- Attached to
- NAVY NP FENDER RENEWAL
- Solicitation number
- 70Z04027Q60514Y00
- Issued by
- Not on record
About this file
This is a Statement of Work (SOW) for a Rubber Fender System procurement (YP 676 Class) under a U.S. Coast Guard solicitation for Navy NP Fender Renewal. The U.S. Coast Guard, Surface Forces Logistics Center (SFLC) is seeking quotes for rubber fender system components on a Firm Fixed Price basis through simplified acquisition procedures (FAR 13). Quotes must be received by November 16, 2026, at 9:00 AM Eastern Time and should be emailed to Erica.L.Gibbs@uscg.mil with the solicitation number 70Z04027Q60514Y00 in the subject line. Award will be made on a best value basis, with evaluation criteria focused on meeting all technical requirements, adherence to delivery deadlines, and price.
Payment terms are Net 30 via Government Purchase Order, with no advance or down payments permitted. The awarded vendor assumes financial responsibility for the order until acceptance and receipt by the U.S. Coast Guard, and payment of work is authorized upon completion subject to Contracting Officer approval. Past performance will be reviewed only for responsibility determination per FAR 9.1. This is a competitive procurement where all responsible sources are eligible to submit quotations for consideration.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| SOLICITATION ATTACHMENT- FAR CLAUSES.pdf | ||
| 6170183b HULL FITTINGS A-D.pdf |
On GovTribe
Work with this file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRAFT: YP 676 Class Item No: 611-11-001CUI
1. SCOPE:
1.1 Title: Rubber Fender System; replace (611-11-001)
1.2 Location of Work:
1.2.1 Exterior Hull from Bow to Stern, Port and Starboard, and Transom
1.3 Identification:
1.3.1 Quantity (24), Fender, 20 Foot Length, Type-D Shape, Black EPDM, 6-inch by 6-inch, identified as GFM in section 5
2. REFERENCES:
2.1 611-6170183 Rev B, 108' Yard Patrol Craft, Hull Fittings A/D
2.2 631-8629935 Rev F, 108’ Yard Patrol Craft, Paint Schedule
3. REQUIREMENTS:
Remove all upper and lower fendering located in 1.2 including securing bars and associated hardware, using 2.1 for guidance.
"JOINT VISUAL INSPECTION"
Accomplish a visual inspection of the 2-1/2 inch by 1/2-inch CRES fender securing flat bars after removals in 3.1 for structural integrity, deterioration, cracks and areas of damage or distortion.
Accomplish a visual inspection of the fender mounting plate shown in Detail "15-A" of 2.1 in the areas exposed by the removals in 3.1 for structural integrity, deterioration, cracks and areas of damage or distortion.
Accomplish a visual, probe and hammer test inspection of the oak shim in the areas exposed by the removals in 3.1 shown in Section Views "10-C", "16-D", "16-G" and Detail "16-E" of 2.1.
Report: Inspection Results Date: + 2 Submit one legible copy, in hard copy or approved transferrable media, of a report listing results of the requirements of 3.1.1, 3.1.2, and 3.1.3 to the SUPERVISOR, showing exact locations, quantities and conditions of deficiencies and recommendations for repairs.
Replace with new a total of 60 linear feet of damaged, bent or deteriorated 2-1/2 inch by 1/2 inch CRES fender securing flat bars, resulting from inspection of 3.1.1 as designated by the SUPERVISOR.
Remove and install a total of 75 linear feet of existing upper and lower fender mounting plate. Remove existing and install new a total of 75 linear feet of upper and lower fender mounting oak shim, resulting from inspection of 3.1.2 and 3.1.3 as designated by the SUPERVISOR.
Template exact size and shape of oak shim from existing craft conditions. Scarf configuration shall be similar to Detail 16-A of 2.1 using West System epoxy as glue.
Replace all existing studs with new. New studs shall conform to the material requirements of Part No. 22 of 2.1. New studs shall be 5/8-11 x 4 inches long vice 5/8-11 x 3 inches long shown on 2.1. Chip and grind surfaces flush and smooth in way of removals.
Install new nuts, in accordance with the material requirements of Part No. 21 of 2.1.
Install new washers, in accordance with the material requirements of Part No. 20 of 2.1.
Accomplish the requirements of 2.2 for surface preparation and preservation of the upper and lower fender mounting oak shim. Note that taking down to bare wood is not required if surface coating condition is sound.
Upon completion of 3.2, install new upper and lower hull, and upper and lower transom rubber fenders.
4. NOTES:
4.1 None.
5. GOVERNMENT FURNISHED MATERIAL (GFM - furnished by customer):
5.1 Quantity (24), Fender, 20 Foot Length, Type-D Shape, Black EPDM, 6 inch by 6 inch (located at Coast Guard Yard, Curtis Bay, MD)
CUI
1 of 2 Item No: 611-11-001
File details come from the government source that posted it. Updated .