Accident Prevention Plan (pdf version).pdf

PDF 3 MB Posted

Attached to
MDOT ACCIDENT PREVENTION PLAN
Solicitation number
RFQ 171 270000000062 1
Issued by
Grand Traverse County, Lansing City, Michigan

About this file

This is an Accident Prevention Plan document that provides guidelines and procedures for workplace safety and injury prevention. The plan outlines comprehensive strategies to identify and mitigate hazards, establish safety protocols, and ensure compliance with occupational safety regulations across operations. The document details responsibilities for safety personnel, emergency response procedures, hazard assessment methodologies, and worker training requirements to minimize workplace accidents and illnesses. It includes protocols for incident reporting, investigation procedures, and corrective action implementation to address identified safety deficiencies and prevent recurrence of accidents.

The plan establishes a framework for ongoing safety monitoring, inspection schedules, and documentation requirements to maintain a safe working environment. It emphasizes the importance of management commitment to safety, employee participation in hazard identification, and continuous improvement of safety practices. The document serves as a foundational reference for all personnel involved in project execution, ensuring consistent application of safety standards and regulatory compliance throughout the contract period.

View the file

Other files

File Type Posted
Standard Contract Terms - Short Form.pdf PDF
State of Michigan Print Mail Management Terms Conditions (1).docx DOCX document
Accident Prevention Plan.docx DOCX document
Accident Plan 2019 cover.pdf PDF
Subcontractor Disclosure form.docx DOCX document

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

March 1, 2019

All MDOT Employees The following document is MDOT’s Accident Prevention Plan (APP). It was developed in order to provide MDOT employees with information that may help prevent workplace injuries and illnesses. The APP is available in a printed pocket-sized version, electronically on MDOT’s intranet at the Safety and Security Administration team website, and as an ePub file for use on mobile devices.

The APP summarizes several existing MDOT safety and health procedures, safety topics, and Michigan Occupational Safety and Health Administration (MIOSHA) regulations. These longer and detailed documents can be viewed individually by accessing MDOT’s intranet.

Please review this document and be familiar with its contents. As required by MIOSHA, a copy of the APP shall be maintained at each worksite.

If you have any questions about this or any other safety issue, please contact the Safety and Security Administration office at 517-241-1697 or MDOT-SafetyAdmin@Michigan.gov.

Paul C. Ajegba, Director

Hazard Communication (Right to Know) –
Labeling Secondary Containers . . . . . . . . . . . . . . . . 29
Hazard Communication – Training. . . . . . . . . . . . . . . . 30
Housekeeping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Lock, Tag, Try (Lockout/Tagout). . . . . . . . . . . . . . . . . . 30
Machine Guarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Night Work and Lighting. . . . . . . . . . . . . . . . . . . . . . . . 33
Overhead Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Respiratory Protection . . . . . . . . . . . . . . . . . . . . . . . . . 34
Slings, Chains, Wire Rope, and Hooks – Chain Slings. 35
Slings, Chains, Wire Rope, and Hooks – Hooks . . . . . 37
Slings, Chains, Wire Rope, and Hooks – Web Slings. . 37
Slings, Chains, Wire Rope, and Hooks – Wire Rope . . 38
Trailer Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Tree Trimming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Underground Utilities – Miss Dig . . . . . . . . . . . . . . . . . 39
Vehicle Operators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Working Over Water. . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Work Zone Safety – Working Next to Traffic . . . . . . . . 40
Work Zone Safety – Traffic Control . . . . . . . . . . . . . . . 41

Section 3 - Health Risks

Asbestos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Bites and Stings – Insects . . . . . . . . . . . . . . . . . . . . . . 42
Bites and Stings – Ticks. . . . . . . . . . . . . . . . . . . . . . . . 43
Bloodborne Pathogens. . . . . . . . . . . . . . . . . . . . . . . . . 45
Dehydration and Fatigue . . . . . . . . . . . . . . . . . . . . . . . 47
Hearing Conservation. . . . . . . . . . . . . . . . . . . . . . . . . . 47
Heat Stress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Lead Exposure in Construction
(Lead Exposure Compliance). . . . . . . . . . . . . . . . . . 50
Lifting Safety (Preventing Back Injuries). . . . . . . . . . . . 51
Methamphetamine Lab Waste. . . . . . . . . . . . . . . . . . . 52
Poisonous Vegetation – Giant Hogweed. . . . . . . . . . . 54
Poisonous Vegetation – Poison Ivy . . . . . . . . . . . . . . . 55
Poisonous Vegetation – Wild Parsnip. . . . . . . . . . . . . . 57
Portland Cement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Silica. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Sun Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

TABLE OF CONTENTS

Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Scope Responsibilities

Section 1 - General Information First Aid

MIOSHA

Personnel Protective Equipment (PPE)

Reporting of Injuries, Illnesses,
and Motor Vehicle Incidents . . . . . . . . . . . . . . . . . . . . 9

