Attachment 1_IRPOD_Sample.pdf

11/17/2023

ITEM NAMENATIONAL STOCK NUMBER

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 1RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

1.0 SCOPE

THIS IRPOD PROVIDES THE REQUIREMENTS FOR A REPAIR PART ASSEMBLY

CONSISTING OF MULTIPLE PIECES. THE REQUIREMENTS FOR EACH PIECE

PART OF THE ASSEMBLY ARE DEFINED WITHIN THIS IRPOD.

THE INDIVIDUAL PIECES OF THIS ASSEMBLY ARE LISTED BELOW.

LIFTING EYE 9072D56ITEM2

PLATE 9072D56ITEM3

SPACER 9072D56ITEM4

THUMB SCREW 9072D56ITEM1

2.0 LIST OF APPLICABLE DOCUMENTS

IF A SUPPLIER QUOTES TO A LATER REVISION OF THE DRAWING (OR CATALOG ITEM) THAN

SPECIFIED BELOW, SUBMITTAL OF QUOTE SHALL INCLUDE TWO (2) COPIES OF THE REVISED

DOCUMENT AND AN EVALUATION OF THE INTERCHANGEABILITY. THE FOLLOWING DOCUMENTS AND

CHANGE DATA ARE APPLICABLE TO THE EXTENT SPECIFIED IN THIS IRPOD, THE DRAWINGS, OR

OTHER DOCUMENTS INVOKED BY THIS IRPOD. CONTRACTING AGENCY APPROVAL IS REQUIRED TO

USE EARLIER SPECIFICATION VERSIONS THAN THOSE LISTED HEREIN, EXCEPT AS IDENTIFIED

BELOW. IF NO DOCUMENT VERSION IS LISTED, THEN ANY VERSION OF THE DOCUMENT MAY BE

USED.

RAW MATERIAL REQUIRED HEREIN MAY HAVE BEEN PROCESSED OR TESTED (FOR EXAMPLE, HEAT

TREATED OR ULTRASONICALLY TESTED) AS REQUIRED BY THE RAW MATERIAL SPECIFICATION

PRIOR TO RECEIPT OF THIS ORDER USING PREVIOUS VERSIONS OF PROCESSING OR TESTING

SPECIFICATIONS. THIS PROCESSING AND TESTING NEED NOT BE REPEATED IF:

1.IT COMPLIED WITH THE APPLICABLE REQUIREMENTS OF THE

PROCESSING/TESTING SPECIFICATION VERSIONS IN EFFECT AT THE TIME OF

THE ACTUAL PROCESSING OR TESTING AND;

2.ALL REQUIREMENTS OF THE RAW MATERIAL SPECIFICATION VERSION LISTED

HEREIN HAVE BEEN SATISFIED.

SECTION 6.0 IDENTIFIES SPECIAL REQUIREMENTS FOR SUBMITTAL OF THE PROCEDURES USED

FOR COMPLETED PROCESSING AND TESTING. ALL PROCESSING AND TESTING PERFORMED AFTER

RECEIPT OF THIS ORDER SHALL CONFORM TO THE PROCESSING/TESTING SPECIFICATION

VERSIONS LISTED HEREIN.

DOCUMENT NUMBER VERSION TITLE

FEDERAL SPECIFICATIONS

QQ-C-320 B CHROMIUM PLATING, ELECTRODEPOSITED

AMENDMENT 4 04/10/87 CHROMIUM PLATING, ELECTRODEPOSITED

+ SAE-AMS-QQ-C-320 ORIGINAL CHROMIUM PLATING, ELECTRODEPOSITED

MILITARY SPECIFICATIONS

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 2RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

MIL-PRF-23199 F PACKAGING AND PACKING REQUIREMENTS FOR

SPECIAL PURPOSE MECHANICAL COMPONENTS AND

REPAIR PARTS

FEDERAL STANDARDS

FED-STD-H28 A SCREW THREAD STANDARDS FOR FEDERAL SERVICES

MILITARY STANDARDS

+ MIL-STD-129 R MARKING FOR SHIPMENT AND STORAGE

*+ MIL-STD-792 F IDENTIFICATION MARKING REQUIREMENTS FOR

SPECIAL PURPOSE COMPONENTS

S9074-AR-GIB-010/278

ORIG. FABRICATION WELDING AND INSPECTION; AND

CASTING INSPECTION AND REPAIR FOR MACHINERY,

PIPING AND PRESSUREVESSELS IN SHIPS OF THE

UNITED STATES NAVY(REPLACES MIL-STD-278. ALL

REFERENCES TO MIL-STD-278 SHOULD BE REPLACED

WITH S9074-AR-GIB-010/278)

S9074-AQ-GIB-010/248 ORIG. WELDING AND BRAZING PROCEDURE AND

PERFORMANCE QUALIFICATION

SUPERSEDES MIL-STD-248. ALL REFER-

ENCES TO MIL-STD-248 SHALL BE

REPLACED WITH S9074-AQ-GIB-010/248.

