- ADDITIONAL INFORMATION PERTINENT TO REQUIREMENT.docx

ADDITIONAL INFORMATION PERTINENT TO REQUIREMENT

TESTING REQUIREMENTS

CIRCUIT SPECIFICATIONS:

CONUS NO JUMBO FRAME ETHERNET VENDOR WILL PERFORM ACCEPTANCE TESTING IN ACCORDANCE WITH EITHER RFC-6815 OR ITU-T Y.1564.

VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS IAW ITU-T.Y.1564 SPECIFICALLY, FRAME SIZES OF 64,128,256,512,1024,1280 AND 1518 BYTES MUST BE USED.

THE TEST MUST VERIFY LENGTH OF RECEIVED FRAMES, INDICATE NUMBER OF FRAMES DROPPED, NUMBER OF FRAMES RECEIVED OUT OF ORDER, AND DUPLICATE FRAMES.

TESTS MUST BE BI-DIRECTIONAL USING THE SAME DATA RATE IN EACH DIRECTION. BURST TESTS MUST BE RUN TO DETERMINE MINIMUM INTERVAL BETWEEN FRAMES THAT CAN BE PROCESSED WITHOUT FRAME LOSS.

A THROUGHPUT TEST IS REQUIRED INDICATING THE FASTEST RATE AT WHICH TEST FRAMES CAN BE TRANSMITTED WITHOUT FRAME LOSS. A SEPARATE THROUGHPUT TEST MUST BE RUN WITH FRAMES ADDRESSED TO THE HARDWARE BROADCAST ADDRESS CONSTITUTING AT LEAST 1% OF THE TEST STREAM AND BE EVENLY DISTRIBUTED THROUGHOUT THE TEST.

A LATENCY TEST MUST BE RUN FOR A PERIOD OF NO LESS THAN 120 SECONDS, AND REPEATED NO LESS THAT 20 TIMES. THE TEST STREAM FOR THE LATENCY TEST SHOULD BE RUN AT THE THROUGHPUT RATE FOR CORRESPONDING FRAME SIZES FROM THE THROUGHPUT TEST. END TO END LATENCY WILL BE CALCULATED AS THE AVERAGE OVER THE 20 TEST RUNS. FRAME LOSS RATE TESTS SHOULD BE RUN AT THE FRAME RATE CORRESPONDING TO THE MAXIMUM FRAME RATE, AND REDUCED BY 10% INTERVALS UNTIL THERE ARE AT LEAST TWO CONSECUTIVE RUNS IN WHICH NO FRAMES ARE LOST.THROUGHPUT TEST RESULTS: PASSING RATE 100% FOR ALL FRAME BYTE SIZES EXERCISED. FRAME LOSS RATE (%) RESULTS: FRAME LOSS RATE LESS THAN 0.01% FOR ALL FRAME BYTE SIZES EXERCISED. LATENCY WILL BE MEASURED WILL BE ACCORDING TO THE FOLLOWING MAXIMUM TRANSMISSION DELAY FOR ANY CIRCUIT UP TO 500 MILES AIR-MILES IN LENGTH SHALL BE NO GREATER THAN 13MS ONE-WAY AND ANY POINT-TO-POINT CIRCUIT LONGER THAN 500 AIR-MILES SHALL BE NO GREATER THAN 50MS ONE WAY WITHIN THE 48 CONTINENTAL STATES. ANY APS SWITCHOVER SHALL TAKE LESS THAN 50 MILLISECONDS MONTHLY AVAILABILITY SHALL BE NO LESS THAN 99.5%.

CONNECTION APPROVAL PROCESS STATEMENT:

1. GOVERNMENT MANDATES THAT REQUIRE CONNECTION REGISTRATION IAW THE DISN CONNECTION PROCESS GUIDE (CPG): 1.(A) CJCSI 6211.02D PARA 2.C.(D) 1.(B) DODI 8010.01 PARA 1.2.C(4) 1.(C) DISN CONNECTION PROCESS GUIDE (CPG) HTTPS://CYBER.MIL/CONNECT/

2. CONNECTION APPROVAL IS REQUIRED PRIOR TO DISN PORT(S) BEING CONNECTED AND ACTIVATED FOR CUSTOMER USE.

3. NAVIGATE TO PROPER CONNECTION DATABASE (SNAP OR SGS) AND REGISTER CONNECTION UNDER APPROPRIATE SERVICE MODULE.

(A) FOR NIPR/SIPR OR NIPR/SIPR VPN SERVICE: SELECT NIPR/SIPR MODULE UTILIZING CONNECTION TYPE DOD, NON-DOD, OR CONTRACTOR (NON-DOD)

(B) FOR VPN: SELECT VPN MODULE SETTING TYPE OF VPN REGISTRATION AS "VPN MEMBER" AND ROUTER INTERFACE CONNECTION TYPE AS "VIRTUAL"

(C) FOR OR DEDICATED POINT TO POINT VIRTUALS: SELECT NIPR MODULE SETTING THE CONNECTION TYPE AS "TRANSPORT".

4. FAILURE TO REGISTER AND OBTAIN AN IATC/ATC FOR YOUR CONNECTION WILL DELAY SERVICE ACTIVATION.

5. IF YOU ARE UNABLE TO ACCESS THE SNAP/SGS WEBSITES OR REQUIRE SPECIFIC GUIDANCE FOR UNIQUE CUSTOMER ISSUES, PLEASE CONTACT THE CONNECTION APPROVAL OFFICE (CAO), AT C301-225-2900/301-225-2901, DSN 312-375-2900/2901 OR SEND AN EMAIL TO DISA.MEADE.RE.MBX.UCAO@MAIL.MIL OR DISA.MEADE.RE.MBX.CCAO@MAIL.MIL. U. IMPLEMENTATION ASSISTANCE: IMPLEMENTATION ASSISTANCE: FOR SERVICE ACTIVATION INQUIRIES/SCHEDULING/ASSISTANCE, NAVIGATE TO THE DISA GLOBAL SERVICE ACTIVATIONS CUSTOMER ACCESS PORTAL: HTTPS://DISA.DEPS.MIL/DISA/COP/GSM-O/BACKBONE/CUSTOMER%20ACCESS%2 0SITE/SITEPAGES/SAM%20CUSTOMER%20HOMEPAGE.ASPX, OR CONTACT DSN 312-418-8627, CMCL 001-618-418-8627. FOR EMAIL SUPPORT, PLEASE CONTACT THE APPROPRIATE TEAM BELOW: DEDICATED/NIPRNET/SIPRNET/VPN SERVICE ACTIVATIONS: EMAIL: DISA.SCOTT.GLOBAL.MBX.RF-CIRCUIT-ACTIVATIONS@MAIL.MIL SIPRNET ACCESS MIGRATION (SAM) PROJECTS (D508, D710, D806, D910): EMAIL: DISA.SCOTT.GLOBAL.MBX.IMPACT-TEAM@MAIL.MIL FOR ALL OTHER PROJECT RELATED EFFORTS: EMAIL:DISA.SCOTT.GLOBAL.MBX.RF-CIRCUIT-ACTIVATIONS@MAIL.MIL DISN BACKBONE ACTIVATIONS: EMAIL: DISA.SCOTT.GLOBAL.MBX.CASA-INFRASTRUCTURE-INTEGRATION-LEAS E-BB-T@MAIL.MIL

IMPLEMENTATION ASSISTANCE CONTINUED: FOR CIRCUIT INSTALLATION ASSISTANCE WITH THE COMMERCIAL LEASED PATH, CONTACT DCP COMMERCIAL ACTIVATION TEAM (CAT) AT D312-850-0820, C614-692-0820. W. UNSATISFACTORY SERVICE REPORTING INSTRUCTIONS: FOR UNSATISFACTORY SERVICE OR TO REPORT EQUIPMENT AND/OR CIRCUIT PROBLEMS INVOLVING DISA PROVIDED TRANSPORT AND/OR EQUIPMENT, PLEASE CONTACT THE DIS A GLOBAL SERVICE DESK (GSD) TOLL FREE NUMBER IS 1-844-347-2457 (1 -844-DISA HLP) OPTION 2, COML 1-614-692-0032 OPTION 2, DSN 312-85 0-0032 OPTION 2 OR EMAIL: DISA.GSD.INFRASTRUCTURE@MAIL.MIL.