PROPOSAL REPORT

Project: 97621 Bid Package: 1

Current Let: 12/10/2026 11:00:00 AM Version: Current

Addendum Count: 0

District: 03 County: Bradford

SR/SEC/Group ID: 187/076/BRIDGE REHAB CONTR

Description SR 187 ov Tr Wysox Cr

PROPOSAL Report - Project 97621

Page 1 of 104October 21, 2026 13:49:45 PM

TABLE OF CONTENTS

BID PACKAGE SUMMARY 5

PROJECT ITEMS AND QUANTITIES 6

SPECIAL PROVISIONS 14

G51A - a00051 APPLICABLE DESIGNATED SPECIAL PROVISIONS (STATE) 14 G113B - a00113 CONTRACT PROVISIONS - RIGHT-TO-KNOW LAW 14 C171A - a00171 CHANGES TO SPECIFICATIONS: SECTIONS 313, 314, 360, 410, 412, and 413 15 C172A - a00172 CHANGES TO SPECIFICATIONS: SECTIONS 107, 871, 872, 875, and 876 22 C173B - a00173 CHANGES TO SPECIFICATIONS: SECTION 106 27 G810A - a00810 MIXTURE ACCEPTANCE AND DENSITY ACCEPTANCE 31 G1401A - a01401 EQUAL EMPLOYMENT OPPORTUNITY WITH PREQUALIFICATION 32 G2302A - a02302 Worker Protection and Investment 33 G3401A - a03401 PREVAILING WAGE ACT 34 G3501B - a03501 RECIPROCAL LIMITATIONS ACT REQUIREMENTS FOR CONSTRUCTION 35 G4251A - a04251 UTILITIES-USE WHEN THERE ARE UTILITIES W/IN THE PROJECT LIMITS

THAT ARE NOT AFFECTEDMPMS98975 36

D29890C - a29890 SPECIAL BIDDING – DESIGN-BUILD 36 D29899A - a29899 QUALITY PLAN WITH QUALITY ASSURANCE REVIEW BY DEPARTMENT -

LOW BID DESIGN 45

S6012B - b06012 - SECTION 601.3(f) BACKFILLING TRENCH 48 S6092B - b06092-SECTION 609.2(f) MISCELLANEOUS MATERIALS 49 G30005B - r300005 RECLAIMED ASPHALT PAVEMENT (RAP) INDUSTRY-WIDE COPRODUCT

DETERMINATION 50

G30020E - r300020 EMERGENCY RESPONSE PROVISIONS 50 G30240D - r300280 ADVANCE NOTICE OF TRAFFIC RESTRICTIONS 51 G30330B - r300330 PERMANENT SIGNS 52 G30335C - r300335 POSITIVE DRAINAGE SURVEY 52 G30340C - r300340 NOTICE TO BIDDERS - RIGHT-OF-WAY RESEARCH 52 G30434D - r300434 CONSTRUCTION RESTRICTIONS 54 S30043C - s0304131 SECTION 413.3(g)3 Paving Notches 55 S30045D - s0304132 SECTION 413.3(k) Joints. 1. Longitudinal Joints. 1.a General 55 S30035F - s0304133 SECTION 413.3(k) Joints. 3.Other Joints 56 S30048A - s0304136 Section 413.3(j)4. Pavement Cores 57 S30055C - s0304910 SECTION 491 MILLING OF BITUMINOUS PAVEMENT SURFACE 57 S30070D - s0306010 SECTION 601 PIPE CULVERTS 57 S30073C - s0306011 SECTION 601.3(c) LAYING PIPE 58 S30093E - s0306270 SECTION 627 TEMPORARY BARRIER 58 S30094E - s0306280 SECTION 628 RESET TEMPORARY BARRIER 59 S30096E - s0306300 SECTION 630 PLAIN CEMENT CONCRETE CURB 59 S30098D - s0306760 SECTION 676 CEMENT CONCRETE SIDEWALKS 60 S30931A - s0309311 SECTION 931 POST MOUNTED SIGNS, TYPE B 60 S30935A - s0309351 SECTION 935 POST MOUNTED SIGNS, TYPE F 61

Page 2 of 104October 21, 2026 13:49:45 PM

S30117E - s0309620 SECTION 962 WATERBORNE PAVEMENT MARKINGS 61 S30963A - s0309630 SECTION 963 PAVEMENT MARKING REMOVAL 62 S30971A - s0309711 SECTION 971 REMOVE POST MOUNTED SIGNS, TYPE B 62 S30975A - s0309751 SECTION 975 REMOVE POST MOUNTED SIGNS, TYPE F 63 S30128E - s0310011 SECTION 1001 CEMENT CONCRETE STRUCTURES 63 S30170G - s0311090 SECTION 1109 GUIDE RAIL AND METAL MEDIAN BARRIER 64 I30010C - t0302010 ITEM 0201-0001 - CLEARING AND GRUBBING 64 I30040E - t0302050 ITEM 0205-0364/0368 - SELECTED BORROW EXCAVATION ROCK, CLASS R-4 65 I30050G - t0302051 ITEM 4205-0368- SELECTED BORROW EXCAVATION ROCK CLASS R-8

(GROUTED) 66

I6091L - t03060909 ITEM 0609-0009 EQUIPMENT PACKAGE 66 00 - t03062004 ITEM 4620-0400 - TERMINAL SECTION, SINGLE (THRIE-BEAM CONNECTION) 68 00 - t03067702 ITEM 4677-0002 - SELECTED MATERIAL SURFACING (SUBBASE NO. 2A) 68 I30310D - t0309010 ITEM 0901-0001 - MAINTENANCE AND PROTECTION OF TRAFFIC DURING

CONSTRUCTION 69

I30310D - t0309010 ITEM 0901-0002 - MAINTENANCE AND PROTECTION OF TRAFFIC DURING

CONSTRUCTION 71

I30468A - t030958 ITEM 4958-0142 - TEMPORARY TRAFFIC CONTROL SIGNALS, TRAILER

MOUNTED PORTABLE DEVICE ETC. 72

00 - t03101804 ITEM 1018-0048 – REMOVAL OF PORTION OF EXISTING BRIDGE 72 00 - t03101812 ITEM 1018-0125 – REMOVAL OF EXISTING BRIDGE SUPERSTRUCTURE 73 I30595A - t0310190 ITEM 5019-0040 - PROTECTIVE COATING FOR REINFORCED CONCRETE

SURFACES (SUBSTRUCTURE) ETC 74

I30596A - t0310191 ITEM 5019-0050 - PROTECTIVE COATING FOR REINFORCED

CONCRETESURFACES(SUPERSTRUCTURE) ETC. 75

00 - t0390001 ITEM 9000-0001 - PRE-CONSTRUCTION AND POST-CONSTRUCTION

INSPECTIONS 76

00 - t0390003 ITEM 9000-0003/0007 - TYPE 31 NESTED THRIE-BEAM GUIDE RAIL (5-FT

RADIUS), ETC. 78

00 - t0390008 ITEM 9000-0008 - CAP INLET 79 I30830F - t0390010 ITEM 9000-0010 - PAVED DRIVES 79 00 - t0390012 ITEM 9000-0012 - TEMPORARY PEDESTRIAN BARRICADE 80 00 - t0390013 ITEM 9000-0013 - OVEREXCAVATION AND BACKFILL WITH NO. 57 COARSE