DRAWINGS

+ 820-5349229 J CLEANLINESS REQUIREMENTS FOR REFUELING

EQUIPMENT

+ 9072D56 B WESTINGHOUSE

+ 296E600 A STANDARD TOLERANCES AND MANUFACTURING

PRACTICES

OTHERS

SAE AMS-QQ-S-763 ORIG,A,B,C OR D STEEL, CORROSION RESISTANT, BARS, WIRE,

SHAPES AND FORGINGS

IC2-SAE-AMS-QQ-S-763 STEEL, CORROSION RESISTANT, BARS, WIRE,

SHAPES AND FORGINGS

ST2258 - CAT MERRILL BROTHERS

AISI-304 INDUSTRY STANDARD

ASTM-A240 CHROMIUM AND CHROMIUM-NICKEL STAINLESS STEEL

PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS

AND FOR GENERAL APPLICATIONS

https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 3RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

AWS-A5.9 CORROSION RESISTING CHROMIUM AND

CHROMIUM-NICKEL STEEL BARE AND

COMPOSITE METAL CORED AND STRANDED

WELDING ELECTRODES AND WELDING RODS

* DOCUMENTS IDENTIFIED BY THIS SYMBOL MAY BE OBTAINED

FROM CONTRACT ISSUING AGENCY.

+ LATER VERSIONS (IE: REVISIONS, AMENDMENTS, CHANGE NOTICES

AND/OR INTERIM CHANGES) OF DOCUMENTS IDENTIFIED BY THIS SYMBOL

MAY BE USED IN THE PERFORMANCE OF THE CONTRACT. WHICHEVER

VERSION IS USED MUST BE USED IN ITS ENTIRETY. THE LATER

VERSION MAY BE IDENTIFIED AS "MIL-DTL-" OR "MIL-PRF-" AS

APPLICABLE, WHICH IS EQUIVALENT TO "MIL-#-" (WHERE # IS AN

ALPHA CHARACTER).

3.0 TECHNICAL REQUIREMENTS

RPI DET I&R TL ASSY 9072D56GP1,GP2

FINISH REQUIREMENTS SHALL BE IN ACCORDANCE WITH DWG. 296E600.

LOAD TESTING OF THIS ITEM/ASSY IS NOT REQUIRED.

THUMB SCREW 9072D56ITEM1

FINISH REQUIREMENTS SHALL BE IN ACCORDANCE WITH DWG. 296E600.

LIFTING EYE 9072D56ITEM2

MODIFY PART IN ACCORDANCE WITH DRAWING REQUIREMENTS.

FINISH REQUIREMENTS SHALL BE IN ACCORDANCE WITH DWG. 296E600.

PLATE 9072D56ITEM3

FINISH REQUIREMENTS SHALL BE IN ACCORDANCE WITH DWG. 296E600.

SPACER 9072D56ITEM4

FINISH REQUIREMENTS SHALL BE IN ACCORDANCE WITH DWG. 296E600.

3.1 MATERIAL REQUIREMENTS

RPI DET I&R TL ASSY 9072D56GP1,GP2

CLASS M MIL-STD-278

COMP. 308-L, WIRE AWS-A5.9

SUPERSEDES MIL-STD-248 S9074-AQ-GIB-010/248 ORIG.

THUMB SCREW 9072D56ITEM1

BAR,COMP.304 QQ-S-763

CHROME PLATE THREADS ONLY QQ-C-320

QQ-S-763 HAS BEEN CANCELLED. USE SAE AMS-QQ-S-763. ANY SUBMITTAL REQUIRED IN

SECTION 6 OF THIS IRPOD FOR QQ-S-763 ALSO APPLY IF SAE AMS-QQ-S-763 IS USED.