Section 2 - Safety

Aerial Lift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Alcohol and Drug-Free Workplace. . . . . . . . . . . . . . . . 10
Avoiding Crime – Personal Safety. . . . . . . . . . . . . . . . 11
Cell Phones, Mobile Devices, and Distractions. . . . . . 11
Compressed Air (Use) . . . . . . . . . . . . . . . . . . . . . . . . . 12
Compressed Gas (Cylinders). . . . . . . . . . . . . . . . . . . . 12
Confined Spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contractor’s Safety Plan. . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Emergency Plans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Equipment – Mobile . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Equipment and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Excavation and Trenching . . . . . . . . . . . . . . . . . . . . . . 17
Fall Protection - Fall Arrest Equipment. . . . . . . . . . . . . 19
Fall Protection – Guardrails . . . . . . . . . . . . . . . . . . . . . 20
Fall Protection – Ladders. . . . . . . . . . . . . . . . . . . . . . . 21
Fall Protection – Scaffolds . . . . . . . . . . . . . . . . . . . . . . 23
Fire Fighting Equipment (Fire Extinguishers). . . . . . . . 26
Gasoline Cans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Hand Protection - Gloves. . . . . . . . . . . . . . . . . . . . . . . 27
Hazard Assessment – Hierarchy of Controls. . . . . . . . 27
Hazard Communication – Safety Data Sheets (SDS). . 28
Hazard Communication (Right to Know) – Labels. . . . 29

4 5

SCOPE

This document covers all MDOT employees engaged in any field activities.

RESPONSIBLITIES

Employer Responsibilities:

MDOT shall develop, maintain, and coordinate with employees an accident prevention program, a copy of which shall be available at the worksite (maintenance site, construction site, etc.).

MDOT’s Safety and Security Administrator is designated as the qualified person with the responsibility to administer the safety program.

Each facility’s management maintains the responsibility to ensure that the safety program, including required training, is provided to the employees.

Employee Responsibilities:

MDOT employees shall immediately report hazardous conditions or equipment to their supervisor.

MDOT employees shall not engage in any act that would endanger another employee or themselves.

If there are any questions about health and safety practices, employees must contact their supervisor.

ACCIDENT PREVENTION PLAN

Michigan Department of Transportation

Developed: March 26, 1992 Revision #02.03: April 5, 2006 Revision #02.04: April 1, 2010 Revision #02.05: May 1, 2013

Revision #02.06: March 1, 2019

PURPOSE

The purpose of this plan is to serve as a guide for basic safety and health requirements for employees of the Michigan Department of Transportation (MDOT) to help aid in the prevention of work-related injury and illness when working in the field.

BACKGROUND

The Michigan Occupational Safety and Health Administration (MIOSHA), Construction Safety Standards, General Rules, Part 1, states that employers shall develop, maintain, and coordinate with employees an Accident Prevention Plan (APP).

6 7

MIOSHA

MIOSHA–Act No. 154 of the Public Acts of 1974, as amended, provides job safety and health protection for Michigan employees through the maintenance of safe and healthful working conditions. MIOSHA covers both public (state) and private employees. MIOSHA can inspect MDOT facilities and worksites/ projects. MIOSHA’s primary means of enforcement of safety and health standards is by issuance of citations.

If a MIOSHA inspector visits your worksite, contact your supervisor and MDOT Safety and Security Administration.

Personal Protective Equipment (PPE) The MDOT guidance document Personal Protective Equipment (PPE) Policy, #10118, describes the department’s PPE policy, including specific information and requirements, including references to current standards for eye, head, foot protection, and high-visibility apparel. Employees are to be familiar with and in compliance with the policy. Failure to comply may result in disciplinary action.

Section 1-

GENERAL INFORMATION

First Aid MDOT follows first aid certification requirements for employees based on the rules set forth by MIOSHA. MIOSHA Part 1, General Rules, Rule 132, requires: “(3) A person who has a valid certificate in first aid training shall be present at the worksite to render first aid.” All MDOT field employees are required to have a valid certificate in first aid and must also possess a valid certificate in cardiopulmonary resuscitation (CPR).

First aid supplies shall be available at each worksite and readily accessible. First aid kits can be secured from the MDOT Central Warehouse. Contents should be checked periodically for replacement of expired or depleted supplies.

8 9

Reporting of Injuries, Illnesses, and Motor Vehicle Incidents An employee who suffers a work-related injury or illness is to immediately report the injury to their supervisor. After care has been provided and the work area made safe, the supervisor is to investigate. To provide a record of the injury and/or illness, the employee and supervisor are to report applicable information on MDOT Form 0003, Injury and Illness Incident Report. The MDOT guidance document Injury and Illness Incident Reporting, #10147, provides guidelines for reporting occupational injuries and illnesses.

Employees are to immediately report all motor vehicle incidents and equipment damage, regardless of cost, to their supervisor. The supervisor is to investigate the crash/incident.

To provide a record of the incident/damage, and prior to any repairs, the employee and supervisor are to report applicable information on MDOT Form 0007, Motor Vehicle Incident Report. The MDOT guidance document Motor Vehicle Incident Reporting, #10211, provides guidelines for reporting motor vehicle incidents.

Eye, head, and foot protection must be worn outdoors while engaging in, inspecting, or observing any work activities. An American National Standards Institute (ANSI) 107 Class 2 or 3 safety vest shall be worn when performing, inspecting, or observing work within the right of way of the road.

Depending on the type of work activity, it may be necessary to wear other and/or additional PPE including, but not limited to: hearing protection, hand protection, respirators, and protective clothing, such as chain saw chaps/leggings, etc. Workers and supervisors should assess the task before leaving the facility to ensure the right PPE is available and should re-assess once at the worksite to ensure compliance.

10 11

Avoiding Crime - Personal Safety Stay alert and aware of your surroundings at all times. Think of the situation (night versus day, certain areas, etc.) and whether the task should be done differently than normal to ensure your safety. Limit personal valuables, such as cash and credit cards. Think about where you are driving and parking. Let co-workers know your destination and estimated time of arrival and/or return.

