Attachment_1_Specification.pdf

State of California Bid Specification #8940-0329203

Accoutrements i

Table of Contents

1.0 SCOPE

2.0 APPLICABLE LAWS AND INDUSTRY STANDARDS

3.0 TECHNICAL REQUIREMENTS

3.1 Shoulder Mark, Class B Uniforms

3.1.1 Non-Commissioned Officer (NCO) Grade

3.1.2 Officer Grade

3.1.3 Grizzly Grade

3.2 Metal Pin-On Insignia, Shield, Class B Uniforms

3.2.1 Distinguished Unit Insignia (DUI)

3.2.2 Fieldcraft Insignia

3.2.3 Cadet Mountaineer Insignia

3.2.4 Cadet Medic Insignia

3.2.5 Cadet Drill Instructor Insignia

3.2.6 Cadet Law Enforcement Badge

3.2.7 Cadet Cyber Badge

3.2.8 Drill and Ceremonies Badge

3.2.9 Public Safety Badge

3.2.10 Recondo Badge

3.2.11 Engineer Badge

3.2.12 Drone Pilot Badge

3.2.13 CAL Insignia

3.2.14 Cadet Corps Lapel Insignia

3.2.15 Commandant, Insignia Branch, CACC Officer

3.2.16 Commandant, Insignia Branch, CACC Enlisted

3.2.17 Commandant, CA Insignia, Officer

3.2.18 Commandant, CA Insignia, Enlisted

3.2.19 Officer Grade, Rank Insignia

3.3 Buttons, State of California ‘Eureka’ Seal

3.3.1 Coat Pocket, Male, Set of 4

3.3.2 Coat, Male, Set of 6

3.3.3 Coat Pocket, Female, Set of 4

3.3.4 Cap Screw, Set of 2

3.4 Qualification Badges and Bars

3.4.1 Honor Cadet Bar

3.4.2 Honor Cadet Officer Bar

3.4.3 Honor Cadet Summer Camp Bar

3.4.4 Honor Cadet Officer Summer Camp Bar

3.4.5 Marksmanship Badge

3.4.6 Sharpshooter Badge

3.4.7 Expert Badge

3.4.8 Small Bore Rifle Bar

BU 8940 Event ID 0000031334 Attachment 1

Accoutrements ii

3.4.9 Air Rifle Bar

3.5 Service Cap Devices

3.5.1 Drill Instructor Campaign Cover Pin

3.5.2 Commandant Commissioned Officer Cap Device

3.5.3 Commandant Enlisted Cap Device

3.6 Neckwear and accessories

3.6.1 Neck Tab, Female, Class B Uniform

3.6.2 Tie, Clip On

3.6.3 Tie, Four-in-Hand

3.7 Uniform accessories

3.7.1 Gloves, Honor Guard

3.7.2 Belt, Rigger

3.7.3 Belt and Buckle, Dress

3.7.4 Elastic Bands, Boot (Trouser Blousers)

3.8 Cord, Shoulder

3.8.2 Brigade Staff Shoulder Cord

3.8.3 Color Guard and Flag Detail Shoulder Cord

3.8.4 Drill Team Shoulder Cord

3.8.5 Superior Uniform Inspection Shoulder Cord

3.8.6 Regimental or Battalion Staff Shoulder Cord

3.9 Patches

3.9.1 California Cadet Corps Shield, Black and Coyote Brown

3.9.2 California Cadet Corps Shield, Coyote Brown and Black

3.9.3 California Cadet Corps Shield, Blue and Gold

3.9.4 California Flag

3.9.5 CA Cadet Corps Nametape

3.9.6 Enlisted Rank

3.9.7 Officer Rank

3.9.8 Grizzly Rank

3.9.9 Tabs, Accomplishment

3.10 Duty Patches

3.10.1 Company

3.10.2 Battalion

3.10.3 Brigade

3.10.4 10th Corps

3.11 Ribbon Mounting Bars, Ribbons, and Devices

3.11.1 Ribbon Mounting Bars

3.11.2 Ribbons

3.11.3 Devices

3.12 Medals, Draped

3.12.1 Drape

3.12.2 Medal

3.12.2.1 Design 1

iii

3.12.2.2 Design 2

3.12.2.3 Design 3

3.12.2.4 Design 4

3.12.2.5 Design 5

3.12.3 Medal Packaging Requirements

Appendix A: Complete Ribbon Chart

Appendix B: Medal Sets iv

FIGURES

Figure 1: Shoulder Mark Ranks, Non-Commissioned Officer Figure 2: Shoulder Mark Ranks, Officer Figure 3: Shoulder Mark Ranks, Grizzly Figure 4: (Left) New CACC crest. (Right) Distinguished Unit Insignia dimensions Figure 5: Distinguished Unit Insignia, Back Figure 6: Fieldcraft Insignia, Front Figure 7: Fieldcraft Insignia, Back Figure 8: Cadet Mountaineer Insignia, Front Figure 9: Cadet Mountaineer Insignia, Back Figure 10: Cadet Medic Insignia, Front Figure 11: Medic Cadet Insignia, Back Figure 12: Cadet Drill Instructor Insignia, Front Figure 13: Cadet Drill Instructor Insignia, Back Figure 14: Cadet Law Enforcement Badge, Front Figure 15: Cadet Law Enforcement Badge, Back Figure 16: Cadet Cyber Badge, Front Figure 17: Cadet Cyber Badge, Back Figure 18: Drill and Ceremonies Badge, Front Figure 19: Drill and Ceremonies Badge, Back Figure 20: Public Safety Badge, Front Figure 21: Public Safety Badge, Back Figure 22: Recondo Badge, Front Figure 23: Recondo Badge, Back Figure 24: Engineer Badge, Front Figure 25: Engineer Badge, Back Figure 26: Drone Pilot Badge, Front Figure 27: Drone Pilot Badge, Back Figure 28: CAL Insignia, Front Figure 29: CAL Insignia, Back Figure 30: Cadet Corps Lapel Insignia, Front Figure 31: Cadet Corps Lapel Insignia, Back Figure 32: Commandant, Insignia Branch, CACC Officer, Front Figure 33: Commandant, Insignia Branch, CACC Officer, Back Figure 34: Commandant, Insignia Branch, CACC Enlisted, Front Figure 35: CA Insignia, Officer, Front Figure 36: CA Insignia, Enlisted, Front Figure 37: Rank Insignia, Officer, Front Figure 38: Buttons, Eureka, Front Figure 39: Buttons, Eureka, Back Figure 40: Cap Screw, Set of 2 Figure 41: Honor Cadet Bar, Front Figure 42: Honor Cadet Bar, Back Figure 43: Honor Cadet Officer Bar, Front Figure 44: Honor Cadet Officer Bar, Back Figure 45: Honor Cadet Summer Camp Bar, Front v

