ATTACHMENT 3 - MV Raccoon Technical Interspec.pdf

Where legislation does not explicitly restrict or limit the use of lead containing coatings it is the responsibility of the client to inform International Paint in writing of their specific requirements

Technical Specification

USACE Sausalito 2020 Drydock

M/V Raccoon

California- San Francisco, United States

06-Oct-2020

USSG01-3C76-8Q6C/2

Stan R Gag stan.gag@akzonobel.com

Cell Ph (707) 344-6644

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

M/V Raccoon

Attachment 3/Technical Exhibit 3 – Raccoon paint spec

Main Schemes Area Description Area (ft²)

1. UWH An Interspeed 6400NA TBT free antifouling scheme 3,789

2. Freeboard An Intershield 300V abrasion resistant epoxy with Interthane 990HS. 2,500

3. Weathering Decks Interbond 998 epoxy anti-corrosive system for long lasting protection and added abrasion resistance. 2,500

4. Potable Water Tanks Interseal 670HS for touchup of damaged areas 250

5. Crane and Superstructure Repairs An Intershield 300V abrasion resistant epoxy with Interthane 990HS. 2,100

Thinners

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

1. UWH [3,789 ft²]

An Interspeed 6400NA TBT free antifouling scheme

Surface Preparations High pressure fresh water washed at pressures between 205 and 275 bar (3,000 to 4,000 psi) Sweep blasting

Product Sales Code Colour Coats % Loss factor

WFT

(mil)

DFT

(mil)

PSR

(ft²/G)

Pot Life 20°C

Touch Dry

20°C

Hard Dry

20°C

Overcoating 20°C

Before Flooding

20°C

Thinner Cleaner Volum e

(G)

Volume Solids

Dry To

Walk On

20°C

Min Max

Intershield 300V

ENA310/

ENA313

Bronze FC 30 7.9 5 143.83 3hrs 3.5hrs 6.5hrs 8hrs 14days GTA220 GTA415, GTA822

26.3 63

Intershield 300V

ENA311/

ENA313

Aluminium FC 30 7.9 5 143.83 3hrs 3.5hrs 6.5hrs GTA220 GTA415, GTA822

26.3 63

Interspeed

6400NA

BQA679 Black FC 30 8.3 5 136.91 4hrs 9.5hrs GTA007 GTA007 27.7 60

Interspeed

6400NA

BQA674 Red FC 30 8.3 5 136.91 4hrs 9.5hrs GTA007 GTA007 27.7 60

32.4 20 108.0

Scheme notes

Sweep blast to be performed per SSPC SP-14 / NACE #8 Industrial Blast Cleaning.

*Interspeed 6400NA Black to be applied over thumb print tacky Intershield 300V Aluminum*

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

2. Freeboard [2,500 ft²]

An Intershield 300V abrasion resistant epoxy with Interthane 990HS.

Surface Preparations High pressure fresh water washed at pressures between 205 and 275 bar (3,000 to 4,000 psi) Sweep blasting

Product Sales Code Colour Coats % Loss factor

WFT

(mil)

DFT

(mil)

PSR

(ft²/G)

Pot Life 20°C

Touch Dry

20°C

Hard Dry

20°C

Overcoating 20°C

Before Flooding

20°C

Thinner Cleaner Volume (G)

Volume Solids

Dry To

Walk On

20°C

Min Max

Intershield 300V

ENA310/ENA313 Bronze 30%

TU

30 7.9 5 143.83 3hrs 3.5hrs 6.5hrs 8hrs 6mths GTA220 GTA415, GTA822

5.2 63

Intershield 300V

ENA311/ENA313 Aluminium 30%

TU

30 7.9 5 143.83 3hrs 3.5hrs 6.5hrs 8hrs 3days GTA220 GTA415, GTA822

5.2 63

Interthane

990HS

99002/990B Black FC 30 4.4 3 258.74 8hrs ext. GTA056 GTA056 9.7 68

Interthane

990HS

99010/990B White 10%

TU

30 4.4 3 258.74 8hrs ext. GTA056 GTA056 1.0 68

24.6 16 21.1

Scheme notes

Sweep blast to be performed per SSPC SP-14 / NACE #8 Industrial Blast Cleaning.

Interthane 990HS white to be used for vessel markings

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

3. Weathering Decks [2,500 ft²]

Interbond 998 epoxy anti-corrosive system for long lasting protection and added abrasion resistance.

Surface Preparations High pressure fresh water washed at pressures between 205 and 275 bar (3,000 to 4,000 psi) Blast to Sa2 ISO 8501-1 or SSPC SP6.

Waterjetting to SSPC-SP12 or NACE WJ-2

Product Sales Code Colour Coats % Loss factor

WFT

(mil)

DFT

(mil)

PSR

(ft²/G)

Pot Life 20°C

Touch Dry

20°C

Hard Dry

20°C

Overcoating 20°C

Before Flooding

20°C

Thinner Cleaner Volume (G)

Volume Solids

Dry To

Walk On

20°C

Min Max

Interbond

KRA920/KRA923 Off-White FC 30 5.6 5 205.36 9hrs 28days GTA822, GTA220

12.2 90

Interbond

KRA924/KRA923 Terracotta Red

FC 30 5.6 5 205.36 9hrs 28days GTA822, GTA220

12.2 90

Interbond

KRA924/KRA923 Terracotta Red

FC 50 5.6 5 146.68 GTA822,

GTA220

17.0 90

Interthane

990HS

PCB134/990B Yellow 25%

TU

30 4.4 3 258.74 8hrs ext. GTA056 GTA056 2.4 68

21.2 18 43.8

Scheme notes

*If waterjetting option is used; contractor to ensure sufficient profile is present on bare steel* Aluminum oxide grit to be broadcast into wet Interbond 998 Terracotta Red and seal coated with Interbond 998 Terracota Red. Non-skid grit to be approved by Owner.

** Interthane 990HS B134 yellow to be used for deck markings and cleats

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

4. Potable Water Tanks [250 ft²]

Interseal 670HS for touchup of damaged areas

Surface Preparations Ensure the area is clean and dry prior to application.

Power tooling to SSPC SP11. Power tool cleaning to remove tightly adhering material which is visibly free from all rust, mill scale and old coatings, and has a surface profile.

Product Sales Code Colour Coats % Loss factor

WFT

(mil)

DFT

(mil)

PSR

(ft²/G)

Pot Life 20°C

Touch Dry

20°C

Hard Dry

20°C

Overcoating 20°C

Before Flooding

20°C

Thinner Cleaner Volume (G)

Volume Solids

Dry To

Walk On

20°C

Min Max

Interseal

670HS

EGA093/EGA247 Buff 75%

TU

30 6.1 5 187.02 22hrs ext. GTA220 GTA822 1.0 82

Interseal

670HS

EGA010/EGA247 White 75%

TU

30 6.1 5 187.02 22hrs ext. GTA220 GTA822 1.0 82

12.2 10 2.0

Scheme notes

White or buff colors only for NSF approved systems

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

5. Crane and Superstructure Repairs [2,100 ft²]

An Intershield 300V abrasion resistant epoxy with Interthane 990HS.

Surface Preparations High pressure fresh water washed at pressures between 205 and 275 bar (3,000 to 4,000 psi) Degrease to SSPC SP1 solvent cleaning.

Power tool areas to St3 ISO 8501-1 or SSPC-SP3.

Ensure the area is clean and dry prior to application.

Product Sales Code Colour Coats % Loss factor

WFT

(mil)

DFT

(mil)

PSR

(ft²/G)

Pot Life 20°C

Touch Dry

20°C

Hard Dry

20°C

Overcoating 20°C

Before Flooding

20°C

Thinner Cleaner Volume (G)

Volume Solids

Dry To

Walk On

20°C

Min Max

Intershield 300V

ENA310/ENA313 Bronze 30%

TU

30 6.3 4 179.69 3hrs 3.5hrs 6.5hrs 8hrs 6mths GTA220 GTA415, GTA822

3.5 63

Intershield 300V

ENA311/ENA313 Aluminium 30%

TU

30 6.3 4 179.69 3hrs 3.5hrs 6.5hrs 8hrs 7days GTA220 GTA415, GTA822

3.5 63

Intertuf 262 KHA300/

KHA062

Off White 30%

TU

30 4.1 3 277.48 6hrs 8hrs 4days GTA220 GTA220, GTA822

2.3 73

Interthane

990HS

99011/990B Base Light 35%

TU

30 4.4 3 258.74 8hrs ext. GTA056 GTA056 2.9 68

21.1 14 12.2

Scheme notes

Feather surrounding area to a sound edge. Overlap onto existing sound coatings by 2-3 cm. Ensure all surfaces are clean, dry and free of contamination prior to application of each coat of the specified system.

Interthane 990HS to be tinted to shade 71123 Ivory to match existing finish

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

Product List Product Paint Type Colour Sales Code VOC

(lb/G) Volume Solids

Volume

(G)

Interbond 998 Surface Tolerant Epoxy Off-White KRA920/KRA923 0.8 90 12.2

Interbond 998 Surface Tolerant Epoxy Terracotta Red KRA924/KRA923 0.8 90 29.2

Interseal 670HS Surface Tolerant Epoxy White EGA010/EGA247 2 82 1.0

Interseal 670HS Surface Tolerant Epoxy Buff EGA093/EGA247 2 82 1.0

Intershield 300V Abrasion Resistant Aluminium Pure Epoxy

Bronze ENA310/ENA313 2.7 63 35.0

Intershield 300V Abrasion Resistant Aluminium Pure Epoxy

Aluminium ENA311/ENA313 2.7 63 35.0

Interspeed 6400NA TBT Free CDP Antifouling Red BQA674 3.2 60 30.0

Interspeed 6400NA TBT Free CDP Antifouling Black BQA679 3.2 60 30.0

Interthane 990HS Low VOC Polyurethane Finish Black 99002/990B 2.7 68 10.0

Interthane 990HS Low VOC Polyurethane Finish White 99010/990B 2.7 68 5.0

Interthane 990HS Low VOC Polyurethane Finish Base Light 99011/990B 2.7 68 2.9

Interthane 990HS Low VOC Polyurethane Finish Yellow PCB134/990B 2.7 68 2.4

Intertuf 262 Epoxy Anticorrosive Off White KHA300/KHA062 2.4 73 2.3

Total 196.0

Thinners Product Paint Type Colour Sales Code VOC

(lb/G) Volume Solids

Volume

(G)

International Thinners/ Cleaners/ Miscellaneous GTA007 ― ― 20.0

International Thinners/ Cleaners/ Miscellaneous GTA056 ― ― 10.0

International Thinners/ Cleaners/ Miscellaneous GTA220 ― ― 20.0

Total 50.0

Total volume (G): 246.0

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

Terms and Conditions

This confidential document is for the use of the above named client and its contents should not be reproduced or transmitted without prior written permission from International Paint. The information is given in good faith and attention to the following statement :

The information given in this report is not intended to be exhaustive and any person using any products for any purpose other than that specifically recommended in this report without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. Any warranty, if given, or specific Terms & Conditions of Sale are contained in International Paints Terms and Conditions of Sale, a copy of which can be obtained on request. Whilst we endeavour to ensure that all advice we give about the product (whether in this report or otherwise) is correct we have no control over either the quality or condition of the substrate or the many factors affecting the use and application of this product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever for howsoever arising for the performance of our products or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of the use of the product. The information contained in this report is liable to modification from time to time in the light of experience and our policy of continuous product development.

It is the user's responsibility to check that upto date product data sheets are obtained prior to using the products and that local environmental controls that may be in force are observed when using any of our products.

Health & Safety Products referred to in this report are intended for use only by professional applicators in industrial situations in accordance with the advice given on our Technical Datasheetst, the Material Safety Data Sheet and the container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environment standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult International Paint for further advice.

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

Terms and Conditions of Sale

SCOPE: As used herein, “AkzoNobel” means the AkzoNobel entity identified above; “Buyer” means the purchaser of Products from AkzoNobel and “Products” means any and all goods sold by 1.

AkzoNobel to Buyer. Unless a detailed product sales agreement is in place between AkzoNobel and Buyer covering the sale of the Products, all Products sold or otherwise provided by AkzoNobel are sold or provided exclusively on the basis of these Terms and Conditions of Sale. No differing or supplemental terms or conditions shall be applicable unless expressly agreed to by AkzoNobel in writing.

OFFER / ACCEPTANCE: A quotation from AkzoNobel does not constitute an offer but an invitation to Buyer to make an offer. In all cases Buyer’s offer shall be deemed based on these Terms and 2.

Conditions of Sale. An agreement comes into effect only when AkzoNobel accepts Buyer’s offer.

DELIVERY / TRANSFER OF RISK: Delivery terms shall be interpreted in accordance with the latest INCOTERMS valid at the date the order is accepted. Unless otherwise agreed to by AkzoNobel in 3.

writing the delivery term is EXW and risk of loss in the Products will transfer to Buyer upon tender of the Products to Buyer or the carrier at AkzoNobel’s shipping facility. Buyer shall be responsible for all storage and other costs relating to Buyer’s failure to accept delivery pursuant hereto. The method and agency of transportation, unless otherwise agreed to in writing, may be selected by AkzoNobel and AkzoNobel reserves the right to ship collect. AkzoNobel’s receipt from the carrier shall be conclusive evidence of delivery and the amount delivered. Shipping and delivery dates are approximate and are given by AkzoNobel in good faith, but are not guaranteed unless otherwise specifically agreed in writing.

QUANTITY VARIATIONS: Buyer will pay for the quantity delivered and may not reject any delivery of Product on the grounds of variation of quantity where such variation is not more than 10% of the 4.

quantity ordered.

RETURNS: No Products may be returned for any reason without AkzoNobel’s written authorization. Tinted product and special orders may not be returned at any time. If AkzoNobel authorizes a 5.

return, Buyer must return the Products in clean, resalable condition. If returned for reasons other than AkzoNobel’s error in filling Buyer’s order, the Buyer will receive a credit in the amount of the billed price of the Products returned less 20% for handling, if returned within 90 days of the invoice date. Amount of credit for materials returned after 90 days is subject to negotiation. Products returned to AkzoNobel are to be shipped by the Buyer DDP AkzoNobel’s designated warehouse.

PRICE AND PAYMENT: Unless otherwise agreed by the Parties, the price for the Products will be the price quoted by AkzoNobel. All prices quoted by AkzoNobel are exclusive of value added tax and 6.

any other tax that may apply in respect of the Products. AkzoNobel will issue invoices to Buyer for all Products sold to Buyer. Buyer shall pay these invoices within thirty (30) days from the invoice date in the currency indicated on the invoice at the address of AkzoNobel indicated on the invoice. Any amounts not paid in accordance with invoiced terms shall bear interest at a rate of one and one-half percent (1.5%) per month or, if less, the highest rate permitted by applicable law. Buyer may not withhold payment of any amount due to AkzoNobel because of any set-off, counter-claim, abatement or similar deduction. Upon demand Buyer will immediately reimburse AkzoNobel for any and all costs including fees for collection agencies and attorneys incurred or expended by AkzoNobel to collect any amounts due from Buyer.

RETENTION OF TITLE: AkzoNobel retains a security interest in all Products delivered to Buyer to secure payment in full of all amounts due to AkzoNobel and Buyer shall, upon AkzoNobel’s request, 7.

execute such documentation as AkzoNobel deems necessary to perfect or maintain its security interest in the Products. Title to the Products passes to Buyer (subject to AkzoNobel’s security interest) at the time risk of loss passes to Buyer. Buyer may sell the Products in the ordinary course of its business, but may not pledge, mortgage or otherwise encumber the Products prior to payment in full of the purchase price.

WARRANTY / BUYER’S RIGHTS: AkzoNobel warrants to Buyer that at the time of transfer of risk of loss the Products conform to AkzoNobel’s standard Product specifications or such other 8.

specifications as AkzoNobel and Buyer have expressly agreed to in writing (the “ Specifications”). THIS WARRANTY IS THE SOLE WARRANTY GIVEN BY AKZONOBEL. AKZONOBEL MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, WITH RESPECT TO THE PRODUCTS, THE APPLICATION OR USE THEREOF, OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, EACH OF WHICH IS SPECIFICALLY DISCLAIMED. In the event Products do not comply with the foregoing warranty, AkzoNobel will, at its option, repair or replace such Products or refund the Price of the Products and, having done so, will have no further liability. Buyer must notify AkzoNobel of any claim Products do not comply with the foregoing warranty within seven (7) days after Buyer becomes aware of such claim but in no event later than thirty (30) days after delivery of the Product to Buyer.

Buyer’s failure to notify AkzoNobel of any such claim within the time set out in the preceding sentence will constitute a waiver by Buyer of such claim. AkzoNobel makes no warranty of any kind with

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020

Terms and Conditions of Sale respect to any services provided to Buyer and shall have no liability with respect to such services. Seller’s Warranty does not apply to any Products identified as obsolete, substandard, or past the recommended shelf-life, which are sold “AS IS, WHERE IS.”

LIMITATION OF LIABILTY: AkzoNobel will not be liable for any loss or damage caused by Buyer’s failure to exercise effective quality control or the failure to store, use or otherwise handle the Products 9.

as advised or in accordance with instructions provided by AkzoNobel or industry standards. AKZONOBEL WILL NOT BE LIABLE TO BUYER, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), BREACH OF STATUTORY DUTY OR OTHERWISE FOR ANY LOSS OF PROFIT, LOSS OF BUSINESS, DIMINUTION IN VALUE, OR DEPLETION OF GOODWILL OR ANY INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL LOSS OR DAMAGE. AKZONOBEL’S AGGREGATE LIABILITY TO BUYER IN RESPECT OF ALL LOSSES ARISING UNDER OR IN CONNECTION WITH THE SUPPLY OF PRODUCTS WILL IN NO WAY EXCEED THE PRICE OF THE PRODUCTS PURCHASED, OR $1,000,000, WHICHEVER IS LOWER. Nothing in this section will limit or exclude AkzoNobel’s liability for any matter in respect of which it is unlawful for AkzoNobel to exclude or restrict its liability.

HEALTH & SAFETY OF WORKERS: Buyer expressly assumes all liability resulting from, or in any way connected with, the possession, handling and/or use by its employees, agents, or clients of the 10.

Products. Buyer hereby agrees to indemnify, defend and hold AkzoNobel and its affiliates harmless fro m all claims, judgments, losses or expenses and any costs (including, but not limited to court costs and attorney’s fees) in any way related to Buyer’s or its subcontractor’s failure to comply with any of the foregoing.

FORCE MAJEURE: AkzoNobel will not be liable in any respect for failure to perform its obligations if hindered or prevented, directly or indirectly by war (declared or undeclared), national emergency, 11.

inadequate transportation facilities, machinery or equipment failure, AkzoNobel’s inability to secure materials, supplies, fuel or power for the manufacture of Product on terms and conditions that are acceptable to AkzoNobel, fire, flood, windstorm or other act of God, strike, lockout or other labour dispute, order or act of any government, whether foreign, national or local, whether valid or invalid, or any other cause of like or different kind beyond the reasonable control of AkzoNobel (each a “Force Majeure”). AkzoNobel shall have no obligation to procure any Products from other sources and may allocate its available supply of Products among the members of the AkzoNobel Group (including itself) and their customers, buyers, distributors and resellers on whatever basis AkzoNobel may deem fair and practical. In the event that the duration of a Force Majeure exceeds thirty (30) days or is reasonably expected to exceed 30 days, AkzoNobel is entitled to withdraw from any obligation it may have to supply the Products to Buyer without the Buyer having any right to compensation.

EXPORT CONTROL: Buyer will not sell, export, re-export, license, transmit, divert or otherwise transfer, directly or indirectly, any Product or any information or technology related to the Product 12.

except in accordance with applicable laws and regulations, including without limitation applicable UN, US and EU export control laws and regulations and the laws and regulations of the country where Buyer is resident. Buyer acknowledges that it will (i) take all steps necessary to comply with the above laws and regulations, including obtaining export and other licenses if necessary and (ii) not take any actions that would cause AkzoNobel to be in violation of the above laws.

TERMINATION: An agreement with Buyer to deliver Products on the basis of these Terms and Conditions will not oblige AkzoNobel for the future to take further orders. AkzoNobel will at all times be 13.

entitled to end the relationship. Such termination will never entitle Buyer to compensation.

MARITIME LIEN: This agreement is subject to the general maritime laws of the United States of America. Such laws shall also govern, without limitation, all issues concerning the enforcement, 14.

application and status of maritime liens. No attempt to waive, negate or nullify the supplier’s maritime l ien against the vessel or waive the vessel’s ultimate liability for the costs of products supplied is acceptable. Any attempt to do so, particularly by endorsing delivery receipts, will be of no effect or validity. Please inform the Owners (if different from you) and the vessel’s Master, accordingly.

LAW AND DISPUTE RESOLUTION: To the extent this agreement is not subject to the general maritime laws of the United States of America, these Terms and Conditions and all disputes between 15.

AkzoNobel and Buyer are governed by the laws of the State of Texas, excluding the United Nations Convention of Contracts for the International Sale of Goods and any choice of law rules that direct the application of the law of any other jurisdiction. Any dispute between AkzoNobel and Buyer that the parties are unable to resolve by agreement will be resolved exclusively in the courts havin g jurisdiction over the subject matter of the dispute located in Houston, Texas. Each party consents and agrees to the jurisdiction and venue of such courts.

NOTICE: All notices, request, demands or other communications to or upon the AkzoNobel shall be made in writing to the following address: 6001 Antoine Drive, Houston, Texas, Attn: Commercial 16.

Department.

Interspec

Marine Coatings Unless otherwise agreed in writing, all products supplied and technical advice given by us are subject to our standard terms and conditions of sale.

Please note that a surcharge may be applied to the prices listed, in which case this will be notified to you by your International Paint representative. In the event that supplies are made and technical advice is given by one of our associated companies then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of which is available upon request

USSG01-3C76-8Q6C/2

06-Oct-2020