final bpa pkg.doc

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

6. SOLICITATION ISSUE DATE

INFORMATION CALL:

DESTINATION UNLESS

12. DISCOUNT TERMS

UNRESTRICTED

BLOCK IS MARKED

FORMCHECKBOX

SEE SCHEDULE

13a. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

HUBZONE SM. BUSINESS BUSINSESS

13b. RATING

8(A)

FORMCHECKBOX

IFB

FORMCHECKBOX

RFP

CHICAGO, IL 60604

17a. CONTRACTOR/OFFEROR

OFFEROR

FORMCHECKBOX

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER

FORMCHECKBOX

SEE ADDENDUM

(Attach Additional Sheet as Necessary)

X27a. solicitation incorporates by reference FAR 52.212-1, 52.212-4. FAR 52.212-3 and 52.212-5 are attached.

Addenda Xare FORMCHECKBOX are not attached.

FORMCHECKBOX

27b. contract/purchase order incorporates by reference FAR 52.212-4. FAR 52.212-5 is attached.

Addenda FORMCHECKBOX are FORMCHECKBOX are not attached.

28.

X

FORMCHECKBOX

AWARD OF CONTRACT: REFERENCE OFFER DATED . YOUR OFFER ON SOLICITATION (BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

AUTHORIZED FOR LOCAL REPRODUCTION

STANDARD FORM 1449 (REV. 3/2005)

Previous Edition Is Not Usable Prescribed by GSA ( FAR (48 CFR) 53.212

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED

FORMCHECKBOX

INSPECTED

FORMCHECKBOX

ACCEPTED, AND CONFORMS TO THE CONTRACT EXCEPT AS NOTED:

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

33. SHIP NUMBER

PARTIAL FORMCHECKBOX

FINAL

FORMCHECKBOX

COMPLETE FORMCHECKBOX

PARTIAL FORMCHECKBOX

FINAL

37. CHECK NUMBER

42b. RECEIVED AT (Location)

STANDARD FORM 1449 (REV. 3/2005) BACK

1. This Blanket Purchase Agreement is issued to establish arrangements for ordering, shipping, and billing to cover merchandise purchased. The essence of this arrangement is that a contractor will be awarded a Blanket Purchase Agreement for providing specified hand tools to satisfy numerous small requirements for a specified period of time to be shipped to any destination within the 48 contiguous states and the District of Columbia. Price break quantities may be solicited on some National Stock Numbers in order to provide coverage for the small quantity purchase orders. The availability of items in smaller quantities is essential for our customers to achieve their missions.

2.

Resultant awards will be based on a best value determination. Consideration could be given to vendor performance history, delivery time, and/or price.

3.

This agreement does not obligate the Government to order or the contractor to furnish any articles on any quantity except to the extent that may be agreed upon in connection with individual transactions. In the event that this arrangement is applied in connection with ordering material available under Federal Supply Schedule contracts, or other established contracts, nothing herein shall be deemed to modify the terms and conditions of such contracts.

4.

Agreement is made in accordance with negotiation authority of Federal Acquisition Regulation 13.303 - Blanket Purchase Agreements.

5.

Notwithstanding any requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventive finish that is used in standard commercial practice shall apply.

6. PRICING: The prices to the Government shall be as low or lower than those charged the supplier’s most favored customer for comparable quantities under similar terms and conditions in addition to any discounts for prompt payment. ALL prices requested FOB Destination (see clause 52.247-34).

7. The minimum purchase order dollar amount for items awarded under this agreement is $15.00, If less then required $15.00 minimum, please indicate the lowest minimum order amount you will accept:

. (Offerors are encouraged to submit lower minimum order amounts)

8. No single purchase under this arrangement shall exceed $24,999 in amount.

9. In the event of a price increase, the price herein quoted will remain in effect for a reasonable period (30 days) from the date of the contractor’s written notice of such increases to allow the Government sufficient time for update pricing. Any price increase request must be supported by sufficient documentation to justify the price increase. The documentation must be submitted with the price increase request. Price increase requests may be submitted semi-annually, as needed.

NOTE: All purchase orders issued during the 30-day period at the old prices are to be accepted and processed. No price changes to purchase orders issued before or during this timeframe will be allowed. Where the Government fails to make the necessary computer changes within the 30-day period, purchase orders will be amended to reflect the approved increased price.

10. Delivery Days will be: 30 Days ARO or less, please indicate your delivery time, if less than 30 days:

11. Inspection & Acceptance

a. Inspection and acceptance will be at destination.

b. All purchase orders, which may be issued under the Blanket Purchase Agreement for direct delivery to the GSA customer, will be subject to and include the attached terms and conditions.

c. Supplies shall be shipped prepaid by common carrier, parcel carrier or parcel post (unless other specified on individual purchase orders)

12. OPTION TO EXTEND THE TERM OF THE AGREEMENT: The term of this agreement may be extended by mutual consent of the parties, provided:

a.

Con tractor will be contacted within thirty (30) days of expiration of the current agreement if the government intends to extend the BPA (this notice shall not be deemed to commit the Government to an extension).

b.

The extension shall be a period of no more than 60 days..

13. By signing below you are certifying that the products being offered meet the salient characteristics of the Item Purchase Description (IPD), and meet Buy American Act Requirments made. Failure to meet these requirements may result in your bearing the costs of:

a. Replacing items

b. Shipment to replace

c. Government re-procurement

Offeror’s Name and Signature

Date

14. BPA may be cancelled for default immediately, by the government, if contractor is noncompliant with terms and conditions of agreement.

