Addendum 1.pdf

COMMONWEALTH OF KENTUCKY

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

INVITATION TO BID NO: RFB-111-26

FOR: KYTC D-11 Bell Co Structure Renovation

Kentucky Transportation Cabinet Bell County, Kentucky

DATE: November 12, 2025

RFB-785-2600000194

ADDENDUM NO. One (1)

BIDDER SHALL CONFORM TO THE FOLLOWING CHANGES AS SAME SHALL BECOME BINDING

UPON THE CONTRACT TO BE ISSUED IN RESPONSE TO THIS INVITATION TO BID.

Item 1: Refer to attached addendum for all additions, deletions, and/or changes to specifications and/or drawings.

END OF ADDENDUM

Invitation to Bid No. RFB-111-26 For: KYTC D-11 Bell Co Structure Renovation

Kentucky Transportation Cabinet Bell County, Kentucky

Janis Wilhoite, Statewide Procurement Analyst II Division of Engineering and Contract Administration

KYTC D-11 Bell County Structure Renovation 609-CBY1-Z001-A79 November 11, 2025

Kesler Simpson Architects, LLC 3728 Willow Ridge Road, Lexington, KY 40514 859-523-4324 www.ksa-llc.com

KYTC D-11 Bell County Structure Renovation

ADDENDUM #1

This Addendum forms a part of the Contract and clarifies, corrects, or modifies the original Bid Documents. Acknowledge receipt of this addendum in the space provided on the bid form. Failure to do so may subject bidder to disqualification.

This addendum contains twelve (12) sheets including this sheet.

A. See attached revised Door Schedule from Sheet A-4 to clarify door types and hardware sets.

B. See attached new spec section 087100 Door Hardware.

DOOR SCHEDULE

MARK

DOOR FRAME DETAILS

FIRE

RATING HARDWARE COMMENTS

SIZE

TYPE MATERIAL FINISH GLASS TYPE MATERIAL FINISH HEAD JAMBWIDTH HEIGHT THICK

101 3'-0" 7'-0" 1 3/4" HG HM PAINT IN/SAFE 1 HM PAINT - - -

101A 3'-0" 7'-0" 1 3/4" 316 HM PAINT SAFE 1 HM PAINT - - 1

102 3'-0" 7'-0" 1 3/4" HG HM PAINT IN/SAFE 1 HM PAINT - - - 1

102A 3'-0" 7'-0" 1 3/4" 316 HM PAINT SAFE 1 HM PAINT - - 1

103 3'-0" 7'-0" 1 3/4" F HM PAINT - 1 HM PAINT - - - 1

104 3'-0" 7'-0" 1 3/4" F HM PAINT - 1 HM PAINT - - - 1

105 3'-0" 7'-0" 1 3/4" F HM PAINT - 1 HM PAINT - - - 1

106 3'-0" 7'-0" 1 3/4" F HM PAINT - 1 HM PAINT - - - 1

HG

HG

KYTC D-11 BELL COUNTY STRUCTURE RENOVATION 609-CBY1-Z001-A79

DOOR HARDWARE 087100 - 1

SECTION 087100 – DOOR HARDWARE

PART 1 - GENERAL

0.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

0.2 SUMMARY

A. Section Includes:

1. Door Hardware

B. Related Sections:

1. Section 079000 - Joint Sealers – exterior thresholds.

2. Section 081000 - Metal Doors and Frames.

C. Specific Omissions: Hardware for the following is specified or indicated elsewhere.

1. Toilet accessories, including grab bars.

2. Installation.

3. Rough hardware.

1.3 REFERENCES

A. Use date of standard in effect as of Bid date.

B. American National Standards Institute – ANSI 156.18 – Materials and Finishes.

C. ICC/ANSI A117.1 - 1998 – Specifications for making buildings and facilities usable by physi-cally handicapped people.

D. ADA – Americans with Disabilities Act of 1990

E. BHMA – Builders Hardware Manufacturers Association

F. DHI – Door and Hardware Institute

G. NFPA – National Fire Protection Association

1. NFPA 80 – Fire Doors and Windows

2. NFPA 101 – Life Safety Code

3. NFPA 105 – Smoke and Draft Control Door Assemblies

4. NFPA 252 – Fire Tests of Door Assemblies

H. UL – Underwriters Laboratories

1. UL10B – Fire Tests of Door Assemblies as amended to incorporate positive pres-sure testing.

DOOR HARDWARE 087100 - 2

2. UL 305 – Panic Hardware

I. WHI – Warnock Hersey Incorporated

J. SDI – Steel Door Institute

K. AWI – Architectural Woodwork Institute

L. NAAMM – National Association of Architectural Metal Manufacturers

1.4 SUBMITTALS & SUBSTITUTIONS

A Schedules:

