36E77619R0086-018.pdf

ELECTRONIC SAFETY AND SECURITY SYMBOLS

ELECTRONIC SAFETY AND SECURITY ABBREVIATIONS

CR

RX

EL

SECURITY CAMERA SUBSCRIPT LEGEND

POI POINT OF INTERFACE

POTS PLAIN OLD TELEPHONE SERVICE

PR PAIR

PVC POLYVINYL CHLORIDE

SE SERVICE ENTRANCE

SP SERVICE PROVIDER

SPC STORED PROGRAM CONTROL

SPD SURGE PROTECTION DEVICE

SPG SINGLE-POINT GROUND

STA STATION

STP SHIELDED TWISTED PAIR

SW STATION WIRE

SYS SYSTEM

TBBC TELECOMMUNICATIONS BACKBONE BONDING CONDUCTOR

TBC TELECOMMUNICATION BONDING CONDUCTOR

TC TELECOMMUNICATIONS CLOSET

TEL TELEPHONE

TELCO TELEPHONE COMPANY

TERM TERMINAL

TGB TELECOMMUNICATIONS GROUNDING BUSBAR

THD TOTAL HARMONIC DISTORTION

TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION

TMGB TELECOMMUNICATIONS MAIN GROUNDING BUSBAR

TO TELECOMMUNICATIONS OUTLET

TPDDI TWISTED PAIR DISTRIBUTED DATA INTERFACE

TPPMD TWISTED PAIR PHYSICAL MEDIA DEPENDENT

TR TELECOMMUNICATIONS ROOM

TT TELEPHONE TERMINAL

TTB TELEPHONE TERMINAL BOARD

TTY TEXT TELEPHONES

TVSS TRANSCEINT VOLTAGE SURGE SUPPRESSOR

TYP TYPICAL

UG UNDERGROUND

UL UNDERWRITERS LABORATORIES

UPS UNINTERRUPTIBLE POWER SUPPLY

UTP UNSHIELDED TWISTED PAIR

ISDN INTEGRATED SERVICES DIGITAL NETWORK

ISO INTEGRATED STANDARDS ORGANIZARION

IW INSIDE WIRING (CABLE)

KHz KILOHERTZ

KTS KEY TELEPHONE SYSTEM

LAN LOCAL AREA NETWORK

LASER LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION

LATA LOCAL ACCESS TRANSPORT AREA

LBO LINE BUILDOUT

LEC LOCAL EXCHANGE CARRIER

LED LIGHT EMITTING DIODE

LOCAP LOW CAPACITANCE

MAX MAXIMUM

MC MAIN CROSS-CONNECT

MDF MAIN DISTRIBUTION FRAME

M/G MOTOR/GENERATOR SET

MH MAINTENANCE HOLE

MICRON MICROMETER

MIN MINIMUM

MISC MISCELLANEOUS

MODEM MODULATOR/DEMODULATOR

NEC NATIONAL ELECTRIC CODE

NESC NATIONAL ELECTRIC SAFETY CODE

NIC NOT IN CONTRACT

NID NETWORK INTERFACE DEVICE

NIU NETWORK INTERFACE UNIT

NRTL NATIONALLY RECOGNIZED TESTING LABORATORY

NTS NOT TO SCALE

OC ON CENTER

OD OUTSIDE DIAMETER

OFNP OPTICAL FIBER NON-CONDUCTIVE PLENUM

OFNR OPTICAL FIBER NON-CONDUCTIVE RISER

OPD OVERCURRENT PROTECTION DEVICE

OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION

OSP OUTSIDE PLANT

PAM PULSE AMPLITUDE MODULATE

PB PULL BOX

PBX PRIVATE BRANCH EXCHANGE

PCM PULSE CODE MODULATION

PIC POLYETHYLENE INSULATED CONDUCTOR

D/A DIGITAL TO ANALOG CONVERSION

DAF DEDICATED ACCESS FACILITY

DB DECIBEL

DC DIRECTED CURRENT

DD DISTRIBUTION DESIGNER

DEMARC DEMARCATION POINT

DW DISTRIBUTION WIRE

DWG DRAWING(S)