15. AWARD: Clause M-FSS-301-A, Method of Award (4/84) is incorporated to cover item-by-item awards.

16. Agreement may be cancelled by either party at no cost with 30 day written notice.

17.

Contractor's personnel to contact:

NAME: ______________________________________

CO. DUNS #: ____________________ TIN: ______________________

ADDRESS: ______________________________________________

CITY: ______________________ STATE: ____ ZIP CODE: ________

TELEPHONE: _________________ FAX: ______________________

18. NOTICE OF INDIVIDUAL AUTHORIZED TO PURCHASE UNDER THE BPA: Contract Specialists and Purchasing Agents located at:

19. The following 20 of 25 item numbers are set-aside for small business: 1,2,3,4,5,6,7,11,12,13,14,15,16,17,19,20,21,22,23,24,25.

20. Item Numbers NOT set-aside are: 8,9,10,13,18

GSA, FAS, Heartland Global Supply QSDAAA 1500 East Bannister Road Kansas City, MO 64131-3088.

PLACE OFFERS HERE

6FLS-N1-083930-I

FOB Destination

Number

Est. Qty.

Price (your offer)

1.

5130-00-074-9952

2.

5130-00-099-3688

3.

5130-00-117-4793

4.

5130-00-190-6440

5.

5130-00-234-4881

6.

5130-00-288-7743

7.

5130-00-288-7745

8.

5130-00-293-1154

9.

5130-00-473-6224

10.

5130-00-506-4854

11.

5130-00-533-0235

12.

5130-00-542-3276

13.

5130-00-580-2305

14.

5130-00-596-0962 24 $_______

15.

5130-00-596-9715 98

16.

5130-00-760-1360

17.

5130-00-760-9677

18.

5130-00-770-6130

19.

5130-00-772-7804

20.

5130-00-778-1675

21.

5130-00-880-4586

22.

5130-00-889-1841

23.

5130-00-889-8985

24.

5130-00-890-5503

25.

5130-00-932-1518

ITEM PURCHASE DESCRIPTION’S 6FLS-H8-085090-I

1. 5130-00-074-9952 UI: EA

RIVETER SET, BLIND PNEUMATIC:

DESCRIPTION

Set is designed to install Military Specification MS20600 Series rivets, Cherry Division of Textron serrated stem Series 9000 rivets, and Cherrylock spindle Series 2000 rivets, when riveter is assembled with appropriate pulling head and operated in accordance with the manufacturer's instructions. It shall operate on an air pressure of 90 to 125 PSI, develop at least 2,850 pounds of pull at the nose and have a stroke of 1-1/16 inch minimum.

Carrying Case shall be made of 0.050 inch minimum thick steel with formed corners, a full piano hinge, a heavy duty snap latch, a formed metal handle secured by welding or rivets and painted to manufacturer's standard practice. Case shall be large enough to hold and contain the riveter and have separate compartments for each nose assembly, and one (1) compartment for the other accessories. Means shall be provided to prevent movement of components when transported and case shall not open when filled with all the components when carried by the handle.

One (1) copy of the manufacturer's operation instuctions, maintenance manual, and parts list shall be furnished with each riveter set. All parts shall be functionally and mechanically interchangeable with Cherry Series H9040 and H640B pulling heads and Gage Bilt Series 740 and 640 nose assemblies. Pulling heads shall be capable of being used on Cherry Model G740A Rivet Gun or Gage Bilt Model GBP740A rivet gun.

Mark each component and set in a permanent and legible manner with manufacturer's part number and name or identifying symbol.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

2. 5130-00-099-3688 UI: EA

NOSE ASSEMBLY, RIVETER:

DESCRIPTION

General Characteristics Item Description:

Type - Straight, unimatic, stake lock collar type

Overall length of nose assembly beyond installation tool - 2.06 inches +/- 0.030 inch

Overall Diameter -0.750 inch +/- 0.015 inch.

Functional Description - Used to install Huck Mfg. Co. mechanical lock series SB-06 blind bolt fasteners

End Item Identification - Functionally and mechanically compatible with Huck Mfg. Co. installation tool models 200, 352, 356, AND 2700.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

3. 5130-00-117-4793 UI: EA

DRILL, ELECTRIC, PORTABLE:

DESCRIPTION

Style: Straight drive with pistol grip and keyed jaw chuck.

Voltage: 120V AC.

Frequency: 60 Hertz single phase.

Current Rating: 6.5 amps minimum.

Drill Size: 3/8".

No Load Speed: 1000 minimum - 1200 maximum RPM.

Connector Type: Two-prong plug.

Features: Variable speed and reversible. Double insulated and shockproof.

Special Feature: Drill shall have a minimum motor life of 500 hours.

Drill shall be furnished with chuck key and operation instructions and maintenance handbook.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

4. 5130-00-190-6440 UI: EA

HAMMER, PNEUMATIC, PORTABLE:

DESCRIPTION

This technical description covers an "L" type handle, portable, pneumatic hammers intended for use in chipping, scaling, ironing, creasing, bending, and forming metal.

Salient Characteristics:

General construction - The chipping hammers supplied in accordance with this description shall be of the manufacturer's current design. The hammers shall operate properly at air supply pressures between 80-100 psig. All components shall be new and unused. Repaired or reconditioned components shall not be acceptable. Metal housing is required. Cadmium is not an acceptable plating.

The pneumatic portable hammer shall comply with the following performance and design characteristics:

##Bore and Stroke - 1-1/8 x 3 inches

Air Consumption (Maximum) - 36 CFM

Impact Frequency (Minimum) - 1700 impacts per minute

##Note - Tolerance for Bore shall be plus or minus 5 percent and the Stroke shall be the manufacturer's nominal rated stroke.

