Attachment 0001 Drum Dumper and Auger System.docx
DOCX document 28 KB Posted
- Attached to
- Drum Dumper and Auger System Federal contract opportunity
- Solicitation number
- W52P1J-22-P-0000-006004
About this file
This notice requests market research information to support the Army Contracting Command - Rock Island in determining contractor interest and capability to provide Flexicon brand drum dumper and auger conveyor systems to the McAlester Army Ammunition Plant in McAlester, Oklahoma. Specifically, the notice seeks four FlexiCon Drum Dumper Model DDT-C2SE-P048-X units and two each of the FlexiCon Auger Conveyor System Model HPD1-S36-X units, as well as related accessories outlined in Attachment 0001, to fully outfit the required bulk handling equipment and conveyor system. Responders should provide their company name, CAGE code, and ability to fulfill this requirement by emailing Sheila Peters at sheila.k.peters2.civ@army.mil by May 31, 2022. The NAICS code is 333922 for Conveyor & Conveying Equipment Manufacturing and the size standard is 500 employees. The PSC is 3910 for Conveyors. This notice serves planning purposes only and does not constitute a solicitation, proposal request, or commitment to award a contract.
View the file
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Specific Requirements – Attachment 0001
This section provides specific requirements for the drum dumper systems requested.
1. TIP-TITE drum dumper
a. Qty (4) FlexiCon model DDT-C2SE-P048-X
b. 750 LB capacity with material discharge height from 36” to 48”
c. To accommodate standard 55-gallon drums ranging from 30” to 39” high and an outer diameter of 22” to 24”
d. Discharge cone equipped with neoprene gasket for the drum lip seal for static control
e. Hydraulic powered system with pneumatic motor
f. Elevates and rotates drum to 60 degrees passed horizontal
g. 10” diameter pneumatic material discharge slide gate valve
h. 10” diameter Series 486 Posi-Flate inflatable seated butterfly material discharge valve
i. Pneumatic controls mounted in a NEMA 4 enclosure
j. Control panel
k. Gravity roller conveyor for container loading
l. Operational air supply requirements are limited to 45 cfm at 80 psi
m. 316 stainless steel product contact surfaces
n. Citric passivation
2. Gravity roller conveyor
a. Qty (4) FlexiCon model RCGF-C060N-X
b. Able to be bolted to floor
c. 36” long with 2.5” diameter rollers on 4.5” centers
d. Operational width of 28”
e. 1,000 LB max pallet load
This section provides specific requirements for the single auger conveyor systems requested.
3. Type “D” floor hopper:
a. Qty (2) FlexiCon model HPD1-S36-X
b. 8 cubic foot measured capacity
c. 36” square x 38” high
d. 55 degree conveyor take off angle
e. Centering rod
f. 316L stainless steel construction
g. Grounding stud
h. Citric passivation
4. Solid hopper cover:
a. Qty (2) FlexiCon model CVS-S36-X
b. Bolted to hopper flange
c. Gasketed inlet port to mate with drum dumper
d. Vent port with filter sock
e. Viton gasket for static control
f. 316L stainless steel construction
g. Grounding stud
h. Citric passivation
5. Mounting pad for pneumatic turbine vibrator:
a. Qty (2) FlexiCon model VPP-S-X
b. 316L stainless steel construction
c. Includes citric passivation
6. Pneumatic turbine vibrator assembly:
a. Qty (2) FlexiCon model VBP-E-X
b. 115 VAC NEMA 7/9 solenoid valve, filter, regulator, gauge
c. Requires 60-80 PSI air supply
d. Controlled by existing control panel
e. Meets Class I, Division I, Groups B, C and D and Class II , Division I , Groups E, F and G.
7. Capacitive type proximity level switch:
a. Qty (2) FlexiCon model LSP-I-X
b. Intrinsically safe sensor with panel mounted relay amplifier
c. 115 VAC operating voltage
d. 316L stainless steel construction
e. Controlled by existing control panel
f. Low level location
g. Must meet Class I, Division I, Groups B, C and D and Class II , Division I , Groups E, F and G
8. 20’ long conveyor:
a. Qty (2) FlexiCon model UTRH-S045-020-X
b. 1450 FLEXICON conveyor
c. 4 ½” O.D. 316L stainless steel outer tubing
d. Heavy duty round wire configuration spiral
e. Discharge box to include static control neoprene gasket
f. Mates to a 7.5 HP drive assembly
g. 316L stainless steel construction
h. Grounding stud
i. Stainless steel intermediate support couplings
j. Citric passivation
9. Gear drive assembly:
a. Qty (2) FlexiCon model DRP-05018E-05-X
b. ii. 7.5 HP, 1725 RPM, 3 phase, 60 hz motor
c. iii. Explosion proof with parallel shaft gear reduction unit
d. iv. Must meet Class 1, Div 1, Grp D and Class II, Div 1, Grp E,F and G
e. 316L stainless steel mounting bracket
10. Transition discharge adapter:
a. Qty (2) FlexiCon model DCT1-S3-X
b. ii. Converts from rectangular flanged conveyor outlet to round port
c. iii. Facilitates connection to flexible boots or valves
d. iv. Neoprene gasket for static control
e. v. 316L stainless steel construction
f. Grounding stud
g. Citric passivation
11. Capacitive type proximity level switch
a. Qty (2) FlexiCon model LSP-I-X
b. ii. Intrinsically safe sensor with panel mounted relay amplifier
c. iii. 115 VAC operating voltage
d. iv. 316L stainless steel construction
e. v. Located in transfer
f. vi. Must meet Class I, Division I, Groups B, C and D and Class II , Division I , Groups E, F and G
12. Static dissipative down spouting
a. Qty (2) 2 feet FlexiCon model FS-S06-X
b. 6” diameter flexible
c. One set of clamps
d. Citric passivation
File details come from the government source that posted it. Updated .