Cell Phones, Mobile Devices, and Distractions Distractions while driving or while working in a work zone can lead to serious incidents.

Workers must be able to devote their full attention to the task at hand. While in a work zone, distractions may prevent workers from hearing directions from co-workers, noticing equipment, or hearing back up alarms.

Per Federal Motor Carrier Safety Administration (FMCSA), commercial motor vehicle (CMV) drivers are prohibited from texting, reaching or holding a mobile phone, or pressing multiple buttons to dial.

Additionally, MDOT employees are required to follow MDOT guidance document Wireless Devices in State Vehicles, #10216.

Section 2 - SAFETY Aerial Lift Use of a body harness and lanyard are required when using an aerial lift, such as a bucket truck. Only approved anchor points shall be used for attaching lanyards. Capacity of the bucket shall not be exceeded. Pre-operational inspections are required before each day’s use. Emergency ground level controls shall be clearly marked as to their intended function and be capable of overriding the platform controls and shall be accessible whenever an aerial lift is used. Rescue or self-rescue of employees using aerial lifts must be considered at all times and locations.

(Refer to Fall Protection–Fall Arrest Equipment and Equipment–Mobile in Section 2.)

Alcohol and Drug-Free Workplace Employees shall not work while under the influence of intoxicating beverages or substances that would impair his or her ability to perform a task in a safe manner. (Refer to MDOT guidance document titled Alcohol and Drug-Free Workplace Policy, #10077.)

MDOT shall not knowingly permit an employee to work while that employee is under the influence of intoxicating beverages or substances that could impair the employee’s ability to perform a task in a safe manner.

12 13

Confined Spaces Confined spaces are defined by the following three characteristics:

• It has adequate size and configuration for employee entry. (Can you get in?)

• It has limited means of entry or exit. (Can you get trapped, no matter how unlikely?)

• It is not designed for continuous employee occupancy. (Are there potential hazards, no matter how remote?)

Examples of confined spaces include (but not limited to):

•Tunnels and sewers
•Manholes
•Segmental bridges
•Pump houses and stations
•Culverts and cofferdams
•Catch basins
•Boilers
•Vaults

Potential hazards in a confined space include (but not limited to):

•Atmospheric conditions
•Flammable atmospheres
•Burn hazards
•Electrical hazards
•Drowning
•Mechanical hazards
•Asphyxiation

Compressed Air (Use) All compressed air link couplers must be pinned to prevent accidental disconnection.

Compressed air used for blowing out joints and cracks must be performed using wands 48 inches or longer in length from valve to tip. Wands shall have a chip guard to protect the operator. Compressed air used for dust removal on tools and equipment must be regulated to less than 30 pounds per square inch (psi) or shall have a diffuser at the end.

Compressed Gas (Cylinders) Chains, brackets, or other devices shall be used at all times to restrain compressed gas cylinders from falling, sliding, and rolling while in storage or transport.

•Toxic conditions
•Heat stress hazards
•Engulfment hazards
•Noise hazards
•Physical hazards

(slip, trip, etc.)

•Well and sump pits
•Surge chambers
•Vaults
•Silos
•Fan housings
•Mechanical rooms
•Storage tanks
•Vents and ducts

14 15

Electrical In the field, electrical tools must be used with a ground fault circuit interrupter (GFCI) grounded power supply.

Extension cords must not have frayed insulation or be fastened with staples, hung from nails, or suspended from wires.

All extension cords must have grounded plugs (three prongs) intact.

All temporary lights must be equipped with non-conductive guards.

Electrical systems shall not be worked on “live” and must be locked out per MDOT guidance document Lock, Tag, Try (Lockout/Tagout) Procedure, #10203.

Arc flash precautions must be taken when working with live circuits if lock, tag, try cannot be done.

Emergency Plans Unlike a building that must have an emergency plan for fire, severe weather, and other emergencies, a field job site and work zone may be different every day. Workers should assess their situation and think about what they should do in case of an emergency, such as severe weather. Depending on the situation, this may mean finding a nearby shelter, sheltering in the vehicle, or driving out of the path (perpendicular to) of a tornado, etc. Each situation is different, but preparing ahead of time can make a difference.

Be sure to follow the appropriate procedures for dealing with a confined space. (Refer to MDOT Confined Space Entry Procedure.)

Always discuss the potential hazards before entering a confined space to ensure all hazards are eliminated.

Contractor’s Safety Plan Contractors are required by MIOSHA to have their own accident prevention plan.

This plan should include emergency contact information. Safety Data Sheets (SDS) (formerly known as Material Safety Data Sheets) for materials used by the contractor are to be shared with MDOT employees, if requested. MDOT employees may be exposed to safety and health hazards when on a contractor job site. Do not assume that the contractor is correctly dealing with a hazard.

16 17

The operation of machinery, equipment, and special tools, except by anyone other than a qualified employee, is not allowed. Equipment should not be modified unless approved by the manufacturer, as well as MDOT Safety and Security Administration and/or MDOT Office of Operations Administrative Services, Fleet Administration and Operations.

Excavation and Trenching The basic components to safely perform an excavation or trench are described below.

For additional information, refer to MIOSHA Construction Safety Standards, Part 9, Excavation, Trenching, and Shoring.

• Material removed shall be stored and retained at least 2 feet from the excavation edge.

Equipment - Mobile An employee, other than the operator, shall not ride any piece of moving equipment, unless there is a seat or other safety feature provided for use by that employee. Acceptable safety features could include a guardrail, enclosure, or a seat belt.