The finish hardware supplier shall, upon award of the contract, furnish ONE ELECTRON- IC PDF COPY of a completely detailed schedule of finish hardware in the Door and Hardware Institute’s Sequence and Format for approval within 30 days. Hardware schedule to be complete with Title page, Door Index/Keying Schedule and Manufactures legend. After “Approval” provide ONE CORRECTED ELECTRONIC PDF COPY, unless otherwise requested, of the corrected, revised and approved schedule for field use, dis-tribution and files. Provide one (1) copy complete with Catalog Cuts, marked “Installers Copy” and deliver it to the job site.

B. Product Data:

Provide a catalog cut, clearly marked and identified, illustrating and describing each product included in the hardware schedule. Formulate these catalog cuts into sets and include a set with each copy of the hardware schedule submitted.

C. Samples:

If so requested by the Architect, provide a sample of any product or item requested, properly marked and tagged, for the opening for which it is intended. After examination and approval by the Architect, the sample shall be turned over to the General Contractor, for incorporation into the project.

D. Templates:

Upon “Approved” copies of the hardware schedule, provide a complete “Template List”.

Further and upon request, provide copies to manufacturers or trades, whose work in-cludes preparation of their products, to receive hardware. Provide copies of all such transmittals to the contractor, for their files. If physical samples are required, the manu-facturer may request it from the general contractor and assume all responsibility of ship-ping it complete to the project.

E. Operations and Maintenance Data:

At the completion of the project, provide an Owner’s Operation and Maintenance Manual.

The manual shall consist of a hard three ring binder. Include a copy of the latest revised and updated schedule of finish hardware, complete with catalog cuts and keying sched-ule. In addition, furnish one copy of maintenance and parts manual, for those items, for which they are readily available and normally provided.

1.5 QUALITY ASSURANCE

A. Qualifications:

1. Hardware supplier: direct factory contract supplier who employs a certified architectural hardware consultant (AHC), available at reasonable times dur-ing course Work for project hardware consultation to Owner, Architect and Contrac-tor.

DOOR HARDWARE 087100 - 3

(1) Responsible for detailing, scheduling and ordering of finish hardware.

B. Hardware: New, free of defects, blemishes and excessive play. Obtain each kind of hard-ware (latch and locksets, exit devices, hinges and closers) from one manufacturer.

C. Exit Doors: Operable from inside with single motion without the use of a key or special knowledge or effort.

D. Fire-Rated Openings: NFPA 80 compliant. Hardware UL10C / UBC Standard 7-2 (positive pressure) compliant for given type/size opening and degree of label. Provide proper latching hardware, non-flaming door closers, approved-bearing hinges, and resilient seals. Coordi-nate with wood door section for required intumescent seals. Furnish openings complete.

1. Note: scheduled resilient seals may exceed selected door manufacturer’s require-ments.

2. See 2.6.E for added information regarding resilient and intumescent seals.

E. Furnish hardware items required to complete the work in accordance with specified perfor-mance level and design intent, complying with manufacturers’ instructions.

1. Where scheduled item is now obsolete, bid and furnish manufacturer's updated item at no additional cost to the project.

F. Pre-Installation Meetings: Initiate and conduct with supplier, installer and related trades, co-ordinate materials and techniques, and sequence complex hardware items and systems in-stallation. Include manufacturers' representatives of locks, panic hardware and door closers in the meetings. Convene at least one week prior to commencement of related work.

1.6 DELIVERY, STORAGE AND HANDLING

A. Delivery: coordinate delivery to appropriate locations (shop or field).

1. Permanent keys and cores: secured delivery direct to Owner’s representative.

B. Acceptance at Site: Items individually packaged in manufacturers’ original containers, com-plete with proper fasteners and related pieces. Clearly mark packages to indicate contents, locations in hardware schedule and door numbers.

