7-RFP-02-Scope of Services Auto Body Shop Repairs 27-0024.pdf

PDF 261 KB Posted

Attached to
RFP Auto Body Shop Repairs
Solicitation number
27-0024
Issued by
Tarrant County, Texas

About this file

This Scope of Services document is an RFP issued by the City of Fort Worth, Texas (Purchasing Division) for Auto Body Shop Repairs services to be provided to approximately 4,600 city-owned vehicles and equipment. The City seeks to establish agreements with multiple qualified vendors to provide collision maintenance and repair services for light, medium, and heavy-duty vehicles weighing over and under 1-ton Gross Vehicle Weight Rating. The initial contract term shall be four years, with up to two optional one-year renewal periods available under the same terms and conditions unless non-renewal notice is provided. Vendors must provide all labor, supervision, equipment, materials, transportation, and resources necessary to perform comprehensive repair services. The RFP requires vendors to maintain secure facilities with monitoring systems, possess industry-recognized certifications and equipment (including frame repair machines, paint booths, welding equipment, and alignment systems), and comply with all applicable local, state, and federal regulations and permits. All repair work must adhere to Original Equipment Manufacturer (OEM) specifications and industry standards established by I-CAR and ASE.

Pricing must be presented on a time-and-materials basis using hourly labor rates with paint and material costs not exceeding two-thirds of the hourly labor rate; environmental disposal fees are capped at $50.00 per invoice. The City has established a 30% Small Business participation goal for this solicitation, requiring at least 30% of the total awarded contract value to be subcontracted or spent with certified Small Business firms. Proposals will be evaluated on a "best value" basis across five criteria: Cost (up to 20 points), Staffing Levels (up to 20 points), Experience and Qualifications (up to 20 points), Methodology for providing services (up to 20 points), and Small Business participation (up to 20 points), with proposals scoring below 50% on non-price criteria deemed non-responsive. Vendors must respond to City correspondence within 48 hours, provide weekly repair status reports, maintain comprehensive warranties (five years for body/collision work and paint; minimum one year for mechanical/electrical), and allow up to three days for City inspection and approval before invoicing. The scope includes services at four designated fleet service center locations, with standard operating hours Monday through Friday, 7:30 a.m. to 4:30 p.m., and excludes work on City holidays without written approval.

View the file

Other files

File Type Posted
4-RFP-03-Draft Vendor Service Agreement.docx DOCX document
3-RFP-01-Instruction to Proposers.pdf PDF
5-RFP-07-Deviations.xlsx XLSX spreadsheet
1-RFP-05-Forms.pdf PDF
2-RFP-06-Small Business Utilization Form V1.docx DOCX document
6-RFP-04-Authorized Signature and Questionnaire ABSR.docx DOCX document

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

CITY OF FORT WORTH - PURCHASING DIVISION

SCOPE OF SERVICES

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 1 of 20 RFP Title: Auto Body Shop Repairs

1.0 INTRODUCTION AND PURPOSE

The City of Fort Worth (“City”) is requesting proposals from auto body shops to secure an agreement with multiple industry-proven, qualified vendors to provide Auto Body Collision Maintenance & Repair Services to approximately 4,600 City-owned vehicles and equipment weighing Over and Under 1- Ton Gross Vehicle Weight (GVW) located at facilities managed by the Property Management Department. These auto-body shops should cover collisions, repairs, and maintenance services for city vehicles.

The initial term of this contract shall be four (4) years. Upon the expiration of the initial term, the agreement shall renew under the same terms and conditions for up to two (2) one-year renewal periods, based on the same terms, conditions, and pricing unless City or Supplier provides the other party with notice of non-renewal.

The City reserves the right to award agreements to one or more qualified Vendors. Awarded Vendor(s) shall provide all labor, supervision, equipment, materials, transportation, and other resources necessary to perform the requested services. The successful respondent(s), hereafter referred to as “Proposer” or “Vendor,” shall provide all labor, supervision, equipment, materials, and transportation necessary to perform the requested services.