AGGREGATE 81

00 - t0390015 ITEM 9000-0015 - 6” P.V.C. PIPE (SCHEDULE 40) 82 I30865F - t0390016 ITEM 9000-0016 - PAVED DRIVE AND SIDE ROAD OVERLAYS 82 00 - t0390051 ITEM 9000-0051 - TEMPORARY POLE AND GUY SUPPORT 83 00 - t0390101 ITEM 9000-0101 TEMPORARY PUMP BYPASS SYSTEM 85 I33021A - t0390399 ITEM 9000-0399 STOCKPILING AND PLACING NATIVE STREAMBED

MATERIAL 85

I35680G - t0390680 Item 9000-0680 ELASTOMER WATERPROOFING MEMBRANE ON BRIDGE

DECKS 86

P680A - t0390681 ITEM 9000-0681 SPRAY APPLIED LIQUID WATERPROOFING MEMBRANE

SYSTEM ON OTHER SURFACES 89

Page 3 of 104October 21, 2026 13:49:45 PM

00 - t0391037 ITEM 9000-1037 - FLOWABLE FILL 93 D32200C - t0393000 ITEM 9000-3000 - DESIGN ADA CONCRETE CURB RAMP 93 I68C - t0395101 ITEM 9000-5101 ELECTRONIC TICKETING (E-TICKETING) FOR

CONSTRUCTION AGGREGATE 97

I70C - t0395103 ITEM 9000-5103 ELECTRONIC TICKETING (E-TICKETING) FOR

CONSTRUCTION CONCRETE 98

D1B - t0396012 ITEM 9000-6012 – CONSTRUCT CONCRETE CURB RAMPS AND SIDEWALKS

(BY QUADRANT) 99

I2032A - t3920321 ITEM 9203-0101 TEMPORARY EXCAVATION SUPPORT AND PROTECTION

SYSTEM 101

Page 4 of 104October 21, 2026 13:49:45 PM

BID PACKAGE SUMMARY

Project: 97621 Bid Package: 1

Project Type: Standard Posted:

Federal Project Status: Non - Federal (100% State) State Type of Work: BRIDGE REPLACEMENT

Prequalification Required: Yes Pre-Bid Meeting: None

408 Version: 2026-1

Scheduled Let: 12/10/2026 11:00:00 AM Project Cost Range: $1,000,000.00 - $2,499,999.99 Anticipated NTP: 01/25/2027 Structure Work: 36.00%

Required Completion: 11/18/2027 Wage Rates: Yes

Description:

The description and location of the project are as follows: bridge rehabilitation, including superstructure replacement of the retaining wall, tree trimming, guiderail, line painting, full depth reconstruction/mill & overlay, drainage, DB ADA curb ramps, temporary traffic signals, and other miscellaneous construction, as indicated on the approved drawings included in the bid package for STATE ROUTE 187, SECTION 076/071, in BRADFORD COUNTY ROME BOROUGH from approximately 0.5 miles NORTH of intersection SR 1022 (N Rome Rd) at segment 0640 offset 110 to approximately 2.5 miles SOUTH of intersection SR 1036 (Orwell Hill Rd) at segment 0710 offset 0026.

Additional Information:

This is an ECMS project. All Addenda will be electronically posted.The location of the public bid opening is the Commonwealth Keystone Building, 7th Floor, Contract Awards Room, 400 North Street, Harrisburg. Allow sufficient time before the bid opening to contact Contract Awards and be escorted to the 7th Floor Contract Awards Room. Contract Awards can be reached at 717-395-9754.

Due to recent changes in the Keystone Building, there is no longer a reception on the 5th Floor to greet and check-in visitors.

Page 5 of 104October 21, 2026 13:49:45 PM

PROJECT ITEMS AND QUANTITIES

Alt Item Work Class Code Unit Of

Measure Quantity Unit Price PDP Spec

Prov Add Action

0201-0001 A Lump Sum 1.0000 N Std

CLEARING AND GRUBBING

0203-0001 C Cubic Yard 476.0000 N

CLASS 1 EXCAVATION

0203-0006 G4 Linear Foot 392.0000 N

SAW CUTTING

0204-0100 C1, S1, T1 Cubic Yard 449.0000 N

CLASS 3 EXCAVATION

0205-0297 C1, S4 Cubic Yard 69.0000 N

STRUCTURE BACKFILL, COARSE AGGREGATE NO. 57

0205-0364 C1 Ton 10.0000 N Std

SELECTED BORROW EXCAVATION ROCK, CLASS R-4

0205-0368 C1 Ton 66.0000 N Std

SELECTED BORROW EXCAVATION ROCK, CLASS R-8

4205-0368 C1 Ton 66.0000 N Std

SELECTED BORROW EXCAVATION ROCK, CLASS R-8 (GROUTED)

0205-0385 C1 Ton 3.0000 N

SELECTED BORROW EXCAVATION, COARSE AGGREGATE, NO. 57

0212-0001 C3, H, M2 Linear Foot 289.0000 N

GEOTEXTILE, CLASS 1

0212-0014 C3, H, M2 Square Yard 1,085.0000 N

GEOTEXTILE, CLASS 4, TYPE A

0313-0537 E Ton 233.0000 N SUPERPAVE ASPHALT MIXTURE DESIGN, BASE COURSE, PG 64S-22, 3 TO < 10 MILLION ESALs, 25.0 MM MIX

0316-0537 E, F1 Ton 541.0000 N

SUPERPAVE ASPHALT MIXTURE DESIGN, FLEXIBLE BASE REPLACEMENT, PG 64S-22, 3 TO < 10 MILLION ESALs, 25.0

MM MIX

0350-0121 C, E Ton 297.0000 N

SUBBASE (NO. 2A)

0413-0309 F Ton 1,214.0000 N SUPERPAVE ASPHALT MIXTURE DESIGN, WEARING COURSE, PG 64S-22, 3 TO < 10 MILLION ESALS, 9.5 MM MIX, SRL-G

0413-1029 F Ton 572.0000 N

SUPERPAVE ASPHALT MIXTURE DESIGN, WEARING COURSE (SCRATCH), PG 64S-22, 3 TO < 10 MILLION ESALS, 9.5 MM

MIX, SRL-L

0413-6057 F Ton 97.0000 N

Page 6 of 104October 21, 2026 13:49:45 PM

SUPERPAVE ASPHALT MIXTURE DESIGN, BINDER COURSE, PG 64S-22, 3 TO < 10 MILLION ESALS, 19.0 MM MIX

0413-9999 X Dollar 6,993.0000 $1.00 Y

PERCENT WITHIN LIMITS (PWL) LOT INCENTIVE/DISINCENTIVE

0460-0004 F4 Gallon 2,913.0000 N

ASPHALT TACK COAT (NTT/CNTT)

0461-0002 F4 Gallon 54.0000 N

ASPHALT PRIME COAT

0491-0014 F3 Square Yard 76.0000 N MILLING OF ASPHALT PAVEMENT SURFACE, 2 1/2" DEPTH, MILLED MATERIAL RETAINED BY CONTRACTOR

0491-0021 F3 Square Yard 12,471.0000 N MILLING OF ASPHALT PAVEMENT SURFACE, 2 1/4" DEPTH, MILLED MATERIAL RETAINED BY CONTRACTOR

