Attachment 3 - Group BBQ offloading instructions.pdf

(530) 365-6106 Fax (530) 365-5129

2270 Barney Rd.• Anderson, CA 96007www.outdoorcreations.com

Product Handling Methods

Picnic Tables:

Benches:

If you have any questions or concerns regarding correct product handling methods, please contact your sales representative. Outdoor Creations, Inc. is not responsible for product damage associated with incorrect handling.

In the event the equipment and/or site conditions do not meet Outdoor Creations Inc. criteria, causing a delay in offloading, the customer will be charged for stand-by time until the delay is corrected.

NOTE: Nylon slings may be used around table top to maneuver the table (call for instructions).

Preferred Method Acceptable Method Unacceptable Method!!

DO NOT ATTEMPT TO

LIFT OR MOVE UNDER SEATS!

Forklift Fork

Padding

Lift bench with well padded forklift forks (carpet, cardboard, wood, etc) from front or back staying as centered as possible for good load balance. Keep forks spread as far as possible for latteral balance.

Keep bench absolutely level to the ground when lifting or setting to eliminate risk of chipping leg bottoms.

Palletized Items For ALL items delivered on pallets, the item must be kept on the pallet until ready to set into final placement. Using your offloading equipment, set pallet where the item will ultimately be placed.

Lift the item with offloading equipment, remove pallet, and set item down. DO NOT lift item with equipment and travel to location of placement. This will damage the item and Outdoor Creations Inc. will NOT be liable for damage associated with improper product handling.

2270 Barney Rd.• Anderson, CA 96007www.outdoorcreations.com

Lift center hotplates to reveal hook notches cut into vertical grill frame below hotplates.

See notch location, figure 1 and 2.

Attach hook equiped ends of suitable chain, cable, strap, etc to two opposing chain notches on grill frame.

Use suitable equipment (ie. forklift, crane, front loader, etc) to lift barbecue.

Chain hook notches, use from opposing corners as shown in figure 1 to balance weight.

Hot plate doors in open position (side view)

Family Barbecues & Hot Coal Receptacles:

Group Barbecues:

IMPORTANT NOTICE:

Forklift Fork Padding

Lift grills to reveal chain hook notches located on

(2) opposing corners of lower grill.

See figure 1 and 2.

Figure 1

Figure 1 Figure 2

Figure 3

Figure 2 (Lower Grill)

Hot Coal Receptacle

Chain notches cut to allow chain hooks to grasp lower grill for lifting

Lift points on a Hot Coal Receptacle are the opposing corners of the grill

Attach hook equipped ends of suitable chain, cable, strap, etc to two opposing chain notches on lower grill.

Use suitable equipment

(ie. Forklift, crane, front loader, etc) to lift barbecue.

*When removing barbecue from pallet for placement, place palletized item in final position to minimize travel time while hanging.

Figure 3

For adjustable grill group barbecues (#3001AG), forklift forks can be placed under arch and lifted off of pallet.

The grills that come with barbecues and firepits have a coating on them. Before the first use, it is important to heat the grill up to a proper temperature to burn the coating off. Once the coating has been burned off, lightly coat the surface of the grill with a vegetable oil. The grill can be maintained by periodically repeating the “seasoning” process of heating the grill and lightly coating with vegetable oil.

mjohnston Highlight

2270 Barney Rd.• Anderson, CA 96007www.outdoorcreations.com

Door

Waste Receptacles:

Firepits:

Waste Receptacles (Model# 507/508):

Lift lid from waste receptacle to reveal (4) cast in threaded inserts containing bag retaining hooks. Remove liner if so equipped.

Remove two opposing bolts and attach chain or other lifting device with ½” X 1 ½” coarse thread bolts.

Trash receptacle unit CANNOT be lifted by top.

DO NOT TRANSPORT UNIT IN THIS MANNER AS DAMAGE COULD OCCUR.

Pre-place unit in final location by pallet. Insert padded forklift fork through door, lift off of pallet, remove pallet and set receptacle in place.

Threaded inserts, remove opposing bolts

Use suitable equipment

(ie. Forklift, crane, front loader, etc) to lift waste receptacle.

*When removing waste receptacle from pallet for placement, place palletized item in final position to minimize travel time while hanging.

Lifting chains need to attach vertically so that weight is supported at as close to 90 degree angle from lifting point as possible.

ONLY LIFT FROM OUTER MOST POINT OF GRILL AS SHOWN.

Allowing lift point to occur at inside of grill will damage grill.

2270 Barney Rd.• Anderson, CA 96007www.outdoorcreations.com

Remove two opposing bolts and attach chain or other lifting device with ½” X 1 ½” coarse thread bolts.

*When removing planter from pallet for placement, place palletized item in final position to minimize travel time while hanging.

Use suitable equipment

(ie. Forklift, crane, front loader, etc) to lift planter.

Waste Receptacles (with rounded tops):

Planters:

Pre-place unit in final location by pallet. Insert padded forklift fork between opening and door, lift off of pallet, remove pallet and set receptacle in place.

Table Tennis Tables:

*Minimum 8,000 lb. lift required.

Forklift Fork

Net

6’ forks with padding

Forks with padding

Padding