2.0 SCOPE OF SERVICES

2.1 Vendors must provide body work service and repairs to City-owned light, or medium, and heavy-duty vehicles and equipment.

2.2 Vendors agree to comply with all applicable codes and ordinances of the appropriate local, state and/or federal laws as they may apply, as these laws may now read or as they may hereafter be changed or amended.

2.3 Vendors must obtain from the appropriate local, state and/or federal agencies the necessary permit(s), if any, required by the ordinances

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 2 of 20 RFP Title: Auto Body Shop Repairs for the performance of the work.

2.4 Vendors must furnish for each facility that will perform services:

insurance, permits, licenses, labor, personnel, service, supervision, management, reports, documentation, material, supplies, tools, equipment, towing, surcharges, transportation, and all other cost associated with this contract necessary to provide the highest quality of vehicle auto body and collision repair services. All licenses, permits, insurance and any other documentation that is required by local, state and/or federal agencies are to be maintained during the term of this contract.

2.4.1 Vendors must price paint and material at an hourly rate and must not exceed two-thirds of cost of the Hourly Labor Rate - Paint Labor. Miscellaneous expenses must be factored into paint and material costs.

2.4.2 Environmental fees (oil, transmission fluid, anti-freeze, and tire disposal) must not exceed $50.00 per invoice, and any amount over $50.00 must require City approval.

2.5 Vendors must obtain City approval and authorization in writing to sublet any work. Vendors must submit a quote with the estimated costs of sublet work that must be performed. The city will pay for sublet items at Cost Plus (+) %, per the Vendors’ proposal submission.

2.6 Vendors must have a minimum of two (2) consecutive years in the light or medium, and heavy-duty equipment and vehicle body repair and service business industry.

2.7 Upon request, if Vendor personnel will access City of Fort Worth vehicles, facilities, secured work areas, digital systems, or any City-managed data, those personnel must be subject to a Criminal Background Check as required by applicable City departments.

Background Checks paid for by the vendor may include, but are not limited to, a Criminal Justice Information Services (CJIS) Background Check, a Human Resources Criminal Background

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 3 of 20

Check, or other screenings required by the city.

2.8 Location of Accident Vehicle

2.8.1 Vendors must not charge the City of Fort Worth for storage of vehicles.

2.9 Vehicle Security

2.9.1 Vendors’ facility must have an indoor or outdoor secure locked parking lot with a security monitoring system.

2.9.2 Vendors are responsible for the security of all City of Fort

Worth vehicles while in their possession.

2.9.3 City of Fort Worth reserves the right to assign an independent appraiser to give an estimate for damage that occurred to vehicle while in possession of Vendors. No work shall be authorized without a claim number for accidents involved vehicles. Additionally, a valid City Purchase Order is required before any work may be performed.”

2.10 Site Visits

2.10.1 The City of Fort Worth reserves the right to visit the Vendors’ facility at any time after an award has been made for facility and repair inspection on any City of Fort Worth vehicles.

2.10.2 Vendors must have their own operating facility to complete all body repair services, including air conditioning service and recharging, alignment, welding, lifting, painting, and related repair work.

2.10.3 Vendors must have industry recognized heavy equipment

“extended” sized paint booth systems to allow for proper painting applications for trucks/vehicles.

2.10.4 Vendors must have, on-site, a complete paint mixing system for matching color requirements. Paint products and painting

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 4 of 20 RFP Title: Auto Body Shop Repairs procedures must meet manufacturers’ Original Manufacturer Equipment (OEM) requirements for quality and warranty considerations. Unapproved and/or non-color matches vehicles will be repainted at the contractor’s expense, if found unsatisfactory by the City of Fort Worth.