0601-0353 H Linear Foot 4.0000 N

18" THERMOPLASTIC PIPE, GROUP III, 8'-2' FILL

0601-7014 H Linear Foot 36.0000 N

18" REINFORCED CONCRETE PIPE, TYPE A, 15' - 2' FILL, 100 YEAR DESIGN LIFE

0604-7014 H Linear Foot 44.0000 N 18" REINFORCED CONCRETE PIPE, TYPE A, (OPEN JOINT), 15' - 2' FILL, 100 YEAR DESIGN LIFE

0605-2771 K Set 1.0000 N

TYPE C FRAME AND BICYCLE SAFE GRATE

0605-2781 K Set 1.0000 N

TYPE M FRAME AND BICYCLE SAFE GRATE

0605-2850 K Each 2.0000 N

STANDARD INLET BOX, HEIGHT < /= 10'

0608-0001 X Lump Sum 1.0000 N

MOBILIZATION

0609-0004 X Lump Sum 1.0000 N

INSPECTOR'S FIELD OFFICE AND INSPECTION FACILITIES, TYPE C

0609-0009 X Lump Sum 1.0000 N Std

EQUIPMENT PACKAGE

0610-7002 H2 Linear Foot 289.0000 N

6" PAVEMENT BASE DRAIN

0610-7400 H2 Cubic Yard 15.0000 N

ADDITIONAL COARSE AGGREGATE FOR EXTRA DEPTH PAVEMENT BASE DRAIN

0615-0022 H2 Linear Foot 27.0000 N

6" SUBSURFACE DRAIN OUTLETS

0615-0040 H2 Each 2.0000 N

SUBSURFACE DRAIN OUTLET ENDWALL

Page 7 of 104October 21, 2026 13:49:45 PM

0615-0066 C1, H2, R Each 2.0000 N

66" RED SUBSURFACE DRAIN OUTLET MARKER

0619-0458 J3 Each 1.0000 N

PERMANENT IMPACT ATTENUATING DEVICE, TYPE II, TEST LEVEL 2, TANGENT (MASH)

0620-0400 J Each 1.0000 N

TERMINAL SECTION, SINGLE

4620-0400 J Each 2.0000 N Proj

TERMINAL SECTION, SINGLE (THRIE-BEAM CONNECTION)

0620-1600 J Linear Foot 13.0000 N

TYPE 31-S GUIDE RAIL

0620-2010 J Each 2.0000 N

THRIE-BEAM GUIDE RAIL TO CONCRETE BRIDGE BARRIER TRANSITION WITHOUT CURB

0620-2041 J Each 2.0000 N

THRIE-BEAM TERMINAL CONNECTOR

0627-3019 J1 Linear Foot 282.0000 N

TEMPORARY BARRIER, TEST LEVEL 3, BARRIER DEFLECTION DISTANCE < /=1'

0628-3019 J1 Linear Foot 243.0000 N

RESET TEMPORARY BARRIER, TEST LEVEL 3, BARRIER DEFLECTION DISTANCE < /=1'

0630-0025 K Linear Foot 173.0000 N

PLAIN CEMENT CONCRETE CURB, 4" HEIGHT, INCLUDING REMOVAL OF EXISTING CURB

0676-0001 K Square Yard 96.0000 N

CEMENT CONCRETE SIDEWALK

0676-0004 K Square Yard 10.0000 N

DRIVEWAY APRONS AND SIDEWALKS THROUGH DRIVEWAYS

4677-0002 C1, E Ton 63.0000 N Proj

SELECTED MATERIAL SURFACING (SUBBASE NO. 2A)

0680-0121 K2, S1 Square Yard 14.0000 N

MEMBRANE WATERPROOFING SYSTEM INSTALLED ON OTHER SURFACES

0686-0040 X Lump Sum 1.0000 N

CONSTRUCTION SURVEYING, TYPE C

0686-0050 X Lump Sum 1.0000 N

CONSTRUCTION SURVEYING, TYPE D

0689-0003 X Lump Sum 1.0000 N

CPM SCHEDULE

0690-0001 X Dollar 1,000.0000 $1.00 Y

INTERNAL FACILITATION

0696-0610 J1 Each 2.0000 N

TEMPORARY IMPACT ATTENUATING DEVICE, TYPE V (STANDARD), TEST LEVEL 3

Page 8 of 104October 21, 2026 13:49:45 PM

0697-0610 J1 Each 2.0000 N

RESET TEMPORARY IMPACT ATTENUATING DEVICE, TYPE V (STANDARD), TEST LEVEL 3

0703-0025 C1, H Cubic Yard 18.0000 N

NO. 57 COARSE AGGREGATE

0802-0001 C1, M Cubic Yard 48.0000 N

TOPSOIL FURNISHED AND PLACED

0804-0025 M3 Pound 20.0000 N

SEEDING AND SOIL SUPPLEMENTS - FORMULA B RESIDENTIAL MIX, INCLUDING MULCH

0804-0030 M3 Pound 1.0000 N SEEDING AND SOIL SUPPLEMENTS - FORMULA R SEASONALLY FLOODED CONSERVATION MIX, INCLUDING MULCH

0804-0032 M3 Pound 5.0000 N

SEEDING - FORMULA T TEMPORARY GRASS MIX, INCLUDING MULCH

0804-0051 ZZ Acre 1.0000 N

MOWING

0804-0060 X Dollar 750.0000 $1.00 Y

SOIL TESTING

0806-0113 M2 Square Yard 425.0000 N

TEMPORARY SHORT-TERM, ROLLED EROSION CONTROL PRODUCT, TYPE 2D

0810-0025 M1 Each 7.0000 N

SELECTIVE TREE TRIMMING

0845-0001 M2 Dollar 5,000.0000 $1.00 Y

UNFORESEEN WATER POLLUTION CONTROL

0855-0003 M2 Each 1.0000 N

PUMPED WATER FILTER BAG

0855-0004 M2 Each 1.0000 N

REPLACEMENT PUMPED WATER FILTER BAG

0856-0001 C1 Each 1.0000 N

REMOVAL SEDIMENT AND ROCK BARRIER

0860-0000 M2 Each 2.0000 N

INLET FILTER BAG FOR TYPE M INLET

0860-0002 M2 Each 1.0000 N

INLET FILTER BAG FOR TYPE C INLET

0867-0012 M2 Linear Foot 582.0000 N

COMPOST FILTER SOCK, 12" DIAMETER

0901-0001 Q Lump Sum 1.0000 N Std

MAINTENANCE AND PROTECTION OF TRAFFIC DURING CONSTRUCTION

0901-0002 Q Lump Sum 1.0000 N Std

Page 9 of 104October 21, 2026 13:49:45 PM

MAINTENANCE AND PROTECTION OF TRAFFIC DURING CONSTRUCTION

0901-0320 O Linear Foot 21,324.0000 N

4" STANDARD PAVEMENT MARKINGS, PAINT & BEADS, YELLOW

0901-0330 O Linear Foot 23,801.0000 N

4" STANDARD PAVEMENT MARKINGS, PAINT & BEADS, WHITE

0901-0331 O Linear Foot 614.0000 N

6" STANDARD PAVEMENT MARKINGS, PAINT & BEADS, WHITE

0901-0334 O Linear Foot 50.0000 N

24" STANDARD PAVEMENT MARKINGS, PAINT & BEADS, WHITE

0901-0461 Q Each 4.0000 N

FULL-MATRIX CHANGEABLE MESSAGE SIGN WITHOUT TELECOMMUNICATIONS

0931-0001 R Square Foot 75.0000 N

POST MOUNTED SIGNS, TYPE B

0935-0001 R Square Foot 15.0000 N

POST MOUNTED SIGNS, TYPE F

0937-0105 J, R Each 2.0000 N

GUIDE RAIL MOUNTED DELINEATOR TYPE B, (Y/Y)