Throttle - The hammers shall be actuated by a non-leaking manual throttle. The throttle lever shall be the deadman type and shall permit easy admission and accurate regulation of the compressed air. The lever shall be conveniently located on the outside of the "L" type open handle.

Air inlet: The air inlet shall be a well secured, brass or ferrous 3/8 inch NPT fitting located at the end of the handle. The air inlet shall be fitted with an air strainer or screen (20 mesh or finer) which shall effectively retain solid particles in compressed air supply. The strainer or screen shall be of such a design that it can be easily removed for cleaning.

Lubrication - Parts requiring lubrication shall be protected from the entrance of foreign matter and loss of lubricant. The hammers shall provide for the delivery of lubricant in a manner that will assure proper operation.

Chisel bushing - The bushing shall accommodate a commercial chisel shank style 0.580-inch width across the flat (hex.) and 1-3/4 inches long. The shoulder shall have a 0.680-inch diameter (round) and shall be 5/8-inch long.

Accessories - The hammers shall be furnished with retainers which will accommodate hexagon shank Navy standard oval collared chisels, a complete set of the manufacturer's current operating and maintenance instructions, a parts list breakdown, any special tools necessary to assure efficient operation in accordance with the instructions, and any tools, equipment, and accessories normally supplied commercially.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

5. 5130-00-234-4881 UI: EA

WRENCH, IMPACT, PNEUMATIC, PORTABLE (BODY GRIP)

DESCRIPTION

Pneumatic Impact Wrench

The pneumatic impact wrench shall meet the following design and performance criteria:

Spindle Square Drive Size (inch) - 3/8 inch

Spindle Offset (Maximum) - 1-1/4 inch

Air Inlet, NPT, NPTF - 1/4 inch

Air Consumption While Impacting (Maximum) - 15 CFM

Developed Torque After 5 Seconds Impacting - 50 ft-lbs

Handle Design - Body Grip

Air Operating Pressure Range - 80 to 100 psig

Salient Characteristics:

Material - The material used in the construction of the wrenches shall be of good commercial quality suitable for the intended purpose. All materials used shall be free from defects and imperfections that may adversely affect the serviceability of the finished product. A metal or composite housing is required. Cadmium is not an acceptable plating on any component.

Lubrication - Provisions shall be made for lubrication to be supplied to moving parts in the path of the air stream. The oil may be applied manually into the motor or supplied automatically through the air supply line. Other suitable means shall be provided for supplying lubrication to moving parts not in the air stream.

Air inlet connection - The air inlet connection shall consist of a well-secured ferrous fitting threaded with internal American Standard taper pipe threads (NPT) or internal Dryseal American Standard taper pipe threads (NPTF) as specified in Table I. The air inlet shall be fitted with an air strainer or screen (20 mesh or finer) which shall be effective in preventing solid particles in the compressed air supply from entering the tool. The strainer or screen shall be of such design that it can be easily removed for cleaning.

Spindle - The drive end of the spindle shall be wear-resistant. The drive end, when fitted with a socket, shall not show excessive run-out which may adversely affect operation of the wrench. The drive end of the spindle shall conform to ANSI B107.4, spring loaded plunger or through hole design.

Operation - The wrenches shall be reversible. The rotational direction of the wrench shall be controlled by a conveniently located mechanical device which is independent of the throttle. The rotational control shall be plainly and permanently marked to indicate direction of rotation.

Impact unit - Wrenches shall contain an impact unit which is actuated by the motor. The impact unit shall be designed to convert torque from the motor into rotary impacts and to transmit the impacts to the spindle.

Throttle - Wrenches shall be provided with a nonleakable manual throttle for controlling the supply of compressed air. The wrench shall be equipped with a lever style throttle.

Manual - One copy of a technical manual consisting of the manufacturer's standard commercial instruction and parts list shall be furnished with each tool.

Air volume (torque regulator) - The wrenches shall be furnished with an air volume (torque) requlator. The requlator shall be built into the tool. The regulator shall have varying degrees of restriction for regulating the volume of air flow.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

6. 5130-00-288-7743 UI: EA

DRILL, PNEUMATIC, PORTABLE:

DESCRIPTION

The pneumatic drill covered by this technical description is intended for drilling holes in metal, using twist drills. Maximum sound pressure levels shall be set to insure against occupational noise-induced hearing losses. The tools covered by this technical description are considered intermittent duty tools, used in short burst of 2 minutes duration or less. The exposure time for this tool should be four (4) hours.

Salient Characteristics:

Design and construction - The drill shall be of rugged construction so as to withstand, without failure, treatment likely to be encountered under general service conditions. Drills shall be self contained, readily accessible for adjustment or replacement of parts. Parts which require lubrication shall be properly enclosed so as to prevent entrance of foreign particles and leakage of lubricant. Working parts exposed to wear shall be of sufficient hardness to withstand the services required. Parts shall be properly finished by machining or grinding to dimensions within limits established by good commercial practice. The drill shall be reliable and effective when operated on compressed air lines at gage pressures between 80 and 100 pounds per square inch gage (psig). The rotational control shall be plainly and permanently marked to indicate direction of rotation.

Interchangeability - All parts having the same manufacturer's part number shall be constructed to definite standards, tolerances, and clearance in order that such parts may be completely interchangeable and may be replaced or adjusted without requiring modification.

Sound pressure levels - The sound pressure levels as measured at an unobstructed distance of one meter, shall not exceed 100 dBA.

