ASTM B 221 Specification for Aluminum_MOD.pdf
PDF 133 KB Posted
- Attached to
- ANGLE, STRUCTURAL
- Solicitation number
- SPMYM223Q1992
About this file
This document outlines material ordering data for aluminum extrusions according to ASTM B221 specifications. It provides dimensions of 3" x 3" x 1/4" thick aluminum bars in alloy 5086 with a H111 temper. The order requires a certified mill test report including chemical and mechanical test data, and preservation and packaging per MIL-STD-129 for commercial shipment. Marking and identification must follow ASTM B666/B666M. The related federal contract opportunity is for structural angles through the Defense Logistics Agency Land and Maritime under solicitation number SPMYM223Q1992.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| SOLICITATION NOTICE_SPMYM223Q1992.pdf | ||
| CERTIFIED MILL TEST REPORT CDRL DI MISC 82386.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
MATERIAL ORDERING DATA
ASTM B221
IDN: N4523A 3214-7900
ICN: KO: KOI:
Paragraph 4.1 Ordering data
4.1.1 ASTM B221, STANDARD SPECIFICATION FOR ALUMINUM AND
ALUMINUM-ALLOY EXTRUDED BARS, RODS, WIRE, PROFILES, AND TUBES,
dated 01 SEP 2021.
4.1.2 Quantity in pieces or pounds:
4.1.3 Alloy: 5086 (see Section 7 and Table 1),
4.1.4 Temper: H111 (Section 8 and Table 2),
4.1.5 Nominal cross-sectional dimensions as follows:
4.1.5.1 For rod and round wire—diameter:
4.1.5.2 For square-cornered bar and wire—depth and width:
4.1.5.3 For sharp-cornered hexagonal or octagonal bar and wire—distance across flats:
4.1.5.4 For round tube—outside or inside diameter and wall thickness:
4.1.5.5 For square or sharp-cornered tube other than round—distance across flats and wall thickness:3" X 3" X 1/4" THK
4.1.5.6 For round-cornered bars, profiles, tube other than round, square, rectangular, hexagonal, or octagonal with sharp corners—drawing required:
4.1.6 Length: 20 Foot Length
4.2 Additionally, orders to this specification shall include the following information when required by the purchaser:
4.2.1 Is solution treatment at the press unacceptable? : N/A
4.2.2 Is heat treatment in accordance with Practice B918 required (9.4)? : N/A
4.2.3 Is ultrasonic inspection required (Section 17 Table 3)? : Not Required.
4.2.4 Is inspection or witness of inspection and tests by the purchaser’s representative required prior to material shipment (Section 18)? : Not Required.
4.2.5 Is certification required (Section 22)? : Yes, Certified Mill Test Report (CMTR) see additional data requirements.
MATERIAL ORDERING DATA
ASTM B221
4.2.6 Is marking for identification required in accordance with Practice B666/B666M, section 20? : Required.
4.2.7 Does Practice B660 apply? Yes.
If so, provide the levels of preservation, packaging, and packing required:
Commercial. Marking for shipment shall be in accordance with MIL-STD-129.
4.2.8 Requirements for tensile property and dimensional tolerance for sizes not specifically covered (8.1.3 and 15.1.1): N/A
4.2.9 Is Titanium and Zirconium algorithm allowed as shown in Table 1, Footnote H, when ordering 2014 or 2024? N/A
4.2.10 Is Titanium and Zirconium algorithm allowed as shown in Table 1, Footnote T, when ordering 7075? N/A
Additional Data Requirements:
CMTR shall include at a minimum actual data of chemical and mechanical tests.
Qualitative results of nondestructive tests and other inspections or tests shall be recorded on the certificate as applicable.
Prepared By: J. SUTLIFF Code: C/244.4
File details come from the government source that posted it. Updated .