70Z03822QM0000016_Redacted_JA.pdf

JUSTIFICATION FOR OTHER THAN FULL AND OPEN COMPETITION

SIMPLIFIED ACQUISITION PROCEDURES (SAP) FAR 13.106-1(b)

SOLICITATIONS MAY BE LIMITED TO ONE SOURCE ONLY IF THE CONTRACTING OFFICER DETERMINES THAT ONLY ONE SOURCE IS REASONABLY AVAILABLE. THIS DETERMINATION MUST BE SUPPORTED WITH FULL JUSTIFICATION FOR SOLE SOURCE FROM THE CUSTOMER. WHEN THE CUSTOMER DESCRIBES AN ITEM WITH A PURCHASE DESCRIPTION WHICH LIMITS THE AVAILABILITY TO ONE SOURCE, THE JUSTIFICATION MUST EXPLAIN WHY THE ITEM IS THE ONLY ONE THAT WILL MEET THE GOVERNMENT’S REQUIREMENT. STATEMENTS SUCH AS "ONLY KNOWN SOURCE" OR "ONLY SOURCE WHICH CAN MEET THE REQUIRED DELIVERY DATE" ARE INADEQUATE TO

SUPPORT A SOLE SOURCE PURCHASE.

PURCHASE REQUEST OR REQUISITION

NUMBER

PROJECT/TASK

ESTIMATED AMOUNT (Over Micro- Purchase Threshold, but up to the SAT)

IDENTIFICATION OF THE AGENCY AND THE CONTRACTING OFFICE, AND SPECIFIC IDENTIFICATION OF THE DOCUMENT AS A “JUSTIFICATION FOR OTHER THAN FULL AND OPEN COMPETITION.” PLEASE CITE THE

AUTHORITY AND TYPE OF JUSTIFICATION.

The United States Coast Guard (USCG), Aviation Logistics Center (ALC), Information Systems Division (ISD) anticipates the award of a purchase order on a sole source basis. This justification for other than full and open competition is submitted for approval in accordance with (IAW) Federal Acquisition Regulation (FAR) 6.303-1 (a) using the authority in FAR 6.302-l(b)(2)- only one responsible source and no other supplies or services will satisfy agency requirements.

BRIEF DESCRIPTION OF SUPPLIES OR SERVICES REQUIRED, AND THE INTENDED USE.

MasterCam Software Support Renewal from 01 Sep 2022 through 31 Aug 2023 SIM #'S 172179, 124190, 82518, 186722, and 186723. P/Ns: N/A NSN: N/A Qty: 1

UNIQUE CHARACTERISTICS THAT LIMIT AVAILABILITY TO ONLY ONE SOURCE, WITH THE REASON NO OTHER

SUPPLIES OR SERVICES CAN BE USED.

Barefoot CNC is the authorized reseller of Mastercam software and software subscription renewals for North and South Carolina.

The USCG utilizes this software to design, mill, and lathe aircraft parts. It would be cost prohibitive to restructure the current system.

A DESCRIPTION OF EFFORTS MADE TO ENSURE THAT QUOTATIONS OR OFFERS ARE SOLICITED FROM AS MANY

POTENTIAL SOURCES AS PRACTICABLE (INCLUDE YOUR MARKET RESEARCH EFFORTS HERE).

Extensive market research was conducted using both Government and commercial sources. This included querying the following information systems and web sites: Defense Logistics Agency (DLA) Federal Logistics Information Service (WebFLIS);

Department of Defense Electronic Mall (DoD EMall); the General Services Administration's (GSA) on-line purchasing service- GSA Advantage!®; Inventory Locator Service e-marketplace (ILSmart); internet search engines; and the OEM's web site. These services are not available from any mandatory Government source IAW FAR 8.002 or from any non-mandatory source IAW

FAR 8.004.

REASON THAT SUGGESTED SOURCE IS THE ONLY SOURCE WHICH CAN PROVIDE THE SUPPLIES OR SERVICES.

Barefoot CNC is the only authorized reseller of Mastercam software and software subscription renewals for North and South Carolina. As such, Barefoot CNC holds all proprietary rights to the system's design and data and do not license its use to any other companies.

EXPLAIN WHY AN ADEQUATE PURCHASE DESCRIPTION OR OTHER INFORMATION SUITABLE TO SOLICIT BY FULL

AND OPEN COMPETITION HAS NOT BEEN DEVELOPED OR ARE NOT AVAILABLE.

The Government does not own or possess any rights to the software code required to make any changes to the Barefoot CNC MasterCam Software. The development of the code required for the USCG to create a comparable information system has been deemed uneconomical. In addition, it would be difficult to integrate historical measurements and other data into any new software so that long-term performance can be reported and analyzed.

PROVIDE A STATEMENT OF ACTIONS, IF ANY, THE GOVERNMENT MAY TAKE TO REMOVE OR OVERCOME ANY

BARRIERS TO COMPETITION BEFORE FUTURE ACQUISITIONS ARE REQUIRED.

As previously stated, the Government does not own or possess any rights to the software source code that is required in order modify the Barefoot CNC MasterCam Software. This has prevented the USCG from being able to provide an adequate technical description to potential new sources. It is difficult to take steps to foster competition when the necessary data is proprietary to the OEM.

SIGNATURE AND TITLE OF CUSTOMER

CODE TELEPHONE

DATE5

SIGNATURE OF CONTRACTING OFFICER

CODE DATE

August 2020