All equipment left unattended at night, adjacent to a highway in normal use or adjacent to construction areas where work is in progress, shall have appropriate lights or reflectors, or barricades equipped with appropriate lights or reflectors, to identify the location of the equipment (unless parked outside the clear zone).

Operators of mobile equipment (aerial lifts, excavators, front end loaders, etc.) must have a valid certification to operate the equipment.

Equipment and Tools Use hand tools only for their designed/ intended purpose.

Machines, hand tools, powered tools, or any other piece of equipment shall be inspected before use. If damaged or defective, they shall not be used. The damaged or defective machine, tool, or equipment shall be locked or tagged out, made inoperable, or be physically removed from the worksite.

Contact your supervisor to repair or replace unsafe equipment.

The use of damaged or defective machinery, tools, materials, or equipment that could create a hazard is prohibited.

18 19

• A sidewalk shall not be undermined unless it is shored to support a live load of not less than 125 pounds per square foot.

• A walkway or sidewalk that is adjacent to an excavation shall be protected by a guardrail.

(Refer to Fall Protection - Guardrails in Section 2.)

• An employee shall not work in an excavation in which there is accumulated water or in which water is accumulating unless precautions have been taken to protect employees against the hazards posed by water accumulation.

• An ongoing inspection of an excavation or trench shall be made by a qualified person.

• After every rainstorm or other hazard-producing occurrence, an inspection shall be made by a qualified employee for evidence of possible slides or cave-ins. Where these conditions are found, all work shall cease until additional precautions, such as additional shoring or reducing the slope (angle of repose), have been accomplished.

Fall Protection - Fall Arrest Equipment Each employee working at a level 6 feet (1.8 m) or more above a lower level should be protected from falling by either a guardrail system, safety net system, or personal fall arrest system (this does not apply to those working on a ladder). The use of a personal fall arrest system should be considered the last level of protection if no other fall prevention methods can be offered.

• An excavation 48 inches or more (deep) shall provide a ladder extending not less than 3 feet above the top.

• Distance between ladders, or other means of egress, within a trench shall not exceed 25 feet.

• The side of an excavation more than 5 feet deep shall be sloped (angle of repose) depending on the soil. For example, dry granular soil or dry sand and clay may require a minimum slope of 1 to 1 (or a 45-degree angle). (Refer to MIOSHA Part 9, Excavation, Trenching, and Shoring, Table 1 for detail on angle of repose.)

• When a shoring system is used, the system shall be designed and used to resist the added pressure when heavy equipment, material handling equipment, or material is located near an excavation.

• A support system (shoring system) shall be designed by a qualified person and the design shall be maintained at the worksite.

MIOSHA defines a qualified person as: a person who, by possession of a recognized degree or certificate of professional standing, or by extensive knowledge, training, and experience, has successfully demonstrated the ability to solve or resolve problems relating to the subject matter and work.

• Portable trench boxes, or sliding trench shields, may be used if they are designed, constructed, and maintained in a manner that provides worker protection.

20 21 the top rail and the walking surface, but no less than 21 inches high.

• Top rails shall be able to withstand a 200-pound force applied in any outward or downward direction.

• Mid-rails shall be able to withstand a 150-pound force applied in any outward or downward direction.

• To protect employees or the motoring public from falling objects, such as hand tools, debris, and other small objects, toe boards may be installed.

Fall Protection - Ladders

• Choose a ladder tall and strong enough for the job. Make sure the ladder fits the job.

• Position the ladder for steadiness.

•Be sure the ground surface is level and stable.
•Place safety feet parallel to the floor or ground.
•Use the 4 to 1 rule for straight ladders (meaning

for every 4 feet of rise, have 1-foot setback). If a ladder is used at a pitch of 5 to 1, the ladder shall be secured at the top to prevent it from tipping backwards.

• Extend the ladder at least 3 feet above the top surface.

•Secure the ladder (at bottom or top) as needed.
•Check the ladder to ensure all parts are in

good condition.

• Rungs or steps should be in good condition and free from mud, oil, grease, or other slippery substances.

Personal fall arrest systems, when stopping a fall, shall:

• Limit maximum arresting force on an employee to 1,800 pounds when used with a body harness.

• Be rigged such that an employee can neither free fall more than 6 feet, nor contact any lower level.

• Bring an employee to a complete stop and limit maximum deceleration distance an employee travels to 3.5 feet.

• Have sufficient strength to withstand twice the potential impact energy of an employee free-falling a distance of 6 feet, or the free fall distance permitted by the systems, whichever is less.

A safety harness, lanyard, or lifeline, including the hardware, shall be inspected before use each day. Body harnesses and lanyards must be of the appropriate size for the employee.

Anchor points, body wear (harnesses), and connectors (lanyards) must be appropriate for the task as no one system fits all. Rescue plans, where workers are using fall arrest equipment, must be considered before going to the job site.

Fall Protection - Guardrails Guardrails shall meet the following specifications:

• Top rail shall be 42 inches, plus or minus

3 inches, from the walking surface.

• Mid-rails shall be installed midway between

22 23

• Never set ladders on boxes or other objects to make the ladder reach higher areas.

• Lock or barricade any doors that may open towards a ladder.

• Never use stepladders as straight ladders.

Open stepladders fully and make sure that the spreader(s) is (are) locked securely.

• Ladders should not be painted because paint may conceal defects.

• When not in use, ladders should be kept on racks having sufficient supporting points to prevent sagging. If a ladder is stored vertically, it should be secured to prevent falling.

