The file's text, extracted by GovTribe without its formatting.
Sheet1 Open Market RUBBER TRACKED FORESTRY COMPACT LOADER Verify Specification (yes,no) Vendor Notes
| BASIC SPECIFICATIONS |
| Engine net flywheel power shall be at least 130hp. |
| The machine shall have a SAE rated operating capacity of 4000-4500 lbs at 35% |
| The height to the top of the cab shall be no more than 91 in. |
| Machine shall have a minimum ground clearance of no less that 8 in. |
| ENGINE |
| All equipment must meet or exceed U.S. EPA engine emission standards in effect for manufacturing as of the date of purchase contract. No waivers or credits may be applied. |
| Engine shall be direct fuel injected, turbocharged, liquid cooled. |
| Engine shall be equipped with a cold weather starting aid to include a 120 volt electric engine coolant heater. |
| Air filtration shall be accomplished via a radial seal air cleaner with a secondary backup. The air intake system shall include a pre-cleaner, as well as a convenient in-cab air flow restriction indicator. |
| The engine and hydraulic oil coolers shall have an ambient temperature cooling capacity of 100° F. |
| The cooling fan and radiator shall allow easy access to the engine. |
| Unit shall have a enclosed fan that can run reverse direction on either automatic or operator mode and fan drive guarding |
| The cooling fan shall be driven so that it maintains constant airflow and fan speed, even under a load that would cause the engine to lug. |
| The engine compartment shall have a debris barrier and be lockable. |
| The machine shall have braided, color-coded and numbered wiring harness for easy diagnostics. |
| The machine shall have sealed pin connectors to prevent dirt and moisture infiltration. |
| The machine shall have a main system relay to prevent fires. |
| POWERTRAIN/TRANSMISSION |
| Two hydrostatic drive pumps shall be splined directly to the engine via a flexible coupling for maximum efficiency, reliability and serviceability. |
| Shall have 2 speed control. |
| Hand and foot throttles shall be provided to allow the operator to match engine speed to a task. The hand throttle shall allow the operator to maintain consistent engine speed and the foot throttle shall allow the operator to vary engine speed and minimize fuel consumption. |
| Maximum forward travel speed shall be at least 7 mph with two speed option. |
| STEERING |
| The machine shall be equipped with a hydraulically operated joystick that controls the forward/reverse and steering directions. |
| BRAKES |
| Machine shall have a spring applied, hydraulically released parking brake that shall automatically engage when arm bar is raised, and shall be designed to hold machine static at any point on a 2 to 1 slope. |
| HYDRAULIC SYSTEMS |
| The machine shall be equipped with a hydraulically operated joystick that controls the lift, lower and tilt functions. |
| The high - flow pump flow of the machine shall be at least 50 gal/min. |
| The hydraulic pressure of the machine shall be at least 3,100 psi. |
| Machine shall be equipped with auxiliary hydraulics activated by a thumb switch located on joystick. |
| The machine shall be equipped with a hydraulic tank that has an anti-cavitation loop. |
| The machine shall be equipped with hydraulic pressure hoses that shall have steel spiral wraps with burst protection of at least 4,000 psi. |
| Standard auxiliary hydraulics to power tools shall be available through quick connect hydraulic couplings that are rigidly mounted to the loader arm. |
| The machine shall be equipped with a high-flow to standard-flow switch located in the cab. |
| AXLES |
| Machine shall have heavy-duty torsion axles to suspend each side of the undercarriage from the machine frame and axles shall be shock absorbing |
| UNDERCARRIAGE |
| Rubber track shall be lightweight, pliable and reinforced. |
| Machine ground pressure shall not exceed 4.7 psi. |
| Undercarriage shall consist of an open design that allows easy cleaning of components. |
| ELECTRICAL |
| The machine shall be equipped with a battery that has at least 12 volts and 650 CCA for cold start capabilities in 32° F (0°C) climate. |
| The machine shall have a back up alarm. |
| The machine shall have two LED rear working lights, two LED rear tail lights, two LED adjustable front lights, dome light, and a LED low profile strobe warning beacon. |
| OPERATORS STATION |
| The machine shall be equipped with deep skid-resistant, self-cleaning steps. |
| The machine shall have no foot controls used to operate loader arm, tilt function or auxiliary hydraulics. |
| The machine shall be equipped with both a hand and a foot throttle. |
| The machine shall have a retractable seat belt. |
| The machine shall have a adjustable suspension air-ride cloth seat. |
| The machine shall come standard with an arm bar that when lifted, automatically engages the machine parking brake for added operator comfort and safety. |
| The machine shall be equipped with ROPS protective structure meeting SAE J1040 standards. |
| Machine shall come with impact resistant heavy duty door to be used in Forestry applications. |
| Shall have 3" seatbelt |
| Machine shall come with standard enclosed cab door |
| The machine shall be equipped with a Level II FOPS protective structure meeting SAEJ/ISO 3449 standards. |
| The machine shall have an enclosed cab with air conditioning, heater, and defroster system. |
| The machine shall have a horn, headliner, fuel gauge, and a hour meter. |
| Heater shall be equipped with an integrated shutoff valve for summer operation. |
