SATPC0039980 Tab 04 Drawing (FLL-HPROJ-0045).pdf

7 6 5 4 3

B B

C C

7 6 5 4 2

2 1

A

8 3

D

A

D

NOTES - UNLESS OTHERWISE SPECIFIED:

REVISION HISTORY

CHECKENGRDATEDESCRIPTIONREV

2025-06-23APPROVED FOR INITIAL RELEASE -

SHEET 1 OF 3CI NO. SCALE: NONE

-FLL-HPROJ-00451JYR2D

REV.DWG. NO.CAGESIZE

DIAGONAL SUPPORT MEMBER

TITLE

NATIONAL AERONAUTICS AND SPACE ADMINISTRATION

ARMSTRONG FLIGHT RESEARCH CENTER

EDWARDS, CALIFORNIA

2025-05-23M.R. SALAZARENGR

2025-05-23C. MASELLACHECK

2025-05-23A. HOLGUINREVIEW

2025-05-23L. HUDSONREVIEW

2025-05-21M.R. SALAZARDRAWN

2025-02-20M.R. SALAZARDESIGN

DATEAPPROVALS

THIRD ANGLE PROJECTION

DO NOT SCALE DRAWING

DECIMALS

.X .1

.XX .03

.XXX .010

.XXXX .0010

ANGLES

.X 0.5

.XX 0.25

UNLESS OTHERWISE SPECIFIED DIMENSIONS

ARE IN INCHES. TOLERANCES ARE:

PARTS SHALL BE FREE OF

BURRS AND SHARP EDGES

INTERPRET DRAWING PER

ASME Y14.100

USED ONNEXT ASSEMBLY

FLLFLL-HPROJ-0032

PARTS LIST

NOTES

MATERIAL

SPECIFICATION

NOMENCLATURE

OR DESCRIPTION

PART OR

IDENTIFYING NO.

CAGE CODE

ITEM

NO.QTY REQD

-101

W8X35 A36 STEEL I-BEAM

PER ASTM A36/A36MDIAGONAL, I-BEAM-00111

DIAGONAL END PLATEFLL-HPROJ-0037-10922

1. STOCK RADII ACCEPTABLE

2. WELD PER AMERICAN WELDING SOCIETY SPECIFICATION AWS

D1.1/D1.1M USING MIG WITH ER70S-3.

FOLLOW THE VISUAL INSPECTION ACCEPTANCE CRITERIA FOR

STATICALLY LOADED NONTUBULAR CONNECTIONS. PERFORM MAG

PARTICLE AND DYE PENETRANT NDT.

3 PRIMER/TOP COAT FINISH PER MIL-DTL-18264 AS FOLLOWS:

A. ONE COAT MIL-PRF-23377 EPOXY PRIMER, TYPE I, CLASS

<C1, C2, or N>

B. TWO COATS MIL-PRF-85285 POLYURETHANE, TYPE II,

COLOR 15092 (OSHA SAFETY BLUE) PER

SOCIETY OF AUTOMOTIVE ENGINEERS (SAE)

SPECIFICATION AMS-STD-595

4 APPLY HUMAN-READABLE IDENTIFICATION MARKING PER MIL-

STD-130 BY HANDWRITTEN PERMANENT INK. USE 0.5 INCH

CHARACTER HEIGHT. LOCATE APPROXIMATELY AS SHOWN.

MARKING SHALL READ AS FOLLOWS:

"1JYR2-FLL-HPROJ-0045-101" AND LATEST REVISION

-101 DIAGONAL SUPPORT MEMBER

ISOMETRIC VIEW

MAY INCLUDE EXPORT CONTROL

This document may include information that is subject to export control. It may not be transferred to foreign persons in the U.S. or abroad without specific approval of a knowledgeable export control official, and/or unless an export license, license exemption, or license exception is obtained/available from the Directorate of Defense Trade Controls, United States Department of State or Bureau of Industry and

Security, United States Department of Commerce. Violations of these regulations are punishable by fine, imprisonment, or both.

CONTROLLED BY: M.R. SALAZAR, AFRC, NASA

CUI//SP-EXPT

REVIEWED FOR CUI BY: M.R. SALAZAR, AFRC, NASA

(EXCEPT FOR EXPORT CONTROL)

NOT EXPORT CONTROLLED

THIS DOCUMENT HAS BEEN REVIEWED BY

THE AFRC EXPORT CONTROL OFFICE

AND IS DETERMINED TO BE

"NOT SUBJECT TO EXPORT CONTROL"

The information contained in this document is technical in content, but not technical data as defined by the International Traffic in Arms Regulations (ITAR) or the

Export Administration Regulations (EAR), and therefore is designated as EAR99/NLR, (No License Required). General Prohibition Six (Embargo) applies to all items subject to the EAR, (i.e. item on the CCL and within EAR99/NLR). You may not make an export or re-export contrary to the provisions of part 746 (Embargoes and Other Special Controls) of the EAR and 22 CFR §126.1 of the ITAR.

EAR99/NLR NOTICE

Carla Masella Full Size

C

D

7 6 5 4 3

A

A

D

C

SHEET 2 OF 3CI NO. SCALE: NONE

-FLL-HPROJ-00451JYR2D

REV.DWG. NO.CAGESIZE-101 DIAGONAL SUPPORT MEMBER

WELDMENTS

-101 DIAGONAL SUPPORT MEMBER

EXPLODED ISOMETRIC VIEW

CUI//SP-EXPT

N.S. F.S. N.S. F.S.

N.S. F.S. N.S. F.S.

SECTION A-A

2 PLACES

PARTIAL VIEW

3.5 3.5

0.50 0.50

8.00.50

8.00.50 3.5 3.5

0.50 0.50

3.5 3.5

0.50 0.50

3.5 3.5

0.50 0.50

8.00.50

8.00.50

9.0 9.0

0.25 0.25

C

D

7 6 5 4 3

A

A

D

C (.50)(8.02)

(8.13)

(.31)

(R.39)

2X 45.0

44.00

27.758.13

SHEET 3 OF 3CI NO. SCALE: 0.375

-FLL-HPROJ-00451JYR2D

REV.DWG. NO.CAGESIZE-001 DIAGONAL, I-BEAM, DETAIL

CUI//SP-EXPT