EBC EQUIPMENT BONDING CONDUCTOR

EC ELECTRICAL CONTRACTOR

EF ENTRANCE FACILITY

EIA ELECTRONICS INDUSTRY ASSOCIATION

ELEC ELECTRICAL

EMC ELECTROMAGNETIC COMPATABILITY

EMI ELECTROMAGNETIC INTERFACE

EMT ELECTRICAL METALLIC TUBING

EXT EXTENSION

FCC FEDERAL COMMUNICATIONS COMMISSION

FD FLOOR DISTRIBUTION

FDDI FIBER DISTRIBUTION DATA INTERFACE

FDM FREQUENCY DIVISION MULTIPLEXING

FDR FEEDER

FO FIBER OPTIC

FOTP FIBER OPTIC TRANSMISSION SYSTEM

FREQ FREQUENCY

FTP FOIL TWISTED PAIR

GA GAUGE

GEC GROUNDING ELECTRIC CONDUCTOR

GHz GIGAHERTZ

GND GROUND

HC HORIZONTAL CROSS-CONNECT

HF HIGH FREQUENCY

HH HANDHOLE

HVAC HEATING, VENTILATION AND AIR CONDITIONING

Hz HERTZ

IC INTERMEDIATE CROSS-CONNECT

ICEA INSULATED CABLE ENGINEERS ASSOCIATION

IDC INSULATION DISPLACEMENT CONNECTION

IDF INTERMEDIATE DISTRIBUTION FRAME

IEEE INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS

8P8C 8-POSITION, 8-CONDUCTOR

AC ALTERNATING CURRENT

A/D ANALOG TO DIGITAL CONVERSION

ADA AMERICANS WITH DISABILITIES ACT

AER AERIAL

AFF ABOVE FINISHED FLOOR

AIA AMERICAN INSTITUTE OF ARCHITECTS

AM AMPLITUDE MODULATION

ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

ARMM PIC RISER, EXPANDED POLYETHYLENE PVC, 24 AWG, ALVYN

ASCII AMERICAN STANDARD CODE FOR INFORMATION INTERCHANGE

ATM ASYNCHRONOUS TRANSFER MODE

AWG AMERICAN WIRE GAUGE

BD BUILDING DISTRIBUTOR

BDF BUILDING DISTRIBUTION FRAME

BEF BUILDING ENTRANCE FACILITY

BER BIT ERROR RATE

BIC BUILDING INDUSTRY CONSULTANT

BICSI BUILDING INDUSTRY CONSULTING SERVICES

BRISDN BASIC RATE INTEGRATED SERVICES DIGITAL NETWORK

BTU BRITISH THERMAL UNIT

CATV CABLE TELEVISION

CBC COUPLED BONDING CONDUCTOR

CC COMMUNICATIONS CONTRACTOR

C CONDUIT

CER COMPUTER EQUIPMENT ROOM

CIRC CIRCUIT

CFC COMMUNICATIONS FLAT CABLE

CLO CLOSET

CO CENTRAL OFFICE

CODEC CODER/DECODER

COE CENTRAL OFFICE EQUIPMENT

COT CENTRAL OFFICE TERMINAL

CPC CUSTOMER PREMISES COMMUNICATIONS

CPE CUSTOMER PREMISES EQUIPMENT

CPU CENTRAL PROCESSING UNIT

CSA CANADIAN STANDARDS ASSOCIATION

CSMA/CA CARRIER SENSE MULTIPLE ACCESS/COLLISION AVOIDANCE

CSMA/CD CARRIER SENSE MULTIPLE ACCESS/COLLISION DETECTION

DC

ACP

PP

NVR

DVR

PS

JB

MG

L

DR

F 180° 360°

PTZ

CAMERA TYPE

# CAMERA NUMBER

ES

CARD READER

REQUEST-TO-EXIT

ELECTRONIC LOCK

ELECTRIC STRIKE

DOOR CONTACT

PUSH PLATE

ACCESS CONTROL PANEL

LOCKDOWN BUTTON

SECURITY DOOR RELEASE BUTTON

NETWORK VIDEO RECORDER

DIGITAL VIDEO RECORDER

POWER SUPPLY

JUNCTION BOX

MAGNETIC LOCK

CEILING MOUNTED FIXED IP CAMERA - PROVIDE (1) CATEGORY 6 CABLE TERMINATED TO SECURITY

RACK LOCATED IN SECURITY ROOM 229A.

CEILING MOUNTED 360° CAMERA - PROVIDE (1) CATEGORY 6 CABLE TERMINATED TO SECURITY

RACK LOCATED IN SECURITY ROOM 229A.

WALL MOUNTED FIXED CAMERA - PROVIDE (1) CATEGORY 6 CABLE TERMINATED TO SECURITY

RACK LOCATED IN SECURITY ROOM 229A.

ELECTRONIC SAFETY AND SECURITY GENERAL NOTES

ICM INTERCOM MASTER STATION

ICS INTERCOM SUB-STATION

F

360°

F

IC INTERCOM

HC HANDICAP PUSH PLATE

CB CODE BLUE DEVICE

EA EQUIPMENT ALARMS

SECURITY RACEWAY REQUIREMENTS GENERAL NOTES:

1. SECURITY DETAILS ARE DIAGRAMMATIC AND INTENDED FOR OWNING THE SCOPE OF THE SYSTEMS AND

REQUIREMENTS, ALL FINAL INSTALLATIONS SHALL BE BASED ON APPROVED SHOP DRAWINGS.

2. CONTRACTOR SHALL PROVIDE DETAILED SHOP DRAWINGS INDICATING FINAL CABLING AND CONDUIT

SIZES AS COORDINATED WITH APPROVED SHOP DRAWINGS PRIOR TO ROUGH-IN

3. PRIOR TO ROUGH-IN, CONTRACTOR SHALL REFER TO ARCHITECTURAL PLANS, RCPs, ELEVATIONS AND

SCHEDULES FOR ALL FINAL MOUNTING HEIGHTS AND LOCATIONS.

4. THE CONTRACTOR SHALL PROVIDE DETAILED COORDINATION DRAWINGS FOR SUBMITTAL TO ENSURE

THAT ALL SIZES, AND SYSTEMS ARE COORDINATED WITH ALL TRADES AND SYSTEMS.

5. INSTALLATION OF ALL RACEWAYS SYSTEMS SHALL BE PROVIDED IN ACCORDANCE WITH REFERENCED

STANDARDS NOTED IN SPECIFICATIONS AND CONTRACT DOCUMENTS HEREIN.

EXT

EXTERIOR

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :2

P

M

SE.000

SECURITY LEGEND

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

41 TERMINALS, CONNECTORS, DEVICES, CIRCUITS, CABLES, AND CABLE TERMINATIONS SHALL BE CLEARLY, LOGICALLY, AND PERMANENTLY MARKED DURING INSTALLATION. ALL EQUIPMENT AND CONDUITS SHALL BE IDENTIFIED.

42 ALL WIRING AND ELECTRICAL CIRCUITS SHALL BE NUMERICALLY IDENTIFIED AT BOTH ENDS AS REQUIRED BY THE CONTRACT DOCUMENTS. EACH SYSTEM CONDUIT JUNCTION BOX, PULL BOX, OR ELECTRICAL ENCLOSURE (FROM TERMINATION TO TERMINATION) CONTAINING SYSTEM CONDUCTORS, INCLUDING INITIATING DEVICE, NOTIFICATION

APPLIANCE, AND AUXILIARY FUNCTION CIRCUITS.

43 AC POWER CONDUCTORS OR GROUNDING CONDUCTORS SHALL BE UNIQUELY AND PERMANENTLY LABELED WITH A NUMBERED TAG, LABEL OR STENCIL. LABEL SYSTEM PROPOSED BY THE CONTRACTOR SHALL BE TYPEWRITTEN AND

APPROVED BY OWNER OR THEIR AUTHORIZED REPRESENTATIVE.

