SATPC0033871 Tab 04 4 SOW.pdf

Orion Crew Survival System (OCSS) Suit Urine Tank Top and Bottom Shells

Rev. N/A October 03, 2023

STATEMENT OF WORK

ORION CREW SURVIVAL SYSTEM (OCSS)

SUIT URINE TANK TOP AND BOTTOM

SHELLS

Contracting Officer’s Representative Cinda Chullen

NASA Lyndon B. Johnson Space Center (JSC) cinda.chullen-1@nasa.gov

281-483-8384

TABLE OF CONTENTS

PARAGRAPH PAGE

1.0 GENERAL

1.1 Purpose

1.2 Background

1.3 Scope of Effort

2.0 REFERENCE AND APPLICABLE DOCUMENTS

2.1 Applicable Documents

2.2 Reference Documents

3.0 TASK DESCRIPTION

3.1 Urine Tank Unit

3.2 Urine Tank Unit Documentation

3.3 Status Review

3.4 NASA Input Requirements

4.0 DELIVERABLES

Appendix A ……………………………………………………………………………. 9 Appendix B…………………………………………………………………………….11

1.0 GENERAL

1.1 Purpose

This statement of work (SOW) specifies the requirement for fabrication and delivery of the hardware needed to assemble the NASA Orion Crew Survival Systems’ (OCSS) Suit Urine Tank flight unit. The Suit Urine Tank is component of the Off-Nominal Waste Management (ONWM) System of the OCSS.

1.2 Background

The purpose of the OCSS Government Furnished Equipment (GFE) project is supply the critical hardware to protect the crew in off nominal or contingency situations experienced during the mission that are life-threatening. The flight hardware is estimated to be delivered to Orion for the Artemis-2 mission slated to launch in late 2024. The ONWM System is being developed as part of the OCSS GFE project for use during the Orion Artemis missions. During an off-nominal, cabin depressurization event, the crew could be required to stay inside their OCSS suit for up to 144 hours until they return to Earth. In order to remain safely inside for a long duration, an internal-suit waste management system is needed to handle human metabolic waste. The Suit Urine Tank is a component of the ONWM System and flight units are specifically needed for the Artemis-2 mission.

1.3 Scope of Effort

The Contractor shall provide the Suit Urine Tank Bottom and Top Shells required to complete the effort defined in this SOW. This effort shall include the work described in Sections 2, 3, and 4 of this SOW.

2.0 REFERENCE AND APPLICABLE DOCUMENTS

The work performed shall conform to the requirements defined in this SOW and in the applicable documents listed below. Reference documents are listed below to assist in performing the scope.

2.1 Applicable Documents

SDH13103505 Suit Urine Tank Top Shell SDH13103507 Suit Urine Tank Bottom Shell JPR 8500.4 Engineering Drawing System Manual JPR 5322.1 Contamination Control Requirements Manual PRC-9002 Part Marking

2.2 Reference Documents

N/A

3.0 TASK DESCRIPTION

The following section provides a description of the scope of work for the Suit Urine Tank Top and Bottom Shells. A Contracting Officer’s Representative (COR) is assigned by the Contracting Officer to be the technical point of contract for this SOW.

3.1 Urine Tank Unit

The contractor shall fabricate and deliver the following parts:

3.1.1 The contractor shall fabricate and deliver one Urine Tank Top Shell to meet drawing specification # SDH13103505 as described in Section 2.1 of this SOW and included in Appendix A.

3.1.2 The contractor shall fabricate and deliver one Urine Tank Bottom Shell to meet drawing Specification # SDH13103507 as described in Section 2.1 of this SOW and included in Appendix B.

3.2 Urine Tank Unit Documentation

The contractor shall provide documentation to verify the quality of hardware fabricated and delivered. The contractor shall deliver the following documentation:

3.2.1 The contractor shall deliver a Certificate of Conformance for each hardware item delivered in Section 4 of this SOW.

3.2.2 The contractor shall deliver a Materials Test Report: Resin Specification (listing Lexan HP6NR-1H1111 as resin used).

3.2.3 The contractor shall prepare and deliver a Material Inspection and Receiving Report (DD Form 250). The form shall be prepared and delivered to the COR. The DD Form 250 shall be prepared in accordance with NASA FAR Supplement 1846.6 and in conjunction with guidance from the COR. The Contractor shall enclose a copy of the DD Form 250 with the hardware package or seal a copy of the DD Form 250 in a waterproof envelope, which shall be securely attached to the exterior of the hardware package in the most protected location.

3.3 Status Review

The contractor shall provide a monthly status review to inform NASA on progress of the fabrication. This review shall be presented in the form of PowerPoint equivalent presentation in an online meeting format. The information shall include progress on the hardware fabrication and delivery schedule.

3.4 NASA Input Requirements

The following items are NASA inputs to the contractor:

3.4.1 A separate pdf copy of the drawing specification # SDH13103505 will be provided at Authority to Proceed (ATP), and a .stp file can be provided upon request.

3.4.2 A separate pdf copy of the drawing specification # SDH13103507 will be provided at Authority to Proceed (ATP), and a .stp file can be provided upon request.

4.0 DELIVERABLES

The contractor shall deliver data and hardware as described below:

No. Title Comments Quantity Due

1 Monthly Status Review

A monthly status review shall be held to inform NASA on progress of the fabrication.

This review shall be presented in the form of PowerPoint equivalent presentation in an online meeting format. The information shall include progress on the hardware fabrication and delivery schedule.

1 per month

Date of review as agreed to by

NASA

2 Urine Tank Top Shell #1

This is the hardware that meets the drawing #

SDH13103505.

1 4 Months after Authority to Proceed (ATP)

3 Certificate of Conformance

For Urine Tank Flight Top Shell #1

1 Delivered with Urine Tank Flight Unit #1 Top

4 Urine Tank Bottom Shell #1

This is the hardware that meets the drawing #

SDH13103507.

1 4 Months after

ATP

5 Certificate of Conformance

For Urine Tank Bottom Shell #1

1 Delivered with Urine Tank Flight Unit #1 Bottom

6 Materials Test Report

Resin Specification (listing Lexan HP6NR-1H1111 as resin used)

1 With delivery of Deliverable Item #2 and #4

7 DD Form 250 Material Inspection and Receiving Report

1 With delivery of Deliverable Item #2 and #4

Appendix A

Appendix B