Attachment 0002 - AED Requirments.pdf

02/13/2020

M701PRID 145CS114-2Part Number

1680-01-120-7641NSN CH-47FSystem

ELECTRO-MECHANICAL ACTUATORNomenclature

YAdequate DMWR Available?

DMWR-55-1680-289DMWR ID

07/19/2013DMWR Date

DMWR Chg #

NPre-Award Survey Recommended?

NCorrelation Performance Study Required ? NPVA Recommended?

Proper orientation of the lower rod end (Item 24, Figure 3-1), part of assembly (21, Figure 3-1), is a critical characteristic. The lower rod end has a flat side and a tabbed side (anti-rotation lugs). The rod end shall be installed with the flat side facing the motor side of the actuator (tabs facing away from the motor). Refer to table 2-2 of DMWR for CSI CC.

See DMWR 55-1680-289 paragraph 3-7 and Table 3-1.2 for Inspection Requirements.

See DMWR 55-1680-289 paragraph 4-1 for Final Test Procedures.

See DMWR 55-1680-289 paragraph 5-7 for In-Process and Acceptance Inspection Requirements.

The overhaul facility is responsible for acquisition, maintenance, calibration, and disposition of all Test, Measurement and Diagnostic Equipment (TMDE). TMDE shall be maintained and controlled in accordance with MIL-I-45607, AMCOM-R-702-2 or NCSL Z540.3. Calibration documents for all TMDE shall be traceable to the National Institute of Standards of Technology (NIST).

Identify Any Special Processes, Test Procedures, and/or Instructions

YCritical Safety Item?

There are no emerging airworthiness issues, no issues related to ECPs affecting the CSI status, and no concerns over reliability/durability for the CH-47F Electro-Mechanical Actuator at the time of this review.

Special Airworthiness Considerations

FCDD-AMA-M AED Sustainment has verified the CSI/NST status through the ARISE CIM on 14 Nov 2019 and the NHA is CSI and NST. The subcomponents are CSI and NST. Engineering testing Fatigue, Endurance, and Interchange are not required for overhaul. Updated NHA table in ARISE CIM. The manufacturer part number is 541604-9-1. DEM

Other Requirements / Comments

If the item is not a CSI and no adequate DMWR is available, approved sources, if any, are listed by CAGE as follows:

NSpecial Post-Contract Award Requirements?

The Prime or OEM is required to submit a Frozen Plan 30 days after contract award to Engineering Directorate (ED) and Aviation Engineering Directorate (AED). The Frozen Plan will be reviewed and require approval by ED and AED prior to government acceptance of contract deliverable assets.

Other Requirements / Comments (Part II)

The applicable DMWR contains detailed procedures regarding IUID requirements for this component. These procedures can be found in MEOs D2454, D2455, and D2456.

Other Requirements / Comments (Part III)

SRD-AMA-M-A/W-Sustainment has re-verified the CSI/NST status through the ARISE CIM on 3 Feb 2020 and the NHA is CSI and NST. The subcomponents are CSI and NST. Engineering testing Fatigue, Endurance, and Interchange are not required for overhaul. No changes made. DEM

Other Requirements / Comments (Part IV)

YDoes QE-STD-2 Apply?

Y

Additional CSI Requirements

CSI Contains CSI Replacement Parts? YEngineering Testing Required?

The Contractor shall flow down the Critical Characteristics and QE-STD-1 to all Suppliers of CSIs.

The solicitation/RFP shall require that all proposals/responses include a special tooling and test equipment section that addresses the contractor's plan to meet all government special tooling and test equipment requirements with either:

1. Physical possession of the required tools, 2. Confirmed requisitions for the required tools, 3. Confirmed arrangements for subcontracting the processes requiring the special tools, or 4. Specific plans describing their technical approach to develop equivalent tools.

RStatus

YTDPL?

01/01/1987Approved Date

M&O AED REQUIREMENTS DATA

Commerciality Determination

Commercial Item? N NBest Commercial Practice Acceptable?

02/13/2020

M701PRID 145CS114-2Part Number

1680-01-120-7641NSN CH-47FSystem

D1116

D1733

D2176

D2299

D2421

D2454

D2455

D2456

D2488

D2489

D2490

D2508

D2528

D2564

D2567

D2568

D2575

See DMWR 55-1680-289 Table 2-1 and Table 2-1.1 for test and special tools and equipment.

Critical Tools and Test and Inspection Equipment Requiring AED Approval for Substitutes

MEOs Required for Competitive Contract?

Special Post-Contract Award Requirements

Other Requirements / Comments (Part V)

RStatus

Correlation Performance Study Requirements