44 ENCLOSURES, CABINETS, HOUSINGS, CONSOLES, POWER SUPPLY ENCLOSURES, CONTROL AND TERMINAL CABINETS, CONTROL UNITS, WIRING GUTTERS AND OTHER COMPONENT HOUSINGS, BOXES AND FITTINGS OR EVERY PRODUCT DESCRIPTION, COLLECTIVELY REFERRED TO AS ENCLOSURES, SHALL BE SO FORMED AND ASSEMBLED AS TO BE

STURDY AND RIGID.

45 ALL WIRING SHALL BE RUN PERPENDICULAR OR PARALLEL TO THE FLOOR PLANE, WITH ALL BENDS MADE AT NEAT

RIGHT ANGLES.

46 ALL WIRING WITHIN THE CABINET SHALL BE PERMANENTLY ATTACHED USING SPIRAL WRAP TUBING AND NYLON WIRE TIES WITH MECHANICAL (I.E.: SCREWS, RIVETS) FASTENERS. THE USE OF SELF-ADHESIVE FASTENERS INSIDE THE

CABINET(S) IS SPECIFICALLY PROHIBITED.

47 ALL ENCLOSURE PENETRATIONS SHALL BE FROM THE BOTTOM UNLESS THE SYSTEM DESIGN REQUIRES PENETRATIONS FROM OTHER DIRECTIONS. PENETRATIONS OF INTERIOR ENCLOSURES INVOLVING TRANSITIONS OF CONDUIT FROM INTERIOR TO EXTERIOR, AND ALL PENETRATIONS ON EXTERIOR ENCLOSURES SHALL BE SEALED WITH RUBBER SILICONE SEALANT TO PRECLUDE THE ENTRY OF WATER. THE TERMINATOR SHALL BE FILLED WITH AN APPROVED SEALANT AS RECOMMENDED BY THE CABLE MANUFACTURER AND IN SUCH A MANNER THAT THE CABLE IS

NOT DAMAGED.

48 ALL WIRING WITHIN THE CABINET SHALL BE NEATLY ROUTED IN HORIZONTAL AND VERTICAL CHANNELS PARALLEL TO THE CABINET'S SIDES AND THE INTERIOR TERMINAL STRIPS. WIRING SHALL NOT BE ROUTED OVER CIRCUIT BOARDS, TRANSFORMERS, OR TERMINAL STRIPS. AS GENERAL PRACTICE, RUN ALL POWER CABLES, CONTROL CABLES, AND HIGH-LEVEL CABLES ON ONE SIDE OF AN EQUIPMENT CABINET. RUN ALL OTHER CABLES ON THE OPPOSITE SIDE OF AN EQUIPMENT CABINET. THE CONTRACTOR SHALL MAINTAIN A MINIMUM OF A TWELVE (12) INCH DISTANCE BETWEEN ALL PARALLEL RUNS OF AC ELECTRICAL POWER AND LOW VOLTAGE CONDUIT OR LOW VOLTAGE WIRING.

49 PROVIDE TESTING AND VERIFY THAT ALL SYSTEM CABLING AND FIELD WIRING IS FREE OF SHORTS, GROUNDS, OPENS, HIGH RESISTANCE, AND OTHER FAULTS PRIOR TO TERMINATION TO DEVICES AND EQUIPMENT. THE CONTRACTOR SHALL PROVIDE A DETAILED REPORT OF THE TEST TO OWNER'S SECURITY AND ITS AUTHORIZED REPRESENTATIVE.

50 ALL CONDUITS SHALL BE IN INSTALLED IN ACCORDANCE WITH NFPA 70, THE NATIONAL ELECTRICAL CODE (NEC), AMERICAN DISABILITY ACT (ADA) AND THE CONTRACT DOCUMENTS.

51 ALL CONDUIT ROUTES SHALL BE SO DESIGNED TO ENSURE THAT ALL LOW VOLTAGE WIRE AND CONDUIT MAINTAIN THE REQUIRED MINIMUM OF TWELVE-INCH (12") DISTANCE SEPARATION FROM ANY OPEN CONDUCTORS OF POWER, OR CLASS 1 CIRCUIT AND SHALL NOT BE PLACED IN ANY CONDUIT, JUNCTION BOX OR RACEWAY CONTAINING THESE

CONDUCTORS, AS PER NFPA 70, THE NATIONAL ELECTRICAL CODE (NEC).

52 ALL CONDUITS, RACEWAYS, AND OTHER ASSOCIATED ITEMS RELATED TO THE SYSTEM INSTALLED, SHALL NOT OBSTRUCT ANY PORTION OF A WINDOW, DOORWAY, STAIRWELL, OR PASSAGEWAY AND SHALL NOT INTERFERE WITH

THE OPERATION OF ANY EXISTING MECHANICAL OR ELECTRICAL EQUIPMENT.

53 ALL BACK BOXES PROVIDED FOR RECESSED CEILING INSTALLATION SHALL INCLUDE ADEQUATE ACCESS AND SHALL BE RATED FOR USE IN CEILINGS AND SHALL MEET OR EXCEED ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL

CODES.

54 ALL JUNCTION BOXES DEFINED BY THE RECORD SPECIFICATION MAY BE CONCEALED BUT MUST REMAIN ACCESSIBLE FOR SERVICE AND TESTING. SECURITY JUNCTIONS BOXES MAY BE RECESSED INTO WALL OR CEILING.

55 ALL JUNCTION BOXES AND SMALL DEVICE ENCLOSURES BELOW THE CEILING AND EASILY ACCESSIBLE TO EMPLOYEES OR THE PUBLIC SHALL BE TAMPER PROOF, MONITORED, AND COVERED WITH SUITABLE COVER PLATE. ALL JUNCTION BOXES ABOVE CEILING LEVEL IN OCCUPIED AREAS OF THE BUILDING SHALL NOT BE CONSIDERED TO BE EASILY ACCESSIBLE. ALL LOCATIONS CONTAINING SECURITY SYSTEM COMPONENTS UNDER THESE CONDITIONS SHALL

INCORPORATE SECURE TAMPERPROOF SCREWS OR SIMILAR APPROVED DEVICES.

56 ALL SYSTEM CABLING PROVIDED, AS PART OF THIS SYSTEM SHALL BE INSTALLED IN DEDICATED CONDUIT RACEWAYS, WHICH ARE NOT USED FOR ANY OTHER PURPOSE, FUNCTION, OR SYSTEM.

