Attachment 1 - BRF SOW Landing Barge With Hand Rails New Build.pdf

Beaumont Reserve Fleet

New Fabricated Landing Barge for MARAD Beaumont Reserve Fleet 40’X12’X4’

Statement of Work 02-10-2020

1. ABSTRACT:

1.1 The intent is to describe the item outlines general requirements applicable to the fabrication and delivery of (1) new steel barge 40’X12’X4’. Work is to be conducted in Accordance with ABS rules and applicable to barges of this type for the Maritime Administration, Beaumont Reserve Fleet (BRF).

2. POINT OF CONTACT:

2.1 COR Eric Welch, ACOR Trey Thibodeaux III. For technical matters Mr. Trey

Thibodeaux, MARAD Beaumont Reserve Deck Operations Supervisor

3. REFERENCES:

3.1 1 Drawing of barge (not to scale). Drawing is for reference only. Contractor to supply official drawing of barge before construction of barge begins.

4. LINE ITEM STATEMENT OF WORK AND SPECIFICATIONS:

4.1 Landing Barge

4.1.1 Overall Dimensions 40’ X 12’ X4’ box steel barge with round corners.

4.1.2 Four lifting eyes need to be attached to barge all four corners, The Lifting eyes need to be 7’ from the end of each corner of the barge. The lifting eyes shall be capable of lifting the weight of the barge and the eyelet size shall be large enough to handle an 1-1/4” anchor shackle screw pin.

4.1.3 All Steel Plate shall be ¼” thick. Deck plates, Side Plates, Bottom Plates, Headlong/Sternlong plates, Bulkheads Plates.

4.1.4 Barge Corners are radiuses with 12 inch corners.

4.1.5 Stiffeners are 4”X3”X1/4” angle iron and 8”X2”X1/4” flange plate.

4.1.6 Barge shall have 2 transverse bulkheads with a total of (3) 15”X23” flush multi-Bolt manholes.

4.1.7 Four (4) sets of double bitts of 6” X 18” SCH 80 pipe with 1-1/2” diameter Round Stock cross-arm shall be set-in bitts port to starboard.

The round stock shall by pass the pipe at least 6”. Bits shall sit on

24”X18” X1/4” plate doublers welded to the deck on each corner.

4.1.8 10 kevels 12” X1” Round Stock shall be installed 4 on each side of the barge evenly spaced one on each end of barge and center line, supported with 1/4” Plate 3 inches off the deck.

4.1.9 Install removable hand rails on one side of barge with two walk through openings and hand railing on each end of barge. Hand rails shall be 3’6” tall 2” steel pipe. Railings between stanchions shall be ¼” SS chain

Bottom chain shall be 10” from the deck center chain shall be 2’ from the deck, top chain shall be placed at the top of the stanchions. SS clips need to be placed on chain railing for removal.

4.1.10 Steel Protection includes anodes, primer coat and finish coat as follows.

4.1.10.1 Internals- Sand sweep and spray with epoxy PPG Buff Primer 4 mils dry.

4.1.10.2 Bottom and sides Headlong and Sternlong blast to white metal and spray epoxy PPG Buff primer 4 mils dry. Final coats spray PPG epoxy gray paint 2 coats 4 mils each coat.

4.1.10.3 Top side Main Deck. Blast to white metal spray epoxy PPG Buff

Primer 4 mils dry. Final coat spray PPG epoxy gray paint 2 coats 4 mils each coat. Add nonskid into final 2nd coat.

4.1.10.4 Deck Fitting and hand railing shall be blasted to white metal, primed and painted to the above specifications as the top side main deck (excluding the nonskid).

4.1.10.5 Cathodic Protection place (8) 24 lb. anodes on bottom of barge in specified locations.

5. DELIVERABLES:

5.1 Upon completion of the barges, the contractor shall furnish a scale drawing for

Barge including dimensions. (4) Four hard copies and one electronic file copy shall be submitted to the MARAD Beaumont Reserve Fleet.

5.2 Provide Mill certificates of all plates used in this construction of this barge.

5.3 The contractor shall Provide (1) complete set of approve drawings prior to construction of the barge. And (1) additional copy of any drawing that is revised during the construction.

5.4 The contractor shall provide copies of welder’s certificates upon MARAD request.

5.5 The contractor is responsible for all labor and materials and any overtime labor costs.

5.6 The contractor/vendor shall make deliveries 8am to 3:30pm Monday-Thursday, 8am to 2:30pm on Fridays, No deliveries on national holidays.

5.7 Landing barge shall be completed 60 day after award of contract.

6. GENERAL REQUIREMENTS:

6.1 The contractor shall provide all labor, equipment, material, engineering and structural calculations to accomplish the specification(s).

6.2 All welding shall be performed by a certified welder.

6.3 All steel used shall be of the original size as it was new or size listed in the statement of work or drawings if they are available for the repair

6.4 The contractor shall obtain all applicable Insurance’s, Marine Chemist certificates and permits required by law to accomplish the specification(s).

6.5 Specification(s) are estimates given for identification and general guidance only.

6.6 Material or equipment identified in these specifications may be with equivalent products with the Beaumont Reserve Fleet Representative’s approval.

6.7 The contractor shall dispose of all waste as per local, state and federal regulations. Copies of disposal documentation, if required, shall be delivered to the Environmental Officer.

6.8 Deliver the completed barge and ready for use, to the Beaumont Reserve Fleet

2600 Amoco Road Beaumont Texas 77705.

7. TESTING:

7.1 The contractor shall conduct a pressure test of all exterior welds using a standard pressure test. After the pressure test, the interior of the barge shall be inspected to verify water tightness of the barge.

7.2 Prior to delivery, the contractor shall launch the barge to determine if the barge floats with zero trim and/or list. The contract shall correct any trim or list using solid ballast.

8. GOVERNMENT FURNISHED MATERIALS:

8.1 None

9. GOVERNMENT FURNISHED EQUIPMENT:

8.1 None

BEAUMONT RESERVE FLEET

For:Drawn by: Eric Welch Date: Scale:

BEAUMONT RESERVE FLEET

12-8-2016 Not To Scale PAGE 1 OF 2

Title: Landing Barge

TOP VIEW

DECK PLAN

12’

40’

2’10” 3’-6”

¼” SS CHAIN LINKS

2” Steel Pipe

21/4” SS Socket Typical Handrail

Stantion

¼” PLATE

Transvers Bulkhead

SIDE VIEW

BEAUMONT RESERVE FLEET

For:Drawn by: Eric Welch Date: Scale:

BEAUMONT RESERVE FLEET

12-08-16 Not To Scale PAGE 2 OF 2

Title: Landing Barge

4’

END VIEW

4’

12’

6” 12”

40’

12’

40’

Bottom View Anode location

8) 23# WELD ON ANODES¼” PLATE

4’

12’

TYPICAL BULKHEAD

¼” PLATE

BEAUMONT RESERVE FLEET

For:Drawn by: Eric Welch Date: Scale:

BEAUMONT RESERVE FLEET

12-8-2016 Not To Scale PAGE 3 OF 3

Title: Landing Barge