47QMCA20R0002 Amendment 3.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES

1 5

2. AMENDMENT/MODIFICATION NO.

3. EFFECTIVE DATE

SEPT 11, 2020

4. REQUISITION/PURCHASE REQ. NO.

5. PROJECT NO. (IF APPLICABLE)

6. Issued By Code QMAAA 7. ADMINISTERED BY (If other than Code

U. S. GENERAL SERVICES ADMINISTRATION

FEDERAL ACQUISITION SERVICE

OFFICE OF TRAVEL, TRANSPORTATION & LOGISTICS

LIGHT DUTY AUTOMOTIVE ACQUISITION SUPPORT DIV

1800 F ST, NW HUB 3200

WASHINGTON, DC 20405

8. Name and Address of Contractor (No., street, county, State and ZIP Code

X

9A. AMENDMENT OF SOLICITATION NO.

47QMCA20R0002

9B. DATED (SEE ITEM 11)

MAY 28, 2020

10A. MODIFICATION OF CONTRACT/ORDER NO.

10B. DATED (SEE ITEM 13)

CODE FACILITY CODE

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in item 14. The hour and date specified for receipt of

Offers is extended X is not extended.

Offer's must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

(a) By completing Items 8 and 15, and returning ___1____copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGEMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS,

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER NO. IN

ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

2020 MAIN BUS PROGRAM

Solicitation Changes: Note the changes that have been made to AutoStandards based on updates to Federal Standard 833P.

The point of contact for this amendment is Craig D. Yokum, craig.yokum@gsa.gov, 703-605-9291.

Except as provided herein, all terms and conditions of the solicitation referenced in item 9A, as heretofore changed, remain unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print) 16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

Craig D. Yokum Contracting Officer

15B. CONTRACTOR/OFFEROR 15C. DATE 16B. UNITED STATES OF AMERICA 16C. DATE SIGNED

BY ______________________________________________

(Signature of person authorized to sign) (Signature of Contracting Officer)

NSN 7540-01-152-8070 30-105 STANDARD FORM 30 (REV. 10-83)

PREVIOUS EDITION UNUSABLE Prescribed by GSA, Reproduced by FSS

FAR (48 CFR) 53.243

Solicitation 47QMCA20R0002 Amendment 3 Page 2 of 5

RETURN THE SF30 COVER PAGE ONLY OF AMENDMENT 3

WITH BLOCKS 8, 15A, 15B, AND 15C COMPLETED BY SEPT 18,

2020.

Updates to Solicitation 47QMCA20R0002

The following Federal Standard 833P files were updated on July 27, 2020 and notification was made via Amendment 2 on August 17, 2020

833P Bus Options Appendix A Specifications

Fed Std 833P Item 202C Type A School Bus Basic

Fed Std 833P Item 398 Heavy Duty Over the Road Touring Coach

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor

Fed Std 833P Items 241N-247 Light Duty Shuttle Basic

Fed Std 833P Items 301C-304C Type A School Bus

Fed Std 833P Items 341N-347 Light Duty Shuttle Bus

Fed Std 833P Items 359W-363W Medium Duty Shuttle Bus

Fed Std 833P Items 396-397 Heavy Duty Intercity Commuter Coach

[Those Fed Std 833P files without changes are not included here, but are still effective.]

The AutoStandards and Models that were impacted by these changes are indicated below:

Solicitation 47QMCA20R0002 Amendment 3 Page 3 of 5

Fed Std 833P

Amendment 3 Changes Summary – July 27, 2020

Changes to Standards:

1. SIN 202C Type A School Bus Basic

a. 3.8.3 Batteries ‐ Hood‐mounted OEM batteries acceptable

2. SINs 301C‐304C Type A School Bus

a. 3.8.3 Batteries ‐ Hood‐mounted OEM batteries acceptable

3. SIN 240L Light Duty Shuttle Low‐Floor

a. 3.7.2 Driveshaft – Driveshaft standards are only applicable to FWD vehicles

b. 3.14.4 Driver’s Area – Telescoping steering wheels allowed

4. SINs 241N‐247 Light Duty Shuttle Basic

a. 3.1.2 Body Construction ‐ The body shall have a metal cage‐type frame with welded joints. The frame itself shall not be held together by rivets or adhesives.

b. 3.1.7 Body Exterior Width – Overall width measurements indicated in

AutoStandards shall be from the outermost body surfaces. Flared wheel wells do not count as a body surface for the purposes of this measurement.

c. 3.4 Engine Accessories – Removed requirement for high idle control

d. 3.8.3 Batteries ‐ Hood‐mounted OEM batteries acceptable

e. 3.14.3 Stowage Compartment – Not required for narrow body SINs (241N

& 242N)

f. 3.14.4 Driver’s Area – New driver’s area requirements:

i. Shall comply with FMCSR 393.51

ii. All switches and controls shall be marked with easily read identifiers

iii. Ignition switch

iv. Push button start is acceptable if the power supply to the switch is controlled by a keyed switch or electronic recognition.

v. Tilt steering wheel/column

vi. Engine coolant temperature overheat warning

vii. Engine low oil pressure indication

viii. Fuel level indicating gauge

ix. Transmission selector

Solicitation 47QMCA20R0002 Amendment 3 Page 4 of 5

5. SINs 341N‐347 Light Duty Shuttle Bus

a. 3.1.2 Body Construction ‐ The body shall have a metal cage‐type frame with welded joints. The frame itself shall not be held together by rivets or adhesives.

b. 3.1.7 Body Exterior Width – Overall width measurements indicated in

AutoStandards shall be from the outermost body surfaces. Flared wheel wells do not count as a body surface for the purposes of this measurement.

c. 3.4 Engine Accessories – Removed requirement for high idle control and coolant heater

d. 3.8.3 Batteries ‐ Hood‐mounted OEM batteries acceptable

e. 3.10.4 Stowage Compartment – Not required for narrow body SINs (341N

& 342N)

f. 3.13.1 Radio/PA System ‐ The PA system does not need to be integrated into the factory radio, however it should still use the primary speakers

6. SINs 359W‐363W Medium Duty Shuttle Bus

a. 3.18.1 Driver’s Seat – Added exception to standard: If the OEM does not allow the replacement of OEM seats due to safety reasons, the driver’s seat does not need to meet all the specifications in this section. During the first article inspection, we will require documentation from the OEM which supports your claim. The features that are missing from the seat will also need to be indicated on the clarifications tab.

7. SINs 396‐397 Heavy Duty Intercity Commuter Coach

a. 3.6.2 Air Brakes – Air tanks allowed to have ¼‐turn ball valve drain or spring‐loaded manual pull valve

b. 3.8.1 Electrical System ‐ Wiring shall be routed in conduit or high temperature looms with a rating of 300°F in areas exposed to high temperatures (i.e. engine compartment)

c. 3.8.3 Batteries – Spliced cables now allowed in certain areas

d. 3.14.5 Interior Mirror – Minimum area changed to 57 square inches

8. SIN 398 Heavy Duty Over the Road Touring Coach

a. 3.1.11 Insulation ‐ Insulation shall fill cavities between bows

b. 3.6.2 Air Brakes – Air tanks allowed to have ¼‐turn ball valve drain or spring‐loaded manual pull valve

c. 3.8.1 Electrical System ‐ Wiring shall be routed in conduit or high temperature looms with a rating of 300°F in areas exposed to high temperatures (i.e. engine compartment)

d. 3.8.3 Batteries – Spliced cables now allowed in certain areas

e. 3.14.5 Interior Mirror – Minimum area changed to 57 square inches

f. 3.15.1 Floor Construction – Removed requirement for epoxy paint seal

Solicitation 47QMCA20R0002 Amendment 3 Page 5 of 5

g. 3.15.6 Lavatory ‐ Manufacturer’s standard forced ventilation enclosure and towelette or waterless gel dispenser for hand sanitizing.

9. Appendix A – Options Specifications

a. Renewed outdated formatting to match the style of the other standards

b. Addition of Table of Options

c. BFST– BARRIER–FULL HEIGHT–TRANSLUCENT ‐ The barrier may be partially padded, but only up to the height where it has no effect on the driver’s visibility or protection.

d. New Option: CLV – CEILING – LIGHT – VINYL ‐ Requires ceiling to be covered with medium gray or white vinyl.

e. FFP – HEATER–COOLANT–FUEL FIRED ‐ The minimum specification varies based on the standard fuel for the SIN:

i. SINs with GAS standard: Minimum 17k BTU

ii. SINs with DIESEL standard: Minimum 40k BTU

f. FSS– FIRE SUPPRESSION SYSTEM ‐ The fire detector(s) shall be optical infrared (IR), thermally operated linear (LTD) type, or spot type thermal sensor.

g. HDAC – HEAVY DUTY AIR CONDITIONING ‐ Espar AC350 Integrated Roof

Top air conditioner requirement changed to model AC33. Bitzer 4NFCY compressor allowed in addition to Bock FK40‐655K.

h. RM6– MIRRORS–EXTERIOR REARVIEW HEATED REMOTE – Removed requirement for pictograms

i. SICS– SEAT–CHILD SEAT–INTEGRATED–SCHOOL BUS ‐ HSM NextGen with

Child Restraints Seat allowed

j. New Option: WPPO– WINDOW–PASSENGER–PUSH OUT ‐ Requires manufacturer’s largest available push out windows to replace the standard equipment windows. The window glass shall be tinted and tempered or tinted and laminated safety glass.

Changes to Models:

1. 241.5, 341.5 ‐ SENATOR ‐ GVWR Changed to 14500, Rear axle 9600

2. 321A.1, 322A.1, 336A.1, 338A.1 – CE – Driver’s seat changed to “National”

3. 341.1 – ADVANTAGE – Side Panels changed to “Padded‐Woven Fabric, Medium

Gray”, Ceiling changed to “Padded‐Woven Fabric, Medium Gray”

4. 240L.1 – FRNTRUNNER – Body Size (Length) changed to 173 inches