Attachment 0001 - Drawing 7274730.pdf

D

C

B

A

D

C

B

A

8 7 6 5 4 3 12

DESIGN ACTIVITY

SIZE CAGE CODE

SCALE UNIT WT.

DRAWN BY DATE(YEAR-MO-DA)

CHECKER ENGINEER

ENGINEER QUALITY ENGINEER

DRAWING APPROVAL

DESIGN APPROVALMATL ENGR MODELED BY

CONTRACT NUMBER

CONTRACTOR

SHEET

DRAWING SIZE D

TOLERANCES ON ANGLES �#� �$�

2 PLACE DECIMALS �#�

3 PLACE DECIMALS �#�

FORMAT: D_TACOM_ENG_1_0 12345678

DWG NO.

.5080 .0001

CHAMFER BOTH ENDS

RADIUS OPTIONAL

.030 .005

30�$�2�$�

REVISIONS

APPROVEDDATE(YEAR-MO-DA)DESCRIPTIONDRAWING REV

RLV2014-06-05

REDRAWN WITH CHANGE,

NOR L14S3038 / 2014-05-28

F

AG2015-01-15NOR L15S3002 / 2015-01-15G

1 OF 10.284 2/1

727473019205D

WEAR CHECK

US ARMY

SPRINGFIELD ARMORY

SPRINGFIELD, MASSACHUSETTS

2014-05-28M. CROSSON

2014-05-28J. WINDHAM

S. HUNTER

B. SULZBACHA. GOMEZ

1954-12-16T. HERUM

APPLICATION

USED ONNEXT ASSY

7265156

7266131

PMIC

MECHANICAL

PROPERTIES

YP

TS

EL2

RA

BH

RH T.HERUM

THIRD ANGLE PROJECTION

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

DO NOT SCALE DRAWING

PART NO. 7274730

THIS DRAWING WAS GENERATED FROM A SOLID MODEL

AND IS CAD MAINTAINED. CHANGES SHALL BE

INCORPORATED BY THE DESIGN ACTIVITY.

NSN 5220-00-317-2503

MARK DATA IN BLOCK BELOW ON

GAGE IN POSITION SHOWN

7274730

PRIME CONTRACTOR - [ ]

WEAR CHECK FOR 7274725

CURRENT DESIGN ACTIVITY CAGE CODE 19200

US ARMY

ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER

PICATINNY ARSENAL, NEW JERSEY 07806-5000

LABEL OR OTHER MARKING

NOTE 7

NOTE 10

DISTRIBUTION STATEMENT A.

APPROVED FOR PUBLIC RELEASE;

DISTRIBUTION IS UNLIMITED.

NOTES:

1. APPLICABLE SPECIFICATIONS/STANDARDS:

A. ASME Y14.100-2004

B. ASME Y14.5-2009

C. MIL-W-13855

D. MIL-G-10944

E. ASME B46.1

F. GAGE BLANKS - COMMERCIAL STD CS-8

2. MATERIAL: ALLOY TOOL STEEL A2 OR 01 PER ASTM A681

3. HARDNESS: ROCKWELL C61 TO C66 OR EQUIVALENT

4. BREAK ALL EDGES 1/32�#�1/64.

5. SURFACE FINISH: EXCEPT AS NOTED

6. PROTECTIVE FINISH ON ALL NON-WORKING SURFACES ONLY:

FINISH 3.3.2 OF MIL-STD-171. MAY BE APPLIED PRIOR TO

FINAL MACHINING OF WORKING SURFACES.

7. LASER-ETCH ALL MARKING EXCEPT AS NOTED.

ALL MARKINGS, WHETHER LASER ETCHINGS OR LABELS, SHALL

BE PERMANENT AND LEGIBLE PER MIL-STD-130.

8. NEWLY-PRODUCED GAGES SHALL MEET ALL REQUIREMENTS

OF THE DRAWING. ANNUAL FIELD RE-CALIBRATION

REQUIREMENTS ARE NOTED.

9. MAJOR QAP CHARACTERISTIC SHALL BE LISTED ON

THE GAGE RECORD CARD IN THE BLOCK ENTITLED

"REQUIRED COMPONENT DIMENSION." THE DIMENSION SHALL

BE MEASURED AND THE MEASUREMENT RECORDED IN THE BLOCK

ENTITLED "ACTUAL GAGE DIMENSIONS." EACH CARD SHALL BE

SIGNED AND DATED BY THE CONTRACTOR CERTIFYING THAT THE

GAGE COMPLIES WITH THE REQUIRED DIMENSION SPECIFIED

ON THE GAGE DRAWING AND SHALL BE PLACED IN THE PACKAGING

WITH THE GAGE. EACH PACKAGE ASSEMBLY SHALL CONTAIN ONE GAGE

AND THE GAGE RECORD CARD SPECIFIC TO THAT GAGE.

THE GAGE RECORD CARD MUST BE COMPLETED AT THE TIME OF

ACCEPTANCE BY THE ACCEPTANCE POINT (ORIGIN OR DESTINATION)

IDENTIFIED IN TE CONTRACT.

10. THE LABEL OR OTHER MARKING SHALL CONTAIN A LINEAR BAR CODE

(MACHINE-READABLE INFORMATION), ALONG WITH THE HUMAN-READABLE

INTERPRETATION, REPRESENTING THE GAGE IDENTIFICATION NUMBER.

A DUPLICATE LABEL OR OTHER MARKING SHALL APPEAR ON THE

GAGE RECORD CARD IN THE BLOCK ENTITLED "IDENTIFICATION NO."

EACH GAGE IDENTIFICATION NUMBER SHALL BE CHOSEN/ASSIGNED BY

THE GOVERNMENT.

11. QUALITY ASSURANCE PROVISION REQUIREMENTS PER DRAWING

NUMBER 12993884 APPLY.

MARK DATA

SECTION A-A

KNURLING

ISO VIEW

Y

MATERIAL

Y

PROTECTIVE FINISH

II

V

WORKMANSHIP

II

V

PROTECTIVE FINISH MISSING OR NONUNIFORM

II

V

INCORRECT, MISSING OR IMPROPERLY PLACED MARKING

V

GAGE RECORD CARD (DA FORM 3023)

III

C

SURFACE FINISH OF WORKING SURFACES

Z

HARDNESS

Y

V

MARKING PER MIL-STD-130

C