77475 - Drawing - Rubidium.pdf

APPLICATION REVISIONS

NEXT ASSY USED ON LTR DESCRIPTION DATE APPROVED

201323401-10 ARTS - INITIAL RELEASE DATE

ALL SHEETS REV___-__ VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT D. Distribution authorized to the Department of Defense and U.S. DoD contractors only (Critical Technology) (22 December 2006). Other requests shall be referred to 565 CBSS/GBLB.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.). or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25.

DESTRUCTION NOTICE. Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ARE

DECIMALS ANGLES APPROVALS DATE

U.S. AIR FORCE

WR-ALC, ROBINS AFB, GA 31098

XX± ± DRAFTSMAN

ADAM FRANK

TITLE

.XXX ± CHECKER

RUBIDIUM STANDARD

DO NOT SCALE DRAWING MATERIAL ENGINEER

THIRD ANGLE

PROJECTION

PROJECT ENGINEER

PROJECT AUTHORITY

WES JAMES BENNETT

SIZE

A

CAGE CODE

98752

DRAWING NO.

201995762

REV

RELEASE AUTHORITY

HAROLD BANKS

SCALE

NONE

CAL.WT ACT.WT SHEET

Exception to AF 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word 2003) 201995762.DOC Computer Generated

CAGE: 98752 DWG. NO.: 201995762 REV - SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 20199576220.DOC Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

ASME Y14.38, ABBREVIATIONS AND ACRONYMS.

MIL-STD-130M IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

2. THIS DRAWING ESTABLISHES THE REQUIREMENTS FOR A COMMERCIAL OFF THE SHELF

RUBIDIUM STANDARD.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE

OF SUPPLY FOR THE ITEM(S).

4. QUALITY ASSURANCE. THE SUPPLIER SHALL VERIFY THAT UNITS SUPPLIED TO THIS

DRAWING CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN.

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

WHICH WOULD AFFECT INTERCHANGEABILITY OR DEGRADE EITHER PERFORMANCE OR

RELIABILITY OF THE PRODUCT WITHOUT PRIOR NOTICE

6. CONFIGURATION ITEM: DO NOT CHANGE WITHOUT SYSTEM ENGINEER APPROVAL.

CONFIGURATION:

FRONT VIEW

REAR VIEW

CAGE: 98752 DWG. NO.: 201995762 REV - SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 20199576220.DOC Computer Generated

ELECTRICAL SPECIFICATIONS Low Noise (option)

FREQUENCY 10MHz FORMAT Sine Wave AMPLITUDE 1Vrms DISTORTION <33dBc

CONNECTOR BNC

LOAD IMPEDANCE 50Ω

NUMBER OF OUTPUTS 6

PERFORMANCE PARAMETERS

STABILITY:

0 TO 50°C

±1.0E-10

AGING:

MONTHLY

<5E-11

PHASE NOISE

OFFSET (Hz) 1,000 10,000

10MHz <-100dBc <-130dBc <-144dBc <-150dBc <-157dBc

ENVIRONMENTAL & PHYSICAL SPECIFICATIONS

GENERAL ENVIRONMENT (OPERATING)

TEMPERATURE 10°C TO 35°C

HUMIDITY 95% NON-CONDENSING

AC POWER REQUIREMENTS

115/230 VAC

DIMENSIONS/WEIGHT

1U 19” RACK MOUNT

<6 lbs.

CONTROL

NUMBER

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201995762-01 03NF8 015006011

1/

BRANDYWINE COMMNUNICATIONS

1153 WARNER AVE

TUSIN, CA 92780

201995762-01 1B0C5 15230-104 2/

MICROSEMI FREQUENCY & TIME CORP.

3870 N 1ST ST

SAN JOSE, CA 95134

1/ THE MODEL NUMBER IS QFS-106

2/ THE MODEL NUMBER IS 8040CLN

1290613201C Highlight