3.0 PARTS

3.1 Vendors must follow the directions in the use of OEM, Certified

Automotive Parts Association aftermarket (CAPA certified), or recycled parts either from parts Vendors or City supplied for replacement or repair. For each repair, the Vendors(s) must provide an invoice listing OEM, CAPA certified aftermarket parts, recycled parts purchased or listed as received from the City of Fort Worth for the assigned vehicle.

3.2 Vendors must keep and provide a shown ability for acquiring recycled parts via part Vendors networks and contacts.

3.3 Vendors must keep all the old parts from the damaged vehicles until an inspection from the City of Fort Worth Property Management Department Fleet Division Assistant Director or assigned designee representative and/or City independent appraiser has been completed and satisfied. Once final inspection is complete, the parts can be disposed of properly by Vendors following all local, state, and federal regulations. The City always reserves the right to acquire any part removed from the vehicle being repaired. The ability to recycle is always recommended by the city as appropriate.

3.4 Vendor must provide a receipt of their cost with every invoice incurring freight. The city must approve in writing the products shipped incurring freight prior to the Vendor shipping the products all parts purchased for vehicles under and over 1 ton.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 5 of 20 RFP Title: Auto Body Shop Repairs

4.0 QUALIFICATIONS

4.1 Vendors’ employees who work on City-owned vehicles shall possess a certification from Inter-Industry Conference on Automotive Collision Repair (I-CAR) or other manufacturers certifications, be skilled and knowledgeable of all phases of light or medium and heavy-duty body repair and restoration services.

4.2 Vendors must inspect all repairs to ensure they meet or exceed industry standards as defined by I-CAR, Automotive Service Excellence (ASE), and OEM recommended repair methods. Subcontractors must follow the same guidelines as specified in this proposal.

4.3 Technicians

4.3.1 Prospective Vendors must provide qualifications for each staff by role (structural, non-structural, refinish, electrical/mechanical) proposed to work under this contract.

These qualifications may include I-CAR, ASE, OEM, and/or other certifications/qualifications.

4.3.2 Vendors’ technicians of light or medium, and heavy-duty repair must have experience and knowledge in the inter working of diesel drivetrains.

4.3.3 Certification documentation for the technicians must be submitted with the proposal for review and evaluation criteria.

4.4 Frame System

4.4.1 Vendors must have an onsite anchoring industry recognized frame/structure multi post pulling post/frame repair machine.

Machines must have the ability for multiple angles pulls. Frame machines are required to produce printable before and after measurements to certify straightening, repair, or replacement items are returned to manufacturer specifications OEM and pre-accident conditions. Before and after measurement prints must

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 6 of 20 RFP Title: Auto Body Shop Repairs be provided with the final invoice.

4.5 Alignment Machines

4.5.1 Vendors must provide access to alignments either by in-shop industry recognized equipment, or acceptable use of a subcontract Vendors for alignment service. Before and after alignment specifications are required to be printed before and after the measurement. This is to verify the vehicle is back to pre-accident condition and meets manufacture specifications OEM. Copy of measurements are required to be sent with final invoice.

4.6 Air Conditioning Repair/Recharging Services

4.6.1 Vendors must have an air conditioning refrigerant recycling and charging system that meets all local, federal and state requirements.

4.7 Welding

4.7.1 Vendors must have appropriate welding equipment for body welding and utilize I-CAR or other industry standard certified welding procedures. Gas welding is not acceptable, no exceptions.

4.7.2 Vendors must have appropriate welding equipment to perform fabrication abilities on light or medium and heavy and heavy-duty equipment and vehicles.

4.7.3 Vendors must have appropriate equipment for aluminum welding.

4.7.4 Vendors must make sure the vehicle computer systems and airbag triggers are disconnected prior to any welding performed.

4.7.5 Vendors must be responsible for total replacement of the vehicles on-board computers and airbag components damaged

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 7 of 20 RFP Title: Auto Body Shop Repairs due to negligence, by not disconnecting appropriate systems required by the manufacturer and associated repair process before performing welding.

4.8 Vehicle Lifting System

4.8.1 Vendors must possess a fully functional industry standard equipment lifting system for damage inspections and repair purposes.

4.9 Headlight Aiming

4.9.1 Vendors must possess a fully functional headlight-aiming tool/ system. Common methods used include but are not limited to screens, electronic indicators, or float-type bubble system.

4.10 Paint Requirement

4.10.1 Vendors must have industry recognized heavy equipment

“extended” sized paint booth systems to allow for proper painting applications for trucks/vehicles.

4.10.2 Vendors must have on-site a complete paint mixing system for matching color requirements. Painting products and procedures must meet manufacturers’ OEM requirements for quality and warranty considerations.

4.11 Mechanical Requirement

4.11.1 Vendors must complete all mechanical services and repairs, including but not limited to: front and rear suspension, drive train components, air bags, anti-lock brakes, emission and other sensors, steering columns, lights, computer controls and associated wiring, engines, transmissions, final drives, extension slides, hydraulic components, steering motors, that require replacement as indicated on the original written estimate and/or supplement be completed by the awarded Vendors(s) or authorized subcontractor.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 8 of 20

4.11.2 Vendors must return all vehicles to pre-accident conditions and meet or exceed manufacturer specifications OEM.

4.12 Quality Control

4.12.1 All installations and fabrications will be subject to inspection by City of Fort Worth Property Management Department Fleet Division Assistant Director or assigned designee. All re-work must be performed at no additional cost to the city with the timeframe determined by the city.

4.13 Hidden Damage

4.13.1 During repairs, Vendors must contact the City of Fort Worth

Property Management Department Fleet Division Assistant Director or assigned designee and/or City’s independent appraiser for re-inspection and approval. If additional damages are found that were not included in the original estimate. No supplemental or hidden damage repairs may proceed without written City Approval.

4.14 Collision Repairs

4.14.1 Vendors must guarantee and demonstrate that all structural repairs performed meet or exceed manufacturer OEM and/or I-CAR repair specifications.

4.14.2 Vendors must utilize modern, well-maintained tools which meet manufacturer specified use or I-CAR specified use.

4.14.3 Vendors must be required to have all frame replacements approved in writing by PMD Superintendent and assigned PMD Fleet Assistant Director.

4.15 Glass Removal and Installation

4.15.1 Vendors must use OEM or I-CAR defined glass removal and

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 9 of 20 RFP Title: Auto Body Shop Repairs install procedures. Glass service is allowed by the repair facility or through subcontract glass Vendors. Glass urethanes shall meet or exceed manufacturer specifications.

Glass shall also meet or exceed OEM safety and integrity.

OEM or aftermarket glass which meets or exceeds OEM specifications will be acceptable.

4.16 Inspections and Approval Process

4.16.1 Vendors must allow the City of Fort Worth Property

Management Department, Fleet Division Assistant Director or designee up to three (3) days to inspect all vehicle services and repairs. The department representative or designee will sign off on all inspections that meet the City’s required standards.

4.17 Workmanship Standards

4.17.1 Repairs must be performed to industry-accepted professional standards, ensuring structural integrity, proper alignment, and high-quality finishing.

4.18 OEM Repair Procedures

4.18.1 All repairs must follow Original Equipment Manufacturer (OEM) guidelines, including use of approved parts, materials, and repair methods.

4.19 Safety Standards

4.19.1 Repairs must comply with all applicable safety requirements, including vehicle frame alignment, airbag system integrity, and proper restoration of safety systems.

4.20 Quality Control Standards

4.20.1 The vendor must implement a documented quality control process to verify repairs before presenting the vehicle for

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 10 of 20

City inspection.

4.21 Paint and Finish Standards

4.21.1 All refinishing work must match existing color, texture, and gloss, with no overspray, mismatched panels, or surface defects.

4.22 Environmental Compliance Standards

4.22.1 Vendors must comply with applicable environmental

regulations, including proper handling and disposal of paint waste, solvents, used oil, antifreeze, and other regulated materials.

4.23 Cleanliness and Work Area Standards

4.23.1 Vehicles must be returned clean, free of debris, and

without damage unrelated to the original repair.

4.24 Documentation Standards

4.24.1 Repair estimates, supplements, parts lists, and invoices must be accurate, itemized, and submitted according to City requirements.

4.25 Timeliness Standards

4.25.1 Repairs must be completed within agreed-upon timeframes unless a delay is approved by the City.

4.26 Parts Standards

4.26.1 Only OEM, OEM-approved, or City-authorized

alternative parts may be used. Parts must be new unless the city approves refurbished or recycled components.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 11 of 20

4.26.2 Completion of this inspection and approval process is

mandatory before any invoice will be accepted or payment processed.

5.0 WARRANTY

5.1 The effective warranty date up to the following standards below must be the date final acceptance of the repaired vehicle by City of Fort Worth. Warranty does include coverage of normal wear and tear items.

5.2 Auto Body & Collision Parts and Labor – (5) years from

the completion of the repair.

5.3 Auto Body & Collision Paint – (5) years from the

completion of the repair

5.4 Mechanical & Electrical Parts and Labor - Minimum of

one

(1) year from the completion of repair.

5.5 All wear and tear items are items needed to be stated

within the warranty.

6.0 RESPONSE TIMES

6.1 Vendors must respond to written correspondence from the

City’s point of contact (Property Managements contact) within 48 hours.

7.0 TIME, HOLIDAYS, AND LOCATIONS

7.1 If requested, Vendors shall deliver completed vehicles to the James Ave Fleet Service Center, during these work times: Monday through Friday between 7:30 a.m.– 4:30 p.m. unless expressly authorized by the Fleet Service

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 12 of 20 RFP Title: Auto Body Shop Repairs

Center Supervisor(s) or their designee. Any deviation from this timeframe requires written approval from the City of Fort Worth Property Management Department, Fleet Division Assistant Director or assigned designee.

7.2 After hours will be Friday at 4:31 p.m. through Monday

at 7:29 a.m.

7.3 All observed City holidays:

7.3.1 New Year’s Day

7.3.2 Martin Luther King Jr. Day

7.3.3 Memorial Day

7.3.4 Juneteenth, Independence Day

7.3.5 July 4th

7.3.6 Labor Day

7.3.7 Thanksgiving Day (Thurs and Fri)

7.3.8 and Christmas Day.

7.3.9 Vendor shall not perform any emergency holiday work

without the written approval from the City of Fort Worth Property Management Department, Fleet Division Assistant Director or assigned designee.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 13 of 20

7.4 City of Fort Worth PMD, Fleet Division Service Center Locations:

JAMES AVE

SERVICE CENTER

5021 James Ave

Fort Worth, TX 76115

NORTH SERVICE

CENTER

317 Hillshire Dr.

Fort Worth, TX 76052

WATER SERVICE

CENTER

2222 W. Daggett Ave.

Fort Worth, TX 76104

EMS WEST

SERVICE CENTER

2900 Alta Mere Drive Fort Worth, Texas

76116

7.5 City reserves the right to add or remove locations during the life of the contract.

7.6 City of Fort Worth PMD, Fleet Division will notify

the vendor upon addition or removal of locations through amendment execution.

8.0 ESTIMATES

8.1 The vendor is required to provide all written estimates.

8.2 All estimates provided by the vendor shall be quoted on

a 'time and materials' basis, adherence to the agreed upon contract rate(s) and itemized to illustrate the cost of each of the following services or work performed.

8.3 Vendor shall only begin work once a Purchase Order

is issued.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 14 of 20

8.4 During the course of the originally estimated repairs, it is noted that further repairs will be needed, a revised estimate must be prepared by the vendor for the additional work and emailed to City of Fort Worth Property Management Department, Fleet Division Assistant Director or assigned designee for approval.

8.5 Revised estimates must be approved and authorized by

City of Fort Worth Property Management Department, Fleet Division Assistant Director or assigned designee in writing prior to work being performed.

9.0 REPORTING

9.1 Vendors must submit a weekly repair status report to the

authorized City of Fort Worth Property Management Department Fleet Division Assistant Director or assigned designee representative with the vehicle number, date received, and a detailed status of each vehicle number and the estimated completion date. Also, listed should be any items on hold or other delays which need to be made for the attention of the City of Fort Worth Property Management Department Fleet Division Assistant Director or assigned designee representative.

10.0 INVENTORY OF ASSETS

10.1 Assets that may need auto body collision repair services, include, but are not limited to, the inventory listed below

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 15 of 20

Up to 9,000 on-road vehicles and equipment including trailers, but not limited to, the following manufacturers:

Ford

GM

Dodge Nissan and other related manufacturers over 1 ton

11.0 METHOD OF AWARD - Proposals will be evaluated based on “best value” to the city. Proposals that receive less than 50% of the total available points, excluding price points, will not be considered for award.

12.0 EVALUATION FACTORS

To be considered, the Proposer must submit a complete Proposal by the stated deadline and in accordance with all Proposal requirements. All required documentation must be included for evaluation.

Proposals that meet these requirements will be evaluated based on the criteria listed below.

12.1 Cost – up to 20 points available

12.2 Staffing Levels – up to 20 points

12.3 Experience and Qualifications – up to 20 points

12.4 Methodology for providing Auto Body Collision Repairs and

Service- up to 20 points

12.5 Small Business – up to 20 points

13.0 PRICING STRUCTURE

• Clearly outline how pricing must be presented (fixed price, hourly rate, unit cost)

• Contractor must allow Property Management for three (3) days of inspection of all orders of services. The department representative or

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 16 of 20 RFP Title: Auto Body Shop Repairs designee will sign forall pickups and deliveries services that have met satisfactory standards. This is a requirement before invoice and payment can be processed.

14.0 CONTRACT AWARD PROCESS

14.1 The Purchasing Division will facilitate and manage the

evaluation process.

14.2 An Evaluation Panel consisting of representatives from various

City departments and City consultants may be appointed to review and evaluate RFP responses in accordance with this RFP. City reserves the right at its sole discretion to include additional representatives at any point during the evaluation.

14.3 The Evaluation Committee will evaluate responses and may select Proposer for onsite interviews, presentations or demonstrations.

14.4 At its sole discretion, the City may request Best and Final Offers

(BAFO) from proposers whose proposals are deemed most advantageous. Contract negotiations will be based on the BAFO submissions.

14.5 The City reserves the right to negotiate all elements that comprise the successful Proposer’s response to ensure that the best possible consideration be afforded to all concerned.

14.6 The City reserves the right to shortlist firms based upon scores/ratings received during the evaluation process.

14.7 The City will notify all proposers in writing of the outcome once an award determination has been made.

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 17 of 20

15.0 ROPOSAL FORMAT AND ATTACHMENTS

To facilitate and expedite the evaluation process, Proposals should adequately address all evaluation factors and include the following list of required items that will be used as part of the evaluation. A Proposal may be deemed to be non-responsive and may be disqualified, at the City’s discretion, if the Proposal fails to comply with the following instructions.

15.1 Proposal Format Requirements

15.1.1 Proposal format shall be in font no smaller than 12

point, 8.5-inch by 11-inch paper size, with one-inch margins and single-spaced for the entire submitted proposal.

15.1.2 All proposal sections shall be divided by submission titles.

All pages within these sections shall be uniquely numbered for purposes of easy reference.

15.2 Response forms

15.2.1 Completed and signed RFP-04.

15.2.2 Completed and signed RFP-05.

15.2.3 Completed and signed RFP-06.

15.2.4 Completed and signed RFP-07.

15.2.5 Completed Bid Table (BT-28HI)

15.3 Technical Response

15.3.1 List of Exceptions/Substitutions/Clarifications/Additions

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 18 of 20

15.3.1.1 Although the Scope of Services included Project

Requirements of the solicitation represents the City’s anticipated needs, there may be instances in which it is in the City’s best interest to permit exceptions to requirements and accept proposed alternatives.

15.3.1.2 If no exceptions are taken, please include a

single document stating “No Exceptions taken” in the Required section.

15.3.1.3 It is extremely important for the Proposer to make

clear where exceptions, clarifications substitutions and/or additions to the Scope of Services, Draft Vendor Service Agreement and General Terms and Conditions are taken and how substitutions shall be provided. The city does not recognize strikeouts, deletions, or changes to Solicitation documents. Therefore, exceptions, conditions, clarifications and/or substitutions to the provisions of the City’s requirements must be clearly identified along with the proposed addition or modification. If the Proposer does not make it clear that an addition, exception or clarification is taken, the City shall assume the Proposer is responding to and shall meet the City’s stated requirements.

15.3.1.4 Identify each exception, clarification, substitution and/or addition by specifically referencing the page number, section number, subsection number, item number or letter, and, if necessary, paragraph, or line number.

15.3.1.5 Identify each item clearly as an addition, exception, clarification or substitution. It is not necessary to include the entire text of a particular section or subsection. However, for ease of

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 19 of 20 RFP Title: Auto Body Shop Repairs reference, Proposers may use portions of the solicitation’s text, if helpful in explanation.

15.3.1.6 For substitutions/clarifications, provide an

explanation of the difference between what the solicitation requests and what is proposed. The city is open to other means of accomplishing the requested Work. Proposers must explain why they believe their method of accomplishing the Work is equal to or better than that specified by the City.

15.3.1.7 For any addition(s) proposed or exception(s)

taken, provide a rationale in as much detail as possible.

15.3.1.8 Begin responses to the major sections of

the solicitation on a new page.

15.3.1.9 The city shall consider the number and substance

of alterations to the city’s stated requirements as a factor in determining the most advantageous response.

15.3.2 Pricing

15.3.2.1 Proposal pricing shall be assembled and presented

in accordance with the format and instructions of this solicitation.

SMALL BUSINESS PROGRAM – The City of Fort Worth has established a 30% Small Business (SB) participation goal for this solicitation. This goal reflects the City’s determination that certified Small Business Firms are available to provide the goods and/or services required under this bid. Accordingly, at least 30% of the total awarded contract value must be subcontracted or spent with a certified Small Business Firm. All provisions and requirements outlined in City Ordinance No.

27832-08-2025 apply to this solicitation. Bidders are required to submit the following documentation with their proposal:

RFP Ref. #: 27-0024 Doc. Ref#: RFP-02 Page 20 of 20 RFP Title: Auto Body Shop Repairs

a. Small Business Utilization form V1 (RFP-05), detailing how the Small Business goal will be achieved.

b. Current Small Business Certification issued by a certifying entity approved by the City Manager.

1.0 INTRODUCTION AND PURPOSE
2.0 SCOPE OF SERVICES
3.0 PARTS
4.0 QUALIFICATIONS
4.17 Workmanship Standards
4.18 OEM Repair Procedures
4.19 Safety Standards
4.20 Quality Control Standards
4.21 Paint and Finish Standards
4.22 Environmental Compliance Standards
4.23 Cleanliness and Work Area Standards
4.24 Documentation Standards
4.25 Timeliness Standards
4.26 Parts Standards
7.0 TIME, HOLIDAYS, AND LOCATIONS
8.0 ESTIMATES
9.0 REPORTING
10.0 INVENTORY OF ASSETS
12.0 EVALUATION FACTORS
13.0 PRICING STRUCTURE
14.0 CONTRACT AWARD PROCESS
15.0 ROPOSAL FORMAT AND ATTACHMENTS
15.3 Technical Response

File details come from the government source that posted it. Updated .