57 CONDUIT SHALL BE CONCEALED IN ALL FINISHED AREAS. EXPOSED CONDUIT IS PERMITTED IN ELECTRICAL, MECHANICAL AND UNFINISHED AREAS ONLY AS DETERMINED BY THE ARCHITECT PRIOR TO INSTALLATION.

58 ANY RUN OF EXPOSED CONDUIT SHALL BE PARALLEL OR AT A RIGHT ANGLE TO THE BUILDING LINES.

59 ALL DEVICES GENERATING RADIO FREQUENCIES SHALL BE CERTIFIED TO COMPLY WITH THE REQUIREMENTS OF FCC

PART 15 AND LABELED AS SET FORTH IN FCC PART 15.

60 CONTRACTOR SHALL TAKE ALL OTHER PRECAUTIONS IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS

TO PREVENT ELECTROMAGNETIC INTERFERENCE WITH DATA TRANSMISSIONS.

61 NON-SECURITY SYSTEM WIRING SHALL NOT SHARE SECURITY CONDUIT.

62 THE SECURITY SYSTEM NETWORK SHALL COMMUNICATE WITH THE SYSTEM CONTROL WORKSTATIONS THROUGH INDUSTRY STANDARD NETWORK SWITCHES AND ROUTERS AND SHALL NOT BE REQUIRED TO RESIDE ON THE SAME

SUBNET, AS THE INFORMATION TECHNOLOGY NETWORK.

63 THE SECURITY CONTRACTOR SHALL COORDINATE WITH THE CONTRACTOR OF DIVISION 08 700-DOOR HARDWARE.

64 ALL ELECTRIFIED DOORS SHALL BE OPERATIONAL FROM THE INSIDE WITHOUT USE OF A KEY OR ANY SPECIAL

KNOWLEDGE OR EFFORT PER NFPA 101.

65 THE SECURITY CONTRACTOR SHALL COORDINATE WITH THE DOOR HARDWARE CONTRACTOR AS TO INTERCONNECTION OF ALL INPUT TRIGGERS FOR RELEASE OF ELECTRICAL LOCKING HARDWARE AND CONTACT

OUTPUTS REQUIRED TO MONITOR DOOR RELATED ALARM POINTS.

66 ALL CAMERA CABLING SHALL BE CONCEALED AND PROTECTED IN A RIGID ENCASEMENT, CONDUIT, ARMORED FLEX, OR SIMILAR APPROVED PASSAGES. CAMERA PLACEMENTS IN THE FIELD ARE FORBIDDEN TO HAVE UNPROTECTED AND EXPOSED CONNECTORS, POWER CABLE, AND VIDEO FEEDS. INTEGRATED ARMATURES THAT PASS THE CABLING FROM THE CAMERA TO THE WALL / JUNCTION BOX WITHOUT EXPOSING THE CABLING AT ANY POINT SHALL BE DEEMED

ACCEPTABLE.

67 PROVIDE BACK BOX AND ASSOCIATED CONDUIT, LOCKNUTS, COUPLINGS, THREADED BUSHINGS, AND PULL ROPE FOR

ALL DEVICES AS INDICATED ON DRAWINGS AND AS SPECIFIED.

68 THE FINAL FIELD PLACEMENT AND FIELD OF VIEW FOR EACH CAMERA LOCATION SHALL BE DETERMINED BY ON SITE CONDITIONS. PRIOR TO THE PURCHASE OF ANY (CCTV) HARDWARE THE CONTRACTOR SHALL OBTAIN WRITTEN ACCEPTANCE OF PROPOSED PLACEMENTS AND ASSOCIATED FOCAL LENGTHS FROM THE OWNER OR ITS AUTHORIZED

REPRESENTATIVE.

80 ALL PENETRATIONS THROUGH FIRE RATED BUILDING STRUCTURES, WALLS, AND FLOORS SHALL BE SEALED WITH AN APPROPRIATE FIRE STOP SYSTEM. THIS REQUIREMENT APPLIES TO THROUGH PENETRATIONS (COMPLETE PENETRATION) AND MEMBRANE PENETRATIONS (THROUGH ONE SIDE OF A HOLLOW FIRE RATED STRUCTURE). ANY PENETRATING ITEMS I.E., RISER SLOTS AND SLEEVES, CABLES, CONDUIT, CABLE TRAY, AND RACEWAYS, ETC. SHALL BE PROPERLY FIRE STOPPED. THE CONTRACTOR SHALL ENSURE THAT ANY FIRE STOP SYSTEMS SHALL BE UL

CLASSIFIED TO ASTM E8 14 (UL 1479).

81 THE CONTRACTOR SHALL ENSURE THAT ALL FIRE STOP SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATIONS AND SHALL BE COMPLETELY INSTALLED AND AVAILABLE FOR INSPECTION BY

THE LOCAL INSPECTION AUTHORITIES PRIOR TO CABLE SYSTEM ACCEPTANCE.

82 UPON SUCCESSFUL COMPLETION OF THE INSTALLATION, THE CONTRACTOR SHALL CONDUCT FULL SYSTEM TESTING TO ASSURE THAT THE SYSTEMS ARE CORRECTLY INSTALLED AND FULLY OPERATIONAL. CONFIRM IN WRITING TO THE ARCHITECT THAT ALL ASPECTS OF THE SYSTEM HAVE BEEN TESTED BY THE CONTRACTOR AND FOUND TO BE FULLY

OPERATIONAL AND READY FOR FINAL ACCEPTANCE TESTING.

83 AT THE CONCLUSION OF TESTING PROVIDE (2) COPIES OF ALL TEST REPORT DOCUMENTATION OF THE TESTS THAT SHALL REFLECT THE DATE, TIME, AND SYSTEM TESTING RESULTS. ADJUST, BALANCE AND TUNE ALL EQUIPMENT AS REQUIRED FOR OPTIMUM QUALITY TO MEET MANUFACTURER'S PUBLISHED PERFORMANCE SPECIFICATIONS AND

OWNERS REQUIREMENTS.