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 4RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

LIFTING EYE 9072D56ITEM2

COMP0SITION 304 AISI-304

PLATE 9072D56ITEM3

TYPE 304, ANNEALED ASTM-A240

CLASS 304, COND. A, FLAT QQ-S-763

ALTERNATE MATERIAL ASTM-A240

QQ-S-763 HAS BEEN CANCELLED. USE SAE AMS-QQ-S-763. ANY SUBMITTAL REQUIRED IN

SECTION 6 OF THIS IRPOD FOR QQ-S-763 ALSO APPLY IF SAE AMS-QQ-S-763 IS USED.

SPACER 9072D56ITEM4

BAR,COMP.304 QQ-S-763

QQ-S-763 HAS BEEN CANCELLED. USE SAE AMS-QQ-S-763. ANY SUBMITTAL REQUIRED IN

SECTION 6 OF THIS IRPOD FOR QQ-S-763 ALSO APPLY IF SAE AMS-QQ-S-763 IS USED.

3.2 MANUFACTURING AND PROCESS REQUIREMENTS

RPI DET I&R TL ASSY 9072D56GP1,GP2

ALL WELDS SHALL BE VISUALLY INSPECTED UNDER 5X MIN. MAGNI-

FICATION-ACCEPTANCE CRITERIA-NO CRACKS ALLOWED.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED OR COME

IN DIRECT CONTACT WITH HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT.

SUPERSEDES MIL-STD-278 S9074-AR-GIB-010/278 ORIG.

WELDING PROCEDURE(S) IS/ARE REQUIRED TO BE SUBMITTED

FOR APPROVAL.

DETAILED WELDING PROCEDURES IN ACCORDANCE WITH MIL-STD-278

OR ASME BOILER AND PRESSURE VESSEL CODE FOR EACH JOINT SHALL BE

SUBMITTED FOR APPROVAL PRIOR TO MANUFACTURING RELEASE. IN ADDITION

EACH WELDING PROCEDURE SHALL BE QUALIFIED IN ACCORDANCE WITH

MIL-STD-248 IF WELDING TO MIL-STD-278.

ASME WELDING PROCEDURES SHALL BE QUALIFIED IN ACCORDANCE WITH

SECTION IX OF THE ASME BOILER AND PRESSURE VESSEL CODE.

THE WAIVER FOR QUALIFICATION OF WELDS IN MIL-STD-278 SHALL BE

DISREGARDED. WELDING PROCEDURE(S) QUALIFICATION DATA SHALL BE

SUBMITTED FOR BUYER APPROVAL ALONG WITH THE APPLICABLE WELDING

PROCEDURE.

WELDING SHALL BE PERFORMED BY WELDERS QUALIFIED IN ACCORDANCE WITH

S9074-AQ-GIB-010/248 IF WELDING TO S9074-AR-GIB-010/278. WELDERS QUALIFIED TO

NAVSEA 250-1500-1 SHALL BE CONSIDERED QUALIFIED TO S9074-AQ-GIB-010/248.

THUMB SCREW 9072D56ITEM1

PARTS SHALL NOT COME IN DIRECT CONTACT WITH MERCURY OR ANY OF ITS COMPOUNDS. THE

USE OF MERCURY CONTAINING DEVICES IN THE PLATING AND PROCESSING BATHS IS

PROHIBITED.

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 5RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED OR COME

IN DIRECT CONTACT WITH HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT.

EQUIPMENT SHALL BE "REFUELING CLEAN" PER DRAWING 820-5349229.

THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28.

SUPERSEDES QQ-C-320 SAE-AMS-QQ-C-320

CLASS 2B, .0002 TO .0006 INCH THICK,

DIMENSIONS APPLY AFTER CHROME PLATING

QQ-C-320

IDENTIFICATION MARKING REQUIREMENTS SHALL BE IN ACCORDANCE WITH MIL-STD-792.

TYPE I MIL-STD-792

LIFTING EYE 9072D56ITEM2

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED OR COME

IN DIRECT CONTACT WITH HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT.

EQUIPMENT SHALL BE "REFUELING CLEAN" PER DRAWING 820-5349229.

THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28.

PLATE 9072D56ITEM3

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED OR COME

IN DIRECT CONTACT WITH HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT.

EQUIPMENT SHALL BE "REFUELING CLEAN" PER DRAWING 820-5349229.

THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28.

IDENTIFICATION MARKING REQUIREMENTS SHALL BE IN ACCORDANCE WITH MIL-STD-792.

TYPE I MIL-STD-792

SPACER 9072D56ITEM4

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED OR COME

IN DIRECT CONTACT WITH HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT.

EQUIPMENT SHALL BE "REFUELING CLEAN" PER DRAWING 820-5349229.

4.0 QUALITY ASSURANCE PROVISIONS

THUMB SCREW 9072D56ITEM1

UNLESS OTHERWISE SPECIFIED, ACCEPTABILITY OF SCREW THREADS SHALL BE DETERMINED IN

ACCORDANCE WITH FED-STD-H28/20 SYSTEM 21.

LIFTING EYE 9072D56ITEM2

UNLESS OTHERWISE SPECIFIED, ACCEPTABILITY OF SCREW THREADS SHALL BE DETERMINED IN

ACCORDANCE WITH FED-STD-H28/20 SYSTEM 21.

PLATE 9072D56ITEM3

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 6RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

UNLESS OTHERWISE SPECIFIED, ACCEPTABILITY OF SCREW THREADS SHALL BE DETERMINED IN

ACCORDANCE WITH FED-STD-H28/20 SYSTEM 21.

5.0 PREPARATION FOR DELIVERY

RPI DET I&R TL ASSY 9072D56GP1,GP2

EQUIPMENT SHALL BE HEAT SEALED IN POLYETHYLENE ENVELOPES, HAVING

EXCESS AIR EXPELLED FROM EACH ENVELOPE.

THE LABELING AND MARKING REQUIREMENTS OF MIL-PRF-23199 ARE APPLICABLE.

PACKAGING AND PACKING REQUIREMENTS -- PACKAGING AND PACKING SHALL BE TO

MIL-PRF-23199.

MARKING REQUIREMENTS--MARKING AND LABELING SHALL BE IN ACCORDANCE WITH

MIL-STD-129. BAR CODE MARKING SUITABLE FOR HAND SCANNING IS REQUIRED. THE IRPOD

HEADER MFR/PN AND THE SUPPLIER'S CAGE SHALL BE APPLIED ON THE UNIT AND

INTERMEDIATE PACK.

THUMB SCREW 9072D56ITEM1

SPECIAL MARKING REQUIREMENTS - INNER PACKAGE OF EACH PART SHALL

BE MARKED AS FOLLOWS:

"PART CLEANED TO "REFUELING CLEAN" LEVEL PER DWG. 820-5349229".

LIFTING EYE 9072D56ITEM2

SPECIAL MARKING REQUIREMENTS - INNER PACKAGE OF EACH PART SHALL

BE MARKED AS FOLLOWS:

"PART CLEANED TO "REFUELING CLEAN" LEVEL PER DWG. 820-5349229".

PLATE 9072D56ITEM3

SPECIAL MARKING REQUIREMENTS - INNER PACKAGE OF EACH PART SHALL

BE MARKED AS FOLLOWS:

"PART CLEANED TO "REFUELING CLEAN" LEVEL PER DWG. 820-5349229".

SPACER 9072D56ITEM4

SPECIAL MARKING REQUIREMENTS - INNER PACKAGE OF EACH PART SHALL

BE MARKED AS FOLLOWS:

"PART CLEANED TO "REFUELING CLEAN" LEVEL PER DWG. 820-5349229".

6.0 CONTRACT DATA REQUIREMENTS

THE SELLER MUST PROVIDE THE CONTRACTING AGENCY WITH ALL OF THE

SUBMITTALS LISTED BELOW. SUBMITTALS WHICH ARE REQUIRED BY A

SPECIFICATION, BUT WHICH ARE NOT LISTED BELOW, NEED NOT BE

SUBMITTED. ONLY THOSE SUBMITTALS LISTED BELOW ARE REQUIRED.

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 7RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

HOWEVER, IF THE SELLER CONSIDERS A REQUIRED SUBMITTAL INAPPLICABLE

TO THIS PROCUREMENT, THE SELLER MUST SUBMIT A STATEMENT JUSTIFYING

THE EXCLUSION OF THE REQUIRED SUBMITTAL.

REQUESTS FOR APPROVAL OF PROCEDURES USED PRIOR TO RECEIPT OF THIS

ORDER SHALL IDENTIFY THE PROCESSING/TESTING SPECIFICATION VERSION

APPLICABLE AND STATE THAT THE PROCESSING AND/OR TESTING WAS

PERFORMED PRIOR TO RECEIPT OF THE ORDER. IF THE PROCEDURE THAT WAS

USED IS NOT COMPLETE, TEST REPORTS, HEAT TREATMENT RECORDS, OR

OTHER DOCUMENTATION SHALL BE SUBMITTED WITH THE PROCEDURES TO

SUBSTANTIATE THAT ALL SPECIFICATION REQUIREMENTS WERE MET.