Throttle: The throttle shall control the speed of the tool and automatically shut off the air supply when released. A lock-on device may be provided if turnoff can be accomplished by a single motion of the same finger or fingers that actuated it.

The drill shall conform to the following design and performance requirements:

Reversible

Straight Drive

Size - 2 inch diameter high speed twist drill capacity

Air Inlet Connection - 3/4 or 1 inches Nominal Pipe Size

Weight - 45 pounds maximum

Speed @ 80 ft-lbs Torque - 150 RPM minimum

Air Consumption @ 80 ft-lbs Torque - 50 scfm/hp maximum

Speed @ No-load - 310 RPM maximum

Chuck Size - No. 4 ASA Morse Taper Socket

Metric product - Product manufactured to metric (SI) dimensions shall be considered on an equal basis with those manufactured using inch-pound units of measure, provided they fall within the specified tolerances using conversion tables contained in the latest revision of ASTM E 380, Standard Practice for Use of the International System of Units (SI), and all other requirements of this technical description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable.

Regulatory Requirements

Occupational Safety - The drill shall conform to Occupational Safety and Health Act (OSHA), 29 CFR 1910.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

7. 5130-00-288-7745 UI: EA

DRILL, PNEUMATIC, PORTABLE:

DESCRIPTION

The pneumatic drill covered by this specification is intended for drilling holes in metal, using twist drills. Maximum sound pressure levels shall be set to insure against occupational noise-induced hearing losses. The tools covered by this technical description are considered intermittent duty tools, used in short burst of 2 minutes duration or less. The exposure time for this tool should be four (4) hours.

Salient Characteristics:

Design and construction - The drill shall be of rugged construction so as to withstand, without failure, treatment likely to be encountered under general service conditions. Drills shall be self contained, readily accessible for adjustment or replacement of parts. Parts which require lubrication shall be properly enclosed so as to prevent entrance of foreign particles and leakage of lubricant. Working parts exposed to wear shall be of sufficient hardness to withstand the services required. Parts shall be properly finished by machining or grinding to dimensions within limits established by good commercial practice. The drill shall be reliable and effective when operated on compressed air lines at gage pressures between 80 and 100 pounds per square inch gage (psig). The rotational control shall be plainly marked to indicate direction of rotation.

Interchangeability - All parts having the same manufacturer's part number shall be constructed to definite standards, tolerances, and clearance in order that such parts may be completely interchangeable and may be replaced or adjusted without requiring modification.

Sound pressure levels - The sound pressure levels as measured at an unobstructed distance of one meter, shall not exceed 100 dBA.

Throttle: The throttle shall control the speed of the tool and automatically shut off the air supply when released. A lock-on device may be provided if turnoff can be accomplished by a single motion of the same finger or fingers that actuated it.

The drill shall conform to the following design and performance characteristics

Type: Drill, Reversible

Style: Straight Drive

Size: 7/8 inch

Air Inlet Connection - 1/2 or 3/4 inches Nominal Pipe Size

Weight - 28 pounds maximum

Speed @ 30 ft-lbs Torque - 375 RPM minimum

Air Consumption @ 30 ft-lbs Torque - 45 scfm/hp maximum

Speed @ No-load - 500 RPM maximum

At Spindle - No.3 ASA Morse Taper Socket

Metric product - Product manufactured to metric (SI) dimensions shall be considered on an equal basis with those manufactured using inch-pound units of measure, provided they fall within the specified tolerances using conversion tables contained in the latest revision of ASTM E 380, Standard Practice for Use of the International System of Units (SI), and all other requirements of this technical description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable.

Regulatory Requirements

Occupational Safety - The drill shall conform to Occupational Safety and Health Act (OSHA), 29 CFR 1910.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

8. 5130-00-293-1154 UI: EA

BORER, WOOD, PNEUMATIC:

DESCRIPTION

The wood borer covered by this specification is intended for use in drilling holes in wood, using wood bits. Maximum sound pressure levels shall be set to insure against occupational noise-induced hearing losses. The tools covered by this technical description are considered intermittent duty tools, used in short burst of 2 minutes duration or less. The exposure time for this tool is two hours.

Salient Characteristics:

Design and construction - The borer shall be of rugged construction so as to withstand, without failure, treatment likely to be encountered under general service conditions. Drills shall be self contained, readily accessible for adjustment or replacement of parts. Parts which require lubrication shall be properly enclosed so as to prevent entrance of foreign particles and leakage of lubricant. Working parts exposed to wear shall be of sufficient hardness to withstand the services required. Parts shall be properly finished by machining or grinding to dimensions within limits established by good commercial practice. The drill shall be reliable and effective when operated on compressed air lines at gage pressures between 80 and 100 pounds per square inch gage (psig). The rotational control shall be plainly and permanently marked to indicate the direction of rotation.

Interchangeability - All parts having the same manufacturer's part number shall be constructed to definite standards, tolerances, and clearance in order that such parts may be completely interchangeable and may be replaced or adjusted without requiring modification.

Sound pressure levels - The sound pressure levels as measured at an unobstructed distance of one meter, shall not exceed 100 dBA.

Throttle: The throttle shall control the speed of the tool and automatically shut off the air supply when released. A lock-on device may be provided if turnoff can be accomplished by a single motion of the same finger or fingers that actuated it.

The drill shall conform to the following design and performance characteristics:

Type: Wood Borers.

Size: 2" reversible.

Chuck Size for Woodbit Shanks: 1/2" diameter.

Horsepower: 1.5 minimum.

Air Consumption: 40 scfm/HP maximum.

Air Inlet Connection: 1/2" or 3/4" Nominal Pipe Size.

