APPENDIX I.pdf

General Specifications

User Interface

Dimensions

13.50 in (W) x 11.54 in (L) x 5.75 in (D)

34.3 cm (W) x 29.3 cm (L) x 14.6 cm (D)

Display Size 30.5 cm (12 in)

Weight 7.71 kg (17 lbs) Base Unit

Internal Battery 2.5+ Hour at Full Backlight

Rugged 30 G Shock, MIL-STD 28800F Class 3

Direct Input Power 50 W Continuous, 125 W Cyclical

Internal Wideband RF Power Sensor (Part Number 139442 Only)

500 W, 4% Accuracy

Record & Playback Digital Audio Quality

Quick Presets Ultra-Fast Test Setup

Frequency Lists Tx Frequency, Tx Level; Rx Frequency

“Fast Stack” Instant Access to Multiple Meters

Tracking Generator

VSWR, Return Loss, Distance-to-Fault, Tuning Duplexers

LMR System Support

P25 P25 Phase II DMR NXDN™ dPMR ARIB T98 AM/FM PTC

Analog Duplex Operation

1 GHz RF Generator (AM / FM) 1 GHz Receiver (AM / FM)

Channel Analyzer Oscilloscope

DMM Audio Level Meter

Distortion Meter SINAD Meter

RF Power Meter Audio Frequency Counter

DTMF Encode / Decode DCS Encode / Decode

RF Frequency Error Meter In-band Power Meter (RSSI)

RF Generator

Port Input Protection

GEN Port +20 dBm (Input Power Alarm Typical)

T/R Port +52 dBm CW (Input Power Alarm Typical)

T/R Port >+90°C (Temperature Alarm Typical)

Frequency

Range 2 MHz to 1000 MHz <2 MHz to 100 kHz Usable Range

Output Level

Range T/R Port: -50 to -125 dBm ANT Port: -30 to -90 dBm GEN Port: -5 to -65 dBm

Accuracy ±2 dB; ±1.5 dB (Typ)

Resolution 1 dB

0.1 dB (0 to -6 relative to selected level with 0.1 dB Step On)

Port VSWR

ANT Port <1.5:1 Typical

GEN Port <1.5:1 Typical

T/R Port <1.2:1

SSB Phase Noise -90 dBc/Hz at 20 kHz offset

-95 dBc/Hz at 1 GHz at 20 kHz offset, Typical

Spurious Harmonics: -30 dBc, -42 dBc Typical

Non-Harmonics: -40dBc, -50 dBc Typical (±20 kHz offset from carrier; 0 to 1 GHz)

Residual FM <20 Hz rms in 300 Hz to 3 kHz BW

<4 Hz rms, Typical <100 MHz

<6 Hz rms, Typical <800 MHz

<11 Hz rms, Typical >800 MHz

Residual AM <0.5% rms in 300 Hz to 3 kHz BW

RF Generator Modulation RF Generator Modulation Type

Analog FM and AM

Digital P25 (C4FM, H-CPM, H-DQPSK), DMR, dPMR, ARIB T98, NXDN, PTC

DTMF FM and AM

DCS FM and AM

Two-Tone Sequential

FM and AM

Tone Remote FM and AM

Tone Sequential FM and AM

CTCSS FM, and AM using modulation generators

Accuracy Same as timebase

Resolution 1 Hz

RF Generator (continued)

APPENDIX I

COMMUNICATION SYSTEM ANALYZER

RF Generator Modulation (continued) FM Modulation - Internal (GEN 1, GEN 2)

Modulation Frequency Range

Range: 0 Hz to 20 kHz

Resolution: 0.1 Hz

Accuracy: Timebase ±2 Hz

FM Deviation Range: Off 0 Hz to 100 kHz (GEN 1 and GEN 2 Selectable)

Total Harmonic Distortion:

3% (1000 Hz rate, >2 kHz Deviation, 300 Hz

- 3 kHz BP filter)

Resolution: 1 Hz

Accuracy: ±5% at 1 kHz rate; 2 kHz to 50 kHz deviation (±1% typical) ±10% at 150 Hz to 3 kHz rate; 2 kHz to 50 kHz deviation

FM Modulation - External (MIC, AUDIO IN)