C. Storage: Provide securely locked storage area for hardware, protect from moisture, sunlight, paint, chemicals, dust, excessive heat and cold, etc.

1.7 PROJECT CONDITIONS

A. Where exact types of hardware specified are not adaptable to finished shape or size of members requiring hardware, provide suitable types having as nearly as practical as the same operation and quality as type specified, subject to Architect’s approval.

B. Submittals prepared without thorough jobsite visit by qualified hardware expert will be reject-ed as non-compliant.

1.8 SEQUENCING AND COORDINATION

A. Coordinate with concrete.

B. Reinforce walls for wall-mounted hardware, including wall stops.

DOOR HARDWARE 087100 - 4

C. Coordinate finish floor materials and floor-mounted hardware.

D. Furnish manufacturer templates to door and frame fabricators.

1. Ensure proper reinforcement in metal doors and frames to support machine screws for panic hardware and door closers.

E. Use hardware consultant to check Shop Drawings for doors and entrances to confirm that adequate provisions will be made for proper hardware installation.

1.9 WARRANTY

A. Part of respective manufacturers’ regular terms of sale. Provide manufacturers’ warranties:

1. Locksets: Three years.

2. Exit Devices: Three years mechanical, one year electrical.

3. Closers: Ten years mechanical, two years electrical.

4. Hinges: Life of Building.

5. Other Hardware: Two years.

PART 2 - PRODUCTS

2.1 MANUFACTURERS:

A. General:

1. The following manufacturers have been selected for this project, whose products numbers have been used in the preparation for this specification.

2. Note that even though an acceptable substitute manufacturer may be listed, the product must provide all the functions and features of the specified product or it will not be approved.

3. Hand of Door: Drawings show direction of slide, swing, or hand of each door leaf.

Furnish each item of hardware for proper installation and operation of door move-ment as shown.

4. Schedules

ITEM: MANUFACTURER: ACCEPTABLE SUB:

Butt Hinges (IVE) Ives Stanley, Hager

Continous Hinges (IVE) Ives Select, Roton

Key System (BES) Best Owner’s Standard

Security Lock (KAB) Kaba Owner’s Standard

Locks (BES) Best Owner’s Standard

Exit Devices (VON) Von Duprin Owner’s Standard

Closers (LCN) LCN Sargent 281, Corbin DC8200

Silencers (IVE) Ives Hager, Rockwood

Push & Pull Plates (IVE) Ives Hager, Rockwood

Kickplates (IVE) Ives Hager, Rockwood

Stops (HAG) Hager Approved Equal

Overhead Stops (GLY) Glynn-Johnson Rixson, ABH

DOOR HARDWARE 087100 - 5

Thresholds (NGP) National Guard Reese, Zero

Seals & Bottoms (NGP) National Guard Reese, Zero

2.2 HINGING METHODS

A. Note: drawings typically depict doors at 90 degrees, doors will actually swing to maximum al-lowable. Use wide-throw conventional or continuous hinges as needed up to 8 inches in width to allow door to stand parallel to wall for true 180-degree opening. Advise architect if 8-inch width is insufficient.

B. Conventional Hinges: Steel or stainless steel pins and concealed bearings. Hinge open widths minimum, but of sufficient throw to permit maximum door swing.

1. Three hinges per leaf to 7 foot, 6 inch height. Add one for each additional 30 inches in height, or any fraction thereof.

2. Extra heavy weight hinges on doors over 3 foot, 5 inches in width.

3. Extra-heavy weight hinges on doors with panic hardware or fire exit devices.

4. Out-swinging exterior doors: non-ferrous with non-removable (NRP) pins.

5. Non-ferrous material exteriors and at doors subject to corrosive atmospheric condi-tions.

6. Provide shims and shimming instructions for proper door adjustment.

2.3 LOCKSETS, LATCHSETS, DEADBOLTS

A. Mortise Locksets and Latchsets: as scheduled.

1. Chassis: cold-rolled steel, handing field-changeable without disassembly.

2. Latchbolts: 3/4 inch throw stainless steel anti-friction type.

3. Lever Trim: through-bolted, accessible design, cast lever or solid extruded bar type levers as scheduled. Filled hollow tube design unacceptable.

a. Spindles: security design independent breakaway. Breakage of outside lever does not allow access to inside lever’s hubworks to gain wrongful en-try.