1 ALL WIRING AND CABLE BETWEEN DEVICES SHALL BE IN ACCORDANCE WITH THE OPERATING REQUIREMENTS OF THE DESIGNATED SYSTEM AND SHALL SUPPORT COMMUNICATIONS FOR POINT IDENTIFICATION AND ACCESS CONTROL

TRANSACTIONS TO/FROM EACH DEVICE.

2 THE CONTROL WIRING BETWEEN FIELD DEVICES, REMOTE ACCESS CONTROL EQUIPMENT AND FIELD PANELS/DATA GATHERING PANELS SHALL BE A MINIMUM OF No. 18 AWG AND SHALL BE COLOR-CODED.

3 PROVIDE WIRING FROM THE SMS FIELD PANEL TO THE INSTALLED FIRE ALARM SYSTEM SUCH THAT IN THE EVENT OF A FIRE ALARM OR WHEN THE FIRE ALARM SYSTEM IS ACTIVATED, ALL DOORS FITTED WITH ELECTROMAGNETIC LOCKS SHALL REVERT TO FAIL SAFE MODE OF OPERATION IN ACCORDANCE WITH THE LOCAL AUTHORITY HAVING

JURISDICTION AND OWNER OR THEIR AUTHORIZED REPRESENTATIVE.

4 ALL NON STAIRWELL DOORS FITTED WITH ELECTRIC MORTISE LOCKS SHALL REVERT TO A FAIL SECURE MODE OF OPERATION IN ACCORDANCE WITH THE LOCAL AUTHORITY HAVING JURISDICTION AND OWNER'S SECURITY.

5 ALL STAIRWELL DOORS FITTED WITH ELECTRIC MORTISE LOCKS SHALL REVERT TO A FAIL SAFE MODE OF OPERATION.

6 PROVIDE A HARD WIRED CONNECTION TO A 120 VAC, 20AMP EMERGENCY CIRCUIT THAT IS DEDICATED TO SECURITY FOR EACH SECURITY EQUIPMENT POWER SUPPLY LOCATION AS INDICATED ON THE DRAWINGS. THE CIRCUIT CONNECTION SHALL BE PROVIDED WITHIN A BACK BOX, SURFACE MOUNTED AT 18" A.F.F. UNLESS OTHERWISE NOTED.

TERMINATE WIRE ENDS WITH INSULATED WIRE NUTS.

7 REVIEW ALL CONTRACT DRAWINGS AND SURVEY EXISTING SITE CONDITIONS PRIOR TO ORDERING EQUIPMENT OR

PROCEEDING WITH WORK.

8 DRAWINGS SHALL BE USED BY THE CONTRACTOR AS A REFERENCE FOR THE REQUIREMENT AND LOCATION OF THE SYSTEM COMPONENTS. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO ACQUAINT THEMSELVES WITH ALL OF THE CONTRACT DRAWINGS, AND CONFIRM THE REQUIRED QUANTITIES OF DEVICES AND SPECIFIC OPTIONS ON

LOCATION.

9 PERFORM ALL WORK, PROVIDE PRODUCTS, SYSTEM INTEGRATION, COORDINATION, ENGINEERING, AND DESIGN WORK REQUIRED FOR THE PROJECT IN ORDER TO ENSURE THE PROPER INSTALLATION OF THE COMPLETE AND FULLY

OPERATIONAL SYSTEMS PURSUANT TO THE CONTRACT DOCUMENTS.

10 ALL SYSTEMS PROVIDED SHALL BE IN ACCORDANCE WITH THE MOST CURRENT REVISION OF THE FEDERAL, STATE, AND LOCAL CODES AND STANDARDS. THE AUTHORITY HAVING JURISDICTION SHALL PROVIDE FINAL CLARIFICATION OF CODE REQUIREMENTS. CONFLICT OF ANY CODE REQUIREMENT WILL REQUIRE THE ADAPTATION OF THE MORE STRINGENT REQUIREMENT FOR THE APPLICATION UNLESS A VARIANCE IS AUTHORIZED BY THE LOCAL AUTHORITY

HAVING JURISDICTION.

11 PROVIDE ALL COMPONENTS, INTERCONNECTION CONDUIT, CABLE/WIRE, APPURTENANCES, AND MATERIALS AS

REQUIRE TO FORM A COMPLETE COORDINATED SYSTEM READY FOR OPERATION.

12 PROVIDE ALL PLAN CHECKS, PERMITS, AND LICENSES NECESSARY FOR THE EXECUTION OF WORK AS APPLICABLE FOR THE PROJECT. ALL FEES, CHANGES, AND OTHER ASSOCIATED COSTS INCURRED BY THE FOREGOING SHALL BE BORNE

BY THE CONTRACTOR.

13 THE CONTRACTOR SHALL PROVIDE A QUALIFIED AND COMPETENT FACTORY TRAINED AND STATE LICENSED FIELD SUPERVISOR ON-SITE TO ENSURE THE PROPER INSTALLATION OF ALL SYSTEMS SPECIFIED AND IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. THE CONTRACTOR SHALL COORDINATE CONSTRUCTION ACTIVITIES WITH OTHER

CONTRACTORS, TRADES, AND OWNER OR THEIR AUTHORIZED REPRESENTATIVE.

14 THE CONTRACTOR SHALL PROVIDE FACTORY TRAINED AND STATE LICENSED TECHNICIANS FOR THE INSTALLATION

AND SHALL PROVIDE PROOF OF SUCH SYSTEMS AUTHORIZED TRAINING.

15 PROVIDE ALL WIRING FROM EQUIPMENT HARDWARE MANUFACTURER'S TERMINAL STRIPS TO FINAL CONNECTION

POINTS OF EQUIPMENT.

16 THE CONTRACTOR SHALL BE RESPONSIBLE FOR FIELD VERIFYING ALL EXISTING CONDITIONS AND ANY CRITICAL DIMENSIONS ASSOCIATED WITH THE SCOPE OF WORK PRIOR TO SUBMITTING THE CONSTRUCTION BID. THE CONTRACTOR SHALL CONFIRM THAT ALL WORK OUTLINED WITHIN THE CONTRACT DOCUMENTS CAN BE ACCOMPLISHED AS SHOWN, AND SHALL NOTIFY IN WRITING AN AUTHORIZED REPRESENTATIVE OF ANY CONDITIONS

ENCOUNTERED WHICH MAY AFFECT BUILDING CODE COMPLIANCE.