Microphone In

Alternate MIC Configurations

MIC Connector Pins

Range 1: 2-15 mVrms (8 mVrmw Typical)

Pin 2-OPEN, Pin 6-GND

Range 2: 35-350 mVrms (100 mVrms Typical)

Pine 2-GND, Pin 6-OPEN

(Range 2 enables a nominal 3 Vdc Bias Voltage)

Range 3: 2-32 mVrms (20 mVrms Typical)

Pin 2-OPEN, Pin 6-OPEN

MIC Frequency Range 300 Hz to 3 kHz

MIC Level Off, 0 Hz to 80 kHz

MIC Modulation Accuracy

±20% (300 Hz to 1.2 kHz) ±30% (>1.2 kHz)

MIC Slope Positive voltage yields positive deviation

Audio In

AUD IN Input Range: 30 V, 3V

AUD IN Switchable Loads

3 V Range: 150 ohms, 600 ohms, 1K ohms, High Z 30 V Range: High Z

AUD IN Input Levels 3 V Range: 0.05 to 3.2 Vrms 30 V Range: 3 Vrms - 30 Vrms

AUD IN 300 Hz to 5 kHz

AUD IN 3 V Range: 1 kHz/35 mVrms Typical 30 V Range: 1 kHz/350 mVrms Typical

AUD IN Positive voltage yields positive deviation

AM Modulation - Internal (GEN 1, GEN 2)

Modulation Frequency Range

Range 0 Hz to 20 kHz

Resolution 0.1 Hz

Accuracy Timebase ±2 Hz

Range Off, 0 to 100% (GEN1 and GEN2 Selectable)

Resolution 0.1%

Total Harmonics Distortion

3% (20% to 90% mod, 1000 Hz rate, 300 Hz to 3 kHz BP filter)

Modulation Accuracy ±5% setting @ 1 kHz rate ±10% setting @ 150 Hz to 5 kHz rate 10% to 90% modulation

AM Modulation - External (MIC, AUDIO IN)

Microphone In

Alternate MIC Configurations MIC Connector Pins

Range 1: 2-15 mVrms (8 mVrms Typical)

Pin 2-OPEN, Pin 6-GND

Range 2: 35-350 mVrms (100 mVrms Typical)

Pin 2-GND, Pin 6-OPEN (Range 2 enables a nominal 3 Vdc bias voltage)

Range 3: 2-32 mVrms (20 mVrms Typical)

Pin 2-OPEN, Pin 6-GND

MIC Frequency Range 300 Hz to 3 kHz

MIC Modulation 0% to 80%

MIC Modulation Accuracy ±20% (300 Hz to 1.2 kHz) ±30% (>1.2 kHz)

Audio In

AUD IN Input Range: 30 V, 3 V

AUD IN Switchable Loads 3 V Range: 150 ohm, 600 ohms, 1 K ohms, High Z 30V Range: High Z

AUD IN Input Levels 3 V Range: 0.05 to 3.2 Vrms

30 V Range: 3 Vrms - 30 Vrms

AUD IN AM Frequency Range 300 Hz to 5 kHz

AUD IN Level Sensitivity 3 V Range: 1% / 35 mVrms Typical (High Z Load)

30 V Range: 1% / 350 Vrms Typical (High Z Load)

AFGEN 1 and AFGEN 2

Frequency

Range 0.0 Hz to 20.0 kHz

Resolution 0.1 Hz

Accuracy Timebase ±2 Hz

Output Level

Audio Out Port Impedance

<1 ohm

Audio Level Out 0 Vrms to 1.57 Vrms

Resolution 0.001 Vrms

Accuracy ±10%; >100 mVrms, 30 Hz to 3 kHz

Distortion <3% (1 kHz rate, sine 300 Hz to 3 kHz)

RF Receiver Port Input Protection

ANT Port +20 dBm (Input Power Alarm Typical)

T/R Port +52 dBm CW

T/R Port >+90°C (Temperature Alarm Typical)

Frequency

Range 2 MHz to 1000 MHz <2 MHz to 100 kHz Usable Range

Accuracy Same as Timebase

Resolution 1 Hz

RF Receiver (continued) Input Amplitude

Sensitivity ANT: -80 dBm, typical 10 dB SINAD (-110 dBm with preamp) T/R: -40 dBm, typical, 10 dB SINAD

Minimum Level Receiver Measurements

ANT: -60 dBm Preamp off, -80 dBm Preamp On, RF Error Meter T/R: -20 dBm Preamp Off, -40 dBm Preamp ON, RF Error Meter

DEMOD Meters ANT: Distortion, SINAD, Modulation, AF Counter T/R: Modulation, Distortion, SINAD, AF Counter

Maximum Input Level Receiver Measurements

ANT: +10 dBm (Auto, Preamp off) T/R: +47 dBm CW, FM +41 dBm AM

Receiver Demodulation Types

AM, FM, DMR, dPMR, ARIB T98, NXDN, P25 (C4FM, H-CPM, H-DQPSK), PTC

AM Modulation - External (MIC, AUDIO IN)

IF Bandwidth FM: 5 kHz, 6.25 kHz, 8.33 kHz, 10 kHz,

12.5 kHz, 25 kHz, 30 kHz, 100 kHz, 300 kHz

AM: 5 kHz, 6.25 kHz, 8.33 kHz, 10 kHz,

12.5 kHz, 25 kHz, 30 kHz

Audio Filters Bandwidth

FM: C-WT BP, CCITT BP, NONE, 15 kHz LP, 300 Hz LP, 300 Hz HP, 5 kHz LP, 300 Hz to 5 kHz BP, 300 Hz to 3 kHz BP, 300 Hz to 20 kHz BP, 3 kHz LP

AM: C-WT BP, CCITT BP, NONE, 15 kHz LP,

0.3 kHz LP, 0.3 kHz HP, 5 kHz LP, 300 Hz to 5 kHz BP, 300 Hz to 3 kHz BP, 0.3 kHz to 20 kHz BP, 3 kHz LP

Audio Output, Level Sensitivity

FM: 3 Vrms/kHz Dev/IF BW (kHz, ±15%) AM: 7 mVrms/% AM, ±15%

LO EMISSIONS <-50 dBc

RF Frequency Error Meter

Units Hz, PPM

Range ±200 kHz, ±1000 PPM

Resolution 1 Hz

Accuracy Timebase ±1 Hz

RSSI (Receive Signal Strength Indicator) RF Power Within Receiver IF Bandwidth

Units dBm, Watts, microWatts

Range -120 dBm to +60 dBm

RF Level Range

T/R Port (preamp off): -50 dBm to +47 dBm ANT Port (preamp off): -90 dBm to +10 dBm ANT Port (preamp on): -110 dBm to -10 dBm

Resolution 0.01 dBm

Accuracy ±3 dB; (1.5 Typical) Normalized

Ext Attenuation -50 to +50 dB, 0.01 dB resolution

RF Power Meter (Broadband RF Power Into T/R Port)

Maximum Input Level

50 Watts continuous, +25°C, ±10°C

125 Watts Cyclical (Max “ON” of 30 sec and Min “OFF” for 90 sec) for power levels >50 Watts

Alarms +49 dBm (Input RF Power Alarm) >+90°C (+194°F) (Temperature Alarm)

Meter Range +20 to +53 dBm

Meter Floor 0.10 W/+20 dBm

Measurement Modes Average, Maximum, Minimum, Peak

Averaging Range 1 to 99

Display Units Watts, dBm

Resolution 0.01 W, 0.1 dBm

Accuracy 10% of reading, (6% Typical)

Ext Attenuation -50 to +50 dB, 0.01 dB resolution

FM Deviation Meter

Range 500 Hz to ±100 kHz

Meter Type Peak+, Peak-, (Peak-Peak)/2, RMS

Resolution 0.1 Hz

Accuracy ±10% of reading, 500 Hz to 100 kHz Deviation ±5% of reading, 1 kHz to 10 kHz Deviation (150 Hz to 1 kHz rate) ±3% of reading, 1 kHz to 10 kHz Deviation (1 kHz to 1.5 kHz rate)

AM Percent Meter

Range 5% to 100%

Modes Peak+, Peak-, (Peak-Peak)/2, RMS

Resolution 0.001%

Accuracy ±5% of reading, 1 kHz rate 30% to 90% modulation, 3 kHz LPF

SINAD Meter

Measurement Sources AUD IN, Demod

DEMOD

FM: >2 kHz Deviation (IF BW set appropriately for received modulation BW) AM: >25% Modulation (IF BW set appropriately for received modulation BW)

AUDIO IN Port

Frequency Range 300 Hz to 10 kHz

Input Level 3 V (Audio Config setup): 0.9 Vp-p to 9 Vp-p 30 V (Audio Config setup): 9 Vp-p to 90 Vp-p

Audio Frequency Notch 1 kHz

Reading Range 0 dB to 60 dB

Resolution 0.001 dB

Accuracy ±1.5 dB, reading >8 dB, <40 dB

Distortion Meter

Measurement Sources AUD IN, Demod

DEMOD FM: >2 kHz Deviation (IF BW set appropriately for received modulation BW)

AM: >25% Modulation (IF BW set appropriately for received modulation BW)

AUDIO IN Port

Frequency Range 300 Hz to 10 kHz

Input Level 3 V (Audio Config setup): 0.9 Vp-p to 9 Vp-p 30 V (Audio Config setup): 9 Vp-p to 90 Vp-p

Audio Frequency Notch 1 kHz

Reading Range 0% to 100%

Resolution 0.001%

Accuracy ±10% of reading +0.1% Distortion, >1% to <20%

Audio Frequency Counter

Measurement Sources AUD IN, Demod

DEMOD FM: 15 Hz to 20 kHz Rate (IF BW set appropriately for received modulation BW)

AM: 100 Hz to 10 kHz Rate (IF BW set appropriately for received modulation BW)

AUDIO IN Port

Frequency Range 300 Hz to 20 kHz

Input Level 3 V (Audio Config setup): 28 mVp-p to 9 Vp-p

30 V (Audio Config setup): 280 mVp-p to 90 Vp-p

Frequency Range 15 Hz to 20 kHz

Resolution 0.1 Hz

Accuracy ±1 Hz

Audio Frequency Level Meter

Measurement Sources AUD IN, SCOPE

Input Range

AUD IN Range 3 V, 30 V

Scope Range 2 VDC, 40 VDC

Frequency Range 200 Hz to <5 kHz

Load Selection

Scope High Z

AUD IN

3 V Input Range: High Z, 150 ohms, 600 ohms, 1 K ohms 30 V Input Range: 10 K

Input Level

AUD IN Port 3 V Range: 10 mV rms to 3.2 V rms 30 V Range: 1 V rms to 30 V rms

Scope Port 2.0 VDC Range: 10 mV rms to 1 V rms 40 VDC Range: 1 V rms to 28.28 V rms

Display Unit Resolution

Volts: 0.001 V mV: 0.001 mV dBuV: 0.001 dBuV dBm: 0.001 dBm Watts: 0.001 W

Accuracy ±5% AUD IN Port

P25 Measurements Modulation Fidelity

Range 0 to 10%

Resolution 0.1%

Accuracy <5.0% of reading (2.5 to 10%)

Symbol Deviation

Range 1620 to 1980 Hz

Resolution 0.1 Hz

Accuracy ±10 Hz (1620 to 1980 Hz)

Symbol Clock Error

Range ±12 ppm

Resolution 0.01 ppm

Accuracy 1 ppm (±0.0048 Hz)

DMR Measurements FSK Error

Range 0 to 10%

Resolution 0.1%

Accuracy <5.0% of reading (2.5 to 10%)

Symbol Deviation

Range 1745 to 2140 Hz

Resolution 0.1 Hz

Accuracy ±10 Hz

Symbol Clock Error

Range ±12 ppm

Resolution 0.01 ppm

Accuracy ±1 ppm (±0.0048 Hz)

Oscilloscope Source SCOPE, AUD IN, Demod

Bandwidth 5 kHz

Input Impedance

Scope Input 2.0 V Range: 53 K ohm 40 V Range: 1 M ohm

Audio I/O Input 3 V Range: 150 ohm, 600 ohm, 1 k ohm, High Z 30 V Range: 10 k ohm

Coupling Scope: AC, DC and GND Audio In: AC only FM Internal Demod: DC AM Internal Demod: AC

Oscilloscope (continued) Vertical Range

Scope, Audio In 10 mV to 10 V-div in a 1, 2, 5 sequence

FM Internal Demodulation 0.1 kHz to 50 kHz/div in a 1, 2, 5 sequence

AM Internal Demodulation 5, 10, 20, 50%/div

Vertical Accuracy 10% of full scale (DC to 5 kHz)

Horizontal Sweep 0.5 ms/div to 0.1 sec/div

Horizontal Accuracy 3% of full scale

Trigger Type Internal (Auto, Normal)

Trigger Level Variable on vertical scale

Markers Two markers Displays vertical measurement (Voltage, kHz, % modulation) Displays Delta in time between markers

Channel Analyzer Range 2 MHz to 1 GHz

Span 10 kHz to 5 MHz (1, 2, 5 steps)

Windows Hanning, Flat Top, Rectangle

Vertical Scale 2, 5, 10, 15, 20 dB/div

Marker Bandwidth 1 kHz to 5 MHz (1, 2, 5 steps)

Marker Offset ±1 kHz to ±1/2 Span (1, 2, 5 steps)

Power Band Width (PdB) Accuracy ±3 dB typical (30 dB signal to noise)

Noise Floor -123 dBm (preamp off) -140 dBm (preamp on) (span 100 kHz), typical

Wide Analyzer 10 kHz to 50 MHz in 1, 2, 5 sequence

Digital Multimeter (DMM)

AC/DC Voltmeter

Range 200 mV, 2 V, 20 V, 200 V, 2000 V, Auto (150 VAC RMS to VDC MAX input, Category II)

Resolution 3.5 digits (2000 counts)

Accuracy DC: ±1% FS ±1 count AC: ±5% FS ±1 count +25 mV

AC/DC Ammeter

Range 200 mA, 2 A, 20 A, Auto (20 A range uses optional shunt connected to Voltmeter)

Maximum Open Circuit Input Voltage

30 V RMS referenced to COMMON or EARTH GROUND, Cateogry I

Resolution 3.5 digits (2000 counts)

Accuracy DC: ±5% FS ±1 count AC: ±5% FS ±1 count

AC Volts Frequency Range 50 Hz to 10 kHz

Ohmeter

Range 200 ohms, 2 k ohms, 20 k ohms, 200 k ohms, 2 M ohms, 20 M ohms, Auto

Resolution 3.5 digits (2000 counts)

Accuracy ±5% FS ±1 count

In-Line Power Meter

RF Measurement Type Average Power, Peak, Burst, Crest, CCDF

Frequency Range 25 MHz to 1 GHz

Power Range 500 mW to 500 W Average

13.3 W to 1300 W Peak

Insertion VSWR <1.05

Insertion Loss <0.05 dB

Directivity 29 dB up to 50 MHz 30 dB from 51 to 1000 MHz

Average Power

Average Forward Power Range 500 mV to 200 W Average

Peak/Average Ratio, Max 12 dB

Accuracy, Average Forward Power

±4% of reading +166 mW Maximum accuracy performance at 25°C (±10°C) (77°F ±50°F)

Return Loss 0 to 23 dB

VSWR 1.15 to 99.9

Burst Average Power

Burst Average Power Range 13.5 W to 500 W Average

Burst Width 1 µs to 5 ms

Repetitions Rate Min 200 Hz

Duty Cycle (D) 0.001 to 1.0 (D=Burst Width/Period)

Accuracy, Burst Average Power ±6% of reading +0.116/D mW

Peak Envelope Power

Peak Envelope Power Range 13.3 to 1300 W

Peak Envelope Power Accuracy

Burst width >200 µs: ±7% of reading, +0.70 W 1 µs <burst width <200 µs: ±10% of reading, +1.40 W

0.5 µs <burst width <1 µs: ±15% of reading, +1.40 W Burst width <0.5 µs: ±20% of reading, +1.40 W

Crest Factor

Measurement Range 500 mW to 300 W, 13.3 W Minimum Peak

Accuracy, Crest Factor Linear Sum of Peak and Average Power Accuracies

Complementary Cumulative Distribution Function (CCDF)

Measurement Range 0.1 to 100%

Threshold Measurement Range 13.5 to 500 W

Measurement Uncertainty ±0.2%

Level Set Accuracy As Peak Envelope, Power Accuracy +2.0%

Speaker Output

Speaker On or Off

Output

75 dBa min at 0.5 m, 600 to 1800 Hz, max volume Speaker disconnects when headphones installed.

Volume Control

Level Range Scale 0 to 100

Timebase

Temperature Stability ±0.15 ppm at -20° C to 70° C (-4°F to 158°F)

Aging 0.5 ppm/First Year

0.3 ppm/After First Year

External 10 MHz Reference Input

External Input Frequency Range 10 MHz ±150 Hz

External Input Level -10 dBm to +10 dBm

Max Input +15 dBm

Freq-Flex (Externally Referenced Timebase Calibration)

Input Frequency Range 2 MHz to 1000 MHz

Reference Input Port T/R: >-20 dBm Antenna: >-40 dBm

Freq-Flex Accuracy <0.5 Hz from external source applied + Stability + Aging

Example: 10 MHz External Input, after Freq-Flex = ±0.5Hz to external input. 10 MHz ±0.5 Hz = 0.05 ppm + Stability + Aging

I/O Connections

T/R Connector Type: N-Type Female

ANT Connector Type: N-Type Female

GEN Connector Type: N-Type Female

Scope Connector Type: BNC Female

AUD IN Connector Type: BNC Female

AUD OUT Connector Type: BNC Female

Headphone Jack: 3.5 mm Jack

USB Connectors (Qty 3) Type: USB Type A

External 10 MHz Reference Input: BNC Female

Ethernet Connector Type: RJ45

DC Power in Connector: 2-position 2.5 mm Jack

GND Connector: Banana

DMM (Qty 3): Banana (Optional)

IN (In-Line Power Meter): N-Type Female (Optional)

OUT (In-Line Power Meter): N-Type Female (Optional)

Front Panel Indicators

SYS Indicator Green: 88XX Power On/Awake Mode

Blue: 88XX Sleep Mode

Red: 88XX Shutting Down

Green/Red Flashing: Battery Temperature >60°C (>140°F)

Green Flashing: Battery Life <5%

BAT Indicator Green: Battery at full charge

Amber: Battery is charging

Microphone Connector

6 PIN MIC CONNECTOR

Pin Number Name Characteristic

1 GROUND

2 SPEAKER+ Output 75 dBa min at 0.5 m, 600 to 1800 Hz, max volume

3 PTT Input GND, open (with internal pullup)

4 Mic/Audio Input 0 to 30 mVrms, voiced tone (whistle), 300 Hz to 3 kHz

5 MICSEL 1 GND, open with pullup

GND = 3 V DC bias (active Mic) and Mic audio gain of 2 Open = 0 V DC bias and Mic audio gain of 3

6 MICSEL 2 GND, open with pullup

Environmental/Physical

Overall Dimensions 34.3 cm (W) x 29.3 cm (L) x 14.6 cm (D)

13.5 in (W), 11.54 in (L) x 5.75 in (D)

Weight 17 lbs (No hardware options installed)

Temperature Storage: -40°C to +71°C (-40°F to +159.8°F), MIL-PRF-28800F, Class 3 Note: Battery must not be subjected to temperatures below -20° C, nor above +60° C

8800SX Operation

DC Operation -20°C to +50°C (-4°F to 122°F)

AC/DC Power Supply See AC Input Power Section

Battery Operation -20°C to approximately +50°C 1, 2 (-4°F to approximately +122°F)

Relative Humidity

Operation 5 to 95%, tested in accordance with MIL- PRF-28800F, Class 3

Altitude

Battery Only Operation 4,600 m (MIL-PRF-28800F, Class 3)

AC Power Supply Operation 3,048 m (MIL-PRF-28800F, Class 3)

Shock, Functional

Operation 30 G Shock (Functional Shock), tested in accordance with MIL-PRF-28800F, Class 3

Vibration

Operation 5 to 500 Hz random vibrations, tested in accordance with MIL-PRF-28800F, Class 3

Bench Handling

Operation Tested in accordance with MIL-PRF-28800F, Class 3

1: Battery operation over temperature based on actual temperature rise of battery and instrument usage 2: Battery must not be subjected to temperature below -20° C nor above +60° C

Environmental/Physical (continued) Compliance

EMC

Emissions and Immunity

MIL-PRF-28800F, Class 3 EN61326-1, Class A

EN61000-3-2

EN61000-3-3

Safety UL 61018-1

EN61010-1

CSA C22.2 No 61010-1

Reliability 20,000 hours at 25°C (77°F)

AC Input Power (AC to DC Converter/Charger Unit)

AC Input Voltage Range 100 to 250 VAC, 3 A max., 47 Hz - 63 Hz

AC Input Voltage Fluctuation Less than 10% of the nominal input voltage

Transient Overvoltage According to Installation Category II

Usage Environment Indoor use, Maximum Relative Humidity 80% for temperatures up to 31°C (87.8°F) decreasing linearly to 50% RH at +40°C (104°F), Installation Category II, Pollution degree 2

Operating Temperature 0°C to +40°C (32°F to 104°F)

Storage Temperature -20°C to +85°C (-4°F to +185°F)

EMI EN55022 Class B, EN61000-3-2, Class D

Safety UL 1950, CSA 22.2 No 234 and No 950, IEC

950/EN 60950

DC Input Power

Voltage Range 11 to 24 VDC

Maximum Power 55 W, 65 W charging Optional Battery

Typical Power 30 W

Fused 5 A, 32 VDC, Type F

Supplemental Items

Battery Type Lithium Ion (Li Ion) battery pack Note: Battery must not be subjected to temperatures below -20°C, nor above +60°C

Battery Operation Time

100% Backlight 2 1/2 hours typical

Minimum Backlight (still viewable) 3 hours typical

Battery Charge Time 4 hours Unit Power Off Typical

4 hours Unit Powered On Typical Note: Battery to be charged at temperatures between 0°C and +45°C (32°F and +113°F)

Charge dead battery (<10% capacity) for 20 minutes before operation on external DC power

Ordering Information

Versions and Options

Order Number Description

142820 8800SX Radio Test Set

Standard Accessories

Fuse, 5 A, 32 V, Mini Blade

Power Supply

AC Power Cord

AC Power Cord - China

AC Power Cord - Europe

AC Power Cord - UK

Adapter, N(m) to BNC(f), Qty 3

Front Cover

Internal Battery

139942 8800SX Radio Test Set with Internal Wideband Power Sensor

Standard Accessories

Internal Bird 5017D Wideband Power Sensor

Fuse, 5 A, 32 V, Mini Blade

Power Supply

AC Power Cord

AC Power Cord - China

AC Power Cord - Europe

AC Power Cord - UK

Adapter, N(m) to BNC(f), Qty 3

Front Cover

Internal Battery

Options

113334 8800OPT01 DMR

140215 8800OPT06 DMR Repeater Test (Requires Opt01)

113335 8800OPT02 dPMR

113336 8800OPT03 NXDN

113337 8800OPT04 P25 Conventional

138895 8800OPT05 P25 Phase II (Requires Opt04)

113338 8800OPT09 ARIB T98

142131 8800OPT162 TETRA Base Station

113339 8800OPT10 Tracking Generator

113340 8800OPT11 Occupied Bandwidth

113342 8800OPT13 External Bird 5017D Wideband Power Sensor Support (Requires Power Sensor)

113343 8800OPT14 PTC

113344 8800OPT15 AAR Channel Plan

139836 8800OPT20 R&S Power Sensor Support (NRT-Z14)

139837 8800OPT21 SINAD Selectable Notch Filters

139838 8800OPT22 SNR Meter

143910 8800OPT23 SX Function Access

Auto-Test and Alignments

DMR Radios

138528 8800OPT104 Motorola MOTOTRBO Series Auto- Test and Alignment Software (Requires Opt01)

139314 8800OPT108 Hytera DMR Series Auto-Test and Alignment Software (Requires Opt01 and Opt22)

139313 8800OPT109 Hytera DMR Repeater Auto-Test and Alignment Software (Requires Opt01 and Opt108)

141179 8800OPT113 Tait DMR Series Auto-Test ONLY (Requires OPT01)

NXDN Radios

138525 8800OPT101 Kenwood NEXEDGE Series Auto-Test and Alignment Software (Requires Opt03)

P25 Radios

139319 8800OPT114 BK Technologies KNG Series Auto-Test and Alignment Software (Requires Opt04)

139320 8800OPT115 EF Johnson Viking Series Auto-Test and Alignment Software (Requires Opt04)

139317 8800OPT111 L3Harris P25 Series Auto-Test and Alignment Software (Requires Opt04)

141180 8800OPT117 L3Harris XL Series Auto-Test and Alignment Software (Requires Opt04)

138526 8800OPT102 Kenwood 5x20 Series Auto-Test and Alignment Software (Requires Opt04)

140913 8800OPT118 Kenwood Viking 5/6/7000 Series Auto-Test and Alignment Software (Requires Opt04)

138527 8800OPT103 Motorola APX Series Auto-Test and Alignment Software (Requires Opt04)

140868 8800OPT128 Motorola APX 8000 Auto-Test and Alignment Software (Requires Opt04 and Opt103)

140900 8800OPT129 Motorola APX “B” Auto-Test and Alignment Software (Requires Opt04 and Opt103)

139315 8800OPT105 Motorola ASTRO® 25 XTS® / XTL™ Auto-Test and Alignment Software (Requires Opt04)

8800OPT130 8800OPT130 Motorola APX NEXT™ Series Auto- Test and Alignment Software (Requires Opt04 and Opt103)

139318 8800OPT112 Tait P25 Series Auto-Test ONLY (Requires OPT04)

Multi-Protocol Radios

141178 8800OPT107 Kenwood NX-3000 / 5000 Series Auto-Test and Alignment Software (Requires Opt01, Opt03, or Opt04 depending on radio digital technology selected)

Languages

113356 8800OPT306 Arabic

113350 8800OPT300 Chinese (Simplified)

113351 8800OPT301 Chinese (Traditional)

113361 8800OPT311 French

113360 8800OPT310 German

139625 8800OPT312 Italian

113359 8800OPT309 Japanese

113355 8800OPT305 Korean

113354 8800OPT304 Malay / Indonesian

113357 8800OPT307 Polish

113358 8800OPT308 Russian

113352 8800OPT302 Spanish

Optional Accessories

114477 Case, Hard Transit

114478 Case, Soft-Sided Carrying

82556 Attenuator (6 dB / 150 W), 1.5 GHz

140227 Attenuator (40 dB / 2 W), 18 GHz Type N

67076 Battery, Spare, Internal

114479 8800 External Battery Charger

114348 8800 Precision DTF / VSWR Accessory Kit (Requires Opt10)

92793 External Bird 5017D Wideband Power Sensor (Requires Opt13)

114312 8800 Rackmount Kit

112861 8800 Microphone

114475 8800 Antenna Kit

62404 8800 DC Power Cord / Cigarette Adapter

63936 AC24009 DMM Test Leads

112277 10 Amp Current Shunt, 0.01 Ohm

67411 Scope Probe Kit

141707 8800 Balanced to Unbalanced Audio Adapter

63351 RF Cable for AutoAlignment (COAX ASSY, RG223,36.0,BNC,M,ST / BNC,M,ST)

140742 NEON Tracking Unit w/belt clip

140747 NEON Signal Mapper Package - Tracking Unit, Software, and 1 Year License

140748 NEON Signal Mapper Package - Tracking Unit, Software, and 2 Year License

140749 NEON Signal Mapper Package - Tracking Unit, Software, and 3 Year License

141586 NEON Signal Mapper Package - Tracking Unit, Software, and 5 Year License

63927 Survey Technologies Inc (STI) Site Survey Package (Software & GPS Antenna)

Extended Warranties

114481 8800 1 Year Extended Hardware Warranty + ANSI No-Cert Calibrations

114483 8800 1 Year Extended Hardware Warranty + Certified Calibrations

114482 8800 3 Year Extended Hardware Warranty + ANSI No-Cert Calibrations

114484 8800 3 Year Extended Hardware Warranty + Certified Calibrations

Calibration Certificates

138313 8800 Calibration Certificate (ISO 9001)