Figure 46: Honor Cadet Summer Camp Bar, Back Figure 47: Honor Cadet Officer Summer Camp Bar, Front Figure 48: Honor Cadet Officer Summer Camp Bar, Back Figure 49: Marksmanship Badge, Front Figure 50: Sharpshooter Badge, Front Figure 51: Expert Badge, Front Figure 52: Small Bore Rifle Bar, Front Figure 53: Air Rifle Bar, Front Figure 54: (Left) New CACC crest design. (Right) Drill Instruction Campaign Cover Pin Front for reference Figure 55: Drill Instructor Campaign Cover Pin, Back Figure 56: Commandant Commissioned Officer Cap Device, Front Figure 57: Commandant Commissioned Officer Cap Device, Back Figure 58: Commandant Enlisted Cap Device, Front Figure 59: Commandant Enlisted Cap Device, Back Figure 60: Neck Tab, Female Figure 61: Tie, Clip on Figure 62: Tie, Four-in-Hand Figure 63: Gloves, Honor Guard Figure 64: Belt, Rigger Figure 65: Belt and Buckle, Dress Figure 66: Boot Bands Figure 67: Shoulder Cord Loop Attachment Epaulette Example Figure 68: Brigade Staff Shoulder Cord Figure 69: Color Guard and Flag Detail Shoulder Cord Figure 70: Drill Team Shoulder Cord Figure 71: Superior Uniform Inspection Shoulder Cord Figure 72: Regimental or Battalion Staff Shoulder Cord Figure 73: California Cadet Corps Shield, Black and Coyote Brown Figure 74: California Cadet Corps Shield, Coyote Brown and Black Figure 75: California Cadet Corps Shield, Blue and Gold Figure 76: California Flag Patch Figure 77: CA Cadet Corps Nametape Figure 78: Enlisted Rank Patches Figure 79: Officer Rank Patches Figure 80: Grizzly Rank Patches Figure 81: Accomplishment Tabs Figure 82: Company Patches, Positions Figure 83: Battalion Patches, Positions Figure 84: Brigade Patches, Positions Figure 85: 10th Corps, Positions Figure 86: 10th Corps, Medic Position Figure 87: Ribbon Mounting Bar Configurations Figure 88: Ribbon Devices, Star and Oak Leaf Clusters Figure 89: Ribbon Device, Bronze Star Example Figure 90: Drapes vi

Figure 91: Drape, Metal, and Ring Attachment Figure 92: Medal Design 1 Figure 93: Medal Design 2 Figure 94: Medal Design 3 Figure 95: Medal Design 4 Figure 96: Medal Design 5 Figure 97: Medal Packaging, Front Figure 98: Medal Packaging, Back vii

TABLES

Table 1: Ribbon Bar Configurations

WANG, T 1 April 23, 2024

1.0 SCOPE

This specification defines the minimum requirements for military insignias and accoutrements for the California Military Department, California Cadet Corps (CACC). Insignias and accoutrements will be worn on Class C and Class B Uniforms. They are intended for normal wear on the field and are awarded for accomplishments of individual cadets or the unit.

2.0 APPLICABLE LAWS AND INDUSTRY STANDARDS

None.

3.0 TECHNICAL REQUIREMENTS

Figures found throughout this document are for illustration purposes, the text requirements hereafter take precedence over the figures.

3.1 Shoulder Mark, Class B Uniforms

Shoulder marks shall be made as follows:

a. Fabric: Reinforced cloth, black, sown along the back to form a flat tube shape that slides onto the shoulder flap of a Class B dress shirt.

b. Size: Shoulder marks shall come in two sizes.

(1) Short: 2-1/8 inch wide at the base, 3-1/4 inch in length, tapering to 1-7/8 inch wide at the top.

(2) Long: 2-1/8 inch wide at the base, 4-1/4 inch in length, tapering to 1-7/8 inch wide at the top.

c. Marks shall come in pairs.

3.1.1 Non-Commissioned Officer (NCO) Grade

a. Design: NCO marks shall be designed as shown in Figure 1. Each gold-colored stripe shall be 1/4 inch wide. Each stripe and rocker shall be spaced 1/8 inch apart.

b. Embroidery: Ranks shall be centered horizontally, embroidered in gold-colored thread, and wrapped around the edge so the ending is hidden from view when worn on a Class B shirt.

c. Ranks for NCO are as follow:

(1) Cadet

(2) Cadet First Class

(3) Cadet Corporal

(4) Cadet Sergeant

(5) Cadet Staff Sergeant

(6) Cadet Sergeant First Class

(7) Cadet Master Sergeant

(8) Cadet First Sergeant

(9) Cadet Major Sergeant

(10) Cadet Command Sergeant Major

Bid Specification

WANG, T 2 April 23, 2024

Figure 1: Shoulder Mark Ranks, Non-Commissioned Officer

WANG, T 3 April 23, 2024

3.1.2 Officer Grade

a. Design: Officer shoulder marks shall be made as shown in Figure 2.

b. Cadet Corps Shield: Blue and gold-colored thread measuring 1-1/16 inch wide and 1-1/2 inch tall to the top of the narrow side. The shield shall be positioned 1/2 inch away from the top edge.

c. Ranks for Officer are as follow:

(1) Officer Candidate

(2) 2nd Lieutenant

(3) 1st Lieutenant

(4) Captain

(5) Major

(6) Lieutenant Colonel

(7) Colonel

Figure 2: Shoulder Mark Ranks, Officer

WANG, T 4 April 23, 2024

3.1.3 Grizzly Grade

a. Design: Grizzly shoulder marks shall be made as shown in Figure 3.

b. Embroidery: Grizzly bears shall be centered horizontally and embroidered gold-colored thread. Each bear shall measure 3/4 inch wide and 3/8 inch tall.

c. Ranks for Grizzly are as follow:

(1) Grizzly 1

(2) Grizzly 2

(3) Grizzly 3

(4) Grizzly 4

Figure 3: Shoulder Mark Ranks, Grizzly

WANG, T 5 April 23, 2024

3.2 Metal Pin-On Insignia, Shield, Class B Uniforms

a. Material: Metal.

b. Back Design: Cross-hatching, see Figure 37 for reference.

3.2.1 Distinguished Unit Insignia (DUI)

a. Dimensions: 1 inch at the widest point and 1-1/4 inch in height.

b. Front Design: The DUI shall be a miniature gold-colored metal reproduction of the new CACC crest with a bear, torch, and sword on a dark blue background as shown in Figure 4 (Left).

Figure 4: (Left) New CACC crest. (Right) Distinguished Unit Insignia dimensions.

c. Back Design: The back shall be solid gold color with two butterfly clutch fasteners placed near the top corners of the shield as shown in Figure 5.

Figure 5: Distinguished Unit Insignia, Back

WANG, T 6 April 23, 2024

3.2.2 Fieldcraft Insignia

a. Dimensions: 1-1/2 inch wide and 1-3/4 inch tall.

b. Front Design: The Fieldcraft Insignia shall be gold color with a growling bear.

The scroll at the bottom shall have written in capital letters “FIELDCRAFT” as shown in Figure 6.

Figure 6: Fieldcraft Insignia, Front

c. Back Design: The back shall be solid gold-colored with three butterfly clutch fasteners at the corners of the shield as shown in Figure 7.

Figure 7: Fieldcraft Insignia, Back

WANG, T 7 April 23, 2024

3.2.3 Cadet Mountaineer Insignia

a. Dimensions: 1-1/2 inch wide and 1-1/2 inch tall.

b. Front Design: The Cadet Mountaineer Insignia shall be gold color with a ram’s head. The top of the badge written in capital letters “CADET” and on the bottom scroll written in capital letters “MOUNTAINEER” as shown in Figure 8.

Figure 8: Cadet Mountaineer Insignia, Front fasteners centered horizontally as shown in Figure 9.

Figure 9: Cadet Mountaineer Insignia, Back

WANG, T 8 April 23, 2024

3.2.4 Cadet Medic Insignia

a. Dimensions: 1 inch wide and 1-1/2 inch tall.

b. Front Design: The Cadet Medic Insignia shall be solid gold color with a picture of the medical branch insignia as shown in Figure 10. “CADET” shall be bordered and written in capital letters. The CADET bordering shall be 1-1/4 inch wide and 3/8 inch tall.

Figure 10: Cadet Medic Insignia, Front fasteners centered horizontally as shown in Figure 11.

Figure 11: Medic Cadet Insignia, Back

WANG, T 9 April 23, 2024

3.2.5 Cadet Drill Instructor Insignia

a. Dimensions: 1-1/2 inch wide and 1-1/2 inch tall.

b. Front Design: The Cadet Drill Instructor Insignia shall be gold color with three drill instructors positioned in front of a laurel wreath as shown in Figure 12. The bottom scroll shall have written in black letters “Cadet Drill Instructor”.

Figure 12: Cadet Drill Instructor Insignia, Front

Note: The first letter of each word is capitalized while the other letters are in lower case.

c. Back Design: The back shall be solid gold color with three butterfly clutch fasteners positioned at the corners as shown in Figure 13.

Figure 13: Cadet Drill Instructor Insignia, Back

WANG, T 10 April 23, 2024

3.2.6 Cadet Law Enforcement Badge

a. Dimensions: 1-1/2 inch in diameter.

b. Front Design: The Cadet Law Enforcement badge shall be a blue and silver colored shield featuring the CACC crest within a star as shown in Figure 14.

The words “CADET” shall be centered horizontally across the top and “LAW ENFORCEMENT” shall be centered horizontally across the bottom in blue capital letters.

Figure 14: Cadet Law Enforcement Badge, Front fasteners centered horizontally as shown in Figure 15.

Figure 15: Cadet Law Enforcement Badge, Back

WANG, T 11 April 23, 2024

3.2.7 Cadet Cyber Badge

a. Dimensions: 1-3/8 inch wide and 1-1/2 inch tall.

b. Front Design: The Cadet Cyber Badge shall have one sword and two crossed lightning rods in gold color centered horizontally on a black background as shown in Figure 16. The badge shall have a double gold color border. The words “CADET” and “CYBER” shall be centered horizontally on the top and bottom in white capital letters with a gold color outline.

Figure 16: Cadet Cyber Badge, Front fasteners positioned as shown in Figure 17.

Figure 17: Cadet Cyber Badge, Back

WANG, T 12 April 23, 2024

3.2.8 Drill and Ceremonies Badge

a. Dimensions: 1-1/2 inch in diameter.

b. Front Design: The insignia consists of a cadet holding an American flag, cross rifles and a drill and ceremonies badge with two yellow stars, one on the right and one on the left of the device, as shown in Figure 18.

Figure 18: Drill and Ceremonies Badge, Front fasteners positioned as shown in Figure 19.

Figure 19: Drill and Ceremonies Badge, Back

WANG, T 13 April 23, 2024

3.2.9 Public Safety Badge

a. Dimensions: 1-1/4 inch wide by 1-1/2 inch tall

b. Front Design: The badge is red, blue, and gold. The insignia consists of a public safety shield, with the first responder insignia on the center with top banner to read “PUBLIC” and a bottom banner to read “SAFETY” as shown on Figure 20.

Figure 20: Public Safety Badge, Front fasteners positioned as shown in Figure 21.

Figure 21: Public Safety Badge, Back

WANG, T 14 April 23, 2024

3.2.10 Recondo Badge

a. Dimensions: 1 inch wide by 1-1/4inch tall

b. Front Design: The badge is black and gold. Arrowhead arrow with torch on center shown in Figure 22.

Figure 22: Recondo Badge, Front

c. Back Design: The back shall have two butterfly clutch fasteners positioned as shown in Figure 23.

Figure 23: Recondo Badge, Back

WANG, T 15 April 23, 2024

3.2.11 Engineer Badge

a. Dimensions: 1-1/8 inch wide by 3/4 inch tall

b. Front Design: The badge is gold. The insignia is a castle shown in Figure 24.

Figure 24: Engineer Badge, Front fasteners positioned as shown in Figure 25.

Figure 25: Engineer Badge, Back

WANG, T 16 April 23, 2024

3.2.12 Drone Pilot Badge

a. Dimensions: 3 inch wide by 1-1/2 inch tall

b. Front Design: The badge is silver. The insignia is a drone with wings. To read

“CADET DRONE PILOT” on the top banner in-place of “FAA LICENSED DRONE PILOT” as shown on Figure 26.

Figure 26: Drone Pilot Badge, Front

c. Back Design: The back shall be solid silver-color with two butterfly clutch fasteners positioned as shown in Figure 27.

Figure 27: Drone Pilot Badge, Back

WANG, T 17 April 23, 2024

3.2.13 CAL Insignia

a. Dimensions: 1-1/4inch wide and 1/2 inch tall.

b. Front Design: The CAL Insignia shall be “CAL” in gold color capital letters with beveled edges as shown in Figure 28.

Figure 28: CAL Insignia, Front fasteners positioned as shown in Figure 29.

Figure 29: CAL Insignia, Back

WANG, T 18 April 23, 2024

3.2.14 Cadet Corps Lapel Insignia

a. Dimensions: 3/4 inch wide and 3/4 inch tall.

b. Front Design: The Cadet Corps Lapel Insignia shall be gold color with crossed rifles surrounded by a laurel wreath as shown in Figure 30.

Figure 30: Cadet Corps Lapel Insignia, Front fasteners positioned as shown in Figure 31.

Figure 31: Cadet Corps Lapel Insignia, Back

WANG, T 19 April 23, 2024

3.2.15 Commandant, Insignia Branch, CACC Officer

a. Dimensions: 1 inch wide and 1 inch tall.

b. Front Design: The Commandant, CACC Officer insignia shall have gold color crossed swords on the torch of learning surrounded by a blue laurel wreath with a gold color California Grizzly Bear as shown in Figure 32.

Figure 32: Commandant, Insignia Branch, CACC Officer, Front

c. Back Design: The back shall be gold color with two butterfly clutch fasteners centered horizontally as shown in Figure 33.

Figure 33: Commandant, Insignia Branch, CACC Officer, Back

WANG, T 20 April 23, 2024

3.2.16 Commandant, Insignia Branch, CACC Enlisted

b. Front Design: The Commandant, CACC Enlisted insignia shall have gold crossed swords on the torch of learning surrounded by a blue laurel wreath with a gold California Grizzly Bear. The insignia shall be placed on top of a 1 inch diameter gold color metal disk as shown in Figure 34.

Figure 34: Commandant, Insignia Branch, CACC Enlisted, Front

Note: This front design is like Figure 32 but with the addition of the gold color metal disk.

c. Back Design: The back shall be gold color with two butterfly clutch fasteners centered horizontally on the metal disk. One fastener at the top and one at the bottom.

3.2.17 Commandant, CA Insignia, Officer

a. Dimensions: 3/4 inch wide and 7/16 inch tall.

b. Front Design: The Commandant, CA Officer insignia shall be “CA” in gold capital letters with beveled edges as shown in Figure 35.

Figure 35: CA Insignia, Officer, Front fasteners on the left and right edges. This design shall be similar to the back of the CAL insignia shown in Figure 29.

WANG, T 21 April 23, 2024

3.2.18 Commandant, CA Insignia, Enlisted

a. Dimensions: 1 inch in diameter.

b. Front Design: The Commandant, CA Enlisted insignia shall be “CA” in gold capital letters with beveled edges placed on top of a 1 inch diameter gold-colored disk. See Figure 36 for reference.

Figure 36: CA Insignia, Enlisted, Front

c. Back Design: The back shall be solid gold-color, with two butterfly clutch fasteners on the left and right edges of the disk.

WANG, T 22 April 23, 2024

3.2.19 Officer Grade, Rank Insignia

a. Dimensions:

(1) Single Disc: 3/4 inch in diameter.

(2) Double Disc: 2 inch wide and 3/4 inch tall.

(3) Single Diamond: 3/4 inch wide and 1-1/4inch tall.