4. Thumbturns: accessible design not requiring pinching or twisting motions to operate.

5. Deadbolts: stainless steel 1-inch throw.

6. Electric operation: Manufacturer-installed continuous duty solenoid.

7. Strikes: 16 gage curved steel, bronze or brass with 1 inch deep box construction, lips of sufficient length to clear trim and protect clothing.

8. Certifications:

a. ANSI A156.13, 1994, Grade 1 Operational, Grade 1 Security.

b. ANSI/ASTM F476-84 Grade 31 UL Listed.

9 Basis of Design: Best 40H Series with 14R Trim

10. Accepted substitutions: No substitutions.

2.4 EXIT DEVICES / PANIC HARDWARE

A. General features:

1. Independent lab-tested 1,000,000 cycles.

2. Push-through push-pad design. No exposed push-pad fasteners, no exposed cavi-ties when operated. Return stroke fluid dampeners and rubber bottoming dampen-ers, plus anti-rattle devices.

DOOR HARDWARE 087100 - 6

3. 0.75-inch throw deadlocking latchbolts.

4. End caps: impact-resistant, flush-mounted. No raised edges or lips to catch carts or other equipment.

5. No exposed screws to show through glass doors.

6. Non-handed basic device design with center case interchangeable with all func-tions, no extra parts required to effect change of function.

7. Releasable in normal operation with 15-lb. maximum operating force per UBC

Standard 10-4, and with 32 lb. maximum pressure under 250-lb. load to the door.

8. Flush end cap design as opposed to typical "bottle-cap" design end cap.

9. Basis of Design: Von Duprin 99 Series

10. Accepted Substitutions: No substitutions

B. Specific features:

1. Non-Fire Rated Devices: cylinder dogging.

2. Lever Trim: Breakaway type, forged brass or bronze escutcheon min .130” thick-ness, match lockset lever design.

3. Removable Mullions: Removable with single turn of building key. Securely rein-stalled without need for key.

2.5 CLOSERS

A. Surface Closers:

1. Full rack-and-pinion type cylinder with removable non-ferrous cover and cast iron body. Double heat-treated pinion shaft, single piece forged piston, chrome-silicon steel spring.

2. ISO 2000 certified. Units stamped with date-of-manufacture code.

3. Independent lab-tested 10,000,000 cycles.

4. Non-sized and adjustable. Place closers inside building, stairs and rooms.

5. Plates, brackets and special templating when needed for interface with particular header, door and wall conditions and neighboring hardware.

6. Separate adjusting valves for closing speed, latching speed and backcheck, fourth valve for delayed action where scheduled.

7. Extra-duty arms (EDA) at exterior doors scheduled with parallel arm units. EDA arms: rigid main and forearm, reinforced elbow.

8. Exterior doors do not require seasonal adjustments in temperatures from 120 de-grees F to –30 degrees F, furnish data on request.

9. Non-flaming fluid, will not fuel door or floor covering fires.

10. Pressure Relief Valves (PRV): unsafe, not permitted.

11. Basis of design: LCN 4040XP Series

12. Accepted substitutions: Sargent 281 series, Corbin-Russwin Dc8200 series, no substitutions.

2.6 OTHER HARDWARE

A. Overhead Stops: Stainless steel. Non-plastic mechanisms and finished metal end caps.

Field-changeable hold-open, friction and stop-only functions.

B. Kick Plates: Four beveled edges, .050 inches minimum thickness, height and width as scheduled. Sheet-metal screws of bronze or stainless steel to match other hardware.

C. Door Stops: Provide stops to protect walls, casework or other hardware.

1. Must be latex free

2. Unless otherwise noted in Hardware Sets, provide wall type with appropriate fas-

DOOR HARDWARE 087100 - 7

teners. Where wall type cannot be used, provide floor type. If neither can be used, provide overhead type.

3. Provide stop at carpeted areas with ½” spacers.

D. Seals: Finished to match adjacent frame color. Resilient seal material: polypropylene, nylon brush, or solid high-grade neoprene. UL label applied to seals on rated doors. Substitute products: certify that the products equal or exceed specified material’s thickness and durabil-ity. Proposed substitutions: submit for approval.

