Attachment 7 National Stock Number Descriptions.pdf

ITEM PURCHASE DESCRIPTION

General Services Administration

1 | Page

ITEM PRODUCT DESCRIPTIONS - GUAM

(IPD)

Table of Contents

Section 1 Pages…. 2 -195 Office Supplies/Packaging Material 52 IPD

Section 2 Pages …196- 306 Janitorial/Sanitation/General Supplies 55 IPD

Section 3 Pages …… 307-345 Hardware/Maintenance Repair Operation Supply 40 IPD

Section 4 Pages..…346- 443 Furniture/Housewares

3 IPD

Section 5 Pages ...444-447 Ability One 205 NSN/IPD’s

2 | Page

3 | Page

5820-01-518-3622 UI: SE

RECEIVER-TRANSMITTER, RADIO

DESCRIPTION

ITEM NAME RADIO, RECEIVER-TRANSMITTER (WALKIE TALKIE),

FRS/GMRS

PRODUCT HEIGHT 7.00 INCHES (+/- 3.00 IN. (UNIT)

0.875 INCHES (+/- 0.25 IN.) (DISPLAY)

PRODUCT WIDTH 3.25 INCHES (+/- 1.00 IN.) (UNIT)

1.25 INCHES (+/- 0.2. IN) (DISPLAY)

PRODUCT DEPTH 1.75 INCHES (+/- 0.75 IN.)

BASIS WEIGHT 1.00 POUNDS MAXIMUM (UNIT)

4.00 POUNDS NOMINAL (SET)

DISPLAY TYPE LCD

DISPLAY LIGHTING BACKLIT

MIC AND HEADPHONE JACKS INCLUDED

FREQUENCY 462.550 ~ 467.7125 MHz WEATHER FREQUENCY 162.400 TO 163.275 MHz

NOAA WEATHER ALERT RADIO INCLUDED

WEATHER SCAN INCLUDED

RANGE 30 MILES OR BETTER

TRANSMIT POWER MAXIMUM ALLOWED BY LAW

CHANNEL QUANTITY 22 FRS AND GMRS (MINIMUM)

VOX LEVELS 5 MINIMUM

RoHS COMPLIANT YES

CERTIFICATION FCC CERTIFICATION PART 95

ALERTS VIBRATE ALERT

ROGER BEEP TO INDICATE CALL COMPLETION

AUDIBLE KEYSTROKE TONES

PRIVACY CODES 38 CTCSS, 104 DCS (142 MINIMUM, 3124 CHANNEL

OPTIONS)

SILENT OPERATION INCLUDED

CHANNEL SCAN INCLUDED

MONITORING FEATURE INCLUDED

DIRECT CALL FEATURE INCLUDED

AUTO SQUELCH INCLUDED

KEYPAD LOCK INCLUDED

POWER SUPPLY RECHARGEABLE BATTERIES (NiMH OR LITHIUM ION)

RECHARGEABLE BATTERIES INCLUDED

NONRECHARGEABLE BATTERIES NOT INCLUDED

TRANSMIT POWER SETTINGS HIGH AND LOW

CHARGER COMPATIBILITY DROP-IN CHARGER COMPATIBLE

4 | Page

INCLUDED IN SET ONE (1) PAIR OF RADIOS

BELT CLIPS

AC CHARGER / DC ADAPTER

RECHARGEABLE BATTERY PACKS

PAIR OF BOOM MIC HEADSETS

ENVIRONMENTAL PROCTECTION JIS4 WATER RESISTANCE (MINIMUM)

SPECIAL MARKINGS: In addition to normal commercial markings, each packaged set shall contain a label with the following text:

FRS Frequencies use: Federal government entities are authorized to purchase and operate radios certified by the FCC in the Family Radio Service (FRS), pursuant to Part 95 Subpart B of the FCC Rules and Regulations (Title 47, Code of Federal Regulations). Government users will be accorded the same privileges as non-federal users. Because FRS users must share each channel and no user is assured protection from interference caused by another authorized user, Federal entities may not purchase and operate FRS radios for planned communications operations that safeguard human life or property.