17 VERIFY PARTITION LOCATIONS, AND AVOID CONFLICTS WITH LIGHTS, DIFFUSERS, GRILLS, AND OTHER LIKE OBSTRUCTIONS. LOCATIONS OF ALL VISIBLE DEVICES AND EQUIPMENT SHALL BE COORDINATED WITH THE ARCHITECT

FOR REVIEW AND APPROVAL PRIOR TO INITIATION OF WORK.

18 COORDINATE A FINAL SECURITY SYSTEM EQUIPMENT LAYOUT AND ROUTING OF THE CONDUIT WITH THE CONTRACT DOCUMENTS. ANY CONFLICTS DISCOVERED SHALL IMMEDIATELY BE BROUGHT TO THE ATTENTION OF THE OWNER

FOR REVIEW AND APPROVAL PRIOR TO INITIATION OF WORK.

19 EQUIPMENT AND COMPONENTS SHOWN ON THESE PLANS ARE DIAGRAMMATIC IN NATURE AND ARE NOT TO BE SCALED FOR EXACT DEVICE LOCATIONS. CONTRACTOR SHALL LOCATE DEVICES BASED ON APPLICABLE CODE, KEY

NOTES, AND AS DESIGNED BY THE ARCHITECT.

20 INSTALL ALL MATERIALS AND EQUIPMENT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S DIRECTION, TESTING

AND OPERATIONAL PROCEDURES.

21 ALL MATERIALS, DEVICES, AND EQUIPMENT SHALL BE UNUSED, OF CURRENT MANUFACTURER, AND MEET OR EXCEED THE LATEST PUBLISHED SPECIFICATIONS OF THE MANUFACTURER. DEVICES AND EQUIPMENT SHALL BE THE LATEST MODEL OF THE MANUFACTURER UNLESS OTHERWISE INDICATED, OR UNLESS SUCH MODEL FAILS TO MEET THE

REQUIREMENTS OF THE CONTRACT DOCUMENTS.

22 ALL ELECTRONICS COMPONENTS SHALL BE STANDARD, UNMODIFIED PRODUCTION MODELS EXCEPT AS NOTED WITH THE LATEST FIRMWARE/BIOS OFFERED BY THE MANUFACTURER AT THE TIME OF THE FINAL TEST.

23 PROTECT ALL EXISTING WORK, AND THE WORK OF OTHER ASSOCIATED TRADES FROM DAMAGE. ALL EQUIPMENT PROVIDED SHALL BE KEPT INTERNALLY CLEAN AND PROTECTED AGAINST BLOWING DUST, WIND, STORMS, SUN, FLOOD, RAIN, SNOW, HEAT, RAIN, MOISTURE, AND ANY OTHER DAMAGING FACTORS. ALL

INSTALLATION WORK SHALL BE COVERED AND PROTECTED AGAINST DAMAGE.

24 EQUIPMENT AND MATERIALS SHALL BE PROPERLY STORED, ADEQUATELY PROTECTED AND CAREFULLY HANDLED TO

PREVENT DAMAGE BEFORE AND DURING INSTALLATION.

25 ELECTRICAL CONTRACTOR SHALL PROVIDE PRIMARY, DEDICATED ELECTRICAL POWER (120/220 VAC).

26 ALL PRIMARY CONTROL PANELS, COMMUNICATION TRANSPORTATION DEVICES, POWER SUPPLIES NETWORK VIDEO RECORDERS, AND DIGITAL VIDEO RECORDERS SHALL BE CONNECTED TO UPS BACKUP CIRCUITS, BATTERY BACKUP, OR GENERATOR POWER BACKUP SYSTEM.

27 PROVIDE ALL THE INTERCONNECTIONS BETWEEN POWERED JUNCTION BOXES AND THE SECURITY EQUIPMENT.

28 ADHERE TO ALL SYSTEM AND COMPONENT GROUNDING REQUIREMENTS AS SPECIFIED BY THE EQUIPMENT

MANUFACTURERS.

29 PROVIDE SURGE SUPPRESSION, GROUNDING AND BONDING THAT WILL EFFECTIVELY PROTECT, WITHIN TESTED LIMITS, THE SYSTEMS HARDWARE AND EQUIPMENT AGAINST LIGHTNING TRANSIENTS, INTERNAL AND EXTERNAL SWITCHING TRANSIENTS, AND OTHER SURGE TRANSIENTS THROUGHOUT THE USEFUL LIFE OF THE SYSTEM.

30 ALL WIRING SHALL BE PROPERLY SUPPORTED AND INSTALLED IN CONDUIT AND CABLE TRAY, ON CENTER AS

REQUIRED IN CONTRACT DOCUMENTS.

31 ALL CONDUIT FILL SHALL NOT EXCEED 40 PERCENT OF INTERIOR CROSS SECTIONAL AREA WHERE THREE OR MORE

CABLES ARE CONTAINED WITHIN A SINGLE CONDUIT.

32 CABLES, RACEWAYS, AND CONDUIT SHALL NOT BE SUPPORTED FROM DUCTWORK, PIPING, PLUMBING SYSTEMS, CEILING TILE AND LIGHTING FIXTURE SUSPENSION WIRES OR BUILDING STRUCTURE.

33 CABLES SHALL BE ROUTED IN CONDUIT OR OTHER SUITABLE RACEWAY SUBJECT TO ACCEPTANCE BY THE ARCHITECT.

34 AT LOCATIONS WHERE CABLES PASS THROUGH METAL STUDS OR DOOR FRAMES, THE CONTRACTOR SHALL INSTALL A

BUSHING OR GROMMET TO PREVENT DAMAGE TO THE CABLES.

35 ALL CABLES MUST BE FREE OF TENSION AT BOTH ENDS AND OVER THE ENTIRE LENGTH OF THE RUN.

36 CABLE TIES AND SUPPORTS SHALL NOT PINCH, BIND, CRIMP, OR IN ANY WAY CAUSE PHYSICAL OR ELECTRICAL CHARACTERISTIC DAMAGE TO THE CABLING. THE CONTRACTOR SHALL ASSURE THAT DURING AND UPON COMPLETION OF THE INSTALLATION, ALL CABLES ARE FREE OF KINKS, SHARP BENDS, TWISTS, GOUGES, CUTS OR ANY OTHER

PHYSICAL DAMAGE.

37 ALL CABLING SHALL BE PLENUM RATED IN ACCORDANCE WITH THE NEC.

38 PLENUM RATED CABLE TIES AND CABLE SUPPORTS SHALL BE UTILIZED IN ALL PLENUM RATED SPACES.

39 ALL CABLE RUNS SHALL BE CONTINUOUS BETWEEN DEVICES WITHOUT SPLICES. CONNECTIONS SHALL BE MADE USING TERMINAL BLOCKS. WIRES CONNECTED TOGETHER SHALL HAVE THE SAME COLOR INSULATION. ALL CONNECTIONS SHALL BE ACCESSIBLE FOR INSPECTION AND SERVICES AND SHALL BE CLEARLY IDENTIFIED ON THE CONTRACTOR'S AS-BUILT DRAWINGS. ALL DEVICE BACK BOXES, JUNCTION BOXES AND PULL BOXES SHALL BE LABELED AND

ACCESSIBLE FOR INSPECTION AND MAINTENANCE.

40 WIRING COLOR CODE SHALL BE MAINTAINED THROUGHOUT THE INSTALLATION AS REQUIRED BY THE SPECIFICATIONS.

Number: Revisions: Date:

CONFORMED CONSTRUCTION

DOCUMENTS

UPDN

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

X

EXISTING CAMERA TO BE DEMOLISHED. REMOVE CAMERA

AND HAND OVER TO VA SECURITY. DEMOLISH ALL CABLING

BACK TO ITS SOURCE PANEL(S)

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :3

P

M

SE.101

SECURITY DEMOLITION PLAN LEVEL 1

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

Number: Revisions: Date:

UP

DN

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

DEMOLISH ALL SECURITY EQUIPMENT . REMOVE ALL WIRING

BACK TO ITS SOURCE PANEL(S).

DEMOLITION NOTES:

1. IDENTIFY ALL CABLING AND DEVICES AFFECTED BY THE DEMOLITION OF EXISTING

WALL, ANY CABLES OR EQUIPMENT SERVING OTHER AREAS SHALL BE PROTECTED

FROM DEMOLITION.

2. REFER TO NEW WORK SECURITY DRAWINGS FOR ADDITIONAL INFORMATION.

3. PROVIDE TEMPORARY SERVICES TO ANY SECURITY DEVICE FED FROM

DEMOLISHED SECURITY EQUIPMENT.

LOCATION OF EXISTING SECURITY PANELS.

COORDINATE THE TEMPORARY RELOCATION

OF ANY EXISTING PANELS WITH PROVIDENCE

VA SECURITY PRIOR DEMOLITION OF

EXISTING WALL.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :3

P

M

SE.102

SECURITY DEMOLITION PLAN LEVEL 2

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

Number: Revisions: Date:

UPDN

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

ABC

DEFGHI

EXT

EXT

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :3

P

M

SE.201

SECURITY PLAN LEVEL 1

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

KEYED NOTES:

EXTERIOR CAMERAS SHALL BE SURFACE MOUNTED TO STRUCTURE ABOVE, COORDINATE BUILDING PENETRATION WITH ARCHITECT PRIOR TO START OF WORK. CAMERAS SHALL BE PELCO SARIX IME 3 MP ENVIRONMENTAL MINI DOMES.

Number: Revisions: Date:

UP

DN

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

CR

F

CR

F

CR

SE.700

SE.700

SE.700

DR

COORDINATE MOUNTING OF

THE DOOR RELEASE BUTTON

WITH ARCHITECT PRIOR TO

INSTALLATION.

CB

CB

CB

CB

NUMBERED NOTES:

CODE BLUE SECURITY PUSH BUTTONS SHALL BE SAFETY TECHNOLOGY INTERNATIONAL STOPPER

STATIONS MODEL NUMBER SS2409EM-EN WITH CLEAR COVER STI SS24420ZA-EN. THE BUTTON SHALL BE BLUE WITH THE CUSTOM LABEL CODE BLUE. THE PUSH BUTTON SHALL TERMINATE ON THE JOHNSTON

CONTROLS PEGASYS SYSTEM LOCATED IN SECURITY ROOM 229A.

PROVIDE (2) PELCO SARIX IME 3 MP MINI DOMES CAMERAS POINTED IN OPPOSITE DIRECTIONS.

GENERAL NOTES:

1. REFRIGERATOR ALARMS SHALL CONNECT TO THE JOHNSTON CONTROLS PEGASYS SYSTEM FOR

REPORTING TO THE VA DISPATCH PEGASYS WORKSTATION COMPUTER. COORDINATE THE LCATION AND QUANTITY OF ALARMS WITH THE ARCHITECT AND PROVIDE (1) 18/4 AWG CABLE TO THE PEGASYS

SYSTEM LOCATED IN ROOM 229A.

2. COORDINATE FIRE ALARM DOOR RELEASE WITH ELECTRICAL CONTRACTOR PRIOR TO START OF

WORK

CR

SE.700

F

F

C200D

A-2-S

C200C A

201A

SE.202

KEYED NOTES:

PROVIDE JCI SPA1B800-3E10 CONTROL PANEL ALONG BACK WALL OF SECURITY

ROOM 229A. COORDINATE THE RELOCATION/RECONFIGURATION OF ALL EXISTING

ACCESS CONTROL EQUIPMENT WITH VAMC SECURITY PRIOR TO START OF WORK.

SECURITY NETWORK CABLING AND FIBER OPTIC CABLING NETWORK ARE EXISTING

TO BE RELOCATED. COORDINATE CONNECTION OF SECURITY EQUIPMENT WITH

VAMC IT DEPARTMENT.

WALL MOUNTED CABINET IS EXISTING TO BE RELOCATED. PROVIDE THE

FOLLOWING NETWORK EQUIPMENT TO CONNECT THE ADDED CAMERAS TO THE

VIDEO SURVEILLANCE NETWORK LOCATED IN BUILDING 4.