@ SUBMITTAL REQUIREMENTS IDENTIFIED BY THIS SYMBOL ARE

CONDITIONAL AND ARE REQUIRED ONLY IF APPLICABLE TO THIS

PROCUREMENT.

6.1 PROCEDURES AND REPORTS

THE SELLER SHALL PROVIDE THE FOLLOWING PROCEDURE(S) AND REPORT(S) TO THE PROCURING

ACTIVITY. CONTRACTOR PROCEDURE SUBMITTALS REQUIRED BY MATERIAL AND PROCESS

SPECIFICATIONS NEED NOT BE RESUBMITTED FOR APPROVAL EACH TIME AN ORDER IS PLACED

FOR THE SAME IRPOD ITEM TO THE SAME VERSION (I.E., REVISION, AMENDMENT, CHANGE

NOTICE OR INTERIM CHANGE) OF THE SPECIFICATION OR STANDARD INVOKED. THE SELLER

NEED ONLY SUBMIT PROOF OF THE PRIOR APPROVAL FOR THAT ITEM AND SPECIFICATION

REVISION. ACCEPTABLE PROOF OF PRIOR APPROVAL WILL CONSIST OF A COORDINATED

PROCEDURE REVIEW SYSTEM (CPRS) APPROVAL LETTER. CPRS APPROVAL DOES NOT RELIEVE

THE SELLER OF THE RESPONSIBILITY TO COMPLY WITH ALL REQUIREMENTS IMPOSED ON ANY

CURRENT AND FUTURE PURCHASE ORDERS.

IF FIRST-TIER MANUFACTURER RETESTING OF MATERIAL IS NECESSARY, USE OF BUYER

APPROVED PROCEDURES APPLICABLE TO THE SAME VERSION OF THE SPECIFICATION OR

STANDARD INVOKED ON THE IRPOD IS ACCEPTABLE IN LIEU OF OBTAINING THE RAW MATERIAL

MANUFACTURER OR MATERIAL INSPECTION AND TEST PROCEDURES FOR APPROVAL.

WHERE ALTERNATIVE SPECIFICATIONS ARE SHOWN FOR A GIVEN ITEM, ONLY THE DATA FOR THE

SPECIFICATION USED IS REQUIRED. THE SELLER SHALL SPECIFY THE FOLLOWING ON

PROCEDURE(S)/REPORT(S) REQUIRING SUBMITTAL, AS APPLICABLE, IN ORDER THAT THE

PROCEDURE/REPORT CAN BE READILY REVIEWED AGAINST THE APPROPRIATE ACCEPTANCE

CRITERIA: SPECIFICATION AND REVISION, INCLUDING AMENDMENTS, NOTICES, ETC.,

APPLICABLE PARAGRAPH OF THE SPECIFICATION, THE NAME OF THE SUBMITTAL, THE MATERIAL

CONDITIONS (I.E., MATERIAL GRADE, CLASS, TYPE, SIZE, COMPOSITION, ETC.).

6.1.1 PRIOR TO MANUFACTURE, FOR APPROVAL:

RPI DET I&R TL ASSY 9072D56GP1,GP2

MIL-STD-792

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 8RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

@EXCEPTIONS TO THE MARKING REQUIREMENT OF MIL-STD-792 THAT ARE

PER TYPE VI, SPECIAL MARKING, SHALL BE SUBMITTED FOR APPROVAL.

@FOR TYPE VIII, LASER ENGRAVING, THE QUALIFICATION PROCEDURE

FOR THE LASER ENGRAVING MACHINE AND THE DEMONSTRATION RESULTS

SHALL BE SUBMITTED FOR APPROVAL.

S9074-AQ-GIB-010/248

PROCEDURE QUALIFICATION DATA AND WELDING

PROCEDURE.

PROCEDURE QUALIFICATION DATA FOR SPECIAL WELDS

PERFORMANCE QUALIFICATION PROGRAM FOR SPECIAL

WELDS

S9074-AR-GIB-010/278

WELDING PROCEDURE

WELDING PROCEDURE QUALIFICATION TEST DATA

@RADIOGRAPHIC STANDARD SHOOTING SKETCHES.

@FABRICATION PLAN FOR WELDING TITANIUM AND

TITANIUM ALLOYS.

