the chassis starter switch to disconnect the plug, and completely sealed to prevent contamination from weather and road conditions. Note: Plug shall be on the left side of the apparatus. NOTE: The outlet and bar graph shall be mounted at the wheel well on Driver’s side.

9.14 _______ Class 1 Tank Level Meter

Initials________________________ Page 11

9.15 _______ _2_ Class One ITL Intelli-tank tank level gauges, with (1) water and (1) foam tank level gauge, which utilizes a pressure transducer to provide nine levels of indication, Location: Water and Foam gauge near pump at the rear.

9.16 _______ An additional mini LED water level display and foam level display shall be located in chassis cab, mounted on top of the center console.

9.17 _______ A keyless ignition or ignition key attached to the dash by a chain shall be provided.

9.18 _______ A green "Battery On" light to be provided on the chassis dash.

9.19 _______ A license plate light to be provided on the rear of the apparatus body.

Section 10: Emergency Signal & Lighting Equipment

10.00 _______ __1__ Electronic Siren with microphone: Make: _Whelen_

295SLSA1_ Watts: _100_ located on the center console.

10.01 _______ Electronic Speaker mounted in chassis cab grille or front bumper area, 100 watt.

10.02 _______ Lighting for upper zones A, B, & D. Whelen Freedom IV lightbar, with super LED R/C/B modules (2) red left side corner,

(2) Blue right side corners, (3) Reds on left front, (3) Blues on the right front, (2) alley lights (1) on each end and (2) takedown lights in the front center. It shall be mounted on top of cab roof.

Note: The forward facing white lights shall be deactivated when the vehicle is put in park.

Upper Zones B&D: Two (2) LINZ65, Red and blue with clear lenses, mounted rearward on the upper side of apparatus body

(1) on each side. Blue on the forward side and red on the rearward side.

Upper Zone C: Two (2) LINZ65, Red and blue with clear lenses, mounted on the upper rear of body (1) on each side. Blue on drivers side and red on passenger side.

10.03 _______ Lighting for Lower zones, A.B.C &D: Whelen, Model LINZ65

Series and LINV2 Series, Super LED lights, shall be installed, Lower Zone A: Two (2) LINZ65, Red and blue with clear lenses, mounted on the front of chassis grill. Note: Blue on the drivers side and red on the passenger side, opposite of lightbar.

Lower Zones B&D: Two (2) LINZ65, Red and blue with clear lenses, mounted (1) red forward on the chassis side fender and

(1) blue rearward on the lower body.

Initials________________________ Page 12

Lower Zone C: Two (2) LINV2, Red and blue with clear lenses, mounted on the lower rear of body (1) on each side. The red shall have 6 LED lights, and the white shall have 4 LED lights that work independently as a surface area.

10.04 _______ Six (6) LED ground lights shall be mounted and activated

When the vehicle is placed in park.

• __2__below the cab doors (1) on each side

• __2__below the L-1 and R-1 compartments, (1) per side

• __2__ below the rear tailboard.

10.05 _______ Scene lights for zones, B.C &D: Whelen, Model M6ZC Series, LED scene lights, with inner optic to direct the light downward shall be installed, Upper Zone B: Two (2) M6ZC, mounted (1) forward and (1) rearward on the upper outer corners of the apparatus body.

Upper Zone C: Two (2) M6ZC, mounted on the upper rear outer corners of the apparatus body, (1) on each side.

Upper Zone D: Two (2) M6ZC, mounted (1) forward and (1) rearward on the upper outer corners of the apparatus body.

Note: Each zone shall be activated by a separate lighted Switch located in the chassis cab. The switches shall be Labeled RIGHT SCENE, REAR SCENE & LEFT SCENE.

10.06 _______ __1__LED work light, mounted on the rear of tank to illuminate pump area, controlled from rear of apparatus.

10.07 _______ A 12 volt solid state backup alarm with a minimum rating of 97 decibels to be installed.

Section 11: Painting, Printing, Decorating, Lettering, & Signs.

11.00 _______ The body subframe shall be undercoated with heavy duty automotive type undercoating before the rubber backing and the compartment are bolted on. After the body has been bolted onto the subframe and all final items have been installed the body shall be undercoated in the same manner.

11.01 _______ The interior of the body compartments, with the exception of the floors, shall be painted with a light gray bed liner.

11.02 _______ The compartment inner door panels shall be light gray bed liner to match interior of the body compartments.

11.03 _______ All other metal surfaces shall be thoroughly cleaned with grease cutting agent and metal phosphate before primer is applied. All flanges on body which cannot be painted after assembly shall be primed and painted before assembly.

