Atch 01 PWS USATA.pdf

USATA-NG-0012-21

Attachment 01

PERFORMANCE WORK STATEMENT

FOR REPAIR AND CALIBRATION OF Eight (8) ANRITSU Models

1.0 GENERAL: The U.S. Army Test, Measurement and Diagnostic Equipment Activity (USATA) has a requirement to acquire commercial repair and International Organization for Standardization (ISO) 17025 accredited calibration of eight (8) Anritsu Models, manufactured by the Anritsu Corporation of Morgan Hill, CA.

2.0 CONTRACTOR TASKS.

2.1 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 114810, reports that the unit needs to repair the fails level accuracy and flatness at 10 MHz and 15 MHz. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.2 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 114620, reports that the unit fails calibration of the power level accuracy at 34GHz and above. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.3 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 115001, reports that the unit was damaged during transport and the item will not operate correctly to be tested. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.4 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 120710, reports that the unit has a front panel broken and right frame bent. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.5 A preliminary evaluation of the Anritsu Model MG3695BOPT2C, Serial Number 094411, reports that the unit TI fails self-test requires manufacture diagnosis and limited parts availability. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.6 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 120502, reports that the unit needs a YIG loop oscillator repair and calibration. The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.7 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 120510, reports that the unit TI fails the power level accuracy test at multiple frequencies at the lower dB levels (i.e. -85, -90). The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

USATA NG-0012-21

Attachment 01

2.8 A preliminary evaluation of the Anritsu Model MG3694C/2B/5, Serial Number 114321, reports that the unit TI fails the power level accuracy test at multiple frequencies at the lower dB levels (i.e. -85, -90). The potential vendor will provide repair and calibration to the unit based on the preliminary evaluation and provide ISO accredited calibration.

2.9 The contractor shall replace defective parts, as required, with original equipment manufacturer parts only. The contractor shall apply applicable factory-proprietary software and firmware updates at intervals required by the original equipment manufacturer. The contractor shall strictly comply with turn-around-time to repair as stated in Section B of the contract.

2.10 The contractor shall not provide any repair or other services outside the scope of this contract without authorization from the government Contracting Officer listed at page 1 of the contract. The contractor shall not hold equipment at the contractor’s facility outside of the contract period of performance stated in Section B of the contract without authorization from the Contracting Officer.

3.0 GOVERNMENT TASKS.

3.1 The government shall be responsible for shipment of all units from the USATA facility to the contractor’s facility at government expense. All units shall be shipped to the contractor’s facility not later than 48 hours (excluding weekends and holidays) after receipt of notice of contract award.

3.2 The U.S. Army TMDE Activity, Redstone Arsenal, AL (Acceptance DODAAC:

W80RA6) shall be responsible for receiving, inspection and acceptance in DFAS Wide Area Workflow (WAWF) for the unit.

4.0 PLACE OF PERFORMANCE. All performance shall take place at the Contractor’s facilities.

5.0 PERIOD OF PERFORMANCE. All action shall be 90 Days ARO.

6.0 GOVERNMENT-FURNISHED EQUIPMENT. None.

7.0 QUALITY REQUIREMENTS. OEM or equivalent parts are recommend.