1. Solid neoprene: MIL Spec. R6855-CL III, Grade 40.

2. Non-corroding fasteners at in-swinging exterior doors.

3. Fire-rated Doors, Resilient Seals: UL10C / UBC Standard 7-2 compliant. Coordi-nate with selected door manufacturers' and selected frame manufacturers' require-ments. Where rigid housed resilient seals are scheduled in this section and the se-lected door manufacturer only requires an adhesive-mounted resilient seal, furnish rigid housed seal at minimum, or both the rigid housed seal plus the adhesive ap-plied seal. Adhesive applied seals alone are deemed insufficient for this project where rigid housed seals are scheduled.

E. Thresholds: As scheduled and per details. Substitute products: certify that the products equal or exceed specified material’s thickness. Proposed substitutions: submit for approval.

1. Exteriors: Seal perimeter to exclude water and vermin. Use butyl-rubber or polyisobutylene sealant complying with requirements in Division 7 "Thermal and Moisture Protection". Non-ferrous 1/4inch fasteners and lead expansion shield anchors, or Red-Head #SFS-1420 (or approved equivalent) Flat Head Sleeve Anchors (SS/FHSL).

1. Fire-rated openings, 90min or less duration: use thresholds to interrupt floor covering material under the door where that material has a critical radiant flux value less than 0.22 watts per square centimeter, per NFPA 253. Use threshold unit as scheduled. If none scheduled, request direction from Architect.

3. Fire-rated openings, 3hour duration: Thresholds, where scheduled, to extend full jamb depth.

4. Plastic plugs with wood or sheet metal screws are not an acceptable substitute for specified fastening methods.

E. Fasteners: Generally, exposed screws to be Phillips or Robertson drive. Pinned TORX drive at high security areas. Flat head sleeve anchors (FHSL) may be slotted drive. Sheet metal and wood screws: full-thread. Sleeve nuts: full length to prevent door compression.

H. Silencers: Interior hollow metal frames, 3 for single doors, 4 for pairs of doors. Omit where adhesive mounted seal occurs. Leave no unfilled/uncovered pre-punched silencer holes.

I. Key Control System:

1. Provide a key control system

2. Size for Project plus sufficient room to allow for 10 percent growth.

3. Shall be a 16 GA, grey enamel, wall mounted locking cabinet.

4. Include the following:

a. Collection envelopes

b. Permanent key tags

c. Loan key tags

d. 3-way cross index with binder

e. Permanent loan record with binder

2.7 FINISH

DOOR HARDWARE 087100 - 8

A. Generally BHMA 626 Satin Chromium

1. Areas using BHMA 626 to have push-plates, pulls and protection plates of BHMA 630, Satin Stainless Steel, unless otherwise noted.

B. Door closers: factory powder coated to match other hardware, unless otherwise noted.

C. Aluminum items: match predominant adjacent material. Seals to coordinate with frame col-or.

2.8 KEYING REQUIREMENTS

A. Existing BEST Great Grand Master key system. All cores to be 7 pin small format inter-changeable Cormax core (Verify this with the Owner prior to ordering). No substitutions al-lowed.

B. Contractor is to supply temporary construction cores and keys. Owner will supply/install permanent BEST Cormax cores and do keying at end of project. Owner will turn over con-struction cores/keys to Contractor after permanent cores are in place.

Furnish the following:

4 each construction master keys 2 each construction control keys

PART 3 - EXECUTION

3.1 ACCEPTABLE INSTALLERS

A. Experienced craftsperson with a resume of successful projects.

3.2 PREPARATION

A. Ensure that walls and frames are square and plumb before hardware installation.

B. Locate hardware per SDI-100 and applicable building, fire, life-safety, accessibility, and se-curity codes.

1. Notify Architect of any code conflicts before ordering material.

2. Locate levers, key cylinders, t-turn pieces, touchbars and other operable portions of latching hardware between 30 inches to 44 inches above the finished floor.

3. Where new hardware is to be installed near existing doors/hardware scheduled to remain, match locations of existing hardware.

C. Overhead stops: before installing, determine proposed locations of furniture items, fixtures, and other items to be protected by the overhead stop's action.

3.3 INSTALLATION

A. Install hardware per manufacturer’s instructions and recommendations. Do not install sur-face-mounted items until finishes have been completed on substrate. Set units level, plumb and true to line and location. Adjust and reinforce attachment substrate for proper installa-tion and operation. Remove and reinstall or replace work deemed defective by Architect.

1. Gaskets: install jamb-applied gaskets before closers, overhead stops, rim strikes, DOOR HARDWARE 087100 - 9 etc; fasten hardware over and through these seals. Install sweeps across bottoms of doors before astragals, cope sweeps around bottom pivots, trim astragals to tops of sweeps.

2. When hardware is to be attached to existing metal surface and insufficient rein-forcement exists, use RivNuts, NutSerts or similar anchoring device for screws.

3. Use manufacturers' fasteners furnished with hardware items, or submit Request for Substitution with Architect.

4. Replace fasteners damaged by power-driven tools.

B. Locate floor stops no more that 4 inches from walls and not within paths of travel. See par-agraph 2.2 regarding hinge widths, door should be well clear of point of wall reveal. Point of door contact no closer to the hinge edge than half the door width. Where situation is ques-tionable or difficult, contact Architect for direction.

C. Drill pilot holes for fasteners in wood doors and/or frames.

3.4 ADJUSTING

A. Adjust and check for proper operation and function. Replace units, which cannot be adjust-ed to operate freely and smoothly.

1. Hardware damaged by improper installation or adjustment methods to be repaired or replaced to Owner’s satisfaction.

2. Adjust doors to fully latch with no more than 1 pound of pressure.

B. Inspection: Use hardware supplier. Include supplier's report with closeout documents.

C. Follow-up inspection: Installer to provide letter of agreement to Owner that approximately 6 months after substantial completion, installer will visit Project with representatives of the manufacturers of the locking devices and door closers to accomplish following:

1. Re-adjust hardware.

2. Evaluate maintenance procedures and recommend changes or additions, and in-struct Owner’s personnel.

3. Identify items that have deteriorated or failed.

4. Submit written report identifying problems and likely future problems.

3.5 DEMONSTRATION

A. Demonstrate electrical and electronic hardware systems, including adjustment and maintenance procedures.

3.6 PROTECTION/CLEANING

A. Cover installed hardware, protect from paint, cleaning agents, weathering, carts/barrows, etc. Remove covering materials and clean hardware just prior to substantial completion.

B. Clean adjacent wall, frame and door surfaces soiled from installation/reinstallation process.

3.7 SCHEDULE OF FINISH HARDWARE

A. See door schedule in drawings for hardware set assignments.

B. Manufacturers and their abbreviations used in this schedule:

DOOR HARDWARE 087100 - 10

HW SET: 01

DOOR NUMBER:

101, 102, 103, 104, 105, 106

EACH TO HAVE:

3 EA HINGE 5BB1HW 4.5 X 4.5 652 IVE

1 EA PANIC HARDWARE CD99NL 626 VON

1 EA RIM CYLINDER 1E72 626 BES

1 EA MORTISE CYLINDER 1E74 626 BES

1 EA SURFACE CLOSER 4040XP EDA 18-61 689 LCN

1 EA KICK PLATE 8400 8 H X34 W X B-CS US32D IVE

1 EA THRESHOLD 896S MS/LA AL NGP

2 EA DOOR BOTTOM 39A ZER

1 SET MEETING STILE SEAL 488SCL PSA ZER

1 SET WEATHERSEALS 488SCL PSA ZER

HW SET: 02

DOOR NUMBER:

101A, 102A

EACH TO HAVE:

3 EA HINGE 5BB1HW 4.5 X 4.5 652 IVE

1 EA OFFICE LOCK 45H7A 14R 626 BES

1 EA SURFACE CLOSER 4040XP EDA 18-61 689 LCN

1 EA KICK PLATE 8400 8 H X34 W X B-CS US32D IVE

1 EA THRESHOLD 896S MS/LA AL NGP

2 EA DOOR BOTTOM 39A ZER

1 SET MEETING STILE SEAL 488SCL PSA ZER

1 SET WEATHERSEALS 488SCL PSA ZER

END OF SECTION 087100

KYTC D-11 Bell County Structure Renovation 609-CBY1-Z001-A79 November 11, 2025

Kesler Simpson Architects, LLC 3728 Willow Ridge Road, Lexington, KY 40514 859-523-4324 www.ksa-llc.com

END OF ADDENDUM