STATEMENT OF WORK (002).pdf
PDF 164 KB Posted
- Solicitation number
- 80MSFC27Q0005
About this file
This is a Statement of Work for the acquisition of an electrically heated batch walk-in series oven for NASA Marshall Space Flight Center (MSFC).
The requirement specifies a Wisconsin Oven brand or equivalent Model Batch-8/16/8-E10/RM with an 8'0" wide x 16'0" long x 8'0" high chamber capable of operating between 225°F above ambient and 1,000°F maximum, with temperature uniformity of ±15°F at 900°F. The oven features CAN-style construction with 2" ceramic blanket insulation and 4" industrial board insulation, a 6" reinforced integral insulated floor, bi-parting side-hinged doors with FM-approved safety latches, and a rotating mechanism with adjustable lathe chuck providing 2-10 revolutions per minute. Major components include a 25,000 CFM recirculation blower system at 25 HP, 1,500 CFM exhaust system at 1 HP, 408 kW heating equipment with zero-fired SCR power control, a Watlow F4T programmable controller with up to 40 recipes and 4.3" color touch screen, ten-position Type-K thermocouple jack panel, eight interior vacuum stubs with transducers, and two interior lights. The system requires 480 volt, 3 phase, 60 hertz power at approximately 540 full load amps and shall be painted Federal Safety Blue (oven body), gray (control panel), and OSHA yellow (guards). Equipment testing prior to shipment includes a systematic 150-point checklist evaluation and temperature uniformity survey.
Add-ons include a manual load car (6'0" x 12'0", 4,500-pound capacity), adjustable lathe chuck, estimated freight to Huntsville, Alabama, and turnkey installation/startup/training services consisting of five consecutive 9-10 hour days performed by two non-union technicians with all living and travel expenses included. The system shall be shipped completely assembled with the mandril drive removed, deliver within 35-40 weeks after receipt of order and down payment, and includes a three-year warranty covering all materials and specified components. Delivery shall proceed through NASA's Central Receiving Station (Building 4631) before final placement in MSFC Building 4707. The Point of Contact is Allison Clark at allison.m.clark@nasa.gov.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Combined Synopsis_Solicitation.pdf | ||
| Solicitation_80MSFC27Q0005_01_19 Nov 2026.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
STATEMENT OF WORK
Objective/Requirements
This requirement is for the acquisition of a Brand Name or Equal to Wisconsin Oven Electrically Heated Batch Walk-In Series Oven, a Model Batch-8/16/8-E10/RM, install and training NASA Marshall Space Flight Center (MSFC).
Characteristics, Scope, and Specs
The vendor shall provide a system that consists of the following Wisconsin brand name or equal major elements:
• Temperature Rating
• Maximum - 1,000 F Normal – 500 F – 900 F
• Minimum – 225 F above ambient
• Temperature Uniformity
• ±15 F at 900 F
• Documentation of the temperature uniformity testing and final adjustments to obtain the tolerance shown above are included as part of this proposal; the temperature survey will be a standard fifteen (15) point profile test conducted in an empty oven chamber under static operating conditions.
• Chamber Dimensions
• 8'0" wide x 16'0" long x 8'0" high
• Overall total dimension approximately 12'6" wide x 20'0" long x 15'0" high
• Construction
• Walls and ceiling feature “CAN” style construction and includes 2" of ceramic blanket insulation (2,300F service rating), backed with 4" of 6# density, industrial board type insulation (1,200F service rating), for a total of 6"; outer shell fabricated of 3/16" carbon steel plate, reinforced as required with structural steel; oven inner shell and ductwork fabricated of 18 gauge aluminized steel.
• Doors
• Bi-parting, side-hinged, horizontal swing doors at one (1) end; heavy gauge exterior with integral welded structural frame; ball-bearing hinges; FM approved safety latches; window in the right door; door limit switch, shuts the elements off when doors begin to open; blowers remain on.
• Oven Floor:
• Reinforced integral insulated floor (6" thick); carbon steel construction;
3/16" thick top plate; 12 ga bottom sheet; internal structural steel “egg crate” design for reduced heat transfer; 1" bar grating for load distribution;
designed for use with fork truck.
• Recirculation
• 25,000 CFM @ 25 HP; motor complies with NEMA Premium Efficiency
Standards; plug-mounted blower with soft start, V-belt drive & durable guards;
roof mounted to save valuable floor space; combination airflow through the work chamber, with the majority of air supplied under the work, to flow vertically upward past and through the product; airflow safety switch (proof-of-operation).
• Exhaust:
• 1,500 CFM @ 1 HP; motor complies with NEMA Premium Efficiency Standards;
motor operated dampers (exhaust & fresh air) for enhanced cooling (where the dampers open at the end of the heat cycle); oven rated for Class A use where flammable volatiles or powder coatings are processed; rated for 0.5 gallons of solvent per batch at the normal operating temperature; airflow safety switch (proof-of-operation);
• Heating Equipment:
• 408 kW heat input at the voltage indicated below under “Utility Requirements”;
zero-fired SCR power control with back-up contactors; heaters wired individually so if one fails
• Controls and Instruments:
• Located in a UL (508A Type 1) certified and labeled NEMA 12 enclosure mounted on the right side of the oven with the instruments and controls mounted on the cabinet door, including the following major components
• Watlow F4T paperless digital recorder/programmable controller to provide temperature control and record the oven control thermocouple; up to 40 recipes;
4.3" color touch screen; graphical trending; USB port for downloading data;
Ethernet (Modbus® TCP) USB communication capabilities; PID temperature control with adaptive tuning.
• Digital oven high limit instrument, FM approved, with manual reset
• IEC style motor starters, push buttons and pilot lights (to indicate status), fused branch circuits, 110 volt control transformer and blower interlocks
• Main power disconnect switch with interlock to help prevent unauthorized personnel from opening control panel door when the disconnect switch is “ON”
• electrical components designed for factory ambient temperature of 60 F to 105 F
• EMT conduit on the equipment
• Oven Lighting:
• Two (2) lights to illuminate interior, switch on control panel
• Rotating Mechanism:
• One (1) adjustable lathe chuck with a 3" opening rotating mechanism mounted at rear of oven to provide a mandrel rotation of 2 to 10 revolutions per minute;
mandrel drive shaft will be supplied with a rotary thrust device and (female slotted disc) through a hole in the back of the oven; AC rotational Drive, and rotation monitor (an alarm will sound if the drive shaft should cease to rotate)
• Vacuum Piping Components:
• Eight (8) interior vacuum stubs total; four (4) active (each a 1/2" NPT BI pipe w/ male threaded end on the interior and a shut-off cock on the exterior); the stubs will be piped to a main vacuum manifold (1- ¼" NPT BI pipe w/ male ends), four
(4) passive each with one (1) vacuum transducer will be provided on each vacuum line, the sensors will be mounted downstream of each vacuum inlet pipe;
interconnecting wiring between the junction box and the monitoring system is not included.
• TC Jack Panel:
• Ten (10) position type “K” thermocouple (TC) jack panel mounted approximately 60" above the shop floor, with ten (10) male connectors; customer will run TC wires into the interior of the oven through a TC port and plug the male jack(s) into the jack panel, which will be wired to the panel-mounted recorder/data acquisition
• Insurance and Other Requirements:
• NEC, NFPA 79 & 86 recommended equipment
• Electrical - 480 volt, 3 phase, 60 hertz; approximately 540 full load amps
• Paint: The equipment will be painted the following colors:
• Oven body - heat resistant Federal Safety Blue urethane exterior (the aluminized steel interior requires no additional coating)
• Control panel - gray exterior
• Guards - OSHA yellow
• Piping and Conduit - Unpainted
• Testing:
• Equipment is operated at normal and maximum temperatures prior to shipment;
all safety interlocks are checked for proper operation; includes a systematic evaluation utilizing a check list with over 150 points (actual number varies depending on the type of equipment); temperature uniformity survey.
• Manual: One (1) digital Owner’s Manual in English
• Completion:
• The equipment will be ready for shipment and/or inspection thirty-five to forty (40) weeks after receipt of an order and down payment
• Shipping
• Shipped completely assembled with the mandril drive removed
• 3-Year Warranty
• Covers all materials for all components (less wear items); components covered include, but are not limited to: recirculation, exhaust, & combustion blowers;
burner, burner controls, & all gas train components; temperature controllers, high-limit instruments, & recorders; disconnect switches; power distribution blocks;
terminal blocks; transformers; fuse blocks; selector switches & push buttons; pilot & beacon light assemblies; process & purge timers; SSR & SCR’s; contactors;
relays; alarm horns; pressure switches; limit switches; vent fans; power supplies;
variable frequency drives; etc. as applicable to the equipment quoted
Add Ons
• Load Car: One (1) manual load car; 6'0" wide x 12'0" long will be provided; two fixed and two (2) adjustable roller supports in one (1) row of two (2) to accept your 25" diameter mandrel shaft; maximum length of the mandrel is 12'6" long, with total weight capacity of 4,500 pounds; includes an adjustable lathe chuck with a 3" opening in lieu of the rotary thrust device; load car will be supplied with casters (2 swivel and 2 rigid), as well as a removable drip pan under the mandrel and a removable handle on one (1) end
• Adjustable lathe chuck with a 3" opening in lieu of the rotary thrust device included above
• Estimated freight cost to your Huntsville, AL facility via Direct freight, not including weekend or holiday deliveries;
• Turnkey Installation, Startup and Training: Five consecutive 9-10 hour days (excluding Sundays) of installation, start-up and training at Huntsville, AL facility, performed by two (2) non-union Oven technicians
• Oven off-loaded from the truck(s) and placed into position at the jobsite
• Installation of oven sections and all ship-loose items such as recirculation blowers, exhaust fan, etc.
• Lagging oven to the foundation
• Final utility connections
• Start up equipment and verify operation in accordance with the
Oven proposal
• Training of customer personnel
• All living and travel expenses for Oven technicians
QTY BRAND NAME OR EQUAL DESCRIPTION
1 Electrically Heated Batch Walk-In Series Oven 1 Load Car (Price Adders) 1 Adjustable lathe chuck with a 3" opening (Price Adders) 1 Shipping (Price Adders) 1 Turnkey Installation, Startup and Training services (Price Adders)
Delivery
• The thermoplastic oven system shall be packaged/crated and shipped to NASA via shipping and installation add on descriptions
• The entire system and all components thereof shall be fully insured and indemnified against loss, damage, theft, or any other circumstance that causes a failure to deliver the system in its full working capacity once installed.
• The system shall be delivered to NASA’s Central Receiving Station at NASA/Marshall Space Flight Center, Central Receiving Facility Building 4631, MSFC, AL 35812 for initial property documentation and processing.
• The system shall remain onboard the shipping vehicle during this process.
• Upon completion of property receipt documentation and processing, the shipping vehicle shall deliver the system to MSFC Building 4707, Apollo Road, MSFC, AL 35812 and offloaded by into the large room adjacent to the large autoclave
Place of Performance
NASA Marshall Space Flight Center (MSFC)
ATTN: MSFC/EM42
Building 4707 Huntsville, AL 35812 POC: Allison Clark (allison.m.clark@nasa.gov)
Period of Performance
35-40 weeks After Receipt of Order
File details come from the government source that posted it. Updated .