Initials________________________ Page 13

11.04 _______ Paint Process

• Apparatus body washed with grease cutting solvents prior to sanding

• Minor imperfections on the body filled, and entire body is sanded

• Body washed again to remove contaminants.

• 1st coat- self etching primer for maximum paint adhesion to the metal body

• 2nd and 3rdcoat- acrylic urethane primer surface which is hand sanded with 600 grit sandpaper to ensure maximum paint gloss.

• 3 coats of Acrylic Urethane two-component color.

• Painted finish is then properly cured and insures a 5-year paint warranty.

11.05 _______ Apparatus body to be painted red, to match the chassis paint.

Note: (1) – 2oz bottle of touch-up paint shall be supplied with the completed truck.

11.06 _______ A 1” x 4” x 1” black reflective stripe provided on both sides of chassis and body. Note: Straight with an upward angle on L1 and R1 compartment doors, then back to straight to the back of the apparatus.

11.07 _______ Chevron reflective striping shall be installed on vertical rear surface above tailboard at a 45 degree angle. Color: black/red.

11.08 _______ Lettering shall be TBD

(Not to exceed 50 - 4” letters): Note: The department will send digital files for door lettering.

11.09 _______ A permanent plate shall be installed in the driver's compartment specifying the maximum number of personnel the vehicle is designed to carry per NFPA standards. It should be located in an area visible to the driver.

11.10 _______ An accident prevention sign stating "DANGER", personnel must be seated and seat belts must be fastened while vehicle is in motion, or "DEATH OR SERIOUS INJURY MAY RESULT" shall be provided. It shall be visible from each seating position.

11.11 _______ An accident prevention sign stating "DANGER", do not ride on rear step while vehicle is in motion. "DEATH OR SERIOUS INJURY MAY RESULT" shall be provided.

It shall be visible from the rear step area of the vehicle.

11.12 _______ A permanent fluid plate, specifying the quantity and type of the following fluids that may be used in the apparatus for normal maintenance. Located in the chassis cab.

• ENGINE OIL

• ENGINE COOLANT

• CHASSIS TRANSMISSION FLUID

• POWER STEERING FLUID

• DRIVE AXLE LUBRICATION FLUID

• PAINT COLOR NUMBER

Initials________________________ Page 14

Section 12: Chassis Modification & Miscellaneous:

12.00 _______ There shall be a custom designed poly console located between the front seats, it shall be designed to hold, if applicable, the items listed below.

• All vehicle warning light switches, terminations, and relays

• Master power switch termination

• Apparatus fuses and circuit breakers

• Siren controller

• Scene light control switches

• 6” Map box located on the back of the console

• Two (2) 12-volt power ports

• Two (2) cup holders on the front of the console

• One (1) power strip receptacle mounted on the back of the Console powered by the shoreline

• Mini Water and Foam level gauges

12.01 _______ _2_ rear tow eyes, mounted direct to chassis frame rail.

12.02 _______ Two 2” receivers, _1_ to be located on the front with winch power connection, and _1_ at the rear with 7-pin wiring harness for quick connect for a trailer at the rear of the apparatus.

12.03 _______ There shall be a Warn portable winch with cradle. It should include a remote cable with a 12’ lead, fairlead rollers, and 90’ of wire rope. It shall be wired directly to the12 volt power system.

12.04 _______ There shall be mud flaps installed behind the rear tires.

12.05 _______ Chassis is to be painted 2-toned black over red. The chassis will be ordered black and the lower portion shall be painted to match the body Red, this will not include door jams under the hood or any interior. NOTE: Paint break shall match provided drawing.

12.06 _______ Chassis Wheels and Tires Conversion,

• __4__ 20” x 11” one-piece steel powder coated wheels, DOT approved and rated.

• __4__ – 41” diameter, 335 x 80 R - 20 on/off highway, 7300 lb capacity each

• __2__Custom Designed, over-sized, carbon fiber mounted fender flares

• 3.0” suspension lift on the front and rear

• __1__Radiator Skid Plate

• __1__ Transmission skid plate

• __1__ Transfer case skid plate

• __1__ set of customized running boards

• __1__ Black powder coated customized grill / brush guard.

There shall be space for mounting of up to 30’ of 1 1/2” single jacketed hose for quick connect to the discharge outlet at the front bumper.

12.07 _______ Add (1) pull out drop down step on the lower rear center of the apparatus. Located under the rear tail board.

Initials________________________ Page 15

12.08 _______ Add a nylon webbing cover to contain the fire hose in the upper left hose storage compartments. (LENS)

12.09 _______ Add (2) Handelok brackets to the upper driver side compartment to hold the hose ends while in the upper hose storage compartments.