GMRS Frequencies use: Use of GMRS Frequencies requires an FCC license. It is the responsibility of the user to file for an appropriate FCC License. Per Title 47 CFR, Part 95 Subpart A Section 95.5, an individual is eligible to be licensed, but a non-individual (an entity other than an individual) is ineligible to obtain a GMRS license.

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

5 | Page

6645-00-250-4680 UI: EA

STOPWATCH

DESCRIPTION

ITEM NAME STOPWATCH

OVERALL DIAMETER SIZE 2.000 INCHES

OVERALL THICKNESS 0.500 INCHES

MINIMUM JEWEL QUANTITY 7

MAXIMUM BASIS WEIGHT 1 POUND

GRADUATION UNIT 1.000 MINUTE AND 0.200 (1/5) SECOND

TOTAL READER TIME 30 MINUTES

SCALE NAME MINUTE TOTALIZING AND SECONDS

SCALE QUANTITY 2

SCALE RANGE +0.00 / +30.00 MINUTE AND +0.00/ +60.00

SECOND

TOTALIZER DIAL RANGE +0.00 / +30.00 IN MINUTES

SWEEP HAND QUANTITY 1

MOVEMENT SIZE DESIGNATION 16

CASE MATERIAL ANY ACCEPTABLE

CASE SURFACE TREATMENT ANY ACCEPTABLE

JEWEL TYPE NATURAL OR SYNTHETIC SAPPHIRE, RUBY OR

GARNET

WATCH TYPE SINGLE ACTION

BEZEL TYPE ANY ACCEPTABLE

CRYSTAL TYPE ANY ACCEPTABLE

FACE TYPE OPEN POCKET

OVERALL BACKGROUND COLOR WHITE

OVERALL CRYSTAL COLOR CLEAR, UNCOLORED

INSCRIPTION COLOR ANY ACCEPTABLE

MAJOR GRADUATION COLOR ANY ACCEPTABLE

MINOR GRADUATION COLOR ANY ACCEPTABLE

DIAL BACKGROUND COLOR WHITE ENAMEL

DIAL NUMERAL COLOR BLACK

DIAL SCALE MARKING COLOR ANY ACCEPTABLE

DIAL SCALE MARKING LUMINOSITY NON-LUMINOUS

SEPARATE TOTALIZER DIAL INCLUDED

WINDING METHOD STEM

STEM OPERATION CONSECUTIVE CROWN DEPRESSIONS FOR

STOP, START AND RETURN TO ZERO

MOVEMENT TYPE CONTINUOUS RUNNING

NON-MAGNETIC CHARACTERISTIC INCLUDED

ESCAPEMENT TYPE ANY ACCEPTABLE

SUBMERSIBILITY NON-SUBMERSIBLE

SHOCKPROOF FEATURE INCLUDED

WATER RESISTANT FEATURE INCLUDED

STRIKING MECHANISM NOT INCLUDED

CIVIL DATE INDICATOR NOT INCLUDED

6 | Page

LUMINOUS DIAL NOT INCLUDED

LUMINOUS HAND NOT INCLUDED

LUMINOUS NUMERAL NOT INCLUDED

SPECIAL FEATURE USED FOR LABORATORIES AND GEOLOGICAL SURVEYS

IN AREAS OF HIGH HUMIDITY AND DUST

ENVIRONMENTAL PROTECTION DUST, WATER, ANIT-MAGNETIC, SHOCK, CORROSION AND

EROSION RESISTANT CAUSED BY ACIDS

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight

7 | Page consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7045-01-477-7792 UI: EA

PAD, MOUSE

DESCRIPTION

ITEM NAME PAD, MOUSE

OVERALL WIDTH 10.00 INCHES (+/- 1.00 INCH)

OVERALL LENGTH 12.00 INCHES (+/- 1.00 INCH)

OVERALL HEIGHT 1.500 INCHES (+/- 0.25 INCH)