Fall Protection - Scaffolds A scaffold and its components must be capable of supporting, without failure, not less than four times the maximum intended load.

Scaffolds and scaffold components must be inspected for visible defects by a competent person before each work shift. MIOSHA defines a competent person as: a person who is experienced and capable of identifying an existing or potential hazard in surroundings, or under working conditions that are hazardous or dangerous to an employee and who has the authority and knowledge to take prompt corrective measures to eliminate the hazards.

Scaffold poles, legs, posts, frames, and uprights must rest on base plates and mud sills or other adequate firm foundation.

• Side rails should be in good condition (straight, no splits).

• All hardware, including braces, bolts, screws, and spreaders should be in place.

• Rope, used for extension, should be in good condition.

•Safety feet should be in place and in good condition.
•Tag out and do not use any damaged or

defective ladder.

• Work cautiously on a ladder to prevent falls.

•Only allow one person on a ladder.
•Wear boots with clean, nonskid soles.
•Face the ladder and hold both rails while climbing,

if possible.

•Carry tools on a belt or rope or hoist up.
•Stay below the top two stepladder steps or top

3 feet of an extension ladder.

• Work with your body centered between the rails.

Use the “belt buckle” rule (meaning, do not let your belt buckle go outside the rails).

•Maintain three points of contact on ladders.
•Do not use a metal ladder around

electricity (unless you can maintain 20 feet clearance). Non-conductive ladders can use the following clearances below:

Voltage Minimum Clearance Up to 50,000 volts 10 feet

Over 50,000 volts

10 feet plus 0.4 inch per thousand volts

24 25

Workers must not be allowed within 10 feet of uninsulated electrical energized lines.

If a scaffold is erected within 10 feet of an electrical line, the utility or property owner must be consulted. An electrical line or electrical apparatus is to be considered energized unless the property owner or utility advised that it is de-energized and the line or apparatus is visibly grounded. Otherwise, the minimum clearances set forth in the tables below shall be maintained between the scaffold, employee, or material, whichever is closer.

INSULATED LINES

Voltage Minimum Distance Less than 300 volts 3 feet (0.9 meters) 300 to 50,000 volts 10 feet (3.1 meters)

More than 50,000 volts

10 feet (3.1 meters) plus 0.4 inches (1 centimeter) for each thousand volts over 50,000 volts

UN-INSULATED LINES

Voltage Minimum Distance Less than 50,000 volts 10 feet (3.1 meters)

More than 50,000 volts

10 feet (3.1 meters) plus 0.4 inches (1 centimeter) for each thousand volts over 50,000 volts

A guardrail must be installed on any open side or end of a scaffold work platform that is 10 (3.1 meters) or more feet above the floor or ground.

If wood planks are used for a work platform, then the planks must be scaffold-grade lumber of no less than 2 x 10 inches. The platform must consist of a minimum of two planks laid side by side. Each platform on all working levels of scaffolds must be fully planked or decked between uprights where practicable.

Planking must extend over the end bearer not less than 6 inches, but not more than 12 inches and be cleated or otherwise fastened to prevent shifting and be of uniform thickness, except where lapped. Hook-on-type manufactured work platforms may be used if they are secured to the bearer.

To protect employees from falling objects, such as hand tools, debris, and other small objects, toe boards may be installed or the use of screens, guardrail systems, debris nets, catch platforms, or canopy structures can be used to contain or deflect falling objects.

26 27

Gasoline Cans Type I or Type II safety cans must be used for gasoline. As a reminder, all fuel cans, including gasoline, must be secured during transport to prevent sliding, rolling, or tipping.

Hand Protection - Gloves Many hand injuries can be prevented by wearing the proper hand protection. Choose the right type of glove for the job you are performing. Make sure they are in good condition and fit properly. Wear them.

Hazard Assessment - Hierarchy of Controls Supervisors and employees should routinely review their facilities and/or worksites to determine if safety or health hazards exist and to take action in one or more of the following means:

•Safely remove or eliminate the hazard.
•Substitute or replace the hazard.
•Isolate or guard against the hazard by

implementing engineering controls.

• Implement administrative controls to change how the work is done including training of workers.

• Provide personal protective equipment, as the last line of defense, and enforce its use.

Fire Fighting Equipment (Fire Extinguishers) To reduce the chance of fire and injury to employees, fire fighting equipment (fire extinguishers) shall be provided in all MDOT commercial motor vehicles and located where they can be readily seen and accessible. Only use an extinguisher when it is safe to do so.

Remember the word “PASS” for use.

P–Pull the pin. A–Aim at the base of the fire.

S–Squeeze the handle. S–Sweep the base of the fire. For vehicle fires, do not open the hood, but instead discharge the extinguisher in a partially opened gap. Care should be taken to use an extinguisher upwind and near a corner of the vehicle versus the front or sides.

Fire extinguishers shall be inspected monthly, or at more frequent intervals when circumstances require. Inspections shall check for all of the following:

• The extinguisher is in its designated place

(and secure).

• The extinguisher has not been actuated or tampered with.

• The extinguisher does not have obvious damage, physical damage, external corrosion, or other impairment.

• The gauge on the fire extinguisher, if equipped, reads in the acceptable range.

Fire extinguishers shall receive a thorough inspection at least once a year to ensure operability.

28 29

Hazard Communication (Right to Know) - Labels All containers of hazardous chemicals (meaning any chemical that has a physical or health hazard) must be labeled. Labels are not to be removed or defaced. Labels must have at least the following:

•Product identifier.
•Signal word (“Danger” or “Warning” or none

at all, if applicable).