- (1) CISCO CATALYST WS-C3850-24XU-S, STACKABLE X SERIES 24 PORT SWITCH

- (2) CISCO PWR-C1-1100WAC POWER SUPPLY MODULE 800W

- (1) CISCO C3850-NM-4-10G, 4 X GIGABIT ETHERNET NETWORK MODULE

- (1) CISCO XPS2200 REDUNDANT POWER SUPPLIES

- (2) CISCO XPS2200 POWER CABLES

- (1) SINGLE MODE PAIR SC TYPE PATCH CABLES

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :4

P

M

SE.202

SECURITY PLAN LEVEL 2

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

Number: Revisions: Date:

1/2" = 1'-0"

LEVEL 2 - EXISTING SECURITY ROOM

ACCESS/ENTRY SIDE

INTERIOR/EGRESS SIDE

ACCESSIBLE CEILING

TO ACCESS CONTROL PANEL

JUNCTION BOX ABOVE

ACCESSIBLE CEILING

EL

PROXIMITY

CARD READER

JB

DOOR

ELECTRO MECHANICAL

LOCKSET WITH INTEGRAL

REQUEST TO EXIT

CONCEALED DOOR

CONTACT SWITCH (TYPICAL)

DC

FINISHED FLOOR

CR

POWER TRANSFER

HINGE

3/4" CONCEALED CONDUIT

1-1/4" CONDUIT

DOOR FRAME

RX

PROXIMITY

CARD READER

CR

ACCESS/ENTRY SIDE

INTERIOR/EGRESS SIDE

JB

ACCESSIBLE CEILING

ELECTRIC STRIKE

JUNCTION BOX ABOVE

ACCESSIBLE CEILING

CONCEALED

DOOR

CONTACT SWITCH

DOOR

FINISHED FLOOR

DCES

3/4" CONCEALED CONDUIT

DOOR FRAME

TO ACCESS CONTROL PANEL

1-1/4" CONDUIT

RX

CR ACCESS/ENTRY SIDE

INTERIOR/EGRESS SIDE

ACCESSIBLE CEILING

TO ACCESS CONTROL PANEL

JUNCTION BOX ABOVE

ACCESSIBLE CEILING

MG

JB

DOOR

DELAYED EGRESS

MAGNETIC LOCK

(TYPICAL)

FINISHED FLOOR

MG

MGMG

PP

DOOR FRAME

1-1/4" CONDUIT

3/4" CONCEALED CONDUIT

PROXIMITY

CARD READER

CABLE TYPE KEYNOTES

(1) #18 AWG, 8-CONDUCTOR SHIELDED TWISTED PAIR CABLE

(1) #18 AWG, 2-CONDUCTOR UNSHIELDED TWISTED PAIR CABLE

(1) #16 AWG, 2-CONDUCTOR UNSHIELDED TWISTED PAIR CABLE

(1) #16 AWG, 2-CONDUCTOR UNSHIELDED TWISTED PAIR CABLE

(1) #16 AWG, 4-CONDUCTOR UNSHIELDED TWISTED PAIR CABLE

(1) #18 AWG, 4-CONDUCTOR UNSHIELDED TWISTED PAIR CABLE

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :4

P

M

SE.700

SECURITY DETAILS

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

1" = 1'-0"

SECURITY OPENING-DOUBLE UNEVEN ACCESS CONTROLLED DOOR

1" = 1'-0"

SECURITY OPENING-SINGLE ACCESS CONTROLLED DOOR WITH ELECTRIC STRIKE

1" = 1'-0"

SECURITY OPENING-DOUBLE INTERIOR ACCESS CONTROLLED DOOR WITH MAG LOCKS

Number: Revisions: Date:

ACCESSIBLE CEILING - SEE ARCHITECTURAL

RCP

CATEGORY CABLE TO NEAREST

TELECOMMUNICATIONS ROOM

CAMERA - REFER TO PLANS AND

SPECIFICATIONS FOR ADDITIONAL

INFORMATION

1" CONDUIT TO NEAREST

TELECOMMUNICATIONS ROOM

PROVIDE 4-11/16"x4-11/16"x3" BACK BOX

CATEGORY PATCH CORD

TO CAMERA

1-PORT SURFACE MOUNTED BOX

1G DEVICE PLATE

TYPICAL CAMERA HOUSING

CADDY 512A ADJUSTABLE

SNAP-ON CEILING BOX HANGER

1" CONDUIT TO NEAREST

TELECOMMUNICATIONS ROOM

CATEGORY CABLE TO NEAREST

TELECOMMUNICATIONS ROOM

WALL MOUNTED CAMERA MOUNTING

ASSEMBLY

PROVIDE 4-11/16"x4-11/16"x3" BACK BOX

PARTITION - SEE ARCHITECTURAL

FLOOR PLANS

1-PORT SURFACE MOUNTED BOX

1G DEVICE PLATE

CAMERA HOUSING

CAMERA - REFER TO PLANS AND

SPECIFICATIONS FOR ADDITIONAL

INFORMATION

CATEGORY

PATCH CORD TO

CAMERA

1" CONDUIT TO NEAREST

TELECOMMUNICATIONS ROOM

CATEGORY CABLE TO NEAREST

TELECOMMUNICATIONS ROOM

PROVIDE 4-11/16"x4-11/16"x3" BACK BOX

PARTITION - SEE ARCHITECTURAL

FLOOR PLANS

1-PORT SURFACE MOUNTED BOX

1G DEVICE PLATE

CAMERA HOUSING

CAMERA - REFER TO PLANS AND

SPECIFICATIONS FOR ADDITIONAL

INFORMATION

CATEGORY 6 PATCH CORD TO

CAMERA

3/8" = 1'-0"

TYPICAL SECURITY CAMERA - CEILING MOUNTED

6" = 1'-0"

TYPICAL SECURITY CAMERA - WALL MOUNTED WITH BRACKET

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :4

P

M

SE.701

SECURITY DETAILS

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

6" = 1'-0"

TYPICAL SECURITY CAMERA - WALL MOUNTED

Number: Revisions: Date: