NAVSEA_PD-87066C.pdf

NAVSEA PD-87066C

CAGE Code 32263 28 July 2021

SUPERSEDING

NAVSEA PD-87066B

14 August 2017

PURCHASE DESCRIPTION

GLOVES, CHEMICAL AND OIL PROTECTIVE

This purchase description is approved for use by the Department of the Navy.

1. SCOPE

1.1. Scope. This specification covers the requirements for 15 mil unsupported, dipped rubber chemical and oil protective gloves, with a cotton-flock lining.

1.2. Classification. The gloves are available in one type and in the following sizes as specified

(see 6.2):

Schedule of Sizes 7, 8, 9, 10, 11

2. APPLICABLE DOCUMENTS

2.1. General. The documents listed in this section are specified in sections 3 and 4 of this purchase description. This section does not include documents cited in other sections of this purchase description or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this purchase description, whether or not they are listed.

2.2. Government documents.

2.2.1. Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2).

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-DTL-32075 - Label: For Clothing, Equipage and Tentage (General Use)

(Copies of this document are available from https://quicksearch.dla.mil.)

AMSC N/A FSC 8415

DISTRIBUTION A: Approved for public release.

INCH POUND

https://quicksearch.dla.mil/

2.3. Non-Government publications. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2).

AMERICAN SOCIETY FOR QUALITY (ASQ)

ANSI/ASQ-Z1.4 - Procedures, Sampling and Tables for Inspection by Attributes

(Copies of this document are available from https://www.asq.org.)

ASTM INTERNATIONAL

ASTM D297 - Standard Test Methods for Rubber Products – Chemical Analysis ASTM D412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic

Elastomers – Tension ASTM D573 - Standard Test Method for Rubber – Deterioration in an Air Oven ASTM D3767 - Standard Practice for Rubber – Measurement of Dimensions

(Copies of these documents are available from https://www.astm.org.)

2.4. Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 First article. When specified (see 6.2 and 6.3) a sample shall be subjected to first article inspection in accordance with 4.2.

3.2 Design. The gloves shall be 15 mil unsupported, dipped rubber gloves of a standard four finger and thumb style, with a cotton-flock lining and either a pinked, natural dipped or rolled bottom cuff edge (see Figure 1).

3.3 Figures. Figures are furnished for information purposes only. When inconsistencies exist between the written specification and the figures, the written specification shall govern.

3.4 Materials.

3.4.1 Rubber Compounds. The gloves shall be made of carboxylated butadiene-acrylonitrile rubber latex, suitably compounded without the use of plasticizers or inert fillers and vulcanized to meet the requirements specified herein.

3.4.1.1 Color. Unless otherwise specified by the procuring activity, the approved color of the finished gloves shall be white or in light shades of green or blue.

3.4.2 Lining. Each finished glove shall have a cotton flock lining suitably adhered to the rubber compound on the inside.

https://www.asq.org./ https://www.astm.org./

3.5 Construction.

3.5.1 Dipping forms. The dipping forms utilized by the contractor in his manufacturing process may be made from any commercially designed mold; however, the gripping surface of the finished glove (palm and fingers) shall have a non-slip embossed pattern design.

3.5.2 Chlorination. The rubber surfaces of each finished glove may be chlorinated if required to reduce tackiness. Excessive chlorination shall be avoided to prevent excessive stiffening, discoloration, or slipperiness.

3.5.3 Label. Each finished glove shall have a Type IV, Class 14 label of MIL-DTL-32075 containing a combination identification and cautionary statement inscription, centered on write of palm side with bottom of label approximately 2 inches from the bottom edge of the cuff. Label shall not appear anywhere in the palm area of the glove. The size of the lettering for the identification information shall not be less than 1/8 inch in height. The cautionary statement “FOR PROTECTION AGAINST USN OTTO FUEL, DO NOT REUSE” shall be printed in larger letter than all of the other lettering in the label.

3.6 Finished measurements. The sizes and measurements of the finished gloves shall conform to the dimensions as specified in Table I. All measurements and tolerances are expressed in inches.

TABLE I – Finished measurements

Measurement

Size Tolerance 7 8 9 10 11

Overall Length (A) 12½ 12½ 12½ 12½ 12½ Minimum

Width of palm (B) 3½ 4 4½ 5 5½ ± ¼

Thickness: Cuff (C), Palm

(D) and Fingertip (E)

0.013

Minimum

3.7 Physical and chemical requirements. The finished gloves shall conform to the physical requirements shown in Table II when tested as specified in 4.3.5.

TABLE II – Physical and Chemical Requirements of Finished Gloves

Characteristic

Requirement, minimum

Tensile strength, psi, original 2000 Porosity, original Pass 1/ Resistance to Otto Fuel penetration, original Pass 2/ Resistance to Otto Fuel penetration, after aging Pass 2/

1/There shall be no evidence of air bubbles.

2/There shall be no evidence of Otto Fuel penetration.

3.7.1 Resistance to Otto Fuel penetration. The gloves shall be resistant to Otto Fuel penetration. There shall be no evidence of Otto Fuel penetration. A failure of this test shall be cause for rejection of the lot.

3.7.2 Resistance to Otto Fuel penetration after aging. To determine shelf-life viability, test will be repeated after aging. There shall be no evidence of Otto Fuel penetration. A failure of this test shall be cause for rejection of the lot.

3.8 Workmanship. The finished gloves shall conform to the quality established by this specification. The occurrence of defects cited in Table V shall not exceed the acceptance quality levels specified in the contract.

4. VERIFICATION

4.1. Classification of inspection. The inspection requirements specified herein are classified as follows:

a. First article inspection. (See 4.2).

b. Conformance inspection. (See 4.3).

4.2. First article inspection. The first article submitted in accordance with 3.1, 6.2 and 6.3, shall be inspected as specified in Table III. Failure to meet the first article requirements shall be cause for rejection of the first article lot.

TABLE III - First article inspection

Paragraph

Inspection Requirement Method Materials verification 3.4.1 4.3.5, Table VI Visual examination 3.2 through 3.5 4.3.4.1 Dimensional examination 3.6 4.3.4.2 End item testing 3.7 4.3.5, Table VI

4.2.1. First article units. For Otto Fuel penetration resistance testing, the sample size shall be two pair of gloves for each size ordered. Unless otherwise specified in the solicitation or contract the number of samples shall be four pairs of gloves for each size ordered for the remaining tests.

4.3. Conformance inspection. Conformance inspection shall consist of the verifications specified in Table IV. Failure to meet the verification requirements shall be cause for rejection of the lot.

TABLE IV - Conformance inspection

Paragraph Inspection Requirement Method Visual examination 3.2 through 3.5 4.3.4.1 Dimensional examination 3.6 4.3.4.2 Porosity 3.7, Table II 4.3.5, Table VI Resistance to Otto Fuel penetration, original 3.7, Table II 4.3.5, Table VI Resistance to Otto Fuel penetration, after aging 3.7, Table II 4.3.5, Table VI

4.3.1. Conformance inspection samples. The sampling for inspection shall be performed in accordance with ANSI/ASQ Z1.4 for visual and dimensional conformance. For Otto Fuel penetration resistance testing, the sample size shall be two pair of gloves for each size ordered per lot.

4.3.2. Production lot. Each production lot shall contain only one size of gloves. The lot size shall be no greater than 10,000 pairs of gloves.

4.3.3. In-process inspection. Visual and dimensional examinations shall be made at any point or during any phase of the manufacturing process to determine whether construction details which cannot be examined in the finished product are in accordance with requirements specified in Section 3. Materials and components, which can be classified as having a defect in accordance with Table V, shall be removed from production.

4.3.4. End item verification.

4.3.4.1. Visual and dimensional examination. The gloves selected for end item verification shall be visually and dimensionally examined for the defects listed in Table V.

TABLE V - Classification of end item visual and dimensional defects

Examine Defect Classification

Critical Major Minor Pairing Gloves not mated in pairs e.g., two left, two right gloves submitted as a pair 1

Gloves submitted as a pair not the same size

Paired gloves not the same in color or appearance

Design Any characteristic not in accordance with specified requirements (unless otherwise classified herein)

Color Not as specified (see 3.4.1.1) 202

Not uniform throughout glove 203 Cleanliness Grease, dirt or oil stain on glove which cannot be easily removed

Not clean, i.e., dirty, but dirt can be easily removed

Dimensional (see 4.3.3.2)

Any finished glove dimension not within the specified tolerance

Construction and Workmanship (applicable to inside and outside of the glove)

Any cut, hole, tear, rip or rupture through material 2

Evidence of improper vulcanization, e.g., tackiness

Any repair or patch 106

TABLE V - Classification of end item visual and dimensional defects continued

Examine Defect Classification Critical Major Minor

Construction and Workmanship

(applicable to inside and outside of the glove)

-continued

Any blister, open or closed 107

Any pinch, thin spot, pit, abraded area, deep crease, or similar defect less than minimum thickness allowed

Any burned spot

Any malformation or distortion affecting serviceability

Embossing not as specified (see 3.5.1)

Any solid rubber ridge, run or lump 205 Bottom open edge of glove not constructed as specified

Bottom open edge of glove crooked or loose, if rolled edge

Cotton Flocking omitted on inside of glove

Marking Missing, incorrect or illegible 114

Misplaced, height of characters not as specified, or not accomplished as specified

Not permanent, i.e., can be easily rubbed off with a moistened thumb

4.3.4.2. End item dimensional examination. The end items shall be examined for conformance to the dimensions specified in 3.6, Table I as specified below and in 4.3.5, Table VI (for thickness).

Any dimension not within the specified tolerance shall be classified as Major 104. All measurements shall be taken with the glove flattened without pulling or stretching. For A through E refer to Figure 1.

A. Measurement shall be taken on back side from tip of second finger to the open (cuff) edge of glove.

B. Measurement shall be taken across the palm at thumb crotch with thumb folded back, folded edge to folded edge, on a line parallel to the open (cuff) edge of glove. The thumb’s rubber material shall not be stressed after thumb is folded back onto the glove.

C. Measurement shall be taken at the centerline of the glove approximately two inches above the open (cuff) edge of the glove.

D. Measurement shall be taken at the centerline of the glove at or above the thumb crotch.

E. Measurement shall be taken at the midline of the inside of the middle finger approximately one inch from the tip.

4.3.5. End item testing.

TABLE VI – End item testing

Characteristic Requirement

Paragraph Test Method Results Reported As

Material Verification 3.4.1 ASTM D297 “Pass” or “Fail”

Thickness: Cuff, palm, and fingertip

3.6

ASTM D3767

Per method

Tensile strength, Original 3.7 ASTM D412 Per method 1/

Porosity, Original

3.7

4.3.5.1

“Pass” or “Fail”

Resistance to penetration by Otto

Fuel, Original

3.7

4.3.5.2

Resistance to penetration by Otto Fuel, After aging

3.7 ASTM D573 2/

4.3.5.2

1/Test report shall contain the individual values used to determine final result.

2/ The specimen shall be aged at a temperature of 158±1.8°F for 166±1 hours.

4.3.5.1 Porosity.

4.3.5.1.1 Test apparatus. The test apparatus shall be of a mechanism as described below or any other similar type in principle, provided the results can be obtained as specified in 4.3.5.1.2. A hollow shank, 3 inches in length, tapered on the outer surface to fit the open end of the rubber glove and a steel ring tapered on the inner surface to fit over the wooden shank shall be used.

The shank shall be attached to a steel base plate to make an airtight joint, and the tapered ring shall be bolted to the base plate so that it can be tightened over the shank. The base plate shall be fitted with ¼ inch internal pipe size brass nipple which shall be connected with other pipe fittings to mount a tire inflation valve; an air pressure gauge and a pressure relief valve (see Figure 2).

4.3.5.1.2 Procedure. The open end of the rubber glove shall be pulled over the shank of the test apparatus and clamped firmly in place by tightening the steel ring against the base plate.

Compressed air shall be fed into the glove to a pressure of 0.50 ±0.25 psi. The pressurized glove shall be immersed in water for one minute for observation of porosity as indicated by air bubbles.

No visible air bubbles shall be permitted within the one minute period.

4.3.5.2 Otto Fuel penetration resistance test. Evidence of Otto Fuel penetration shall be reported as a failure. A failure of this test shall be cause for rejection of the lot. Finished gloves selected for resistance to Otto Fuel penetration testing will be tested at Naval Undersea Warfare Center Division, Keyport.

5. PACKAGING

5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by Inventory Control Point’s packaging activity within the Military Service or Defense Agency or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products or by contacting the responsible packaging activity.

6. NOTES

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)

6.1 Intended use. The glove is a critical application item intended to protect torpedo handlers from exposure to Otto Fuel. Otto Fuel is fuel used in torpedoes which is comprised of propylene glycol dinitrate, dibutyl sebacate and 2-nitrodiphenylamine.

6.2 Acquisition documents. Acquisition documents should specify the following:

a. Title, number, and date of this specification, including any amendments.

b. Size (see 1.2).

c. National stock number(s)

d. When first article is required (see 3.1).

e. Number of first article inspection samples (see 4.2.1).

f. First article tests required (see 4.2).

g. Name and address of the first inspection facility; and the name and address of the

Government activity responsible for conducting the first article inspection program.

h. Packaging required (see 5.1)

i. Specific issue of individual documents referenced (see 2.2).

j. Inspection conditions

k. Conformance inspection and acceptable quality limits

6.3 First article. When first article inspection (see 3.1) is required, the contracting officer should provide specific guidance to offerors whether the item(s) should be first article sample, a first production item, or a standard production item from the contractor’s current inventory, and the number of items to be tested as specified in 4.2. Invitations for bids should provide that the Government reserves the right to waive the requirement for samples for first article inspection to those bidders offering a product which has been previously acquired or tested by the Government and that bidders offering such products, who wish to rely on such production or tests, must furnish evidence with the bid that prior Government approval is presently appropriate for pending contract.

6.4 Information requests. For access to information such as purchase descriptions, patterns, drawings, standard shade samples of cloth and/or Navy buttons, etc. go to DLA Troop Support’s Clothing and Textile website for their Specification/Pattern/Drawing Request form, https://www.dla.mil/troopsupport/clothingandtextiles/specrequest.aspx. Complete the request form and then submit form. Requests to use equivalent materials and/or components or to make changes to the pattern should be sent to the contracting officer for approval by the military services.

6.5 Shelf life. This specification covers items where the assignment of a Federal shelf-life code is a consideration. Specific shelf-life requirements should be specified in the contract or purchase order, and should include, as a minimum, shelf-life code, shelf-life package markings in accordance with MIL-STD-129 or FED-STD-123, preparation of a material quality storage standard for type II (extendible) shelf-life items, and a minimum of 85 percent shelf-life remaining at time of receipt by the Government. These and other requirements, if necessary, are in DoD 4120.27-M, Shelf-Life Management Manual. The shelf-life codes are in the Federal Logistics Information System Total Item Record. Additive information for shelf-life management may be obtained from DoD 4120.27-M, or the designated shelf-life Points of Contact (POC). The POC should be contacted in the following order: (1) the Inventory Control Points that manage the item and (2) the DoD Service and Agency administrators for the DoD Shelf-Life Program. Appropriate POCs for the DoD Shelf-Life Program can be contacted through the DoD Shelf-Life Management website https://www.shelflife.dla.mil/.

Preparing Activity Navy-SH

Custodian:

Navy-SH

DLA-CT

Review Activity:

Nav y- NU https://www.dla.mil/troopsupport/clothingandtextiles/specrequest.aspx https://www.shelflife.dla.mil/

Figure 1 – Gloves, Chemical and Oil Protective

Figure 2 – Porosity test apparatus