#In spindle: ASA Morse Taper Socket No. 2.

Weight: 17.0 pounds maximum.

Speed At No Load: 850 RPM maximum.

#Spindle - Wood borers shall be equipped with spindles having standard ASA morse taper sockets of the size shown in the above, threaded externally on its outer end in accordance with the manufacturer's standard practice, and shall be furnished with chucks suitable for retaining a shank of the size shown in above.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

9. 5130-00-473-6224 UI: EA

DRILL, ELECTRIC, PORTABLE:

DESCRIPTION

The electric drill covered by this specification is a compact portable tool with universal motor for operation using 115 volt DC and 115 volts 25 to 60 cycles AC. This drill is used for continuous heavy duty drilling of mild steel.

Salient Characteristics:

Standard product - The drills furnished under this purchase description shall be the manufacturer's current standard products including accessories and optional components that are offered to the commercial market. All accessories and options shall be identified with proposals tendered to the government in response to solicitations citing this document.

Design - The design shall be such as to provide convenient and safe operation. The drill shall be either double-insulated or of the 3-wire grounding construction All materials used in the fabrication of this drill shall be new. The drill shall be complete so that when connected to the specified power source it can be used for its designed operation.

Interchangeability - All parts having the same manufacturer's number shall be manufactured to such standards that will permit replacement or adjustment without modification of the electric drill.

Motor - The motor shall be universal, series wound or compensated series wound designed to operate on either 120 volt (+,- 10 percent) direct current (DC), or 120 volt (+,- 6 percent), single-phase, 25-60 cycle, alternating current (AC). The motor shall conform to the requirements of UL 45.

Switch - Each drill shall be provided with a convenient located switch for turning the current of the motor "OFF" and "ON". The inclusion of a locking pin or similar means for holding the switch in the "ON" position shall be at the option of the contractor. All switches shall be double pole. The switches shall be rated for both AC & DC operations. The switches except those which release automatically, shall be marked plainly to show the "OFF" and "ON" position. The switches shall comply with the requirements of UL 45.

Wiring, cord, and plug cap - The wiring, flexible cord, and attachment plug cap shall be in accordance with UL 45, as applicable. The cord shall have an attachment plug cap and unless otherwise specified in the ordering data, shall have a minimum free length of 8 feet measured from point of entry into the drill. The attachment plug cap shall comply with UL 45 requirements for two-pole, three-wire grounding devices rated 15 amperes at 125 volts.

NEMA - Motors shall conform to National Electrical Manufacturers Association (NEMA) Publication No. MG-1.

UL - All electrical components including motors, switches, and wiring shall conform to the applicable requirements of UL-45. Each drill shall bear and identification plate in accordance with the applicable requirements of UL-45. Unless otherwise specified, each drill shall be furnished with an instruction manual in accordance with the applicable requirements of UL-45.

Performance - Each drill shall conform to the following design and performance requirements:

Medium Speed Drill, With Stand.

Heavy Duty

Style - Straight Drive

Size - 3/8 inch

Handle Style - Closed End Grip

Drive End Type - Keyed Jaw Chuck

*Chuck Capacity - 3/8 inch minimum

Weight without cord - 15.0 pounds maximum

Length Overall - 18 inches maximum

Spindle RPMS @ No-load - 1200 maximum

Spindle RPMS @ Rated Load - **400 - 660

Rated Load Amps @ 120 Volts AC - 3.5 Amps minimum

Torque @ Spindle Shaft - 3.0 foot-pounds minimum at Rated Load

Stall Torque @ Spindle Shaft - 15.0 foot-pounds minimum

*Note - 1/2 inch chuck may be provided so long as all performance requirements for the size 3/8 inch drill are met.

**Note - The rated load speed shall in no case be less than 55 percent of the rated no load speed.

Stand - The drill stand shall be designed for holding an electric drill with the characteristics specified above within this technical description. The stand shall consist of a base, column, drill mounting fixture, and operating lever. The base shall be a casting with top machined flat as a table working surface and provided with at least two integral lugs with holes for bench mounting. The base shall be provided with a means for mounting and rigidly holding a round column. The column shall be of a diameter to fully support the drill in operation and shall be accurately machined. The column shall be of sufficient height to provide the vertical adjustment specified in Table II. of this technical description for the size specified. The drill mounting fixture shall be designed for securely holding the drill with mounting brackets fitted to and mounted on the column. The column clamp, spring, and operating level providing feed shall be included in the design. The column clamp shall be fitted to the column and be adjustable to any position within the adjustment range. The spring shall be heavy enough to immediately return the drill to the top position when the lever is released. The lever shall provide a leverage ratio of at least 3-1/2 to 1

The stand shall accommodate the drill and comply with the following:

Size - 3/8 inches

Electric drill, size - 3/8 inches

"Capacity Swing" face of column to center of chuck - 5-1/2 inches minimum

"Feed" travel of drill in clamped position - 4 inches at least

Vertical adjustment on column - 12 inches (maximum height drill chuck to base) (At least)

Weight complete with drill - 65 pounds maximum

Working surface of base size - 50 square inches (approximately)

Electromagnetic interference suppression - Not provided

Accessories - The drill shall be supplied with maintenance tools, extra parts, accessories, attachments, and complete operating and maintenance instructions as normally furnished commercially.

Carrying case - Each drill shall be provided within a rigid, sturdy, impact resistant, plastic or metal carrying case. The carrying case shall be of sufficient size to contain and secure the drill, maintenance tools, and accessories. The case shall be complete with a hinged cover, carrying handles, and closing fasteners.

Metric product - Products manufactured to metric (SI) dimensions shall be considered on an equal basis with those manufactured using inch-pound units of measure, provided they fall within the specified tolerances using conversion tables contained in the latest revision of ASTM E380, Standard Practice for Use of the International System of Units (SI), and all other requirements of this technical description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable.

Regulatory Requirements:

Occupational Safety - Electrical drills shall conform to Occupational Safety and Health Act (OSHA), 29 CFR 1910.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

10. 5130-00-506-4854 UI: EA

ANGLE ATTACHMENT, DRILL CHUCK:

DESCRIPTION

Function Identification - Light duty angle drill attachment designed for use with electric or pneumatic drill in close quarters

Drill attachment - The angle drill attachment shall have a die cast or steel housing with a 90 degree fixed angle head on one end

Drive Shaft - Overall steel hardened and ground. A 1/4 inch diameter, 3/4 inch minimum length drive shaft shall project from the housing for insertion in a conventional drill chuck.

Overall Length - 8 inches + or - 1/2 inch

Body Diameter - 5/8 inch plus or minus 1/8 inch

Bearings and Gears - The bearings and gears shall be properly sized and hardened to produce satisfactory operation of the tool.

Spindle - The spindle head shall be threaded to receive a collet chuck and/or drill adapter. Spindle offset shall be 1/4 inch maximum. Spindle thread shall be 10-32 NF-2B

Height of Head - 13/16 inch maximum

Drill Size Capacity - Drill size capacity shall be 3/16 inch

Accessories - A set of five (5) adapters of the set-screw type for plain shank drills shall be furnished with each attachment. The adapters shall properly mate with the angle drill attachment and shall be suitable for use with straight shank twist drills of the following sizes: 10, 20, 21, 30, and 40

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

11. 5130-00-533-0235 UI: BX

WHEEL, PEENING, ROTARY:

DESCRIPTION

Material: Steel

Width: 1.00"

Length: 2.00"

Box contains 5 each

In accordance with Minnesota Mining & Mfg. Part Number TC330-1x2 or equal

Offering on:

Manufacturer's Name: __________________________

Brand___________________________________

Model or Part No. __________________________________

See Technical Specifications paragraph(s): TB.1, T3.1, T4.1, T5.1 and T6.1.

12. 5130-00-542-3276 UI: EA

RIVETER, BLIND, PNEUMATIC:

DESCRIPTION

The riveter with required pulling heads, and carrying case shall meet the following requirements:

Air pressure consumption - 90 minimum to 120 psi maximum

Pulling capacity - 2250 pounds minimum at 90 psi Air Pressure.

Weight (less nose assembly) - 7 pounds maximum

Envelop dimensions - 14 x 6 x 6 inches maximum

Stroke - 1-1/8 inches minimum

Furnished with eight (8) pulling heads (one each for universal and countersunk head rivets to 1/8, 5/32, 3/16 and 1/4 inch diameter) and. one adapter.

Operation - With appropriate pulling head installed and operated in accordance with the manufacturers instructions, the riveters, shall be capable of properly pulling blind rivets conforming to MS20600 and MS20601.

Interchangeability: All repair and replacement parts for this model furnished shall be dimensionally and functionally interchangeable between different production lots. The riveter shall accommodate Cherry Rivet series H9040, Allfast RV3355 pulling heads or Gage Built Series 740 and shall be functionally capable with Cherry Rivet model G-740A, Allfast model RV30GD or Gage Built GBP740A model rivet guns.

Carrying case: Each riveter shall be furnished within a solid, rugged, compartmented carrying case with snap latch and handle.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

13. 5130-00-580-2305 UI: EA

RIVETER, BLIND, PNEUMATIC:

DESCRIPTION

Riveting Set, Capable of installing NAS 1919 and NAS 1921, 1/8, 5/32, and 3/16 inch mechanically locked spindle rivets when assembled with the appropriate nose assembly.

Item/Dimensions

Nose Assembly, 1/8 in.dia.

Nose Assembly, 5/32 in.dia.

Nose Assembly, 3/16 in.dia.

Anvil, Outer 1/8 in.dia.

Anvil, Outer 5/32 in.dia.

Anvil, Outer 3/16 in.dia.

Hex Key 5/32 in.

Hex Key 1/4 in.

Wrench, Box 7/16 in.

Nose Assembly Brush

Metal Carrying Case

Grip Gage, 1/8 & 5/32 in.

Grip Gage, 3/16 & 1/4 in.

All furnished in a metal case

Instruction Manual

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

14. 5130-00-596-0962 UI: EA

SHAVER, RIVET HEAD, PORTABLE, PNEUMATIC:

DESCRIPTION

Shaver, Rivet Head, Portable, Pneumatic

Type II - Single rotation shaver for soft metal rivets (aluminum, aluminum alloy, copper, brass, and mild steel); Class 1.

General Characteristics: W/Micrometer adjustment for depth of cut, graduated in increments of 0.0005 inches

Spindle data: Female Thd, 1/4-28, UNF

Cutter Data size: 5/16 in.; 3/8 in.; 7/16 in.; 1/2 in.

Footpiece Data size: 5/16 in.; 3/8 in.; 7/16 in.; 1/2 in.

With Carrying Case

See Technical Specifications paragraph(s): T1.2, T3.1, T4.2, T5.1 and T6.1.

15. 5130-00-596-9715 UI: EA

SAW, CIRCULAR, PORTABLE, ELECTRIC:

DESCRIPTION

This technical description covers a portable electric circular saw for use in an industrial or commercial environment.

The portable, electric saw described in this technical description is hand-guided and intended primarily for crosscutting and rip-sawing wood products at angles from 0 to 45 degrees. By use of special saw blades, ferrous and nonferrous metals, masonry, and ceramic materials may also be cut.

Salient Characteristics:

Design and construction - The saw shall be either double-insulated or of the 3-wire grounding construction.

Switch - A two-pole, single-throw, instant-release trigger switch shall be provided and mounted in the saw handle. The switch shall be provided with a guard to prevent accidental actuation. The switch shall not be equipped with a mechanism for locking in the "ON" position. Mechanism for locking in the "OFF" position is acceptable.

Electrical specifications - Unless otherwise specified, the motor for the saws shall be of the universal type designed to operate on either 120 volt (+,-10%) direct current (DC), or 120 volt (+,-6%), single-phase, 25-60 cycle alternating current (AC). The motor shall be mounted integral with the saw. The motor armature shall be balanced dynamically to insure freedom from destructive vibration.

Electromagnetic interference suppression - Not provided

Power cord and plug - The flexible cord shall be rated for use at a voltage not less than the rated voltage for the type motor as specified in the above Electrical specifications paragraph of this technical description. The saw shall be furnished with a wire supply cord with an integral ground. Unless otherwise specified the plug and cord shall have a minimum free length of 8 feet measured from point of entry into the saw.

Electric brake - The saw shall be provided with an electric brake feature to reduce coasting and stop blade in a maximum of two (2) seconds.

Saw Blades - Unless otherwise specified the saw shall be furnished with a carbide-tipped combination saw blade having 20 to 28 teeth.

The circular saw shall comply with the following design and performance requirements:

Motor armature axis at right angle to saw-blade spindle axis

Blade Diameter: 7-1/4 to 7-1/2 inches.

No-load Blade Speed: 4200 RPM minimum.

Cutting Capacity: 2-3/8 inches at 90 degrees (vertical).

Cutting Capacity: 1-3/4 inches at 45 degrees off vertical.

Power Output at Spindle: 3/4 minimum horsepower.

Rated Current: 9 amperes minimum.

Blade Arbor Hole Diameter: 5/8 inches.

Weight (Minus cord): 18 pounds maximum.

Accessories - The saw shall be supplied with such maintenance tools, accessories, attachments, extra parts, and complete operating and maintenance instructions as normally furnished commercially. One arbor nut wrench shall be included with each saw.

Carrying case - Each saw shall be supplied within a rigid, sturdy, impact resistant, plastic or metal carrying case of sufficient size and strength to contain the circular saw, maintenance tools and accessories. The case shall be complete with a hinged cover, carrying handles, and closing fastener.

Codes and Standards:

NEMA - Motors shall conform to National Electrical Manufacturers Association (NEMA) Publication No. MG-1.

UL. - All electrical components including motors, switches, and wiring shall conform to the applicable requirements of UL 45. The saw shall bear an identification plate in accordance with the applicable requirements of UL 45. Unless otherwise specified, the saw shall be furnished with an instruction manual in accordance with the applicable requirements of UL 45.

Regulatory Requirements:

Occupational Safety - Circular saws shall conform to Occupational Safety and Health Act (OSHA), 29 CFR 1910.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

16. 5130-00-760-1360 UI: EA

RIVETER, BLIND, PNEUMATIC:

DESCRIPTION

Capable of installing all 3/16, 1/4, 5/16 and 3/8 inch diameter.

Lockbolts in all materials;

Pull capacity - 9,400 lbs. min.

Stroke - 9/16 inch.

Operates on 90 to 120 psi of air

Weight - 17 lbs. max.

Overall height - 16 inch +/- 0.125 inch

Diameter of base - 7 inch +/- 0.060 inch

Length of head - 6 inch +/- 0.060 inch.

Huck Mfg. Co. Part Number - 246 or Cherry Div. of Textron Inc. Part Number G-87D or equal

Offering on:

Manufacturer's Name: __________________________

Brand___________________________________

Model or Part No. __________________________________

See Technical Specifications paragraph(s): TB.1, T3.1, T4.2, T5.1 and T6.1.

17. 5130-00-760-9677 UI: EA

INSTALLATION TOOL, FASTENER, HYDRAULIC:

DESCRIPTION

General Characteristics Item Description:

Function - All-purpose rivet gun used to install blind bolts and nuts up to 1/2 inch diameter

Handle Style - Pistol grip design

Type - straight drive type

Features - Three control buttons and operates on hydraulic pressure supplied by a Hi-Shear Corporation power unit Power Unit - Not Provided

Weight - 5.5 pounds maximum

HI-SHEAR Corp. part number BG2500 or equal

Offering on:

Manufacturer's Name: __________________________

Brand___________________________________

Model or Part No. __________________________________

See Technical Specifications paragraph(s): TB.1, T3.1, T4.2, T5.1 and T6.1.

18. 5130-00-770-6130 UI: EA

NOSE ASSEMBLY, FASTENER INSTALLATION:

DESCRIPTION

Type: Straight

Fastener Size: 1/4".

Feature: Non-Self Releasing

End use on Huck number 255, 256, and 353 pneumatic installing tool for C6L and GP fasteners.

Huck Manufacturing part number 99-2564. or equal

Offering on:

Manufacturer's Name: __________________________

Brand___________________________________

Model or Part No. __________________________________

See Technical Specifications paragraph(s): TB.1, T3.1, T4.2, T5.1 and T6.1.

19. 5130-00-772-7804 UI: EA

INTALLATION TOOL KIT

DESCRIPTION

Installation Tool Kit

Tool Kit Components:

Installation Tool (Power Riveter); Carrying Case; Wrenches (2 each); and Nose Assemblies (14 each).

Installation Tool (Power Riveter): A pneumatic-hydraulic tool designed for installation of a wide range of blind rivets, lock bolts and MAGNA-GRIP fasteners. Can be operated in any position with one hand.

Weight: 7.20 lbs.

Rivet Setting Stroke: .600"

Rated Pull Load: 6300 pounds

Noise Level: Less than 80 dB(A)

The Power Riveter operates on a wide range of air pressure, with 90 to 120 PSI providing the maximum efficiency. Air Inlet: Is provided with 1/4-18 female pipe threads, for accepting the user's air hose fitting.

Nose Assemblies Style Fasteners

3/16" Straight - Long NAS shear/tension

1/4" Straight - Long NAS shear/tension

1/4" Straight - Long

OSR-08

1/4"

Straight - Long

MS20600

5/16 Straight - Medium NAS shear/tension

5/16 Straight - Long NAS shear/tension

1/4" Straight - Medium NAS shear/tension

5/16" Straight - Medium BL-10

5/16" Straight - Medium BOM-R10

5/16" Straight - Long

OSR-10

3/8" Straight - Medium NAS shear/tension

3/8" Straight - Long NAS shear/tension

3/8" Straight- Medium OSR-12

3/8" Straight - Long

OSR-12

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

20. 5130-00-778-1675 UI: EA

RIVETER, BLIND, PNEUMATIC:

DESCRIPTION

This Technical Description covers a pneumatic riveting hammer and associated kit used for riveting in the aircraft industry and other assembly operations.

Design - The riveter shall be reliable and effective when operated with compressed air line pressures between 80 and 100 psig. During operation, the sound pressure level, when measured at an unobstructed distance of one meter, shall not exceed 95 dB(A). The air inlet connection shall consist of a well secured brass or ferrous fitting having an internally threaded 1/4 inch NPT.

Handle Style - Pistol Grip

Throttle - A nonleaking throttle shall be provided for controlling and regulating the air tool supply. The throttle shall be capable of varying the impact frequency of the riveter throughout the frequency range during operation. The throttle shall automatically and positively shut off the air supply when released

Air Volume Regulator - Included

Retainer - Included (e.g., beehive type)

The riveter shall comply with the following design and performance characteristics:

Rivet Maximum Diameter Accommodated - 0.250 inches for aluminum, dural, and soft iron cold rivets

Piston Stroke - 4 to 5-1/2 inches approximately

Piston Diameter - 1/2 to 9/16 inch approximately

Air Consumption - 16 scfm maximum

Impact Frequency - 1300 blows/min minimum. 1800 blows/min. maximum

Rivet set shank size - .401 inch

Pulling Head Attachment Characteristics:

1/8, 5/32, 3/16 inch lock spindle blind

1/8, 5/32, 3/16, 1.4 inch aluminum blind

1, 8, 5/32, 3/16 Huck oversize lock spindle

1/4 inch Huck oversize structural blind rivets

1/8, 5/32, 3/16 inch swaged fasteners

1/8, 5/32, 3/16 inch double action blind bolts

Accessory Components and Quantity:

Adapter, Anvil

Adapter, Nose

Kit, Service

Nut, Retaining

Reducer, Spindle

Sleeve, Shift

Stop, Retaining Nut

Tube, Pintail

Nose Assy, 3

Case, Metal, Holds 6 Nose Assemblies minimum

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

21. 5130-00-880-4586 UI: EA

GRINDER, DIE, PNEUMATIC, PORTABLE:

DESCRIPTION

Function - High speed die grinder designed for flash removal on small castings and plastic parts.

Drive End Type: Collet Chuck.

Size: 0.250 inches.

Handle Type: Straight.

Wheel Width Accommodated: 0.375 inches.

Wheel Diameter Accommodated: 1.000 inches.

Wheel Guard: Not Provided.

Safety Throttle: Not Included.

Extension Spindle: Not Provided.

Accessory Components and Quantity: Collet Wrench.

Special Features;

7/16 inch carbide burr.

3/4 inch mounted wheel capacity.

No-load speed: 40,000 RPM maximum (plus 0 minus 4000).

Throttle style: twist or lever.

Spindle type: 1/4 inch collet.

Weight: 1 pound maximum.

Overall Length: 6 inches maximum.

Rotary vane type motor.

Air consumption at no load: 17 SCFM maximum.

Spindle runout: 0.003 inch total indicator reading when measured 1/2 inch from the front end of collet. Horsepower: 0.13 minimum.

Air inlet: 1/8 inch NPT.

Spindle offset: 9/16 inch maximum.

Sound level: 85 dB(A) per the Compressed Air and Gas Institute's, "CAGI-PNEUROP Test Code for the Measurement of Sound from Pneumatic Equipment".

The grinder shall be furnished with operating and maintenance instructions, collet wrench(s), parts list and manufacturer's standard equipment.

See Technical Specifications paragraph(s): T3.1, T4.2, T5.1 and T6.1.

22. 5130-00-889-1841 UI: EA

HAMMER, PNEUMATIC, PORTABLE:

DESCRIPTION

This portable pneumatic hammer shall be furnished with chest in accordance with the requirements of paragraph 2.8 of Commercial Item Description A-A-52553 dated January 17, 1996

See Technical Specifications paragraph(s): T1.1, T3.1, T4.2, T5.1 and T6.1.

23. 5130-00-889-8985 UI: EA

HAMMER, PNEUMATIC, PORTABLE:

DESCRIPTION

This Technical Description covers pneumatic riveting hammers used for riveting in the aircraft industry and…