•Pictograms.
•Hazard and precautionary statements.
•Name, address, and telephone number in

case of an emergency.

Hazard Communication (Right to Know) - Labeling Secondary Containers Secondary containers, into which hazardous chemicals are transferred from labeled containers, must be labeled if the material is not used “immediately” (by that person on that shift). Secondary container labels using the original chemical’s GHS format may be available from the chemical distributor.

Alternatively, a roll of “peel and stick” labels can be purchased in either the National Fire Protection Association (NFPA) or Hazardous Material Identification System (HMIS) format.

Information to complete the labels can typically be found on the original container label or the chemical’s SDS.

Hazard Communication - Safety Data Sheets (SDS) (Formerly Material Safety Data Sheets) An SDS must be available, at the workplace or worksite, for each and all hazardous chemicals. With the Globally Harmonized System (GHS), the SDS format is now standardized so that all chemicals have essential information in the same sections.

Workers should pay particular attention to the Hazard Identification section (section 2) for the signal word (“Danger” or “Warning”), pictograms, and hazard statements. SDS must be readily accessible to employees. If employees must travel between worksites (meaning, their work is carried out at more than one location), the safety data sheets may be kept at the primary location, but the employee must be able to immediately obtain the required SDS information in an emergency. For MDOT crews that do not return to their official work station facility during their work shift, meaning they leave the facility at the start of the work week and do not return until the end of the work week, they need to have copies of SDSs with them for the chemicals they have on hand. MDOT locations must identify the location of and the person responsible for maintaining the SDS.

30 31 is controlled by unplugging the equipment from the energy source, the unplugged cord must be under the exclusive control of the employee conducting the service or maintenance activities. If exclusive control can not be assured, then other means of control must be considered, such as plug covers and locks.

A basic shutdown procedure for lock, tag, try:

1. Before shutdown. The authorized employee must know the type and magnitude of the energy, the hazards of the energy to be controlled, and the method or means to control the energy. There may be multiple energy sources on one piece of equipment.

2. Shutdown. The authorized employee shuts down the machine or equipment by the normal stopping procedure, such as pressing the stop button, moving the switch to the “off” position, etc.

3. Isolation. The main power switches, circuits, or additional sources of energy are moved to the “off” position or otherwise made inoperative. Unplugging the equipment is a simple means of isolation.

4. Lock (Lockout). Locks are placed on switches or other energy sources in the “safe” or “off” position. Warning tags shall be placed with each lock.

5. Energy release. All potentially hazardous stored or residual energy (such as that in springs, elevated parts, rotating flywheels, hydraulic systems, electrical systems, air, Hazard Communication - Training Each employee who may be “exposed” to hazardous chemicals, when working, must be provided information and trained, prior to initial assignment, on how to work with a hazardous chemical.

Housekeeping Materials, including scrap and debris, shall be piled, stacked, or placed so as not to create a hazard to employees. This applies to facilities, field job sites, and equipment. Good housekeeping allows for safe access and egress and helps prevent potential slip and trip hazards.

Lock, Tag, Try (Lockout/Tagout) Before servicing or maintenance is performed on machinery or equipment, the machinery or equipment must be turned off and disconnected from the energy source, and the energy–isolating device must be locked and tagged out.

Employees are required to perform lock, tag, try whenever the power source of any machine to be repaired, serviced, or set up, that could (if activated) create an unexpected motion, or surge of power that could cause injury. (Refer to MDOT guidance document Lock, Tag, Try (Lockout/Tagout) Procedure, #10203.)

For cord and plug-connected electrical equipment, for which exposure to the hazards of unexpected start up of the equipment

32 33

No machine should be started without guards in place. If guards are missing or defective, report it to the supervisor immediately. For abrasive wheel grinders, the top (tongue) guard must not have a gap larger than 1/4 inch and the tool rest guard must not have a gap larger than 1/8 inch.

Night Work and Lighting When working in low light conditions, be sure you and your vehicle, as well as your traffic control devices, are visible. A Class 3 safety vest is recommended for working at night (required for MDOT maintenance crews).

Lighting for working at night shall be a minimum of 5 footcandles in areas where work is not being immediately performed but where workers may pass through. A minimum of 10 footcandles shall be provided where work is being performed. Lights should be directed so as not to cause glare for the both the motorists and the workers. Headlamps worn by the workers can help meet the lighting requirements.

gas, steam, or water pressure, etc.) is relieved, disconnected, or otherwise made safe by repositioning, blocking, bleeding down, etc.

6. Try (Testing). After making sure that no personnel are exposed, and as a check on having disconnected the energy sources, the authorized employee operates the push button or other normal operating controls to make certain the equipment will not operate. Caution: Return operating controls to the “neutral” or “off” position after the test.

Machine Guarding Hazards from any means of power transmission, including, but not limited to, belts, gears, shafts, pulleys, sprockets, spindles, drums, flywheels, chains, or other reciprocating, rotating, or moving parts of equipment, shall be guarded if the part is exposed to possible contact by an employee or otherwise constitutes a hazard.

MDOT employees shall not remove a guard or other safety device from a machine or equipment, except for authorized servicing purposes. The guard or other safety device shall be replaced, or equivalent guarding shall be provided before the machine or equipment is returned to normal operation. Employees shall not reach around, under, over, or through a guard into hazardous areas.