0937-0114 J, R Each 2.0000 N

GUIDE RAIL MOUNTED DELINEATOR TYPE D, (W/W)

0937-0339 R Each 2.0000 N FLEXIBLE DELINEATOR POST, GROUND-MOUNT TYPE GM-2, RED POST WITH WHITE/BLANK SHEETING

0941-0001 R Each 2.0000 N

RESET POST MOUNTED SIGNS, TYPE B

0945-0001 R Each 2.0000 N

RESET POST MOUNTED SIGNS, TYPE F

0958-0061 P, Q Each 2.0000 N

TEMPORARY TRAFFIC CONTROL SIGNAL, PEDESTAL-MOUNTED PORTABLE DEVICE

4958-0142 P, Q Each 4.0000 N Std

TEMPORARY TRAFFIC CONTROL SIGNALS, TRAILER-MOUNTED PORTABLE DEVICE (2-OVERHEAD SIGNALS WITH

LUMINAIRES) (ONE ADDITIONAL POST-MOUNTED SIGNAL)

0958-0461 P, Q Each 4.0000 N

RESIDENTIAL DRIVEWAY TEMPORARY SIGNAL

0962-1000 O Linear Foot 10,030.0000 N

4" WHITE WATERBORNE PAVEMENT MARKINGS

0962-1001 O Linear Foot 136.0000 N

6" WHITE WATERBORNE PAVEMENT MARKINGS

0962-1005 O Linear Foot 9,908.0000 N

4" YELLOW WATERBORNE PAVEMENT MARKINGS

Page 10 of 104October 21, 2026 13:49:45 PM

0963-0001 O2, O3 Square Foot 50.0000 N

PAVEMENT MARKING REMOVAL

0963-0004 O2, O3 Linear Foot 1,054.0000 N

4" PAVEMENT MARKING REMOVAL

0963-0006 O2, O3 Linear Foot 71.0000 N

6" PAVEMENT MARKING REMOVAL

0971-0001 R Each 1.0000 N

REMOVE POST MOUNTED SIGNS, TYPE B

0975-0001 R Each 2.0000 N

REMOVE POST MOUNTED SIGNS, TYPE F

1001-0611 T7 Linear Foot 88.0000 N

6" STRUCTURE FOUNDATION DRAIN

1001-1000 S9 Cubic Yard 20.0000 N

CLASS AAAP CEMENT CONCRETE

1001-1080 S2 Cubic Yard 5.0000 N

CLASS AA CEMENT CONCRETE

1001-1120 S2 Cubic Yard 198.0000 N

CLASS A CEMENT CONCRETE

1002-0052 S7 Pound 21,889.0000 N

REINFORCEMENT BARS, EPOXY COATED

1002-0140 S7 Each 28.0000 N

MECHANICAL SPLICE SYSTEM FOR NO. 5 REINFORCEMENT BARS, EPOXY COATED

1002-0220 S7 Pound 328.0000 N

STAINLESS STEEL REINFORCEMENT BARS

1003-0006 S2 Each 168.0000 N

DOWEL HOLES, 14" DEPTH

1003-0008 S2 Each 29.0000 N

DOWEL HOLES, 18" DEPTH

1016-0005 J2, S4 Linear Foot 96.0000 N

BARRIER PROTECTIVE FENCE, STEEL

1018-0048 T1 Lump Sum 1.0000 N Proj

REMOVAL OF PORTION OF EXISTING BRIDGE

1018-0125 T1 Lump Sum 1.0000 N Proj

REMOVAL OF EXISTING BRIDGE SUPERSTRUCTURE

5019-0040 K2 Square Yard 306.0000 N Std

PROTECTIVE COATING FOR REINFORCED CONCRETE SURFACES (PENETRATING SEALERS, REINFORCED

CONCRETE SUBSTRUCTURE SURFACES) (100% SILANE)

Page 11 of 104October 21, 2026 13:49:45 PM

5019-0050 K2 Square Yard 35.0000 N Std

PROTECTIVE COATING FOR REINFORCED CONCRETE SURFACES (PENETRATING SEALERS, BRIDGE

SUPERSTRUCTURE) (100% SILANE)

1080-0471 S6 Linear Foot 208.0000 N

PRESTRESSED CONCRETE PLANK BEAMS, 36" X 12"

1080-0473 S6 Linear Foot 38.0000 N

PRESTRESSED CONCRETE PLANK BEAMS, 48" X 12"

9000-0001 X Each 1.0000 N Proj

PRE-CONSTRUCTION AND POST-CONSTRUCTION INSPECTIONS

9000-0003 J Each 1.0000 N Proj

TYPE 31 NESTED THRIE-BEAM GUIDE RAIL (5-FT RADIUS)

9000-0007 J Each 1.0000 N Proj

TYPE 31 NESTED THRIE-BEAM GUIDE RAIL (5-FT RADIUS, EXTENDED)

9000-0008 K Each 1.0000 N Proj

CAP INLET

9000-0010 C1, E, F Square Yard 117.0000 N Std

PAVED DRIVES

9000-0012 J2 Linear Foot 230.0000 N Proj

TEMPORARY PEDESTRIAN BARRICADE

9000-0013 C1 Cubic Yard 53.0000 N Proj

OVEREXCAVATION AND BACKFILL WITH NO. 57 COARSE AGGREGATE

9000-0015 H Linear Foot 4.0000 N Proj

6" P.V.C. PIPE (SCHEDULE 40)

9000-0016 F Ton 27.0000 N Std

PAVED DRIVE AND SIDE ROAD OVERLAYS

9000-0051 X Each 1.0000 N Proj

TEMPORARY POLE AND GUY SUPPORT

9000-0101 H Each 1.0000 N Proj

TEMPORARY PUMP BYPASS SYSTEM

9000-0399 C1, M Cubic Yard 147.0000 N Std

STOCKPILING AND PLACING NATIVE STREAMBED MATERIAL

9000-0680 K2, S1 Square Yard 75.0000 N Std

ELASTOMER WATERPROOFING MEMBRANE ON BRIDGE DECKS

9000-0681 K2, S1 Square Yard 81.0000 N Std

SPRAY APPLIED LIQUID WATERPROOFING MEMBRANE SYSTEM ON OTHER SURFACES

9000-1037 C1, H Cubic Yard 5.0000 N Proj

FLOWABLE FILL

9000-3000 K Each 4.0000 N Std

DESIGN ADA CONCRETE CURB RAMP

Page 12 of 104October 21, 2026 13:49:45 PM

9000-5101 X Lump Sum 1.0000 N Std

ELECTRONIC TICKETING (E-TICKETING) FOR CONSTRUCTION AGGREGRATE

9000-5103 X Lump Sum 1.0000 N Std

ELECTRONIC TICKETING (E-TICKETING) FOR CONSTRUCTION CONCRETE

9000-6012 K Each 4.0000 N Std

CONSTRUCT CONCRETE CURB RAMPS AND SIDEWALKS (BY QUADRANT)

9203-0101 C1, M Lump Sum 1.0000 N Std

TEMPORARY EXCAVATION SUPPORT AND PROTECTIVE SYSTEM, S-43865

Page 13 of 104October 21, 2026 13:49:45 PM

SPECIAL PROVISIONS

Special Provision: G51A - a00051 APPLICABLE DESIGNATED SPECIAL PROVISIONS (STATE) Addendum:

Action:

Item(s) Associated:

Header:

APPLICABLE DESIGNATED SPECIAL PROVISIONS (STATE)

Provision Body:

APPLICABLE DESIGNATED SPECIAL PROVISIONS. The following Designated Special Provisions are found in Appendix C and apply to this bid proposal.

DSP4. Diverse Business (DB) Requirements for Non-Federally Funded Construction Projects.

DSP9. Special Supplement - Anti-Pollution Measures - August 26, 1999.

DSP15. Commonwealth Standard Terms and Conditions.

Project Specific Details:

Special Provision: G113B - a00113 CONTRACT PROVISIONS - RIGHT-TO-KNOW LAW Addendum:

CONTRACT PROVISIONS - RIGHT TO KNOW LAW

Provision Body:

I. Contract Provisions – Right to Know Law 8-K-1532

a. The Pennsylvania Right-to-Know Law (RTKL), 65 P.S. §§ 67.101-3104, applies to this Contract.

b. If the Department needs assistance in any matter arising out of the RTKL related to this Contract, the Department will notify the Contractor using the legal contact information provided in this Contract. The Contractor, at any time, may designate a different contact for such purpose upon reasonable prior written notice to the Department.

c. Upon written notification from the Department that it requires assistance in responding to a request under the RTKL for information related to this Contract that may be in the Contractor’s possession, constituting, or alleged to constitute, a public record in accordance with the RTKL (“Requested Information”), the Contractor will:

1. Provide the Department, within 10 calendar days after receipt of written notification, access to, and copies of, any document or information in the Contractor’s possession arising out of this Contract that the Department reasonably believes is Requested

Page 14 of 104October 21, 2026 13:49:45 PM

Information and may be a public record under the RTKL; and

2. Provide such other assistance as the Department may reasonably request, in order to comply with the RTKL with respect to this Contract.

d. If the Contractor considers the Requested Information to include a request for a Trade Secret or Confidential Proprietary Information, as those terms are defined by the RTKL, or other information that the Contractor considers exempt from production under the RTKL, notify the Department and provide, within 7 calendar days of receiving the written notification, a written statement signed by a representative of the Contractor explaining why the requested material is exempt from public disclosure under the RTKL.

e. The Department will rely upon the written statement from the Contractor in denying a RTKL request for the Requested Information unless the Department determines that the Requested Information is clearly not protected from disclosure under the RTKL. Should the Department determine that the Requested Information is clearly not exempt from disclosure, provide the Requested Information within 7 calendar days of receipt of written notification of the Department’s determination.

f. Failing to provide the Requested Information within the time period required by these provisions, indemnify and hold the Department harmless for any damages, penalties, costs, detriment or harm that the Department may incur as a result of this failure, including any statutory damages assessed against the Department.

g. The Department will reimburse the Contractor for any costs associated with complying with these provisions only to the extent allowed under the fee schedule established by the Office of Open Records or as otherwise provided by the RTKL if the fee schedule is inapplicable.

h. The Contractor may file a legal challenge to any Department decision to release a record to the public with the Office of Open Records, or in the Pennsylvania Courts, however, indemnify the Department for any legal expenses incurred by the Department as a result of such a challenge and hold the Department harmless for any damages, penalties, costs, detriment or harm that the Department may incur as a result of the failure, including any statutory damages assessed against the Department, regardless of the outcome of such legal challenge. As between the parties, agree to waive all rights or remedies that may be available as a result of the Department’s disclosure of Requested information pursuant to the RTKL.

i. The Contractor’s duties relating to the RTKL are continuing duties that survive the expiration of this Contract and continue as long as the Requested Information remains in the Contractor's possession.

Special Provision: C171A - a00171 CHANGES TO SPECIFICATIONS: SECTIONS 313, 314, 360, 410, 412, and 413

Addendum:

CHANGES TO SPECIFICATIONS: SECTIONS 313, 314, 360, 410, 412, and 413

Provision Body:

SECTION 313—SUPERPAVE ASPHALT MIXTURE DESIGN, STANDARD CONSTRUCTION, BASE COURSE

Section 313.3(m) Tests for Depth. Revise to read as follows:•

(m) Tests for Depth.

(m) Tests for Depth. Replace with the following:

Page 15 of 104October 21, 2026 13:49:45 PM

Control the loose depth of each layer to construct the base course to the compacted depth indicated and within the specified tolerance. On the top lift and in the presence of the Inspector, drill full-depth cores at one random location selected by the Inspector according to PTM No. 1 in each 3,000 square yards of completed base course and at other locations the Inspector suspects are deficient. After the Inspector completes depth measurements, backfill, compact, and seal core holes with the mixture used to construct the course.

The Inspector will measure the full-depth cores according to PTM No. 737. Pavement deficient in depth by 1/2 inch or more and that cannot be satisfactorily corrected is defective. Immediately delineate the limits of pavement deficient in depth from the core location by proceeding longitudinally, forward and backward, obtaining additional pavement cores every 50 feet until the depth is less than 1/2 inch deficient of the design depth. The defective course will be the full width of the affected lane.

SECTION 314—SUPERPAVE ASPHALT MIXTURE DESIGN, STANDARD CONSTRUCTION, ASPHALT RICH BASE COURSE

Section 314.3(m) Tests for Depth. Revise to read as follows:•

(m) Tests for Depth.

(m) Tests for Depth. Replace with the following:

Control the loose depth of each layer to construct the ARBC to the compacted depth indicated and within the specified tolerance. In the presence of the Inspector, drill full-depth cores at one random location selected by the Inspector according to PTM No. 1 in each 3,000 square yards of completed ARBC and at other locations the Inspector suspects are deficient. After the Inspector completes depth measurements, backfill, compact, and seal core holes with ARBC.

The Inspector will measure the full-depth cores according to PTM No. 737. Pavement deficient in depth by 1/2 inch or more and that cannot be satisfactorily corrected is defective. Immediately delineate the limits of pavement deficient in depth from the core location by proceeding longitudinally, forward and backward, obtaining additional pavement cores every 50 feet until the depth is less than 1/2 inch deficient of the design depth. The defective course will be the full width of the affected lane.

SECTION 360—ASPHALT TREATED PERMEABLE BASE COURSE

Section 360.2(e)3. Production. Revise to read as follows:•

3. Production. During the first day of production, take at least three asphalt content and gradation tests to verify the mixture conforms to the JMF. After the first day, perform tests for asphalt content and aggregate gradation according to the QC Plan and PTM No. 1. Produce ATPBC conforming to the gradation requirements in Table A and with an asphalt content within 0.8% of the JMF (n=1). Ensure the aggregate is uniformly coated with asphalt and no runoff of excess asphalt is observed.

Section 360.3(m). Tests for Depth. Revise to read as follows:•

(m) Tests for Depth: Binder and Wearing Courses. Replace with the following:

Carefully dig or drill one random 6-inch diameter test hole selected by the Representative according to PTM No. 1 to the full depth of the ATPBC for each 3,000 square yards, or less, of completed base course. The Representative may require additional test holes in areas the Representative suspects are deficient in depth. The Representative will measure the depth of the base course. Using material acceptable to the Representative, backfill the test holes and compact the material to fill the test hole flush with the completed base course.

ATPBC deficient in depth by 1/2 inch or more is defective. Immediately delineate the limits of ATPBC deficient in depth from the location by proceeding longitudinally, forward and backward, obtaining additional test holes every 50 feet until the depth is less than 1/2 inch deficient of the indicated depth. The defective course will be the full width of the affected lane.

SECTION 410—SUPERPAVE MIXTURE DESIGN, STANDARD AND RPS CONSTRUCTION OF PLANT-MIXED ASPHALT FINE-

GRADED COURSES

Section 410.3. CONSTRUCTION. Revise to read as follows:•

410.3 CONSTRUCTION—Section 413.3 using the test procedures, limits, and tolerances for a 9.5 mm nominal maximum aggregate size mixture except where procedures, limits and tolerances are specifically indicated for a 9.5 mm fine-graded nominal maximum aggregate size mixture and as modified as follows:

Revise Table G to include 9.5 mm Fine Grade Wearing Course as follows:

Page 16 of 104October 21, 2026 13:49:45 PM

TABLE G

Mixture Minimum Indicated Compacted Depths

Mixture Minimum Depth

9.5 mm Fine Grade Wearing Course 1 inch

SECTION 412—SUPERPAVE MIXTURE DESIGN, CONSTRUCTION OF PLANT-MIXED 6.3 MM ASPHALT OVERLAY COURSES

Section 412.3(a)2. Preplacement Meeting. Revise to read as follows:•

2. Preplacement Meeting. At least 2 weeks before placing asphalt paving mixtures, schedule an asphalt preplacement meeting with the Representative to review at a minimum the specification, paving operation QC Plan, sequence of paving operations, asphalt mixture temperature checks, mixture acceptance, density acceptance and the care and custody of asphalt acceptance samples.

Section 412.3(h)1.a. Placing. Revise to read as follows:•

1.a Placing. Unless otherwise allowed, deliver, place, and compact 6.3 mm paving mixtures during daylight hours. Ensure the mixture does not contain lumps of cold material. Deliver and place 6.3 mm paving mixtures at the laying temperatures specified in Table B.

Material placed outside the temperature limits as specified in Table B is defective.

Utilize a Material Transfer Vehicle (MTV) as specified in Section 108.05(c)5 for 6.3 mm paving mixtures unless otherwise approved by the Representative.

Section 412.4(a)4.b. Dispute Resolution. Revise TABLE H to read as follows:•

TABLE H

Dispute Resolution Retest Cost Table

Test Method

Mixture Acceptance Retest Cost if Retest Results Indicate

100% Pay Factor(s) for Full Lots (n > 3)* or Single Sample (n=1) Requirements in Table B were met for Partial Lots (n < 3)**

Mixture Acceptance Retest Cost if Retest Results Indicate

< 100% Pay Factor(s) for Full Lots (n > 3)* or Single Sample (n=1) Requirements in Table B were not met for Partial Lots (n < 3)**

PTM No.

702/739 $900 $3,500

PTM No. 757 $500 $2,000

* For full lots (n ≥ 3) where the original test results indicated a defective lot, only the pay factor(s) where original test results indicated a defective lot for asphalt content or percent passing the 75 μm (No. 200) sieve will be utilized to determine the retest cost.

** For partial lots (n < 3) where the original test results indicated a pay parameter (asphalt content, percent passing the 75 µm (No. 200) sieve, or both) did not meet the Single Sample (n = 1) requirements in Table B, only the pay parameter(s) that did not meet the Single Sample (n =1) requirements will be utilized to determine the retest cost.

SECTION 413—SUPERPAVE MIXTURE DESIGN, STANDARD AND RPS CONSTRUCTION OF PLANT-MIXED ASPHALT

COURSES WITH PERCENT WITHIN LIMITS AND LTS TESTING (PWS-LTS)

Section 413.2(e)1. Recycled Asphalt Material. Revise to read as follows:•

1. Virgin Material Mixtures. Size, uniformly grade, and combine aggregate fractions, asphalt binder, and either WMA Technology

Page 17 of 104October 21, 2026 13:49:45 PM additive(s) or modifier(s) in proportions to produce a JMF that conforms to the material, gradation, and volumetric Superpave Asphalt Mixture Design requirements according to Bulletin 27, Chapter 2A. Produce an asphalt mixture for the specified nominal maximum aggregate size and design ESALs except as procedurally modified by the WMA Technology Manufacturer Technical Representative (Technical Representative) to address laboratory procedures when preparing, compacting and testing asphalt mixtures to achieve a uniform blend. Special additive(s) or modifier(s) need not be used if mixture temperature, workability, and compaction can be achieved solely through plant mechanical modification to produce foamed asphalt. Do not incorporate the WMA Technology additive, modifier or process during the volumetric asphalt mixture design process, so that the JMF volumetrics and material percentages are based on a mixture with no WMA Technology. Only use the WMA Technology additive, modifier or process to evaluate results from moisture susceptibility testing during the mix design process. Develop an asphalt mixture JMF, then incorporate the WMA Technology additive, modifier, or process into that JMF during production. Create an asphalt JMF cover sheet (Form TR-448A) for approval containing the WMA Technology used, additive dosage rate or percent water added for foaming, material code, and the TSR data from the moisture susceptibility testing.

Submit a copy of each completed JMF, signed by a certified Asphalt Level 2 plant technician, to the DME/DMM at least 3 weeks before the planned start of mixture production. Include a list of all material sources and the asphalt mixture producer in the JMF.

Provide the calibration factors (Cf and 200 Cf) according to PTM No. 757 with the JMF. Do not start mixture production until after the DME/DMM reviews the JMF.

Submit a new JMF with a change in material sources or if a new JMF is necessary to produce a mixture conforming to this specification.

No additional revisions were made to Section 413.2(e)1.•

Section 413.2(e)1.d.5. Volumetric Analysis of Compacted Specimens. Revise TABLE A as follows:•

TABLE A

Job-Mix Formula Composition Tolerance Requirements of the Completed Mix

Single Sample (n=1) Multiple

Samples (n > 3)

Gradation Passing 12.5 mm (1/2 inch) and Larger Sieves +8% +6% Passing 9.5 mm (3/8 inch) to 150 µm (No. 100) Sieves (Inclusive) +6% +4%

Passing 75 µm (No. 200) Sieve +3.0% +2.0% Asphalt Content

19.0 mm Asphalt mixtures and smaller +0.7% +0.4%

25.0 mm Asphalt mixtures and larger +0.8% +0.5%

Temperature of Mixture (F)

Class of Material

Type of Material

Chemical, Organic, Foaming Additives

Minimum*

Mechanical Foaming Equipment/Process

Minimum* Maximum*

PG 58S-28 Asphalt Binder 215 230 310 PG 64S-22 Asphalt Binder 220 240 320 PG 64E-22 Asphalt Binder 240 260 330

All other Binders Asphalt Binder

The higher of 215 or the minimum temp.

specified in Bulletin 25 minus 45F

The higher of 230 or the minimum temp.

specified in Bulletin 25 minus 30F

As specified in Bulletin

* Outline in the Producer QC Plan and follow more restrictive temperature requirements provided by the WMA technology manufacturer or Technical Representative(s) for production and placement of the mixture. Determine the SGC compaction temperature for the production QC which yields the same target air voids as the designed JMF. Include the SGC compaction temperature in the

Page 18 of 104October 21, 2026 13:49:45 PM

Producer QC Plan. Compact the completed mixture in the SGC for QC volumetric analysis at the SGC compaction temperature according to the guidelines provided by the Technical Representative.

Section 413.2(i)2. Certification Acceptance. Revise to read as follows:•

2. Certification Acceptance. Acceptance by certification is appropriate for the following mixtures, conditions, or applications:

Scratch courses, leveling courses less than 2-inch depth and driveway adjustments.•

Mixtures used by Department maintenance forces.•

Mixtures purchased by local or municipal governments.•

Mixtures placed in quantities not exceeding 500 tons in a continuous placement operation unless otherwise directed by the Representative.

Mixtures used for parking lots.•

All 4.75 mm NMAS asphalt mixtures.•

Other mixtures, conditions, or applications as approved by the Representative.•

2.a General. Obtain certification from the mixture Producer. Use all QC tests during mixture production as acceptance tests. Certify mixtures using Form CS-4171B. Include, or attach, the QC test results on the form. Provide the form to the Inspector-in-Charge within 1 working day after completing the QC tests. Certify mixtures as specified in Section 106.03(b)3 and the requirements below.

2.b Certification of Mixture. Certify each mixture daily if QC test results conform to the single sample and multiple sample JMF production tolerances of Table A. The acceptance values will be:

Asphalt Content.•

Percent Passing the 2.36 mm (No. 8) sieve (not applicable for 4.75 mm NMAS asphalt mixtures).•

Percent Passing the 75 µm (No. 200) sieve.•

If using printed ticket results in place of laboratory test results for asphalt content, certify that at least 90% of each day’s printed ticket results for asphalt content are within 0.2 percentage points of the JMF.

If the mixture does not conform to the above requirements, do not certify the mixture. Instead, provide all QC test results to the Inspector-in-Charge. If using printed ticket results for asphalt content, provide the percentage of daily printed ticket results within 0.2 percentage points of the JMF to the Inspector-in-Charge. Payment will be determined according to Table H based on the QC test results.

If a day’s production is interrupted by corrective action, material produced after the corrective action may be certified if QC test results conform to production tolerances.

2.c Maintaining Approval to Certify Mixtures. The Department may suspend a plant’s approval to certify mixtures if QC is not performed according to the Producer QC Plan, mixtures are not produced according to Bulletin 27, a mixture cannot be certified on 2 consecutive production days, or as described below.

The Department may take IA samples of the completed mixture at the plant. In the presence of the Department, test the IA samples for asphalt content and gradation according to the test methods indicated in the Producer QC Plan. Take immediate corrective actions if the mixture does not conform to Table A.

The Department may take QA samples of the completed mixture at the plant or on the roadway directly from the uncompacted mixture placed by the paving equipment specified in Section 413.3(e). The Department will test QA samples according to PTM No. 757 or PTM No. 702, Modified Method D, if previously identified problematic aggregates are used in the mixture, for conformance to Table A. If the results of the QA samples do not comply with Table A, review the Producer QC Plan and the QC test results that followed the QA samples for conformance to Table A. If QC results do not conform to Table A, perform the corrective actions necessary to provide a mixture conforming to Table A.

After completing corrective actions or the sample review, the Department will perform an on-site evaluation of the Producer’s plant operation and QC and then take a sample of the completed mixture at the plant. In the presence of the Representative, test the sample.

Page 19 of 104October 21, 2026 13:49:45 PM

If the sample does not comply with Table A, the Department will suspend certification. Immediately suspend shipping mixtures accepted by certification to the project.

After testing verifies that the produced mixture conforms to Tables A and B and with the Representative present, conduct JMF verification according to the Producer QC Plan. After successfully completing JMF verification, resume both certification and shipping mixtures accepted by certification to the project.

Section 413.3(a)2. Preplacement Meeting. Revise to read as follows:•

2. Preplacement Meeting. At least 2 weeks before placing asphalt paving mixtures, schedule an asphalt preplacement meeting with the Representative to review at a minimum the specification, paving operation QC Plan, sequence of paving operations, asphalt mixture temperature checks, mixture acceptance, density acceptance and the care and custody of asphalt acceptance samples.

Section 413.3(d). Hauling Equipment. Revise to read as follows:•

(d) Hauling Equipment. Haul the mixtures in tightly sealed vehicles that do not contain petroleum oils, solvents, or other materials that adversely affect asphalt mixture. Provide covers of sufficient size and quality to protect the entire load under all conditions.

Maintain the proper and uniform placement temperature as specified in Section 413.3(h)1. Provide insulation on all sides of the truck body, a double-walled truck body, or a heated truck body when the air temperature is below 50F from October 1 to April 30. Provide a 3/8-inch diameter hole near the center and approximately two-thirds the distance down from the top of the vehicular box, on both sides, to allow for asphalt mixture temperature checks. If trucks cannot be provided with these holes, provide the Representative with two infrared temperature devices along with documentation that the devices were verified annually through an independent verification service or with a blackbody calibration block before paving for asphalt mixture temperature checks.

Section 413.3(f). Rollers. Revise to read as follows:•

(f) Rollers. Use steel wheel, pneumatic tire, vibratory, or oscillating rollers as specified in Sections 108.05(c)3.a, 3.b, 3.c, 3.e, 3.f, 3.h, or (c)4. Operate rollers according to manufacturer's recommendations. Use vibratory and oscillating rollers with separate controls for frequency and amplitude.

Section 413.3(h)1.a. Placing. Revise to read as follows:•

1.a Placing. Unless otherwise allowed or indicated, deliver, place, and compact asphalt paving mixtures during daylight hours.

Ensure the mixture does not contain lumps of cold material. Deliver and place mixtures at the laying temperatures specified in Table A for the type and class of material used. Do not incorporate any material delivered outside the temperature limits as specified in Table A. Material placed outside the temperature limits as specified in Table A is defective.

Utilize a Material Transfer Vehicle (MTV) as specified in Section 108.05(c)5 for RPS pavements unless otherwise approved by the Representative.

Section 413.3(h)1.e. Safety Edge. Revise to read as follows:•

1.e. Safety Edge. Construct the Safety Edge as the standard edge treatment on the outside edge of asphalt pavements and shoulders. Use the Safety Edge for both wearing and binder courses with a depth of 1.5 inches or greater. Do not place the Safety Edge at total depths greater than 5 inches. The Safety Edge is not required where curb or sidewalk are encountered or where the face of guiderail is directly over the edge of pavements. Do not place the Safety Edge for base, leveling, or scratch courses.

Construct the Safety Edge with the same material used to construct the roadway course being placed or, if specified, the paved shoulders. Attach a device to the paver to confine material at the end gate and extrude the asphalt material in a wedge shape. Use an adjustable device that allows the operator to vary the slope extruded at the paver to account for the angle becoming steeper during compaction (roll up). Before construction, the Safety Edge device must be approved by the Representative(s).

Compact the roadway or paved shoulder as required by the specifications. Do not delay rolling of the mat adjacent to the Safety Edge. After compaction of the mat is complete, provide a Safety Edge meeting the final shape requirements as shown on the Standard Drawings. The completed angle of the Safety Edge must be 26 degrees to 40 degrees measured from the pavement cross slope extended. At the beginning of each day’s paving, measure the angle of the Safety Edge from the pavement cross slope extended. Perform measurements after final compaction is complete. If the angle of the Safety Edge does not meet the slope requirements, stop paving, and provide corrective action. Do not resume production paving until final shape requirements of Safety Edge are achieved.

Allow automatic transition to intersections, driveways, guiderail sections, and obstructions.

Page 20 of 104October 21, 2026 13:49:45 PM

Use the device to constrain the asphalt head, reducing the area and increasing the density of the extruded profile. A single plate strike-off method is not allowed. Do not place the Safety Edge on organic material.

Section 413.3(h)2.a.1. Partially Completed Lots (n=2 or less). Revise to read as follows:•

2.a.1 Partially Completed Lots (n=2 or less). When process conditions change to an extent that a partially completed lot cannot be combined with the most recently completed lot, samples will be independently evaluated on the partially completed lot. For asphalt content and percent passing the 75 μm (No. 200) sieve, mixture acceptance samples will be evaluated individually as specified in Section 413.2(e), Table A (n=1) criteria. For density, mat density acceptance samples will be evaluated individually using the criteria in Table E.

If samples tested for asphalt content and percent passing the 75 μm (No. 200) sieve meet the n=1 criteria of Table A, and samples tested for density meet the criteria in Table E, payment will be 100% of the contract unit price. If samples tested for asphalt content and percent passing the 75 μm (No. 200) sieve do not meet the n=1 criteria of Table A, the material will be considered defective. If samples tested for density are no more than 2.0% below the minimum or no more than 2.0% above the maximum limits of Table E, payment will be 90% of the contract unit price. If samples for density are more than 2.0% below the minimum or more than 2.0% above the maximum limits of Table E, the pavement will be considered defective.

Unless otherwise directed in writing by the District Executive, remove and replace defective work.

No additional revisions were made to Section 413.3(h)2.a.1.•

Section 413.3(h)2.c.1. LTS Testing. Revise to read as follows:•

2.c.1 LTS Testing. The LTS will test the mixture acceptance samples according to PTM No. 757 or PTM No. 702, Modified Method D and PTM No. 739, if previously identified problematic aggregates are used in the mixture, to determine asphalt content and the percent passing the 75 μm (No. 200) sieve. The LTS will use the calibration factors (Cf and 200 Cf) provided with the JMF for PTM No. 757. For individual increment test results outside of the single sample (n=1) tolerances in Table A, the LTS will analyze the test results for extreme values according to PTM No. 4 at the 5% significance level. If discarding an extreme value reduces a lot to less than three remaining test results, the Department will accept the lot as specified in Section 413.3(h)2.a.1. The Department will accept lots with three or more test results as specified in Section 413.4(a)4 or Section 413.4(b).

If the asphalt content or the percent passing the 75 μm (No. 200) sieve is not within the single sample (n=1) or multiple sample (n≥3) tolerances in Table A for two consecutive lots or a total of three lots, stop all production of the JMF. Determine the cause of the problem and provide a proposed solution to the Department.

Do not resume production of the JMF until the Representative reviews the proposed solution and authorizes production to continue.

The LTS will test Gmm verification samples as specified in Section 413.3(j)4.d.

Section 413.3(j)4.a. General. Revise to read as follows:•

4.a General. Pavement cores are required for accepting the density of RPS construction. Pavement cores are required for standard construction of extended-season paving, unless waived by the Representative as specified in Section 413.3(b)1. Pavement cores are appropriate for accepting the density of standard construction if all the following materials, conditions, or applications exist:

Materials placed at indicated compacted depths greater than or equal to the minimum depths specified in Table G.•

Materials placed on stable and uniform bases.•

TABLE G

Mixture Minimum Indicated Compacted Depths

Mixture Minimum Depth

9.5 mm Wearing Course 1 1/2 in.

12.5 mm Wearing Course 2 in.

19 mm Binder Course 2 1/2 in.

25 mm Binder Course 3 in.

Page 21 of 104October 21, 2026 13:49:45 PM

Section 413.3(m). Tests for Depth: Binder and Wearing Courses. Revise to read as follows:•

(m) Tests for Depth: Binder and Wearing Courses. Construct the pavement to the depth indicated and within the specified tolerances.

For courses with a designed course depth and density acceptance by non-movement or optimum rolling pattern, the Inspector will calculate the weight per square yard for verification of yield. If yield results indicate insufficient course depth, drill one 6-inch diameter core for each 500 tons of material placed to determine the extent of the deficient depth as defined below. Core locations will be determined according to PTM No. 1.

For courses with density acceptance by lots, the inspector will measure the depth of each sublot according to PTM No. 737 using the density acceptance samples. After the Inspector completes depth measurements, backfill, compact, and seal core holes with the mixture used to construct the course. Deficient depth core(s) resulting in defective work should not be submitted for density acceptance testing. Once the defective work has been removed and replaced, obtain a new density acceptance sample for the sublot(s) as specified in Section 413.3(j)4.c.

Pavement deficient in depth by more than 1/8 inch in three or more adjacent acceptance core locations is defective. The extent of the defective work is the entirety of all sublots represented by the adjacent deficient acceptance core samples. The defective course will be the full width of the affected lane.

Pavement deficient in depth by more than 1/4 inch at a single acceptance core location is defective. Immediately delineate the limits of pavement deficient in depth from the acceptance core location by proceeding longitudinally, forward and backward, obtaining additional pavement cores every 50 feet until the depth is within 1/4 inch of the design depth. The defective course will be the full width of the affected lane.

Section 413.3(o). Defective Work. Revise to read as follows:•

(o) Defective Work. As specified in Section 105.12 and as follows:

Department acceptance and QA testing will not relieve the Contractor of responsibility for material or work that the Representative determines is defective before the Department issues the acceptance certificate. Remove and replace or repair defective work as directed.

The BOCM, CQAD will review Representative determinations of defective material or work.

Remove and replace pavement defective for temperature as specified in Section 413.3(h)1.a. for pattern segregation as specified in Section 413.3(h)3, for flushing as specified in Section 413.3(h)4, surface tolerance as specified in Section 413.3(l) or Section 313.3(l) and depth as specified in Section 413.3(m), or Section 313.3(m). Remove and replace pavement defective for percent within limits or Payment Factor Percentages as specified in Tables H and I.

Special Provision: C172A - a00172 CHANGES TO SPECIFICATIONS: SECTIONS 107, 871, 872, 875, and 876

Addendum:

CHANGES TO SPECIFICATIONS: SECTIONS 107, 871, 872, 875, and 876

Provision Body:

SECTION 107—LEGAL RELATIONS AND RESPONSIBILITY TO THE PUBLIC

Section 107.28 EROSION AND SEDIMENT POLLUTION CONTROL PLANS AND PERMITS. Revise to read as follows:•

Page 22 of 104October 21, 2026 13:49:45 PM

107.28 EROSION AND SEDIMENT POLLUTION CONTROL PLANS AND PERMITS—Install and maintain erosion and sediment (E&S) pollution control…