@ALTERNATE SAMPLING PLAN FOR IN-PROCESS AND FINAL

WELD HARDNESS FOR WELDING TITANIUM AND TITANIUM

ALLOYS.

THUMB SCREW 9072D56ITEM1

QQ-C-320

@TEST RESULTS AND PRODUCTION CONTROL INFORMATION

IF PREPRODUCTION IS SPECIFIED

MIL-STD-792

@EXCEPTIONS TO THE MARKING REQUIREMENT OF MIL-STD-792 THAT ARE

PER TYPE VI, SPECIAL MARKING, SHALL BE SUBMITTED FOR APPROVAL.

@FOR TYPE VIII, LASER ENGRAVING, THE QUALIFICATION PROCEDURE

FOR THE LASER ENGRAVING MACHINE AND THE DEMONSTRATION RESULTS

SHALL BE SUBMITTED FOR APPROVAL.

PLATE 9072D56ITEM3

MIL-STD-792

@EXCEPTIONS TO THE MARKING REQUIREMENT OF MIL-STD-792 THAT ARE

PER TYPE VI, SPECIAL MARKING, SHALL BE SUBMITTED FOR APPROVAL.

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 9RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

@FOR TYPE VIII, LASER ENGRAVING, THE QUALIFICATION PROCEDURE

FOR THE LASER ENGRAVING MACHINE AND THE DEMONSTRATION RESULTS

SHALL BE SUBMITTED FOR APPROVAL.

6.1.2 PRIOR TO USE, FOR APPROVAL:

THE SELLER SHALL NOT PERFORM THE FOLLOWING PROCEDURES(S) WITHOUT OBTAINING

SPECIFIC APPROVAL FROM THE CONTRACTING AGENCY. (IF THE SELLER REQUESTS APPROVAL

TO PERFORM THESE PROCESSES, THE SELLER SHALL SUBMIT THE PROPOSED PROCEDURE, OR

PROOF OF PRIOR APPROVAL OF THE PROPOSED PROCEDURE, WITH THE REQUEST. CPRS

APPROVAL OF THE PROCEDURE DOES NOT RELIEVE THE SELLER OF THE RESPONSIBILITY TO

REQUEST PERMISSION TO PERFORM THE PROCEDURE.):

RPI DET I&R TL ASSY 9072D56GP1,GP2

S9074-AQ-GIB-010/248

WAIVER OF QUALIFICATION TEST FOR NON-CRITICAL

WELDING

S9074-AR-GIB-010/278

@NOTIFICATION OF REPAIR WELDING TO CASTINGS.

6.1.3 PER CONTRACT DELIVERY SCHEDULE:

RPI DET I&R TL ASSY 9072D56GP1,GP2

MIL-STD-792

@TYPE II, ELECTROCHEMICAL ETCHING:

CERTIFIED TEST RESULTS SHALL BE SUBMITTED WITH EACH BATCH OR

MIX OF ELECTROLYTE TO ESTABLISH COMPLIANCE. THE CERTIFIED

TEST RESULTS SHALL ALSO IDENTIFY THE ANALYSIS METHOD UTILIZED.

THUMB SCREW 9072D56ITEM1

MIL-STD-792

@TYPE II, ELECTROCHEMICAL ETCHING:

CERTIFIED TEST RESULTS SHALL BE SUBMITTED WITH EACH BATCH OR

MIX OF ELECTROLYTE TO ESTABLISH COMPLIANCE. THE CERTIFIED

TEST RESULTS SHALL ALSO IDENTIFY THE ANALYSIS METHOD UTILIZED.

PLATE 9072D56ITEM3

MIL-STD-792

@TYPE II, ELECTROCHEMICAL ETCHING:

CERTIFIED TEST RESULTS SHALL BE SUBMITTED WITH EACH BATCH OR

MIX OF ELECTROLYTE TO ESTABLISH COMPLIANCE. THE CERTIFIED

TEST RESULTS SHALL ALSO IDENTIFY THE ANALYSIS METHOD UTILIZED.

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY K

1H 5120-01-188-1958 X3 RPI DET I&R TL ASSY 20220126123245

FLUOR MARINE PROPULSION, LLC 9072D56GP1,GP2 P

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 10RPTR01A

G22CDRE01A0058

TECHNICAL CONTACT

6.2 OTHER CONTRACT DATA REQUIREMENTS

INTENTIONALLY LEFT BLANK