34 35

Respirators used must be certified by the National Institute for Occupational Safety and Health (NIOSH) and must be labeled as such. Cartridges and equipment cannot be interchanged between manufacturers.

Respirators that use cartridges and filters must have the appropriate filter for the hazard/ exposure.

Workers who are required to wear respirators must have a medical evaluation before being assigned a respirator.

All workers must be fit tested annually if they wear a tight-fitting respirator (negative or positive pressure). Fit testing must also be done prior to initial use of any respirator or when there are changes in the employee’s physical condition that could affect respirator fit (e.g., obvious change in body weight, facial scarring, dental changes, cosmetic surgery, etc.).

Workers must be fit tested with the make, model and size of respirator they will wear. All workers shall conduct user seal checks each time they wear their respirator.

Slings, Chains, Wire Rope, and Hooks

- Chain Slings Whenever any chain sling is used, the following practices shall be observed:

• Chain slings that are damaged or defective shall not be used.

• Chain slings shall not be loaded in excess of their rated capacities.

Overhead Utilities Employees shall not be allowed to work or be closer to energized electrical line, gear, or equipment exposed to contact than the minimum clearance prescribed below:

Voltage Minimum Clearance Up to 50,000 volts 10 feet

Over 50,000 volts

10 feet plus 0.4 inch per thousand volts

If adequate clearances cannot be maintained, an insulated barrier shall be installed on the exposed energized part or the energized part shall be de-energized and grounded.

Respiratory Protection Respirators are worn in situations where airborne hazards cannot be reduced to a safe level by ventilation or other engineering controls.

When wearing a respirator, make sure it’s designed to protect against the specific type and level of airborne hazard present.

For example, exposure to silica dust, lead, chemicals, and asbestos all have different respirator and filter requirements.

It is important to make sure the airborne hazards have been identified, including the concentration, and then determine the best respirator to use for that given hazard and exposure level.

36 37

Slings, Chains, Wire Rope, and Hooks - Hooks Hooks with deformations, cracks, or bent open too far (MIOSHA regulations say more than 15 percent in excess of normal throat opening) or bent off center (MIOSHA regulations say more than 10 degrees of twist from the plane of an unbent hook) shall be discarded. Repairs are not recommended. If such repairs are attempted, they shall only be done under competent supervision and the hook shall be tested to the load requirements.

Hooks with “keepers” must be in good condition and replaced if damaged or missing.

Slings, Chains, Wire Rope, and Hooks - Web Slings Synthetic web slings shall be marked or coded to show: name or trademark of manufacturer, rated capacities for the type of hitch, and type of material.

A synthetic web sling shall be immediately removed from service if any of the following conditions are present:

•Acid or caustic burns.
•Melting or charring of any part of the sling

surface.

•Snags, punctures, tears, or cuts.
•Broken or worn stitches.
•Distortion of fittings.

• Chain slings shall be securely attached to their loads.

• Suspended loads shall be kept clear of all obstructions.

• All employees shall be kept clear of loads about to be lifted and of suspended loads.

• Hands or fingers shall not be placed between the sling and its load while the sling is being tightened around the load.

• Shock loading is prohibited (do not jerk the load suddenly).

Chain slings used for lifting loads must be tagged to show the size, grade, rated capacity, and manufacturer’s name.

Before use, chain slings and all fastenings and attachments shall be inspected for damage. Damaged or defective slings shall be immediately removed from service.

38 39

Tree Trimming Chaps shall be worn when operating chain saws unless working from an aerial lift.

Hearing protection and the proper eye protection shall be worn (such as a face shield) in addition to the normal PPE. When operating a chipper, knit wrist gloves shall be worn to prevent being snagged by branches.

Be sure to assess the site before cutting and to look for overhead power lines. (Refer to Personal Protection Equipment in Section 1.)

Underground Utilities - Miss Dig Before performing any excavating, trenching, or boring, it is important to call Miss Dig at least three full working days prior to the start of the project. Miss Dig can be reached at 800-482-7171 or 811, 24 hours a day/seven days a week. The Miss Dig association member utilities will mark the approximate location of their underground public utility facilities with flags, paint, or both.

MDOT is excluded and not required to be a part of the Miss Dig system. MDOT may have its own electrical or other infrastructure within the right of way. For MDOT crews digging, boring or performing other operations within the right of way, it is recommended to check the location of MDOT’s own utilities by referring to the “as built” plans available on ProjectWise or by contacting the appropriate region staff who may have knowledge about any infrastructures in the area.

Slings, Chains, Wire Rope, and Hooks - Wire Rope Wire rope (cable) should be treated like any other piece of equipment with regard to inspection and maintenance. It needs to be lubricated. The wires within the cable need to slide on each other as they coil and flex.

Rusted strands can lead to premature failure and cause breaks. Wire rope also needs to be coiled in a tight even manner so as not to crush underlying coils that can lead to “flat spots” on the wire rope causing premature failure.

Wire rope should be removed from service if there are broken wires, evidence of heat damage, wear, kinks, crushes, or corrosion.

Trailer Towing Safety chains shall be connected every time a trailer is being towed. Chains should be crossed under the coupler to prevent the tongue of the trailer from dragging or digging into the road should it come off the hitch. Do not let safety chains drag on the road. Each safety chain should have a breaking strength equal to or greater than the gross trailer weight rating. Always connect the break-away cable to the towing vehicle separately from the safety chains. If the truck or trailer hitch is equipped with a hole for a safety pin, it must be used.

40 41

Vehicle Operators No employee shall operate an MDOT vehicle without a valid operator’s license or, when necessary, a commercial driver’s license (CDL). The CDL requires a valid medical card.