| The machine shall have audible warning alarms for engine coolant temperature, engine oil pressure and hydraulic oil temperature. |
| The cab door shall be equipped with a lockout mechanism that prevents loader arm movement with door in open position and constructed/designed for use in demolition or forestry applications with a wiper and washer. |
| The machine shall be equipped with a rear view camera placed in location on the machine where susceptibility of damage is minimal. The display screen located in the cab and placed in a location that will not effect operator view in the cab. |
| The side safety glass shall be sliding and the rear safety glass shall have emergency exit capability. |
| Machine shall be equipped with a standard 12V electrical socket. |
| Shall provide and install a AM/FM/Weather band radio with Bluetooth capability. |
| LOADER LINKAGE/STRUCTURES |
| The pins shall have countersunk grease fittings to protect them from damage. |
| The machine shall be equipped with two tilt cylinders, protected by a heavy-duty torque tube. |
| The machine shall have a tipping capacity of at least 10,000 lb. |
| The machine shall have a dump angle of at least 50° for superior bucket cleanout. |
| The machine shall have an arched transition to the coupler for increased dump clearance. |
| The machine shall have a rated operating capacity of at least 4000-4500 lbs at 35% without adding additional counterweights. |
| The machine shall have a self-leveling hydraulic system. |
| The vertical lift linkage shall provide a consistent and uniform lift path for maximum reach throughout the entire lift cycle. |
| Maximum hinge pin height at maximum lift shall be at least 120 in. |
| Reach at maximum lift and dump shall be at least 30 in. |
| Clearance at maximum lift and dump shall be at least 90 in. |
| Roll back angle at ground level shall be at least 30 degrees. |
| Maximum reach with arms parallel to the ground shall be 50 in. |
| Tilt cylinder breakout force shall be at least 60000 lb. |
| Lift cylinder breakout force with high flow shall be at least 5500 lb. |
| REQUIRED WORK TOOL OPTIONS |
| Machine shall have a universal quick coupler. |
| Coupler shall have hydraulic engagement and disengagement of work tools from inside the cab. |
| Machine shall have a work tool electrical switch. |
| The machine shall have a standard bucket with bolt on cutting edges. Bucket minimum width no less than the overall width of the machine. |
| SERVICEABILITY |
| Maintenance points shall be grouped in easily accessible locations. |
| The machine shall be equipped with grouped, spin-on, fuel/water separator, engine oil and hydraulic oil filters. |
| The radiator, hydraulic oil cooler and grill shall be protected by a guard, and still maintain access to the engine. |
| The machine shall be equipped with sight gauges on the hydraulic tank and the radiator. |
| The machine shall be equipped with standard system pressure and fluid analysis test ports. |
| The machine shall have an electronic port allowing electronic machine diagnostics. |
| The machine shall have a cab that tilts which exposes all pumps, motors, valves and lines by an individual using a single tool. |
| The machine shall have a cab that is held in place by a self-latching mechanism. |
| The machine shall not have any required maintenance points that require lifting of the cab structure. |
| Machine shall have a solid steel door, with a bumper that slightly protrudes beyond the door, in order to prevent damage to engine compartment components. |
| The rear door shall open 90 degrees for easy access to both sides of the mounted engine. |
| A removable belly pan section in the floor of the lower frame shall provide access for periodic cleaning. |
| The machine shall have environmental style fluid drains with fluid sampling ports. |
| All filters shall be easily accessible, which makes routine service quicker and virtually spill free. |
| MINIMUM SERVICE FILL CAPACITIES |
| Cooling system shall have at least a 4 gal capacity. |
| Fuel tank shall have a least a 25 gal capacity. |
| Hydraulic system shall have at least a 11 gal capacity. |
| Hydraulic tank shall have at least a 8 gal capacity. |
| Engine crankcase shall have at least a 2 gal capacity. |
| OWNING AND OPERATING COSTS |
| Extended life coolant shall be standard. |
| The machine shall have a one (1) year full coverage warranty with an additional three (3) year extended powertrain warranty. A copy of all warranty information will be provided to the delivery station. |
| Minimum of four hours of machine orientation shall be provided for each receiving location. It shall include operational, service and safe operating techniques. |
| The OEM will provide two (2) paper copies of the Owners/Operating Manuals and one (1) digital copy of the Parts Manual. |
| Machine shall come with a remote monitoring and assist management system. It shall include a minimum basic 5 year subscription of service. |
| SAFETY |
| The machine shall have four (4) tie down points. |
| The machine shall have a slow moving emblem with a removable mounting system. |
| The machine shall have a 2 1/2 lb. ABC fire extinguisher mounted for emergency access. |
| Rear guarding and screening to protect engine compartment from falling or striking objects from top and sides. Guarding shall not inhibit access to engine compartment. |
| OPTIONS (Priced individually) These options will be available for purchase at time of ordering and will not be part of the base machine bid. |
| Mulching Head Two speed, 71" cutting width, rated for machine HP and Flow |
Sheet2
Sheet3