BASIS WEIGHT 1.200 LBS

OVERALL COLOR BLACK

COVER MATERIAL LYCRA

CUSHIONING MATERIAL GEL FILLED

SPECIAL FEATURES PATENTED MECHANISM ALLOWS THE GEL WRIST

REST TO GLIDE FREELY AT THE BASE OF THE

MOUSE PAD. PROVIDES AN OPTICAL FRIENDLY

MOUSE TRACKING SURFACE; DURABLE

AND ERGONOMIC

ENVIRONMENTAL PROTECTION STAIN RESISTANT

8 | Page

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R_151007.pdf

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA

PCM

9 | Page

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: THE GEL WRIST REST SHALL BE UNIFORMLY CONSTRUCTED IN ACCORDANCE

WITH GOOD COMMERCIAL PRACTICE AND BE FREE FROM DEFECTS WHICH MAY IMPAIR THE

UTILITY OF THE PRODUCT FOR THE INTENDED USE. THE GEL WRIST REST SURFACE SHALL BE

DURABLE, SMOOTH, UNIFORM AND BE FILLED WITH A STABLE GEL MATERIAL THAT IS

COMMERCIALLY USED IN SIMILAR OFFICE PRODUCTS. THE GEL WRIST REST SHALL BE

CONSTRUCTED TO PREVENT LEAKAGE OF ANY OF THE FILLING MATERIAL DURING THE USEFUL

LIFE OF THE ITEM.

7045-01-515-6774 UI: PG

DISK, NONFLEXIBLE

DESCRIPTION

ITEM NAME DISK, NONFLEXIBLE (CD-RW)

OVERALL DISK DIAMETER 4.750 INCHES

RECORDING SURFACE COLOR SILVER

RECORDING DATA CAPACITY 700MB (DATA)

RECORDING TIME CAPACITY 80 MINUTES (AUDIO)

RECORDING SPEED 1X MINIMUM TO 4X MAXIMUM

REWRITABILITY UP TO 1,000 TIMES

MEDIA STORAGE CAPABILITY AUDIO, VIDEO, DIGITAL PICTURES AND DATA

SIDE TYPE SINGLE

UNIT PACKAGE FORM SPINDLE

UNIT PACKAGE QUANTITY 25 DISKS PER SPINDLE

10 | Page

PACKAGING/PACKING: Twenty-five (25) nonflexible disks shall be packaged on a spindle in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R_151007.pdf

Marking: Each individual recordable DVD/CD shall be permanently marked on the non-recordable side with a manufacturer's brand name; media type; storage and time capacity; recording speed, in accordance with industry standard.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

11 | Page

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7105-00-782-3166 UI: EA

STOOL, STEP

DESCRIPTION

ITEM NAME STOOL, STEP

I.A.W. A-A-3014

FED-STD-595

OVERALL HEIGHT 13.00 INCHES

OVERALL DEPTH 16.00 INCHES

MAXIMUM WEIGHT CAPACITY 350 POUNDS

OVERALL COLOR BLACK FRAME

OVERALL MATERIAL PLASTIC OR STEEL FRAME

SURFACE TREATMENT ENAMEL FRAME

BASE TYPE FLAT

DUTY TYPE HEAVY DUTY

BASE END TYPE SWIVEL CASTERS

SPECIAL FEATURES STEP STOOL GLIDES EASILY ON RETRACTABLE CASTERS

packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the

12 | Page

National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

13 | Page

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7490-01-504-5605 UI: EA

SHREDDING MACHINE, PAPER:

DESCRIPTION

ITEM NAME SHREDDING MACHINE, PAPER

OVERALL WIDTH 20.00 IN. (ALL DIMENSIONS +/- 10 PERCENT)

OVERALL HEIGHT 34.00 IN. (ALL DIMENSIONS +/- 10 PERCENT)

OVERALL DEPTH 17.00 IN. (ALL DIMENSIONS +/- 10 PERCENT)

OVERALL THROAT OPENING WIDTH 10.75 INCHES (+/- 0.50 INCHES) TOP FEED

MAXIMUM WEIGHT 175 POUNDS

SECURITY LEVEL HIGH - LEVEL 6 I.A.W. NSA/CSS SPECIFICATION

02-01 ONE HOUR NSA DURABILITY TEST 15 REAMS WHEN FEEDING 7 SHEETS (or better)

DUTY TYPE HEAVY, HIGH VOLUME

SHREDDING TYPE CROSS CUT

SHRED SIZE 0.80 MM X 5.00 MM (+2 PERCENT, -20

PERCENT)

OVERALL SHRED SPEED 23 FT/MIN

POWER RATING 1.75 HP

POWER SOURCE 115 VOLTS, 60HZ AC POWER

MINIMUM CONTAINER VOLUME 24 GALLONS

SHEET CAPACITY UP TO 13 SHEETS/PASS

BIN MATERIAL PLASTIC OR WOOD OR METAL

AUTOMATIC OILER INCLUDED; FACTORY INSTALLED

AUTOMATIC OILER CAPACITY 0.50 GALLON (MINIMUM FOR EXTERNAL

CONTAINER) OR 0.50LITER (MINIMUM FOR

INTERNAL RESEVOIR)

START/STOP CONTROL TYPE AUTOMATIC

FULL BAG DESIGN DOOR WILL OPEN AND MACHINE WILL SHUT

OFF

CUTTING ROLLER MATERIAL HARDENED STEEL

14 | Page

CUTTING HEAD MATERIAL HARDENED SOLID STEEL

SHREDDED MATERIAL LOCATION KEPT IN AN ENCLOSED SECTION OF SHREDDER

AND CAN BE EASILY REMOVED FOR DISPOSAL

ONE HOUR NSA DURABILITY TEST 15 REAMS WHEN FEEDING 7 SHEETS (OR

BETTER)

SPECIAL FEATURE THERMALLY PROTECTED MOTOR TO PREVENT

OVERHEATING; USE AND SAFETY PROTECTION

SYSTEM

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

IN ACCORDANCE WITH BELOW PALLETIZATION REQUIREMENT, DATED 8/15/2004, UNLESS

OTHERWISE INDICATED IN THE CONTRACT OR PURCHASE ORDER.

PALLETIZATION REQUIREMENT 8/15/2004

Palletization: The shipping (transport) containers shall be palletized. The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, and double-face non-reversible pallets. The palletized load shall not exceed 2500 pounds in weight for shipments to the Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (French Camp and Stockton Locations). The palletized load shall not overhang the pallet deck board edge by more than 1 inch and shall not exceed 53 inches in overall height (including pallet). Less than half pallet loads or loads shipped by small package carrier in acceptable transport packing need not be palletized. When less than full but more than a half pallet is used, the palletized load shall utilize proper bracing and/or reinforcement to ensure that the load can withstand two additional loads placed on it.

15 | Page

Stacking: A load-stacking test shall be performed once, at the beginning of the contract, for each different unitized or palletized load configuration. A fully palletized load shall be tested utilizing a total stack of three palletized loads, with all the proper bracing and/or reinforcement necessary to perform the test. There shall be no evidence of damage to the pallets, shipping containers or products when stack is tested on the rigid surface for a minimum of 24 hours, in compliance with all the National and Local Safety Regulations. The pre-tested palletized load configuration shall be duplicated using the same packaging materials, pattern, number of shipping (transport) containers, and procedures consistent throughout the duration of the contract.

Palletized loads shall be stable and safe when handled with mechanical equipment by qualified personnel.

Materials: All lumber used inside or outside a shipment shall be bark free. No used wood pallets with repaired components or stringers will be acceptable. All wood pallet stringers shall be manufactured from hardwoods.

Pallets manufactured of materials other than wood, shall conform to all the requirements specified herein.

Unitization: For the purpose of this requirement, the assembled group of containers or items in a single load that can be handled as a unit throughout the distribution system. Unitization encompasses, but is not limited to, consolidation in a container, placement on a pallet or load base having forklift capability, or securely binding together. Shipments should be considered for unitization where appropriate or specified.

Unitization of pallet load: The palletized load shall be unitized and secured to the pallet to insure that the load arrives intact without product damage. The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Vertical, horizontal or filler reinforcement shall be added as necessary to meet the stacking strength requirements. A palletized load shall be secured to the pallet by shrink or stretch wrapping, and/or, by steel or nonmetallic strapping. When steel or nonmetallic strapping is used, edge protectors shall be provided to prevent damage to the cartons when tensioning the strapping. As a minimum, two straps shall run lengthwise, two straps shall run widthwise, and two straps shall run around the girth of the palletized load.

A palletized load shall be capable of protecting the products against damage in a multiple handling, transportation, and storage environment having distribution warehouses with rack systems that support the load/s overhead of warehouse personnel.

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

Regulatory Requirements: The offerer/contractor is encouraged to provide energy-efficient products to the maximum extent practicable in accordance with paragraph 23.203 of the Federal Acquisition Regulations

(FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter

QUALITY ASSURANCE

16 | Page

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7510-00-165-6560 UI: RO

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

ITEM NAME TAPE, PRESSURE SENSITIVE ADHESIVE

OVERALL WIDTH 1.250 INCHES

OVERALL LENGTH 36.00 YARDS

OVERALL CORE DIAMETER 3.000 INCHES

UNIT TYPE FOAM TAPE

UNIT DESIGN DOUBLE-SIDED

USAGE DESIGN FOR THERMAL INSULATION, GASKETING,

SEALING, JOINING, REDUCING SHOCK AND VIBRATION

USAGE FORM ROLL

OVERALL COLOR BLACK

OVERALL MATERIAL PLASTIC, VINYL

MATERIAL TRANSPARENCY OPAQUE

SURFACE LUSTER LUSTERLESS

ADHESIVE LOCATION BOTH SIDES

LINER INCLUDED

LINER TYPE SILICONE-TREATED

ENVIRONMENTAL PROTECTION WEATHER RESISTANT AND SOLVENT RESISTANT

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

SHELF LIFE

17 | Page

ITEM: Tapes, Pressure Sensitive, Adhesive Type II: Extendable Age on Delivery: 2 Months Shelf Life Code: 4 (12 Months Extendable Shelf Life)

Tapes shall be delivered within two (2) months after the date of manufacture and have a shelf life of twelve

(12) months after the date of manufacture. After twelve (12) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R_151007.pdf

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA

18 | Page

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7510-00-266-6715 UI: RO

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

IN ACCORDANCE WITH ASTM D 5486 - STANDARD SPECIFICATION FOR PRESSURE-SENSITIVE

TAPE FOR PACKAGING, BOX CLOSURE, AND SEALING.

ITEM NAME TAPE, PRESSURE SENSITIVE ADHESIVE

I.A.W. TYPE: I

CLASS: 2

OVERALL WIDTH 2.000 INCHES

OVERALL LENGTH 60.00 YARDS

OVERALL CORE DIAMETER 3.000 INCHES

OVERALL THICKNESS 0.003 INCHES

UNIT TYPE SEALING TAPE

19 | Page

USAGE FORM ROLL

OVERALL COLOR COLORLESS

MATERIAL TRANSPARENCY CLEAR

ADHESIVE LOCATION ONE SIDE

TEMPERATURE RATING NOT RATED

PACKAGING/PACKING

PACKAGING/PACKING: Each roll shall be individually packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not exceed 51 pounds in weight.

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive Type II: Extendable Age on Delivery: 3 Months Shelf Life Code: 5 (18 Months Extendable Shelf Life)

Tapes shall be delivered within three (3) months after the manufacture date, and have a shelf life of eighteen

(18) months after the manufacture date. After eighteen (18) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

20 | Page

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

21 | Page

7510-00-551-9825 UI: RO

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

In accordance with A-A-113D, Dated December 4, 1996: Commercial Item Description covers transparent and colored pressure-sensitive adhesive tape which is intended for temporary mending and attaching, temporary identification, charting and decorating.

ITEM NAME TAPE, PRESSURE SENSITIVE ADHESIVE

I.A.W. TYPE: II - MATTE FINISH

CLASS: A - TRANSPARENT CELLULOSE ACETATE OR

POLYOLEFIN BACKING

OVERALL WIDTH 0.750 INCHES

OVERALL LENGTH 36.00 YARDS

OVERALL CORE DIAMETER 1.000 INCHES

OVERALL THICKNESS 0.002 INCHES

USAGE FORM ROLL

OVERALL COLOR COLORLESS

OVERALL MATERIAL PLASTIC

MATERIAL TRANSPARENCY CLEAR

SURFACE LUSTER MATTE

ADHESIVE TYPE ACRYLIC

ADHESIVE LOCATION ONE SIDE

DISPENSER NOT INCLUDED

SPECIAL FEATURE CAN BE WRITTEN ON WITH PEN, PENCIL OR MARKER

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive Type II: Extendable Age on Delivery: 2 Months Shelf Life Code: 4 (12 Months Extendable Shelf Life)

22 | Page

Tapes shall be delivered within two (2) months after the date of manufacture and have a shelf life of twelve

(12) months after the date of manufacture. After twelve (12) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

23 | Page

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7510-01-318-6591 UI: BX

PROTECTOR, DOCUMENT

DESCRIPTION

ITEM NAME PROTECTOR, DOCUMENT

OVERALL WIDTH 9.000 INCHES

OVERALL LENGTH 11.00 INCHES

ACCOMMODATED SHEET WIDTH 8.500 INCHES

ACCOMMODATED SHEET LENGTH 11.00 INCHES

OVERALL THICKNESS 0.002 INCHES

OVERALL COLOR CLEAR

OVERALL MATERIAL PLASTIC, POLYPROPYLENE

MATERIAL TRANSPARENCY TRANSPARENT

SURFACE CONDITION POLISHED

LOAD LOCATION TOP

WEIGHT TYPE STANDARD

TAB COLOR ASSORTED - RED, YELLOW, GREEN, BLUE,

AND WHITE

TAB CUT TYPE STRAIGHT CUT EDGE

TAB CUT SIZE 1/5

TAB CUT POSITION STAGGERED POSITION PER COLOR

HOLE WIDTH 0.250 INCH (+/-0.031 INCH) FOR OBLONGHOLE

HOLE LENGTH 0.375 INCH (+ 0.062 INCH) FOR OBLONG HOLE

HOLE DIAMETER SIZE 0.250 INCH (+/-0.031 INCH) FOR ROUND HOLE

HOLE DISTANCE 4.250 INCHES CENTER TO CENTER

HOLE SHAPE ROUND OR OBLONG

24 | Page

HOLE QUANTITY 7

HOLE LOCATION 11.00 INCH SIDE

UNIT TYPE COLORED INDEX SHEET PROTECTOR

UNIT DESIGN FIT VARIETY OF BINDERS INCLUDING SEVEN-

RING BINDER

USAGE DESIGN SEPARATING DOCUMENTS BY CATEGORY,

INDEXING DOCUMENT OR ORGANIZING

PRESENTATION

PAPER INSERT NOT INCLUDED

SPECIAL FEATURE FLEXIBLE PLASTIC SHEET WHICH IS FORMED TO

A DOUBLE THICKNESS OF THE SIZE SPECIFIED

UNIT PACKAGE QUANTITY 20 OF EACH COLOR (5 COLORS TOTAL)

UNIT QUANTITY PACKAGING 100 DOCUMENT PROTECTORS PER BOX

PACKAGING/PACKING: One hundred (100) document protectors shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations

- In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007.

Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity.

The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA

25 | Page

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7510-01-347-9579 UI: BX

PROTECTOR, DOCUMENT

DESCRIPTION

ITEM NAME PROTECTOR, DOCUMENT

OVERALL WIDTH 8.500 INCHES

OVERALL LENGTH 11.00 INCHES

ACCOMMODATED SHEET WIDTH 8.500 INCHES

ACCOMMODATED SHEET LENGTH 11.00 INCHES

OVERALL THICKNESS 0.003 INCHES

OVERAL…