(4) Double Diamond: 1-1/2 inch wide and 1-1/4 inch tall.

b. Design: Insignia of grade is designed as a flat metal, beveled with inset cross-hatching. Officer pin on rank shall be made as shown in Figure 37.

c. Rank for Officer are as follows:

(5) OC: Single Disc, Red Plated

(6) 2LT: Single Disc, Gold Plated

(7) 1LT: Single Disc, Silver Plated

(8) CPT: Double Disc, Silver Plated

(9) MAJ: Single Diamond, Gold Plated

(10) LTC: Single Diamond, Silver Plated

(11) COL: Double Diamond, Silver Plated

Figure 37: Rank Insignia, Officer, Front

d. Back Design: The back shall be solid in color with two butterfly clutch fasteners on the left and right edges of the disk.

WANG, T 23 April 23, 2024

3.3 Buttons, State of California ‘Eureka’ Seal

a. Front Design: The buttons shall be gold-color, dome shape, and have a detailed image of the State of California ‘Eureka’ Seal as shown in Figure 38.

Note: The State of California ‘Eureka’ Seal shall not be flat.

Figure 38: Buttons, Eureka, Front

b. Back Design: The back of the button shall be gold color with a shank loop as shown in Figure 39.

Figure 39: Buttons, Eureka, Back

WANG, T 24 April 23, 2024

3.3.1 Coat Pocket, Male, Set of 4

a. Dimensions: Each button and washer shall be 15 mm in diameter.

b. Packaging: A set shall consist of four buttons, four gold color washers, and four gold color toggle pins all packaged in a poly bag.

3.3.2 Coat, Male, Set of 6

a. Dimensions: Each button and washer shall be 23 mm in diameter.

b. Packaging: A set shall consist of six buttons, six gold color washers, and six gold color toggle pins all packaged in a poly bag.

3.3.3 Coat Pocket, Female, Set of 4

a. Dimensions: Each button and washer shall be 19 mm in diameter.

b. Packaging: A set shall consist of four buttons, four gold color washers, and four gold color toggle pins all packaged in a poly bag.

3.3.4 Cap Screw, Set of 2

c. Dimensions: Each button and washer shall be 15 mm in diameter with a 6-32 coarse thread screw-post backing as shown in the figure below.

d. Packaging: A set shall consist of 2 screw-post backing buttons, all packaged in a poly bag.

Figure 40: Cap Screw, Set of 2

WANG, T 25 April 23, 2024

3.4 Qualification Badges and Bars

3.4.1 Honor Cadet Bar

a. Dimensions: 2-1/8 inch wide and 1/2 inch tall.

b. Front Design: The Honor Cadet Bar read “CALIFORNIA CADET CORPS” on first line and “HONOR CADET” on second line in gold color capital letters on black background with gold edge as shown in Figure 41.

Figure 41: Honor Cadet Bar, Front positioned as shown in Figure 42.

Figure 42: Honor Cadet Bar, Back

WANG, T 26 April 23, 2024

3.4.2 Honor Cadet Officer Bar

a. Dimensions: 2-1/8 inch wide and 1/2 inch tall.

b. Front Design: The Honor Cadet Bar shall read “CALIFORNIA CADET CORPS” on first line and “HONOR CADET OFFICER” on second line in gold color capital letters on black background with gold edge as shown in Figure 43.

Figure 43: Honor Cadet Officer Bar, Front positioned as shown in Figure 44.

Figure 44: Honor Cadet Officer Bar, Back

WANG, T 27 April 23, 2024

3.4.3 Honor Cadet Summer Camp Bar

b. Front Design: The Honor Cadet Bar shall read “CALIFORNIA CADET CORPS” on first line, “HONOR CADET” on second line, “SUMMER CAMP” on the third line in gold color capital letters on black background with gold edge as shown in Figure 45.

Figure 45: Honor Cadet Summer Camp Bar, Front positioned as shown in Figure 46.

Figure 46: Honor Cadet Summer Camp Bar, Back

WANG, T 28 April 23, 2024

3.4.4 Honor Cadet Officer Summer Camp Bar

b. Front Design: The Honor Cadet Bar shall read “CALIFORNIA CADET CORPS” on first line, “HONOR CADET OFFICER” on second line, “SUMMER CAMP” on the third line in gold color capital letters on black background with gold edge as shown in Figure 47.

Figure 47: Honor Cadet Officer Summer Camp Bar, Front positioned as shown in Figure 48.

Figure 48: Honor Cadet Officer Summer Camp Bar, Back

WANG, T 29 April 23, 2024

3.4.5 Marksmanship Badge

b. Front Design: The marksmanship badge is shiny silver metal in color. It is the same design as the Army Marksmanship Qualification Badge as shown in Figure 49.

Figure 49: Marksmanship Badge, Front

c. Back Design: The back shall be silver color with two butterfly clutch fasteners, one on the left and one on the right edge of the Badge.

3.4.6 Sharpshooter Badge

a. Dimensions: 1 inch wide and 1 inch tall.

b. Front Design: The Sharpshooter badge is shiny silver metal in color. It is the same design as the Army Sharpshooter Qualification Badge as shown in Figure 50.

Figure 50: Sharpshooter Badge, Front

d. Back Design: The back shall be silver color with two butterfly clutch fasteners, one on the left and one on the right edge of the Badge.

Accoutrements

WANG, T 30 April 23, 2024

3.4.7 Expert Badge

a. Dimensions: 1-1/8 inch wide and 1-1/8 inch tall.

b. Front Design: The Expert badge is shiny silver metal in color. It is the same design as the Army Expert Qualification Badge as shown in Figure 51.

Figure 51: Expert Badge, Front

c. Back Design: The back shall be silver color with two butterfly clutch fasteners on the left and right edges of the disk.

WANG, T 31 April 23, 2024

3.4.8 Small Bore Rifle Bar

a. Dimensions: 1 inch wide and 1/4 inch tall.

b. Front Design: The Small Bore Rifle bar is shiny silver metal in color. It is the same design as the Army Small Bore Rifle bar as shown in Figure 52.

Figure 52: Small Bore Rifle Bar, Front

c. Back Design: The back shall be silver color.

3.4.9 Air Rifle Bar

d. Dimensions: 1 inch wide and 1/4 inch tall.

e. Front Design: The Air Rifle bar is shiny silver metal in color. It is the same design as the JROTC Air Rifle bar as shown in Figure 53.

Figure 53: Air Rifle Bar, Front

f. Back Design: The back shall be silver color.

WANG, T 32 April 23, 2024

3.5 Service Cap Devices

3.5.1 Drill Instructor Campaign Cover Pin

a. Dimensions: 1 inch in diameter.

b. Front Design: The insignia consists of the California Cadet Corps Shield on gold disk. The disk and the shield come apart. Use the new crest design as shown in Figure 54 (Left).

Figure 54: (Left) New CACC crest design. (Right) Drill Instruction Campaign Cover Pin Front for reference.

c. Back Design: The back shall be solid gold color with a screw attached to the CACC Shield. The washer holds the two pieces together as positioned as shown in Figure 55.

Figure 55: Drill Instructor Campaign Cover Pin, Back

Accoutrements

WANG, T 33 April 23, 2024

3.5.2 Commandant Commissioned Officer Cap Device

a. Dimensions: 2-3/8 inch in height.

b. Front Design: The insignia is the partial coat of arms of the United States with the seal of California superimposed on the top, gold-colored metal Figure 56.

Figure 56: Commandant Commissioned Officer Cap Device, Front

c. Back Design: The back shall be solid gold color with a screw attached to the CACC Shield. The washer holds the two pieces together as positioned as shown in Figure 57.

Figure 57: Commandant Commissioned Officer Cap Device, Back

Accoutrements

WANG, T 34 April 23, 2024

3.5.3 Commandant Enlisted Cap Device

d. Dimensions: 1-1/2 inch in diameter.

e. Front Design: The insignia is a plain, gold-colored disk with a gold-colored partial coat of arms of the United States with the Seal of California superimposed on the top attached to the disk Figure 58.

Figure 58: Commandant Enlisted Cap Device, Front

f. Back Design: The back shall be solid gold color with a screw attached to the CACC Shield. The washer holds the two pieces together as positioned as shown in Figure 59.

Figure 59: Commandant Enlisted Cap Device, Back

WANG, T 35 April 23, 2024

3.6 Neckwear and accessories

3.6.1 Neck Tab, Female, Class B Uniform

a. Fabric: Plain weave, Polyester Poplin

b. Color: Black

c. Size: 16

d. Design: Pre-cured durable press, inverted V-shape as shown in Figure 60. The neck tab shall wrap around the neck under the collar of the female tan long short sleeved uniform shirt.

e. Fastener: Hook-and-loop

Figure 60: Neck Tab, Female

3.6.2 Tie, Clip On

a. Fabric: Polyester poplin

b. Color: Black

c. Dimensions: 14 inch long, 3-1/4 inch wide at the end, taper to a 2 inch width at the place of the triangle knot. The clip shall be centered behind the knot. The tie shall narrow to 1-3/8 inch width along the narrow end of the tie. See Figure 61 for reference.

Figure 61: Tie, Clip on

Accoutrements

WANG, T 36 April 23, 2024

3.6.3 Tie, Four-in-Hand

a. Fabric: Polyester poplin

b. Color: Black

c. Design: Two-fold, four-in-hand with pointed ends. See Figure 62 for reference.

d. Dimensions: 58 inch long and 2-1/2 inch wide at the widest point.

Figure 62: Tie, Four-in-Hand

WANG, T 37 April 23, 2024

3.7 Uniform accessories

3.7.1 Gloves, Honor Guard

a. Fabric: Cotton and spandex

b. Design: Four-finger-and-thumb

c. Style: Slip-on

d. Grip: Rubber-like grip dots (Reference: “Sure-Grip”)

e. Color: White

f. Glove length: 10-1/2 inch – 11 inch

g. Gloves shall be the following sizes:

(1) Small/Medium

(2) Large/X-Large

Figure 63: Gloves, Honor Guard

Accoutrements

WANG, T 38 April 23, 2024

3.7.2 Belt, Rigger

a. Material: Nylon Webbing

b. Color: Black

c. Design: The belt shall be rigger style with a metal belt buckle and adjustable cargo. See Figure 64 for reference.

d. Belt width: 1-1/4 inch

e. Belts shall come in the following lengths:

(1) Small – 28 inch

(2) Medium – 34 inch

(3) Large – 40 inch

(4) X-Large – 46 inch

(5) XX-Large – 52 inch

Figure 64: Belt, Rigger

Accoutrements

WANG, T 39 April 23, 2024

3.7.3 Belt and Buckle, Dress

f. Material: Nylon Webbing

g. Color: Black

h. Design: The belt shall be an elastic belt with solid brass buckle and brass tip.

Meets the specifications for wear with US Army ASU, removable buckle for easy replacement. Buckle has teeth that attach to fabric. See Figure 65 for reference.

i. Belt width: 1-1/4 inch

j. Belts shall come in the following length: 44 inch

k. Buckle Size: 1-1/4 wide

Figure 65: Belt and Buckle, Dress

3.7.4 Elastic Bands, Boot (Trouser Blousers)

a. Design: Bands shall be made with an elastic material (e.g. rubber or polyester) and have a metal hook to clamp the ends together. See Figure 66 for reference.

b. Length: 7-1/2 inch (slack)

c. Color: Black, green, or tan

d. Packaging: A pair of two (2) bands shall be packaged in a poly bag.

Figure 66: Boot Bands

WANG, T 40 April 23, 2024

3.8 Cord, Shoulder

a. Design: Shoulder cords shall be a single braid formed by a series of interlocking square knots around a center cord. (Reference: U.S. Army, Infantry Shoulder Cord) Note: Cords with knots, tips, strands, or additional braids will not be accepted.

b. Shoulder cords shall have a wide loop to slip under the epaulette for attachment as shown in Figure 67.

c. Length: 30 inch

d. The following shoulder cord designs will not be accepted:

(1) Aiguilettes

(2) Fourrageres

Figure 67: Shoulder Cord Loop Attachment Epaulette Example

WANG, T 41 April 23, 2024

3.8.2 Brigade Staff Shoulder Cord

a. Style: Two-color intertwined.

b. Color: Blue and gold as shown in Figure 68.

Figure 68: Brigade Staff Shoulder Cord

3.8.3 Color Guard and Flag Detail Shoulder Cord

a. Style: Two-color intertwined.

b. Color: Red and white as shown in Figure 69.

Figure 69: Color Guard and Flag Detail Shoulder Cord

Accoutrements

WANG, T 42 April 23, 2024

3.8.4 Drill Team Shoulder Cord

a. Style: One-color braid.

b. Color: White as shown in Figure 70.

Figure 70: Drill Team Shoulder Cord

3.8.5 Superior Uniform Inspection Shoulder Cord

a. Style: One-color braid.

b. Color: Gold as shown in Figure 71.

Figure 71: Superior Uniform Inspection Shoulder Cord

3.8.6 Regimental or Battalion Staff Shoulder Cord

a. Style: One-color braid.

b. Color: Royal blue as shown in Figure 72.

Figure 72: Regimental or Battalion Staff Shoulder Cord

WANG, T 43 April 23, 2024

3.9 Patches

Military Style Patches will be for Class C Uniforms.

3.9.1 California Cadet Corps Shield, Black and Coyote Brown

a. Dimensions: 3 inch wide and 3-1/2 inch tall.

b. Front Design: CACC Crest (bear, torch, and sword) embroidered in coyote brown thread on a black background as shown in Figure 73. The words “CALIFORNIA CADET CORPS” written in capital letters across the top of the patch.

Note: Embroidery using standard brown thread will not be accepted.

c. Stitches: 12,000 minimum

d. Back: Hook backing

e. Edging: Merrowed

Figure 73: California Cadet Corps Shield, Black and Coyote Brown

Accoutrements

WANG, T 44 April 23, 2024

3.9.2 California Cadet Corps Shield, Coyote Brown and Black

a. Dimensions: 3 inch wide and 4-1/8 inch tall.

b. Front Design: CACC Crest (bear, torch, and sword) embroidered in black thread on a coyote brown background as shown in Figure 74. The words “CALIFORNIA CADET CORPS” written in capital letters across the top of the patch.

Note: Embroidery using standard brown thread will not be accepted.

c. Stitches: 12,000 minimum

d. Back: Hook backing

e. Edging: Merrowed

Figure 74: California Cadet Corps Shield, Coyote Brown and Black

Accoutrements

WANG, T 45 April 23, 2024

3.9.3 California Cadet Corps Shield, Blue and Gold

f. Dimensions: 3 inch wide and 4-1/8 inch tall.

g. Front Design: CACC Crest (bear, torch, and sword) embroidered in gold thread on a blue background as shown in Figure 75. The words “CALIFORNIA CADET CORPS” written in capital letters across the top of the patch.

h. Stitches: 12,000 minimum

i. Back: Iron-On

j. Edging: Merrowed

Figure 75: California Cadet Corps Shield, Blue and Gold

Accoutrements

WANG, T 46 April 23, 2024

3.9.4 California Flag

a. Dimensions: 3 inch wide and 2 inch tall.

b. Front Design: The California Flag Patch shall mirror the State of California flag as shown in Figure 76.

(1) Flag Color/Background: White

(2) Grass: Green with a brown outline.

(3) Bear: Two-tone with brown and tan.

(4) Bottom stripe: Red

(5) Star: Red

(6) Lettering: “CALIFORNIA REPUBLIC” in black capital letters written below the bear.

c. Stitches: ≥ 12,000 minimum

d. Back: Hook backing

e. Edging: Merrowed

Figure 76: California Flag Patch

WANG, T 47 April 23, 2024

3.9.5 CA Cadet Corps Nametape

a. Dimensions: 5-1/4 inch wide and 1 inch tall.

b. Fabric: Cotton

c. Front Design: The words “CA CADET CORPS” shall be written in all capital letters with coyote brown thread on a black background as shown in Figure 77.

The lettering shall be spaced 1/8 inch away from the top and bottom edge.

Note: Embroidery using standard brown thread will not be accepted.

d. Back: Hook backing

e. Edging: Edges shall match the U.S. Army’s OCP nametape.

Figure 77: CA Cadet Corps Nametape

3.9.6 Enlisted Rank

a. Dimensions: 2 inch wide and 2 inch tall.

b. Fabric: Cotton

c. Front Design: Enlisted Rank patches shall have the rank centered and embroidered with coyote brown thread on a black background as shown in Figure 78.

Note: Embroidery using standard brown thread will not be accepted.

d. Back: Hook backing

e. Edging: Edges shall match the U.S. Army’s rank patches.

f. Ranks for Enlisted Patches are as follows:

(1) Cadet (CDT)

(2) Cadet First Class (CFC)

(3) Cadet Corporal (C/CPL)

(4) Cadet Sergeant (C/SGT)

(5) Cadet Staff Sergeant

(C/SSG)

(6) Cadet Sergeant First Class (C/SFC)

(7) Cadet Master Sergeant (C/MSG)

(8) Cadet First Sergeant (C/1SG)

(9) Cadet Sergeant Major (C/SGM)

(10) Cadet Command Sergeant Major

(C/CSM)

Bid Specification Accoutrements

WANG, T 48 April 23, 2024

Figure 78: Enlisted Rank Patches

WANG, T 49 April 23, 2024

3.9.7 Officer Rank

a. Dimensions: 2 inch wide and 2 inch tall.

b. Fabric: Cotton

c. Design: Rank patches shall have the rank symbol (e.g. circle or diamond) centered and embroidered with colored thread on a black background as shown in Figure 79.

d. Color: Dark red, coyote brown, and gray for rank symbols.

Note: Embroidery using standard brown thread will not be accepted.

e. Back: Hook backing

f. Edging: Edges shall match the U.S. Army’s rank patches.

g. Rank for Officer patches are as follows:

(1) Officer Candidate

(2) 2nd Lieutenant (C/2LT)

(3) 1st Lieutenant (C/1LT)

(4) Captain (C/CPT)

(5) Major (C/MAJ)

(6) Lieutenant Colonel (C/LTC)

(7) Colonel (C/COL)

Figure 79: Officer Rank Patches

Accoutrements

WANG, T 50 April 23, 2024

3.9.8 Grizzly Rank

a. Dimensions: 2 inch wide and 2 inch tall.

b. Fabric: Cotton

c. Design: Grizzly bears shall be centered and embroidered with coyote brown thread on a black background as shown in Figure 80. Grizzly bears measure 3/4 inch wide and 3/8 inch tall.

Note: Embroidery using standard brown thread will not be accepted.

d. Back: Hook backing

e. Edging: Edges shall match the U.S. Army’s rank patches.

f. Ranks for Grizzly are: 1, 2, 3, and 4.

Figure 80: Grizzly Rank Patches

WANG, T 51 April 23, 2024

3.9.9 Tabs, Accomplishment

a. Dimensions: 2 inch wide and 11/16 inch tall.

b. Front Design: Tabs shall have the qualification embroidered in black thread and capital letters on a coyote brown background. Lettering shall be 5/16 inch tall.

The patch shall be in an arc shape as shown in Figure 81.

Note: Embroidery using standard brown thread will not be accepted.

c. Back: Hook backing

d. Edging: Merrowed

e. Qualifications are of the following:

(1) ACADEMIC

(2) RECRUITER

(3) SURVIVAL INSTR

(4) VOLUNTEER

(5) ATHLETE

(6) HEALTHY

(7) LEADER

(8) MARKSMAN

(9) PATRIOT

(10) DRILL TEAM

(11) FIELD EXPERT

(12) FIRST RESPONDER

(13) COMMANDANT

(14) RECONDO

(15) COLOR GUARD

Figure 81: Accomplishment Tabs

WANG, T 52 April 23, 2024

3.10 Duty Patches

a. Dimensions: 3 inch wide and 2 inch tall.

b. Front Design: Duty patches shall have the unit position embroidered in the center on a black background except for the 10th Corp, Medic position. The patch border shall share the same color as the unit position.

c. Back: Hook backing

d. Stitching: 1,200 minimum

e. Edging: Merrowed

3.10.1 Company

a. Color: Infantry blue (light blue)

Note: The color in Figure 82 does not depict infantry blue (light blue), but design is shown for reference.

b. Company positions are as follow:

(1) XO

(2) SL

(3) CO

(4) PL

(5) PSG

(6) 1SG

(7) S-1

(8) S-2

(9) S-3

(10) S-4

(11) S-5

(12) S-6

Figure 82: Company Patches, Positions

Accoutrements

WANG, T 53 April 23, 2024

3.10.2 Battalion

a. Color: Coyote brown as shown in Figure 83.

Note: Embroidery using standard brown thread will not be accepted.

b. Battalion positions are as follow:

(1) CO

(2) XO

(3) CSM

(4) S-1

(5) S-2

(6) S-3

(7) S-4

(8) S-5

(9) S-6

Figure 83: Battalion Patches, Positions

Accoutrements

WANG, T 54 April 23, 2024

3.10.3 Brigade

a. Color: Silver as shown in Figure 84.

b. Brigade positions are as follow:

(1) CO

(2) XO

(3) CSM

(4) S-1

(5) S-2

(6) S-3

(7) S-4

(8) S-5

(9) S-6

Figure 84: Brigade Patches, Positions

Accoutrements

WANG, T 55 April 23, 2024

3.10.4 10th Corps

a. Color: Gold as shown in Figure 85.The medic unit position shall be embroidered in black on a red background as shown in Figure 86.

b. 10th Corps positions are as follow:

(1) CO

(2) DC

(3) XO

(4) CSM

(5) HHC

(6) S-1

(7) S-2

(8) S-3

(9) S-4

(10) S-5

(11) S-6

(12) Medic

Figure 85: 10th Corps, Positions

Figure 86: 10th Corps, Medic Position

WANG, T 56 April 23, 2024

3.11 Ribbon Mounting Bars, Ribbons, and Devices

3.11.1 Ribbon Mounting Bars

a. Composition: Stainless Steel

b. Design: Ribbon bars shall be identical to the Army ribbon bars. Each ribbon bar shall be soldered to a metal piece allowing for the addition of rows. At least one row shall be added on a bar. Bars shall have a straight pin with butterfly clutch for attachment to any uniform.

c. Function: Each row shall fit a 3/8 inch tall ribbon when slid in.

d. Configurations: Table 1 and Figure 87.

Table 1: Ribbon Bar Configurations

Number of Ribbons Held by

Ribbon Bar

Number of Ribbon Rows per

Ribbon Bar

Dimensions (L x H inch)

Number of Butterfly Clutches

1 1 1-3/8 x 5/8 2 2 1 2-3/4 x 5/8 2 3 1 4-1/8 x 5/8 2 6 2 4 x 3/4 3 9 3 4 x 1-1/8 4

12 4 4 x 1-1/2 4 15 5 4 x 1-3/4 4 18 6 4 x 2 ¼ 4

Figure 87: Ribbon Mounting Bar Configurations

Accoutrements

WANG, T 57 April 23, 2024

3.11.2 Ribbons

a. Dimensions: 1-3/8 inch wide and 3/8 inch tall.

b. Color: Multi-colored as shown in Appendix A for the Complete Ribbon Chart.

c. Ribbon Types:

(1) Superior Unit Award

(2) Unit Community Service

Award

(3) Honor Unit

(4) Cadet Medal

(5) Cadet Service Medal

(6) Merit Ribbon

(7) IMA Overall Cadet – Sr

(8) IMA Overall Cadet – Jr

(9) IMA Officer – SR

(10) IMA Overall Cadet –

Elementary

(11) IMA Officer – JR

(12) IMA NCO – SR

(13) IMA NCO – JR

(14) IMA First Year Cadet – Sr

(15) IMA First Year Cadet – Jr

(16) Knight Marksmanship

(17) Speed Marksmanship

(18) Drill Down State – Sr

(19) Drill Down State – Jr

(20) Drill Down – Armed

(21) PLT Drill – Sr

(22) PLT Drill – Jr

(23) Platoon Drill – Armed

(24) SQD Drill – Sr

(25) SQD Drill – Jr

(26) Squad Drill – Armed

(27) Color Guard – Sr

(28) Color Guard – Jr

(29) Staff Ride

(30) O’Sullivan Marksmanship

Award

(31) Adjutant General Service

(32) Executive Officer Citation

(33) Summer Training

(34) Survival Training

(35) Mountaineering Training

(36) XTC Competition

(37) Distinguished Service

(38) Brigade Advisor Citation

(39) Brigade Cadre

(40) Brigade HQ Company

(41) Advanced Leadership School

(42) Intermediate Leadership School

(43) Basic Leadership School

(44) OCS

(45) Advanced NCO Course

(46) Basic NCO Course

(47) Exhibition Drill

(48) Land Nav Orienteering

(49) Drill Academy Graduation

(50) Principal’s Citation

(51) Commandant of Cadets Citation

(52) Essayons Award

(53) SAT/ACT Achievement

(54) Superior Scholarship

(55) Physical Fitness Competition

(56) Recruiting

(57) Physical Fitness Achievement

(58) Perfect Attendance

(59) Battalion Cadre

(60) Specialized Training

(61) Citizenship

(62) Color Guard and Flag Detail

(63) Parade Participation

(64) Drill Team

(65) Marksmanship Training

(66) First Aid Certification

(67) Hunter Safety Certification

(68) Disaster Preparedness

(69) Bivouac

(70) Individual Community SVC

(71) School Service

(72) State Service

Note: Challenge Program Awards and External Organization Awards are excluded.

WANG, T 58 April 23, 2024

3.11.3 Devices

a. Dimensions: The device shall be 5/16 inch in diameter from edge to edge.

Prongs shall be 7/16 inch long.

b. Design: Stars and oak left clusters as shown in Figure 88. Each device shall have two prongs for attachment on ribbons.

c. Composition: Brass or metal alloys.

d. Tiers:

(1) Bronze

(2) Silver

(3) Gold

Figure 88: Ribbon Devices, Star and Oak Leaf Clusters

Figure 89: Ribbon Device, Bronze Star Example

WANG, T 59 April 23, 2024

3.12 Medals, Draped

3.12.1 Drape

a. Dimensions: 1-3/8 inch wide and 1-7/16 inch tall (measured when looped in a metal ring and flattened).

b. Design: Drapes shall be multi-colored with the back consisting of a straight pin with two butterfly clutches for attachment to uniforms as shown in Figure 90.

Figure 90: Drapes

c. Medal Attachment: Drapes shall be attached to a 1/2 inch metal ring. The drape and 1/2 inch metal ring shall be attached to a 1/4 inch ring. The 1/4 inch ring shall be the connecting ring to the medal as shown in Figure 91.

Figure 91: Drape, Metal, and Ring Attachment

WANG, T 60 April 23, 2024

3.12.2 Medal

a. Material: Metal

b. Finish: Antique

c. Design: No. 1-5 or an equivalent design approved by CACC that represents the intended accomplishment of the medal design.

d. Medal Tiers: Medals shall be made for the following tiers:

(1) Gold

(2) Silver

(3) Bronze

3.12.2.1 Design 1

a. Dimensions: 1-5/8 inch in diameter from one edge of the star to the opposite end of the star.

b. Design: 10-point star with a banner centered as shown in Figure 92.

c. Banner: The banner shall be 11/16 inch wide and 5/16 tall. “DRILL” printed in all capital letters raised on the metal.

Figure 92: Medal Design 1

3.12.2.2 Design 2

a. Dimensions: 1-1/4 inch in diameter.

b. Design: Target of 5 circles with a wreath bordering around the bottom edge as shown in Figure 93.

c. Lettering: “CACC” in all capital letters raised and centered across the top.

Figure 93: Medal Design 2

WANG, T 61 April 23, 2024

3.12.2.3 Design 3

a. Dimensions: 1-1/4 inch in diameter.

b. Design: An eagle carrying a torch over a field of water as shown in Figure 94.

The clouds shall be in the background just behind the eagle.

Figure 94: Medal Design 3

3.12.2.4 Design 4

a. Dimensions: 1-1/2 inch wide and 1-3/4 inch tall.

b. Design: Eagle with its wings spreading out towards a lamp of knowledge and two books as shown in Figure 95. The lamp of knowledge and books shall be outlined in a circle. A banner shall span the top of the medal.

Figure 95: Medal Design 4

3.12.2.5 Design 5

a. Dimensions: 1-5/16 inch in diameter.

b. Design: Four (4) military personnel each carrying a flag as shown in Figure 96. The front flag shall be a fully colored, reversed, American flag.

Figure 96: Medal Design 5

Accoutrements

WANG, T 62 April 23, 2024

3.12.3 Medal Packaging Requirements

a. Medals, ribbons, and drapes shall be fully assembled and attached to a paper board as shown in Figure 97 and Figure 98. The complete set shall be sealed in a poly bag.

b. A complete list of medal sets can be found in Appendix B.

Figure 97: Medal Packaging, Front

Figure 98: Medal Packaging, Back

Appendix A - Complete Ribbon Chart Attachment 1

PRINCIPAL’S

CITATION

PHYSICAL FITNESS

ACHIEVEMENT

PHYSICAL FITNESS

COMPETITION

ESSAYONS

AWARD

EXHIBITION

DRILL

SUPERIOR

SCHOLARSHIP

SAT/ACT

ACHIEVEMENT

DISTINGUISHED

SERVICE

DRILL ACADEMY

GRADUATION

LAND NAV

ORIENTEERING

BASIC

NCO COURSE

BRIGADE ADVISOR

CITATION

BASIC

LEADERSHIP

SCHOOL

OCS

RECRUITING

XTC

CMPETITION

PERFECT

ATTENDACE

ADVANCED

NCO COURSE

BATTALION

CADRE

INTERMEDIATE

LEADERSHIP

SCHOOL

EXECUTIVE

OFFICER CITATION

COLOR

GUARD - SR

PLT DRILL-SR

SPEED

MARKSMANSHIP

IMA OFFICER -JR

California Cadet Corps Awards and Decorations

UNIT COMMUNITY

SERVICE AWARD

SUPERIOR

UNIT AWARD

IMA

OVERALL

CADET - SR

IMA OFFICER – SR

IMA

OVERALL

CADET - JR

MERIT

RIBBON

CADET MEDAL

CADET SERVICE

MEDAL

ADJUTANT GENERAL

SERVICE

SPECIALIZED

TRAINING

COLOR

GUARD - JR

SQD DRILL-JR

O’SULLIVAN

MARKSMANSHIP

AWARD

SQUAD DRILL -

ARMED 3507

SQD DRILL-SR

PLT DRILL-JR 3011 PLATOON DRILL

- ARMED 3502

DRILL DOWN -

ARMED 3522

DRILL DOWN

STATE -JR

DRILL DOWN

STATE-SR

MOUNTAINEERING

TRAINING

ADVANCED

LEADERSHIP

SCHOOL

BRIGADE HQ

COMPANY

BRIGADE

CADRE

SURVIVAL

TRAINING

MARKSMANSHIP

TRAINING

SUMMER

TRAINING

IMA FIRST YEAR

CADET - JR

INDIVIDUAL

COMMUNITY SVC

IMA FIRST YEAR

CADET - SR

IMA NCO - SR

IMA NCO - JR

KNIGHT

MARKSMANSHIP

1 of 1 1 July 2019

HONOR

UNIT

CITIZENSHIP

COMMANDANT

OF CADETS

CITATION

PARADE

PARTICIPATION

COLOR GUARD

AND FLAG DETAIL

DISASTER

PREPAREDNESS

HUNTER SAFETY

CERTIFICATION

FIRST AID

CERTIFICATION

DRILL TEAM

BIVOUAC

STATE SERVICE

SCHOOL

SERVICE

Unit Awards

Individual Awards

IMA OVERALL

CADET -

ELEMENTARY

STAFF RIDE

CHALLENGE

PROGRAM

AWARDS

EXTERNAL

ORGANIZATION

AWARDS

Appendix B Medals Set Attachment 1

1. Senior Div Out Overall Cdt Award 3606 with Gold Medal

2. Senior Div Out Overall Cdt Award 3606 with Silver Medal

3. Senior Div Out Overall Cdt Award 3606 with Bronze Medal

4. Junior Div Out Overall Cdt Award 3607 with Gold Medal

5. Junior Div Out Overall Cdt Award 3607 with Silver Medal

6. Junior Div Out Overall Cdt Award 3607 with Bronze Medal

7. Elementary Div Out Overall Cdt Award 3271 with Gold Medal

8. Elementary Div Out Overall Cdt Award 3271 with Silver Medal

9. Elementary Div Out Overall Cdt Award 3271 with Bronze Medal

10. Outstanding Cdt Officer 4002 Award with Gold Medal

11. Outstanding Cdt Officer 4002 Award with Silver Medal

12. Outstanding Cdt Officer 4002 Award with Bronze Medal

13. Outstanding Junior Div Cdt Junior Officer Award 4212 with Gold Medal

14. Outstanding Junior Div Cdt Junior Officer Award 4212 with Silver Medal

15. Outstanding Junior Div Cdt Junior Officer Award 4212 with Bronze Medal

16. Senior Div Outstanding NCO Award 3230 with Gold Medal

17. Senior Div Outstanding NCO Award 3230 with Silver Medal

18. Senior Div Outstanding NCO Award 3230 with Bronze Medal

19. Junior Div Outstanding NCO Award 3617 with Gold Medal

20. Junior Div Outstanding NCO Award 3617 with Silver Medal

21. Junior Div Outstanding NCO Award 3617 with Bronze Medal

22. Senior Div Outstanding 1st Yr Cdt Award 3516 with Gold Medal

23. Senior Div Outstanding 1st Yr Cdt Award 3516 with Silver Medal

24. Senior Div Outstanding 1st Yr Cdt Award 3516 with Bronze Medal

25. Junior Div Outstanding 1st Yr Cdt Award 3604 withGold Medal

26. Junior Div Outstanding 1st Yr Cdt Award 3604 with Silver Medal

27. Junior Div Outstanding 1st Yr Cdt Award 3604 with Bronze Medal

28. Knight Marksmanship Medal 3508 with Gold Medal

29. Knight Marksmanship Medal 3508 with Silver Medal

30. Knight Marksmanship Medal 3508 with Bronze Medal

31. Speed Marksmanship Medal 3278 with Gold Medal

32. Speed Marksmanship Medal 3278 with Silver Medal

33. Speed Marksmanship Medal 3278 with Bronze Medal

34. Brennan Sn Div Drill Down Award 3201 with Gold Medal

35. Brennan Sn Div Drill Down Award 3201 with Silver Medal

36. Brennan Sn Div Drill Down Award 3201 with Bronze Medal

37. Pyle Junior Div Drill Down Award 3221 with Gold Medal

38. Pyle Junior Div Drill Down Award 3221 with Silver Medal

39. Pyle Junior Div Drill Down Award 3221 with Bronze Medal

40. Armed Div Drill Down Award 3522 with Gold Medal

41. Armed Div Drill Down Award 3522 with Silver Medal

42. Armed Div Drill Down Award 3522 with Bronze Medal

43. Senior Div PLT Drill Award 3010 with Gold Medal

Appendix B Medals Set Attachment 1

44. Senior Div PLT Drill Award 3010 with Silver Medal

45. Senior Div PLT DrillAward 3010 with Bronze Medal

46. Junior Div PLT Drill Award 3011 with Gold Medal

47. Junior Div PLT Drill Award 3011 with Silver Medal

48. Junior Div PLT Drill Award 3011 with Bronze Medal

49. Armed Div PLT Drill Award 3502 with Gold Medal

50. Armed Div PLT Drill Award 3502 with Silver Medal

51. Armed Div PLT Drill Award 3502 with Bronze Medal

52. Senior Div Squad Drill Award 3411 with Gold Medal

53. Senior Div Squad Drill Award 3411 with Silver Medal

54. Senior Div Squad Drill Award 3411 with Bronze Medal

55. Junior Div Squad Drill Award 3414 with Gold Medal

56. Junior Div Squad Drill Award 3414 with Silver Medal

57. Junior Div Squad Drill Award 3414 with Bronze Medal

58. Armed Div Squad Drill Award 3507 with Gold Medal

59. Armed Div Squad Drill Award 3507 with Silver Medal

60. Armed Div Squad Drill Award 3507 with Bronze Medal

61. Senior Div Color Guard Award 3243 with Gold Medal

62. Senior Div Color Guard Award 3243 with Silver Medal

63. Senior Div Color Guard Award 3243 with Bronze Medal

64. Junior Div Color Guard Award 3325 with Gold Medal

65. Junior Div Color Guard Award 3325 with Silver Medal

66. Junior Div Color Guard Award 3325 with Bronze Medal

67. O'Sullivan Marksmanship Medal 3613 with Gold Medal

68. O'Sullivan Marksmanship Medal 3613 with Silver Medal

69. O'Sullivan Marksmanship Medal 3613 with Bronze Medal

Ju ni or D iv O ut O ve ra ll Cd t A w d

Se or D iv O ut O ve ra ll Cd t A w d

O ut st an di ng

C dt

O ffi ce r 4

El e

Di v

O ut

O ve ra ll

Cd t A w d ut st an di ng Ju ni or

D iv

C dt

Ju or ffi ce r A w ar d or D iv O ut st an di ng N

CO

A w d or D iv O ut st an di ng N

CO

A w d or D iv O ut st an di ng st Y r C dt

Aw d or D iv O ut st an di ng st Y r C dt

Aw ar d

Kn ig ht M ar ks m an sh ip

M ed al

Sp ee d M ar ks m an sh ip

M ed al

Br en na n

Sn D iv D ril l D ow n

Aw ar d

Py le

Ju ni or D iv D ril l D ow n

Aw ar d

Ar m ed D iv D ril l D ow n

Aw ar d or D iv P

LT

D ril l A w ar d or D iv P

LT

D ril l A w ar d or D iv S qu ad

D ril l A w ar d ed D iv P

LT

D ril l A w ar d or D iv S qu ad

D ril l A w ar d ed D iv S qu ad

D ril l A w ar d or D iv C ol or

G ua rd A w ar d or D iv C ol or

G ua rd A w ar d

'S ul liv an M ar ks m an sh ip

M ed al