Before operating an MDOT vehicle, employees shall make sure, to the best of their ability, that the vehicle is in proper operating condition, including conducting of pre- and post-trip inspections. Any unsafe condition shall be reported to the supervisor.

Seatbelts shall be worn by drivers and passengers. This is advisable even if the vehicle is parked along the side the road.

Working Over Water When working over water, such as on bridges, there must always be some form of fall protection system in place. This could include a guardrail system or the use of body harnesses with lanyards and/or lifelines. If there is a chance a worker could fall into the water, then some means of rescue must be available. This could include the use of ring buoys with at least 90 feet of rope, a boat, or immediate rescue services. Likewise, if there is a chance of falling into the water, then life vests that are U.S. Coast Guard-approved are necessary.

Work Zone Safety - Working Next to Traffic MDOT workers should think safety at all times, especially when working near traffic.

Suggestions include: do not turn your back to traffic or work with a traffic spotter, when possible; assume all lanes are open to traffic; never assume traffic sees you; do not walk side by side; pay attention to work equipment and operators; know where you are at all times; always have an escape path;

never assume the driver is driving safely;

and always look and listen. Try not to get complacent or used to working near traffic.

Work Zone Safety - Traffic Control The function of traffic control is to maintain a safe, reasonable flow of traffic through a temporary traffic control zone while at the same time protecting the workers. MDOT employees should ensure traffic control is appropriate for the hazards encountered and follow recommendations as provided in the Michigan Manual on Uniform Traffic Control Devices (MMUTCD) and other support documents. Work zones should be monitored to ensure the motoring public is behaving as desired and adjusted to ensure the safety and separation of both the motorists and the workers.

When deploying traffic control devices, it is best to go with the flow of traffic. When retrieving traffic control devices, it is best to go opposite the flow of traffic. Proper equipment with guardrails and handholds must be in good condition for safe deployment and retrieval. Intrusion into a live lane of traffic should be limited or not at all depending on the traffic volume and conditions.

42 43

Section 3 -

HEALTH RISKS

Asbestos Asbestos can be found in gaskets, pipe covering, floor tile, ceiling tile, conduits, and in certain concrete or sealants. If the asbestos fibers are bonded together, it is safe. If the surface is crumbled, blistered, water stained, gorged, marred, or otherwise abraded, or if there is an accumulation of powder, dust, or debris similar in appearance to the suspect material on surfaces beneath the suspect material, then proper precautions must be taken, including respiratory protection and protective clothing.

Bites and Stings - Insects The insects most commonly associated with triggering severe allergic reactions (anaphylaxis) are:

•Bees•Hornets
•Wasps•Ants
•Yellow jackets

A normal response to an insect sting is swelling, pain, and redness around the site of the sting or bite. When a person is allergic to an insect sting, serious symptoms will appear within 20 minutes, which can include:

•Itching and hives over much of the body.
•Swelling in the throat or tongue.
•Difficulty breathing or swallowing.
•Dizziness, severe headache.
•Stomach cramps, nausea, or diarrhea.
•Rapid fall in blood pressure.
•Shock and loss of consciousness.

It is important to remember that these symptoms can progress quickly, so treatment should be administered immediately. This may include the use of epinephrine on site and transportation to a medical facility for additional treatment.

Bites and Stings - Ticks A tick has a one-piece body. The harpoon-like barbs of its mouth attach to a host for feeding.

Crablike legs and a sticky secretion help hold the tick to the host.

There are several different diseases that can be transmitted by ticks. The most common one in Michigan is Lyme disease. It is a bacterial infection transmitted from one animal to another, or to humans, through the bite of an infected tick. The body does not maintain a natural immunity to the disease, and a person can be reinfected with the disease on subsequent tick bites.

Signs and symptoms of early local Lyme disease often start with flu-like feelings of headache, stiff neck, fever, muscle aches, and fatigue. About 60 percent of light-skinned patients notice a unique enlarging rash (often seen as a “bull’s eye”) days to weeks after the bite. On dark-skinned people, this rash

44 45 resembles a bruise. The rash may appear within a day of the bite or as late as a month later. This rash may start as a small, reddish bump about one-half inch in diameter. It may be slightly raised or flat. It soon expands outward, often leaving a clearing (normal flesh color) in the center. It can enlarge to the size of a thumb-print or cover a person’s back.

To reduce your chance of getting a tick bite:

• Avoid tick-infested areas, when possible.

Use caution when you are entering tick-infected areas. Stay in the center of paths and avoid sitting on the ground.

• Wear light-colored clothing. This allows you to more easily see ticks on your clothing and gives you the opportunity to remove them before they can attach to your skin and feed. Wear a long-sleeved shirt and long pants. This reduces the skin area exposed to ticks. Also, tuck your shirt into your pants and pants into your socks.

This keeps the ticks on the outside of your clothing and may prevent their efforts to crawl onto your skin. However, during warm or hot weather, this is not practical.

• Use Environmental Protection Agency-approved tick repellents. Be sure to read the instructions for use as some are to be applied to clothing only prior to being worn.

As they are not insects, ticks typically do not respond to insect repellants.

• Conduct frequent tick checks. This includes a visual inspection of the clothing and exposed skin. Be sure to check the scalp, behind and in the ears, groin area, and behind any joints.

Bloodborne Pathogens Bloodborne pathogens are micro-organisms present in human blood and bodily fluids referred to as other potentially infectious material (OPIM).

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .