36E77619R0086-017.pdf

POI POINT OF INTERFACE

POTS PLAIN OLD TELEPHONE SERVICE

PR PAIR

PTSS PASSIVE TRANSMISSION SUBSYSTEM

PVC POLYVINYL CHLORIDE

SE SERVICE ENTRANCE

SER SATELLITE EQUIPMENT ROOM

SI SYSTEM INTERNATIONAL

SL SLEEVE

SMPS SWITCHED MODE POWER SUPPLY

SNA SYSTEMS NETWORK ARCHITECTURE

SP SERVICE PROVIDER

SPC STORED PROGRAM CONTROL

SPD SURGE PROTECTION DEVICE

SPG SINGLE-POINT GROUND

STA STATION

STP SHIELDED TWISTED PAIR

SW STATION WIRE

SWB SWITCHBOARD

SYS SYSTEM

TB TERMINAL BLOCK

TBBC TELECOMMUNICATIONS BACKBONE BONDING CONDUCTOR

TBC TELECOMMUNICATION BONDING CONDUCTOR

TC TELECOMMUNICATIONS CLOSET

TDM TIME DIVISION MULTIPLEXING

TEBC TELECOMMUNICATIONS EQUIPMENT BONDING CONDUCTOR

TEL TELEPHONE

TELCO TELEPHONE COMPANY

TERM TERMINAL

TGB TELECOMMUNICATIONS GROUNDING BUSBAR

THD TOTAL HARMONIC DISTORTION

TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION

TM TRANSFORMER MAINTENANCE HOLE

TMGB TELECOMMUNICATIONS MAIN GROUNDING BUSBAR

TO TELECOMMUNICATIONS OUTLET

TPDDI TWISTED PAIR DISTRIBUTED DATA INTERFACE

TPPMD TWISTED PAIR PHYSICAL MEDIUA DEPENDENT

TR TELECOMMUNICATIONS ROOM

TSB TELECOMMUNICATIONS SYSTEM BULLETIN

TT TELEPHONE TERMINAL

TTB TELEPHONE TERMINAL BOARD

TTY TEXT TELEPHONES

TVSS TRANSIENT VOLTAGE SURGE SUPPRESSOR

TYP TYPICAL

UG UNDERGROUND

UL UNDERWRITERS LABORATORIES

UPS UNINTERRUPTIBLE POWER SUPPLY

UTP UNSHIELDED TWISTED PAIR

ISDN INTEGRATED SERVICES DIGITAL NETWORK

ISO INTEGRATED STANDARDS ORGANIZARION

IW INSIDE WIRING (CABLE)

KHz KILOHERTZ

KTS KEY TELEPHONE SYSTEM

LAN LOCAL AREA NETWORK

LASER LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION

LATA LOCAL ACCESS TRANSPORT AREA

LBO LINE BUILDOUT

LEC LOCAL EXCHANGE CARRIER

LED LIGHT EMITTING DIODE

LOCAP LOW CAPACITANCE

MAP MANUFACTURING AUTOMATION/PROTOCOL

MAX MAXIMUM

MC MAIN CROSS-CONNECT

MDF MAIN DISTRIBUTION FRAME

M/G MOTOR/GENERATOR SET

MH MAINTENANCE HOLE

MICRON MICROMETER

MIN MINIMUM

MISC MISCELLANEOUS

MODEM MODULATOR/DEMODULATOR

MPOP MINIMUM POINT OF PRESENCE

MTT MAIN TELEPHONE TERMINAL

N NEWTON

NEC NATIONAL ELECTRIC CODE

NESC NATIONAL ELECTRIC SAFETY CODE

NI NETWORK INTERFACE

NIC NOT IN CONTRACT

NID NETWORK INTERFACE DEVICE

NIU NETWORK INTERFACE UNIT

NRTL NATIONALLY RECOGNIZED TESTING LABORATORY

NTS NOT TO SCALE

OC ON CENTER

OD OUTSIDE DIAMETER

OFNP OPTICAL FIBER NON-CONDUCTIVE PLENUM

OFNR OPTICAL FIBER NON-CONDUCTIVE RISER

OPD OVERCURRENT PROTECTION DEVICE

OPE OUTSIDE PLANT ENGINEER

OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION

OSP OUTSIDE PLANT

PAM PULSE AMPLITUDE MODULATE

PB PULL BOX

PBX PRIVATE BRANCH EXCHANGE

PCM PULSE CODE MODULATION

PIC POLYETHYLENE INSULATED CONDUCTOR

PL PRIVATE LINES

PLT PLANT

PM PHASE MODULATION

D/A DIGITAL TO ANALOG CONVERSION

DAF DEDICATED ACCESS FACILITY

DB DECIBEL

DC DIRECTED CURRENT

DCE DATA CIRCUIT-TERMINATION EQUIPMENT

DCO DIGITAL CENTRAL OFFICE

DD DISTRIBUTION DESIGNER

DEMARC DEMARCATION POINT

DGM DATA GRADE MEDIUM

DTE DATA TERMINAL EQUIPMENT

DW DISTRIBUTION WIRE

DWG DRAWING(S)

EBC EQUIPMENT BONDING CONDUCTOR

EC ELECTRICAL CONTRACTOR

EF ENTRANCE FACILITY

EIA ELECTRONICS INDUSTRY ASSOCIATION

ELEC ELECTRICAL

EMC ELECTROMAGNETIC COMPATABILITY

EMI ELECTROMAGNETIC INTERFACE

EMR ELECTROMAGNETIC RADIATION

EMT ELECTRICAL METALLIC TUBING

ESS ELECTRONIC SWITCHING SYSTEM

ETV EDUCATIONAL TELEVISION

E/W EQUIPPED WITH

EXCH EXCHANGE

EXT EXTENSION

FCC FEDERAL COMMUNICATIONS COMMISSION

FD FLOOR DISTRIBUTION

FDDI FIBER DISTRIBUTION DATA INTERFACE

FDM FREQUENCY DIVISION MULTIPLEXING

FDR FEEDER

FO FIBER OPTIC

FOTP FIBER OPTIC TRANSMISSION SYSTEM

FREQ FREQUENCY

FTP FOIL TWISTED PAIR

GA GAUGE

GEC GROUNDING ELECTRIC CONDUCTOR

GHz GIGAHERTZ

GND GROUND

HC HORIZONTAL CROSS-CONNECT

HF HIGH FREQUENCY

HH HANDHOLE

HVAC HEATING, VENTILATION AND AIR CONDITIONING

Hz HERTZ

IC INTERMEDIATE CROSS-CONNECT

ICEA INSULATED CABLE ENGINEERS ASSOCIATION

IDC INSULATION DISPLACEMENT CONNECTION

IDF INTERMEDIATE DISTRIBUTION FRAME

IEEE INTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS

8P8C 8-POSITION, 8-CONDUCTOR

AC ALTERNATING CURRENT

A/D ANALOG TO DIGITAL CONVERSION

ACO ANALOG CENTRAL OFFICE

ADA AMERICANS WITH DISABILITIES ACT

ADO AUXILIARY DISCONNECT OUTLET

AER AERIAL

AFF ABOVE FINISHED FLOOR

AIA AMERICAN INSTITUTE OF ARCHITECTS

AM AMPLITUDE MODULATION

ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

ARMM PIC RISER, EXPANDED POLYETHYLENE PVC, 24 AWG, ALVYN

ASCII AMERICAN STANDARD CODE FOR INFORMATION INTERCHANGE

ATM ASYNCHRONOUS TRANSFER MODE

AWG AMERICAN WIRE GAUGE

B BURIED

BC BONDING CONDUCTOR

BBISDN BROADBAND INTEGRATED SERVICES DIGITAL NETWORK

BD BUILDING DISTRIBUTOR

BDF BUILDING DISTRIBUTION FRAME

BEF BUILDING ENTRANCE FACILITY

BER BIT ERROR RATE

BIC BUILDING INDUSTRY CONSULTANT

BICSI BUILDING INDUSTRY CONSULTING SERVICES

BRISDN BASIC RATE INTEGRATED SERVICES DIGITAL NETWORK

BTU BRITISH THERMAL UNIT

CA CABLE

CATV CABLE TELEVISION

CBC COUPLED BONDING CONDUCTOR

CC COMMUNICATIONS CONTRACTOR

CCITT THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE

CD CONDUIT

CDDI COPPER DISTRIBUTED DATA INTERFACE

CDF COPPER DISTRIBUTION FRAME

CDO COMMUNITY DIAL OFFICE

CER COMPUTER EQUIPMENT ROOM

CIRC CIRCUIT

CFC COMMUNICATIONS FLAT CABLE

CLO CLOSET

CO CENTRAL OFFICE

CODEC CODER/DECODER

COE CENTRAL OFFICE EQUIPMENT

COT CENTRAL OFFICE TERMINAL

CPC CUSTOMER PREMISES COMMUNICATIONS

CPE CUSTOMER PREMISES EQUIPMENT

CPU CENTRAL PROCESSING UNIT

CSA CANADIAN STANDARDS ASSOCIATION

CSMA/CA CARRIER SENSE MULTIPLE ACCESS/COLLISION AVOIDANCE

CSMA/CD CARRIER SENSE MULTIPLE ACCESS/COLLISION DETECTION

GENERAL TELECOMMUNICATIONS LEGEND

GENERAL DEMOLITION NOTES:

1. REFER TO ARCHITECTURAL DRAWINGS FOR THE FULL EXTENT OF THE SCOPE OF WORK. THE TECHNOLOGY SCOPE OF WORK MAY EXTEND BEYOND THE AREA DEFINED BY THE ARCHITECTURAL DEMOLITION PLANS TO FULLY COMPLY WITH VARIOUS REQUIREMENTS DEFINED BY THESE

NOTES.

2. THE TECHNOLOGY DEMOLITION PLANS INDICATE THE GENERAL INTENT AND ARE NOT INTENDED TO SHOW ALL ITEMS TO BE REMOVED OR RETAINED. THE TECHNOLOGY CONTRACTOR SHALL VISIT THE SITE PRIOR TO THE SUBMISSION OF BIDS TO BECOME FAMILIAR WITH THE ACTUAL CONDITIONS AND EXTENT OF WORK. DEVICES AND EQUIPMENT LOCATED ON THE WALL AND/OR CEILING TO BE REMOVED SHALL BE DISCONNECTED AND MADE SAFE. THE TECHNOLOGY CONTRACTOR SHALL NOTIFY THE OWNER'S REPRESENTATIVE OF ANY UNANTICIPATED

HIDDEN CONDITIONS ENCOUNTERED DURING DEMOLITION.

3. THE TECHNOLOGY CONTRACTOR SHALL BE RESPONSIBLE FOR THE REPAIR OF ALL SYSTEMS OR BUILDING COMPONENTS DAMAGED DURING THE EXECUTION OF THE WORK. DAMAGE SHALL INCLUDE BUT NOT BE LIMITED TO DESTRUCTION OR DISPOSAL OF ITEMS INTENDED TO REMAIN OR TO

BE SALVAGED.

4. THE TECHNOLOGY CONTRACTOR SHALL TRACE AND LABEL ALL EXISTING CABLING WITHIN THE AREA OF DEMOLITION SCOPE OF WORK PRIOR TO

DISCONNECTION.

5. THE TECHNOLOGY CONTRACTOR SHALL IDENTIFY ALL CABLING AND SYSTEM COMPONENTS WHICH ARE TO REMAIN WITHIN THE AREA OF DEMOLITION SCOPE. THERE SHALL BE NO INTERRUPTION OF SERVICE TO ANY AREA OUTSIDE THE SCOPE LIMITS WITHOUT APPROVAL FROM THE OWNER'S REPRESENTATIVE. EXISTING EQUIPMENT TO REMAIN SHALL BE LEFT IN A CODE COMPLIANT MANNER.

6. THE TECHNOLOGY CONTRACTOR SHALL REMOVE ALL CABLING AND RACEWAYS TO THEIR POINTS OF ORIGIN WITHIN THE AREA OF DEMOLITION SCOPE. ITEMS IDENTIFIED FOR DEMOLITION SHALL NOT BE ABANDONED IN PLACE. RACEWAY THAT ENTER MASONRY WALLS OR FLOORS SHALL

BE CUT FLUSH AT THE SURFACE FOR PATCHING BY OTHERS.

7. THE TECHNOLOGY CONTRACTOR SHALL TEMPORARILY SUPPORT ALL LOW VOLTAGE CABLING AND ASSOCIATED ITEMS TO REMAIN THAT ARE AFFECTED BY DEMOLITION OF THE BUILDING STRUCTURAL COMPONENTS (WALL, CEILINGS, ETC.) TEMPORARY SUPPORTED ITEMS SHALL BE

PERMANENTLY SUPPORTED AND INSTALLED WHEN FINALIZED STRUCTURES ARE IN PLACE.

8. ALL REMOVED ITEMS SHALL BE LEGALLY DISPOSED OF UNLESS IDENTIFIED FOR USE. THE OWNER'S REPRESENTATIVE SHALL INSPECT ALL RETAINED ITEMS PRIOR TO PLACEMENT IN THE IDENTIFIED STORAGE LOCATION BY TECHNOLOGY CONTRACTOR.

9. COORDINATE WITH GENERAL, MECHANICAL, PLUMBING, AND ELECTRICAL CONTRACTORS FOR EXISTING EQUIPMENT TO BE REMOVED.

DISCONNECT AND REMOVE ANY TECHNOLOGY DEVICES PRIOR TO EQUIPMENT BEING REMOVED.

10. THE CONTRACTOR SHALL PROVIDE BLANK METAL PLATES FOR ALL JUNCTION/DEVICE BOXES NO LONGER IN USE.

11. ALL DEMOLITION AND CONSTRUCTION ACTIVITIES SHALL BE COORDINATED WITH THE GENERAL CONTRACTOR TO MINIMIZE DISRUPTION TO THE

NORMAL DAILY FUNCTIONING OF THE OCCUPIED.

12. ALL NON-ATTACHED ITEMS, SUCH AS MOBILE EQUIPMENT, DESKTOP PC OR PHONES SHALL BE REMOVED BY OWNER PRIOR TO

COMMENCEMENT OF DEMOLITION WORK.

13. UPON COMPLETION, CLEAN ALL AREAS AND REMOVE ALL DEMOLITION MATERIALS, CLEAN ALL ADJACENT AREA AFFECTED BY DEMOLITION.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :4

P

M

T.000

COMMUNICATIONS LEGEND

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

NOTE:

ALL WALL MOUNTED FACEPLATES SHALL BE MOUNTED ONTO A 4-11/16"x4-11/16"x2-1/8" DOUBLE GANG BACK BOX. EACH BACK BOX TO BE INSTALLED FLUSH TO FINISHED FACE OF WALL, FACEPLATES TO COMPLETELY COVER BACK BOX WITHOUT THE USE OF A TRIM RING. INSTALL A MIN. 1-1/4" CONDUIT FROM BACK BOX TO WITHIN 6" OF THE CABLE SUPPORT SYSTEM. PROVIDE PULL STRING WITHIN ALL TELECOMMUNICATIONS CONDUITS.

COMMUNICATIONS LEGEND

OUTLET, COMBINATION TELEPHONE/DATA

INSTALL (4) 8P8C MODULAR JACK INSERTS INTO (1) 4-PORT FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY 6 CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERTS AT UNUSED PORTS. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR

TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION.

OUTLET CEILING MOUNTED DATA FOR IP CAMERA

INSTALL (1) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SURFACE MOUNTED DEVICE BOX MOUNTED IN BACKBOX. INSTALL (1) DEDICATED UTP CATEGORY 6 RED CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERT IN ALL UNUSED PORTS. REFER TO SECURITY

SE-SERIES DRAWINGS FOR LOCATIONS AND DETAILS.

1. INSTALL CONDUIT RUNS IN THE MOST DIRECT ROUTE POSSIBLE WITH NO MORE THAN TWO 90 DEGREE

BENDS BETWEEN PULL POINTS OR PULL BOXES.

2. 90 DEGREE CONDUITS "LB" TYPE FITTINGS SHALL NOT BE USED FOR TELECOMMUNICATIONS CABLING

INSTALLATIONS.

3. CONTINUOUS CONDUIT SECTIONS OR SEGMENTS SHALL NOT BE GREATER THAN 100 LINEAR FEET IN

LENGTH WITHOUT AN ADEQUATELY SIZED PULL BOX - REFER TO DETAIL

4. CONDUITS SHALL BE BONDED TO GROUND ON ONE OR BOTH ENDS IN ACCORDANCE WITH NATIONAL

AND LOCAL REQUIREMENTS.

5. TELECOMMUNICATIONS CONDUITS SHALL BE INSTALLED TO WITHSTAND THE ENVIRONMENT IN WHICH THEY WILL BE EXPOSED AND IN ACCORDANCE WITH ANSI/NFPA-70; THE NATIONAL ELECTRICAL CODE.

6. THE TOTAL DISTANCE OF CONDUIT RUNS FOR TELECOMMUNICATIONS HORIZONTAL CABLE USE SHALL

NOT EXCEED 150 FEET.

7. DO NOT INSTALL CONDUITS OVER OR ADJACENT TO BOILERS, INCINERATORS, HOT WATER OR STEAM

LINES.

8. THE MINIMUM BEND RADIUS OF ANY PORTION OF THE CONDUIT PATHWAY SHALL BE SIX (6) TIMES THE

INTERNAL DIAMETER OF THE CONDUIT FOR ALL CONDUITS 2-INCHES IN DIAMETER OR LESS.

9. THE MINIMUM BEND RADIUS OF ANY PORTION OF THE CONDUIT PATHWAY SHALL BE TEN (10) TIMES THE INTERNAL DIAMETER OF THE CONDUIT FOR ALL CONDUITS WITH AN INTERNAL DIAMETER GREATER THAN

2-INCHES.

10. WHERE A CONDUIT RUN REQUIRES A REVERSE BEND (BETWEEN 100 DEGREES AND 180 DEGREES) A PULL BOX SHALL BE INSTALLED AT EACH BEND HAVING SUCH ANGLE, WITHIN 10 FEET OF THE BEND.

11. IF A CONDUIT RUN REQUIRES A THIRD 90 DEGREE BEND BETWEEN PULL POINTS OR PULL BOX, THE OVERALL DESIGN CAPACITY OF THE CONDUIT SYSTEM SHALL HAVE A DERATED TOTAL CAPACITY OF 15

PERCENT.

12. ALL CONDUIT ENDS SHALL BE REAMED AND FITTED WITH THREADED INSULATING BUSHING TO ELIMINATE

SHARP EDGES THAT CAN DAMAGE CABLES DURING INSTALLATION.

13. CONDUITS THAT PROTRUDE THROUGH WALLS AND FLOORS SHALL BE EXTENDED BEYOND THE SURFACE

PENETRATION TO WITHIN 12 INCHES OF THE CABLE TRAY OR CABLE RUNWAY SYSTEM.

14. ALL TELECOMMUNICATION OUTLETS STUB-UPS SHALL BE EQUIPPED WITH A PULL STRING WITH A

MINIMUM TEST RATING OF 200 LBS.

15. ALL INTERIOR COMMUNICATIONS CONDUITS GREATER THAN 1 1/2" CONDUITS SHALL BE EQUIPPED WITH 1/2" CABLE PULL STRING WITH 1250 LBS OF TENSILE STRENGTH AND SEQUENTIAL FOOTAGE MARKING.

16. ALL EXTERIOR COMMUNICATIONS CONDUITS SHALL BE EQUIPPED WITH 1/2" CABLE PULL STRING WITH

1250 LBS OF TENSILE STRENGTH AND SEQUENTIAL FOOTAGE MARKING.

17. INSTALL PULL BOXES IN ACCESSIBLE LOCATIONS. DIRECT ACCESS TO PULL BOXES IS REQUIRED.

PROVIDE LABELED, HINGED ACCESS PANEL DOOR. PULL BOXES SHALL BE LISTED FOR THE PURPOSE.

18. THE MINIMUM LENGTH OF PULL BOX SHALL BE 12 TIMES THE DIAMETER OF THE LARGEST CONDUIT. PULL

BOXES SHALL NOT BE USED IN SUBSTITUTION OF A 90 DEGREE BEND.

19. REFER TO ARCHITECTURAL DRAWINGS FOR MOUNTING ELEVATIONS.

20. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR COORDINATION OF ALL CONDUIT, RUNWAY, AND TRAY.

21. COORDINATE EXACT LOCATIONS OF ALL FLOOR BOXES AND POKE-THRU DEVICES WITH ARCHITECT

PRIOR TO INSTALLATION.

22. ALL OUTLET LOCATIONS AND DIMENSIONS ARE APPROXIMATE. COORDINATE EXACT MOUNTING LOCATION

AND HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO INSTALLATION.

23. WHERE CABLE TRAY RUNS ARE OBSTRUCTED, J-HOOKS MAY BE USED. J-HOOKS SHALL BE SPACED NO

LESS THAN 48" O.C AND NOT GREATER THAN 60" O.C. WHERE COMMUNICATIONS CABLE AND SECURITY CABLE FOLLOW THE SAME PATH, CABLES SHALL BE SEPARATED. ALL TELECOMMUNICATION OUTLETS SHOWN IN OPEN AIR ENVIRONMENT (I.E. MECHANICAL SPACE, PENTHOUSE, ROOF, GARAGE) SHALL BE

INSTALLED IN CONDUIT, RATED FOR THAT ENVIRONMENT.

24. ALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING SHALL BE INSTALLED IN MAIN AND

SECONDARY CORRIDORS ONLY FROM TELECOMMUNICATIONS ROOM TO WORK AREA OUTLETS.

25. ALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING SHALL ENTER WORK AREA ROOMS VIA PROPERLY SIZED CONDUIT ABOVE DOOR. CONDUIT SLEEVE SHALL BE PROPERLY FIRESTOPPED TO

MAINTAIN FIRE RATING.

26. UNDER NO CIRCUMSTANCES SHALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING BE

INSTALLED THROUGH ADJACENT ROOMS TO WORK AREA OUTLETS.

27. OUTLETS SHALL NOT BE LOCATED WITHIN 48 IN. OF THE "SWING OPEN" SIDE OF INWARD-OPENING

DOORS.

GENERAL PATHWAY REQUIREMENTS

FIBEROPTICS LINE = FO

TELEPHONE LINE = T

FO

T

TELEVISION OUTLET

INSTALL (1) RG6/RG11 COAXIAL CABLE TERMINATED ON 'F' CONNECTOR MODULAR INSERTS INTO (1) 1-PORT FACEPLATE. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR ADDITIONAL INFORMATION. DEVICES SHALL

TERMINATE IN FMS NETWORK ROOM.

TV

PATIENT TELEVISION OUTLET

INSTALL (1) RG6/RG11 COAXIAL CABLE TERMINATED ON 'F' CONNECTOR MODULAR INSERTS INTO (1) 1-PORT FACEPLATE. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. DEVICES SHALL TERMINATE IN FMS NETWORK ROOM.

PTV

CEILING MOUNTED DEVICE LEGEND

AV

OUTLET CEILING MOUNTED DATA FOR PROJECTOR

INSTALL (1) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SURFACE MOUNTED DEVICE BOX MOUNTED IN BACKBOX. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERT IN ALL UNUSED PORTS.

WAP

OUTLET CEILING MOUNTED DATA FOR WIRELESS ACCESS POINTS

INSTALL (1) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SURFACE MOUNTED DEVICE BOX MOUNTED IN BACKBOX. INSTALL (1) DEDICATED UTP CATEGORY 6 BLACK CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERT IN ALL UNUSED PORTS.

PUBLIC ADDRESS LEGEND

S ACT CEILING MOUNTED SPEAKER. - PROVIDE 18 AWG 2 CONDUCTOR SHIELDED CABLE DAISY CHAINED PER MANUFACTURER RECOMMENDATIONS FOR 70V AMPLIFIED SYSTEM. FIELD VERIFY EXISTING WIRING WITH VAMC TO CONNECT TO EXISTING AMPLIFIER HEADEND. PROVIDE ADDITIONAL HOME RUNS AS REQUIRED, NO MORE THAN (10) SPEAKERS PER HOME RUN. COORDINATE ADDITIONAL REQUIREMENTS WITH VAMC PRIOR TO START OF WORK.

Number: Revisions: Date:

CONFORMED CONSTRUCTION

DOCUMENTS

UP

DN

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

ABC

DEFGHI

IDENTIFY ALL TELECOMMUNICATIONS, WIRELESS

AND NETWORK OUTLETS AND DEMOLISH BACK TO

THEIR SOURCE PANELS IN THE TELECOM ROOMS,

UNLESS OTHERWISE NOTED.

EXISTING TELECOM ROOM

TO REMAIN

EXISTING SECURITY ROOM TO REMAIN

XM

XM

XM

XM

IDENTIFY SECURITY CONNECTIONS TO IT NETWORK

AND PROVIDE TEMPORARY RELOCATION.

GENERAL DEMOLITION NOTES:

1. REFER TO ARCHITECTURAL DRAWINGS FOR THE FULL EXTENT OF THE SCOPE OF WORK. THE TECHNOLOGY SCOPE OF WORK MAY EXTEND BEYOND THE AREA DEFINED BY THE ARCHITECTURAL DEMOLITION PLANS TO FULLY COMPLY WITH VARIOUS REQUIREMENTS

DEFINED BY THESE NOTES.

2. THE TECHNOLOGY DEMOLITION PLANS INDICATE THE GENERAL INTENT AND ARE NOT INTENDED TO SHOW ALL ITEMS TO BE REMOVED OR RETAINED. THE TECHNOLOGY CONTRACTOR SHALL VISIT THE SITE PRIOR TO THE SUBMISSION OF BIDS TO BECOME FAMILIAR WITH THE ACTUAL CONDITIONS AND EXTENT OF WORK. DEVICES AND EQUIPMENT LOCATED ON THE WALL AND/OR CEILING TO BE REMOVED SHALL BE DISCONNECTED AND MADE SAFE. THE TECHNOLOGY CONTRACTOR SHALL NOTIFY THE OWNER'S REPRESENTATIVE OF ANY

UNANTICIPATED HIDDEN CONDITIONS ENCOUNTERED DURING DEMOLITION.

3. THE TECHNOLOGY CONTRACTOR SHALL BE RESPONSIBLE FOR THE REPAIR OF ALL SYSTEMS OR BUILDING COMPONENTS DAMAGED DURING THE EXECUTION OF THE WORK. DAMAGE SHALL INCLUDE BUT NOT BE LIMITED TO DESTRUCTION OR DISPOSAL OF ITEMS

INTENDED TO REMAIN OR TO BE SALVAGED.

4. THE TECHNOLOGY CONTRACTOR SHALL TRACE AND LABEL ALL EXISTING CABLING WITHIN THE AREA OF DEMOLITION SCOPE OF WORK

PRIOR TO DISCONNECTION.

5. THE TECHNOLOGY CONTRACTOR SHALL IDENTIFY ALL CABLING AND SYSTEM COMPONENTS WHICH ARE TO REMAIN WITHIN THE AREA OF DEMOLITION SCOPE. THERE SHALL BE NO INTERRUPTION OF SERVICE TO ANY AREA OUTSIDE THE SCOPE LIMITS WITHOUT APPROVAL FROM THE OWNER'S REPRESENTATIVE. EXISTING EQUIPMENT TO REMAIN SHALL BE LEFT IN A CODE COMPLIANT MANNER.

6. THE TECHNOLOGY CONTRACTOR SHALL REMOVE ALL CABLING AND RACEWAYS TO THEIR POINTS OF ORIGIN WITHIN THE AREA OF DEMOLITION SCOPE. ITEMS IDENTIFIED FOR DEMOLITION SHALL NOT BE ABANDONED IN PLACE. RACEWAY THAT ENTER MASONRY

WALLS OR FLOORS SHALL BE CUT FLUSH AT THE SURFACE FOR PATCHING BY OTHERS.

7. THE TECHNOLOGY CONTRACTOR SHALL TEMPORARILY SUPPORT ALL LOW VOLTAGE CABLING AND ASSOCIATED ITEMS TO REMAIN THAT ARE AFFECTED BY DEMOLITION OF THE BUILDING STRUCTURAL COMPONENTS (WALL, CEILINGS, ETC.) TEMPORARY SUPPORTED ITEMS SHALL BE PERMANENTLY SUPPORTED AND INSTALLED WHEN FINALIZED STRUCTURES ARE IN PLACE.

8. ALL REMOVED ITEMS SHALL BE LEGALLY DISPOSED OF UNLESS IDENTIFIED FOR USE. THE OWNER'S REPRESENTATIVE SHALL INSPECT ALL RETAINED ITEMS PRIOR TO PLACEMENT IN THE IDENTIFIED STORAGE LOCATION BY TECHNOLOGY CONTRACTOR.

9. COORDINATE WITH GENERAL, MECHANICAL, PLUMBING, AND ELECTRICAL CONTRACTORS FOR EXISTING EQUIPMENT TO BE REMOVED.

DISCONNECT AND REMOVE ANY TECHNOLOGY DEVICES PRIOR TO EQUIPMENT BEING REMOVED.

10. THE CONTRACTOR SHALL PROVIDE BLANK METAL PLATES FOR ALL JUNCTION/DEVICE BOXES NO LONGER IN USE.

11. ALL DEMOLITION AND CONSTRUCTION ACTIVITIES SHALL BE COORDINATED WITH THE GENERAL CONTRACTOR TO MINIMIZE DISRUPTION

TO THE NORMAL DAILY FUNCTIONING OF THE OCCUPIED.

12. ALL NON-ATTACHED ITEMS, SUCH AS WIRELESS EQUIPMENT, DESKTOP PC OR PHONES SHALL BE REMOVED BY OWNER PRIOR TO

COMMENCEMENT OF DEMOLITION WORK.

13. UPON COMPLETION, CLEAN ALL AREAS AND REMOVE ALL DEMOLITION MATERIALS, CLEAN ALL ADJACENT AREA AFFECTED BY

DEMOLITION.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :4

P

M

T.102

COMMUNICATIONS DEMOLITION PLAN

LEVEL 2

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

NUMBERED NOTES:

IDENTIFY ALL WIRELESS ACCESS POINT CABLING AND PROTECT. WIRELESS LOCATIONS ARE EXISTING TO BE MAINTAINED AND WILL BECOME PART OF THE NEW CONTRUCTION1

Number: Revisions: Date:

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

CONFERENCE

OFFICE, MD

OFFICE,

DIRECTOR MD.

OFFICE, PD

TRAINING

OFFICE, SOCIAL

WORKER

CORRIDOR A

C200A

CLEAN

UTILITY/SUPPLY

EXAM ROOM

209STAFF LOUNGE

STAFF LOCKER

EMERG. ELECT.

TREATMENT

ROOM CORRIDOR

TEAM SPACE

TREATMENT #7

214I

BARI. TREATMENT

#2

214H

BARI. TREATMENT

#1

214GTREATMENT #1

214A

TREATMENT #2

214B TREATMENT #3

214C

TREATMENT #4

214D TREATMENT #5

214E

TREATMENT #6

214F

TREATMENT #8

214JTREATMENT #9

214K

TREATMENT #10

214LTREATMENT #11

214M

ISO TREATMENT

#1

PRIVATE

TREATMENT #1

ELECT.

EQUIPMENT

STORAGE

SOILED UTILITY

EQUIPMENT

PROCESSING,

CLEAN

PREP/STORE

CORRIDOR C

C200C

EXIST.

SOUTH STAIR

A-2-S

EXIST.

EAST STAIR

EXIST.

NORTH STAIR

EXIST. VESTIBULE

STERILE SUPPLY

OFFICE, DIETITIAN

PATIENT TOILET

CORRIDOR B

C200B-2

PATIENT

LOCKERS

STAFF TLT

STAFF TLT

OFFICE, FELLOW /

RN PD

NOURISHMENT

OFFICE, NURSE

MGR.

EQUIPMENT

PROCESSING,

SOILED

DIALYSATE PREP

WATER

TREATMENT

EQUIPMENT

REPAIR

MEDICATION

TV

TV

TV

TV

PTV

PTV

PTV

PTV

PTV PTV PTV PTV PTV PTV PTV

PTV PTV PTV PTV

XM

XM

XM

XM

WAP

WAP

WAP

WAP

WAP

WAP

WAP

WAP

WAP

WAP

WAP

WAP

PROVIDE 2" C. UNDER SLAB

TO CABLE TRAY. COORDINATE

WITH ARCHITECTURAL DRAWINGS

PROVIDE 2" C. UNDER SLAB

TO CABLE TRAY. COORDINATE

WITH ARCHITECTURAL DRAWINGS

AV

T.700

WAITING

FMS NETWORK CLOSET.

TERMINATE ALL CATV AND PAGING

EQUIPMENT.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :5

P

M

T.202

COMMUNICATIONS PLAN LEVEL 2

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

OUTLET COUNT SCHEDULE

OUTLET TYPE SUBSCRIPT DEVICE QUANTITY

DATA

PORTS

COAXIAL

PORTS PATCH PANEL COUNT

PROJ AV 1 1 0.02

WAP WAP 12 12 0.25

STANDARD 4 PORT - VOICE DATA 42 168 0 3.50

STANDARD MONITOR PTV 15 0 1 0.00

STANDARD TV TV 4 0 1 0.00

74 181 3.77

GENERAL NOTES:

1. COORDINATE FINAL LOCATION OF ALL WIRELESS ACCESS POINTS WITH PROVIDENCE VAMC IT DEPARTMENT. PROVIDE 10'-0" SERVICE COIL AT OUTLET LOCATION WITHIN 4'-0" OF FINAL LOCATION. REFER TO DETAILS FOR ADDITIONAL INFORMATION.

2. WIRELESS ACCESS POINTS IDENTIFIED WITH THE SUBSCRIPT 'XM' ARE EXISTING TO BE MAINTAINED THROUGHOUT THE PARTIAL DEMOLITION. COORDINATE RELOCATION AND/OR REMOVAL OF EXISTING WIRELESS ACCESS POINTS AND PROTECT CABLING FROM

DEMOLITION.

3. REFER TO ARCHITECTURAL DRAWINGS FOR ELEVATIONS OF ALL PATIENT TELEVISION COXIAL CABLE LOCATIONS, IDENTIFIED WITH

THE SUBSCRIPT 'PTV'. COORDINATE POWER REQUIREMENTS WITH ELECTRICAL CONTRACTOR.

4. REFER TO ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHTS OF ALL TELEVISIONS IDENTIFIED WITH THE SUBSCRIPT 'TV'.

Number: Revisions: Date:

S S S S

S S S S

S

S

S

S

S

SS

S

S

S

S

S

S

S

S

G

H

4.5

F5

W

Z

F E6

D1

E1

E2

E3

E4

EA

EB

EC

ED

EE

CC

I E D

X

Y

E-1.3

E-1.5

E-F

E-E

E-1

E-1.6

AA

X.5

FMS NETWORK CLOSET

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:4 :5

P

M

T.302

COMMUNICATIONS SPEAKER PLAN LEVEL

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

1/8" = 1'-0"

LEVEL 2 - PUBLIC ADDRESS

GENERAL NOTES:

1. ALL PAGING SPEAKERS LOCATED IN ACOUSTICAL CEILING TILES (ACT) SHALL BE BOGEN 2X2 DROP-IN CEILING SPEAKERS. MODEL NUMBER CSD2X2. PROVIDE 1X2 DROP-IN SPEAKERS WHERE COORDINATION IS REQUIRED, BOGEN CSD1X2

2. CONTRACTOR SHALL PROVIDE A NEW REMOTE PAGING AMPLIFIER. COORDINATE THE PATCHING AND INTEGRATION INTO THE EXISTING PAGING HEADEND LOCATED IN B-4. COORDINATE ALL WIRING AND CONNECTIONS WITH PROVIDENCE VAMC FACILITIES

DEPARTMENT PRIOR TO START OF WORK.

Number: Revisions: Date:

LA

B

E L

LA

B

E L

LA

B

E L

TYPICAL LABEL AREA

CATEGORY CABLE (TYPICAL) - SEE SPEC

PROVIDE LABELING PER

OWNER STANDARDS

TYPICAL CABLE LABEL

1-1/4" CONDUIT

DOUBLE GANG BOX

PROVIDE PULL STRING AT ALL

OUTLET LOCATIONS

CATEGORY 6

TRACJACK INSERT

LA

B

E L

A B

C D

RJ-45

8-PIN 8-CONDUCTOR PIN ASSIGNMENTS

R4T4R3T1R1T3R2T2

1 2 3 4 5 6 7 8

PAIR 2 PAIR 4PAIR 1

PAIR 3

W-O O W-G BL W-BL G W-BR BR

E1

EA

EXISTING NURSE CALL

SYSTEM.

EXISTING PATIENT

TELEVISION SYSTEM.

(3) 4" C. TO STAFF

BREAKROOM

ACCESSIBLE CEILING

T.700

NEW 2 POST EQUIPMENT RACK

NOTES:

1. THE NEW HEMODIALYSIS ADDITION SHALL UTILIZE THE EXISTING IT ROOM S222, BUILT AS PART OF THE ICU RENOVATION. COORDINATE

AVAILABLE RACK SPACE WITH PROVIDENCE VAMC PRIOR TO START OF WORK.

2. PROVIDE (3) 4" CONDUIT SLEEVES FROM THE IT ROOM INTO THE CEILING OF THE HEMODIALYSIS STAFF BREAK ROOM. COORDINATE CORE DRILLING THE STRUCTURAL PERIMETER BEAM WITH THE ARCHITECT PRIOR TO START OF WORK. PROVIDE FIRE STOPPING TO MAINTAIN FIRE

RATING OF ALL WALLS.

3. PROVIDE BONDING JUMPER FROM EXISTING TELECOMMUNICATION GROUND BAR TO NEW CONDUIT SLEEVES.

LEVEL 2

11' - 11"

LEVEL 2

11' - 11"

LEVEL 3

23' - 10"

LEVEL 3

23' - 10"

EXISTING RACKS

EXISTING VERTICAL

WIRE MANAGERS

EXISTING FIBER CONNECTIONS

EXISTING COPPER CONNECTIONS

EXISTING 'A' CONNECTIONS

(18 FREE PORTS)

EXISTING 'B' CONNECTIONS

(18 FREE PORTS)

EXISTING 'C' CONNECTIONS

(18 FREE PORTS)

EXISTING 'D' CONNECTIONS

(18 FREE PORTS)

EXISTING WIRELESS CONNECTIONS

NEW 'A' CONNECTIONS

FUTURE 'A' CONNECTIONS

NEW 'B' CONNECTIONS

FUTURE 'B' CONNECTIONS

NEW 'C' CONNECTIONS

FUTURE 'C' CONNECTIONS

NEW 'D' CONNECTIONS

FUTURE 'D' CONNECTIONS

NEW WIRELESS CONNECTIONS

FUTURE WIRELESS CONNECTIONS

NEW 2 POST EQUIPMENT RACK

NOTES:

1. STANDARD DROP PATCH PANELS SHALL BE ORTRONICS UTP CAT6 MODELS OR-851000334. THE CONTRACTOR SHAL PROVIDE FOUR DIFFERENT COLOR CABLES FOR EACH WORKSTATION OUTLET AS FOLLOWS A=YELLOW, B=BLUE, C=GREEN AND D=WHITE. EACH CABLE WITHIN THE WORKSATION OUTLET SHALL TERMINATE ON ITS OWN DEDICATED PATCH PANELS IDENTIFIED AS EITHER A, B, C OR D.

2. THE CONTRACTOR SHALL SUPPLY ONE PATCH CORD FOR EACH CABLE TERMINATED AT THE PATCH PANEL. THE PATCH CORDS SHALL

MATCH THE COLOR OF THE ASSOCIATED HORIZONTAL CABLE AND CAT 6 JACK.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:5 :0

P

M

T.700

COMMUNICATIONS DETAILS

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

N.T.S.

STANDARD 4-PORT TRACJACK OUTLET

N.T.S.

T568B WIRING SCHEME

NOTES:

1. THE CONTRACTOR SHALL PROVIDE FOUR DIFFERENT COLOR CABLES FOR EACH WORKSTATION OUTLET AS FOLLOWS A=YELLOW, B=BLUE, C=GREEN AND D=WHITE. EACH CABLE WITHIN THE WORKSATION OUTLET SHALL TERMINATE ON A MODULAR JACK OF THE SAME COLOR AS

THE CABLE.

Number: Revisions: Date:

1/2" = 1'-0"

LEVEL 2 - IT ROOM PART PLAN

1/2" = 1'-0"

LEVEL 2 - IT ROOM RACK ELEVATIONS

TYPICAL MESH TYPE STEEL

CABLE TRAY DISTRIBUTION SYSTEM

1/2" DIAMETER THREADED ROD

THREADED ROD (CABLE) PROTECTOR TO

EXTEND UP 6" FROM BOTTOM OF TRAY

HEAVY DUTY

SUPPORT CHANNEL EVERY 60"

CONDUIT CONNECTOR

1" CONDUIT FROM WORK AREA OUTLET

1/2" DIAMETER THREADED

ROD & FINNED NUT

S

ID

E R

A

IL

S E

E P

LA

N

TYPICAL HOLD DOWN PLATE

HEAVY DUTY SUPPORT CHANNEL

7/16"

7/

"T" INTERSECTION

SHALL BE A RADIUS

CABLE TRAY SECTION

90° SHALL BE

A RADIUS CABLE

TRAY SECTION

CABLE TRAY "T" SECTION CABLE TRAY 90° SECTION

MESH TYPE CABLE TRAY

APPROVED

ANCHOR BOLT

THREADED ROD

PROTECTOR

TYPICAL HOLD

DOWN PLATE

1/2" DIAMETER

THREADED ROD

& FINNED NUT

HEAVY DUTY

SUPPORT CHANNEL

CEILING SLAB

TYPICAL MESH TYPE STEEL

CABLE TRAY DISTRIBUTION SYSTEM

1/2" DIAMETER THREADED ROD

THREADED ROD (CABLE) PROTECTOR TO

EXTEND UP 6" FROM BOTTOM OF TRAY

HEAVY DUTY

SUPPORT CHANNEL EVERY 60"

ISOMETRIC VIEW

INACCESSIBLE CEILING OR SOFFIT AREA

CONDUIT WITH PULL STRING TO ABOVE

ACCESSIBLE CEILING BY E.C.

PARTITION WALL

DEVICE BOX

ACCESSIBLE CEILING

FINISHED FLOOR

CEILING SLAB OR SUPPORT

TYPICAL COMMUNICATIONS FACEPLATE

HORIZONTAL DISTRIBUTION CABLE FROM

WORK AREA OUTLET TO NEAREST IDF ROOM

1. AT ALL RECEPTACLES, CONDUIT SHALL BE INSTALLED

FROM EACH DEVICE BACKBOX TO NEAREST ACCESSIBLE

CEILING AREA CONTAINING A CABLE SUPPORT SYSTEM.

CABLE ROUTED ABOVE INACCESSIBLE OR "HARD"

CEILINGS SHALL BE INSTALLED IN CONDUIT.

GENERAL NOTES:

C O

O R

D

IN

A T

E W

IT

H

A R

C H

IT

E

C

TU

R A

L D

R A

W

IN

G S

TERMINATE CONDUIT WITHIN 6" OF CABLE TRAY

TYPICAL CABLE TRAY

THREADED, INSULATED BUSHING (TYPICAL)

TYPICAL WIDE BASE, J-

HOOK CABLE MANAGEMENT

(SEE SPEC)

FASTENER NUT

1/4" THREADED ROD

ANCHOR BRACKET

CABLE MANAGEMENT TIE (TYPICAL

ALL J-HOOKS)

STRUCTURE ABOVE

ACCESSIBLE CEILING

NOTES:

1. J-HOOKS SHALL BE MOUNTED EVERY 48" to 60"; O.C. MINIMUM AND ACCESSIBLE AT ALL TIMES. MAINTAIN MINIMUM OF

6" OF CLEARANCE FROM CEILING TILES AND OTHER OBSTRUCTIONS.

2. J-HOOK PATHWAY MUST BE CONTINUOUS. ALL J-HOOKS SHALL BE MOUNTED ABOVE CEILING AT AN ACCESSIBLE

AREA. AREAS THAT ARE NOT ACCESSIBLE SHALL TRANSITION TO A CONDUIT PATHWAY.

3. MALLEABLE BEAM CLAMP METHOD OF HANGING J-HOOKS SHALL BE ACCEPTED WHEN HANGING OFF OF STRUCTURAL

STEEL ONLY.

4. DO NOT MOUNT J-HOOKS TO SUPPORT BEAMS OR STRUCTURES THAT HAVE SPRAYED-ON FIRE PROOFING MATERIAL.

MOUNTING SUPPORT HOOKS MUST NOT DISTURB THE FIRE RATING OF ANY STRUCTURE.

CONDUIT SLEEVE - SEE PLANSFIRE BARRIER CAULK

MINERAL WOOL PACKING

TELECOMUNICATIONS SYSTEM

CABLING - IE. FIBER OPTICS, INNER

DUCT OR CATEGORY CABLES

FLOOR SYSTEM - SEE

ARCHITECTURAL

DRAWINGS

FIRE AND SMOKE PROOFING GENERAL NOTES

1. CONTRACTOR SHALL PROVIDE FIRESTOPPING SYSTEM THROUGH PENETRATIONS SUCH THAT ALL PENETRATION RESTORE THE

REQUIRED FIRE AND SMOKE RATING REQUIRED BY THE ARCHITECT.

2. ALL PENETRATIONS THROUGH FIRE OR SMOKE RATED WALLS AND FLOORS SHALL BE FIRESTOPPED WITH APPROVED METHODS TO

REDUCE THE CHANCE OF SPREADING FIRE AND/OR SMOKE.

3. DETAILS ARE DIAGRAMMATIC IN NATURE AND ARE FOR REFERENCE ONLY. CONSULT UNDERWRITERS LABORATORIES, INC., "FIRE

RESISTANCE DIRECTORY" FOR FORMAL DETAILS.

4. USE ONLY AN ENGINEERED AND APPROVED SYSTEM TO FIRESTOP ALL PENETRATIONS.

5. INSTALL FIRESTOPPING MATERIAL IN ACCORDANCE TO MANUFACTURER'S TESTED METHOD.

6. INSTALL FIRESTOPPING INSIDE SLEEVES AFTER CABLE INSTALLATION.

7. ALWAYS RESTORE THE FIRE RATING OF THE WALL TO THE INTENDED DESIGN.

FIRE RATED GYPSUM

WALLBOARD ASSEMBLY

EMT CONDUIT SLEEVE

PATHWAY

FIRESTOPPPING MATERIAL

(TYPICAL)

WOOD OR STEEL STUD

CONSTRUCTION

DIAMETER VARIES - REFER TO PLANS

FIRE AND SMOKE PROOFING GENERAL NOTES

1. CONTRACTOR SHALL PROVIDE FIRESTOPPING SYSTEM THROUGH PENETRATIONS SUCH THAT ALL PENETRATION RESTORE THE REQUIRED

FIRE AND SMOKE RATING REQUIRED BY THE ARCHITECT.

2. ALL PENETRATIONS THROUGH FIRE OR SMOKE RATED WALLS AND FLOORS SHALL BE FIRESTOPPED WITH APPROVED METHODS TO

REDUCE THE CHANCE OF SPREADING FIRE AND/OR SMOKE.

3. DETAILS ARE DIAGRAMMATIC IN NATURE AND ARE FOR REFERENCE ONLY. CONSULT UNDERWRITERS LABORATORIES, INC., "FIRE

RESISTANCE DIRECTORY" FOR FORMAL DETAILS.

4. USE ONLY AN ENGINEERED AND APPROED SYSTEM TO FIRESTOP ALL PENETRATIONS.

5. INSTALL FIRESTOPPING MATERIAL IN ACCORDANCE TO MANUFACTURER'S TESTED METHOD.

6. INSTALL FIRESTOPPING INSIDE SLEEVES AFTER CABLE INSTALLATION.

7. ALWAYS RESTORE THE FIRE RATING OF THE WALL TO THE INTENDED DESIGN.

Project TitleDrawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT STAMPCONSULTANTS

321 4 5 6 7 8 9 10

CIVIL:

Pare Corporation 8 Blackstone Valley Place Lincoln, RI 02865

Phone: 401-334-4100 Facsimile: 401-334-4108

CONFORMED CONSTRUCTION DOCUMENTS

290 Congress St., 5th Floor Boston, MA 02210

Phone: 617-895-1000

VA Medical Center Providence, RI Expand Bldg. 1 to Replace Hemodialysis Phase 1

Providence, RI

650-342

Project Director

FULLY SPRINKLERED

STRUCTURAL:

Odeh Engineers 1223 Mineral Springs Ave.

Providence, RI 02904

Phone: 401-724-1771 Facsimile: 401-724-1981

MEP/FP:

BR+A Consulting Engineers, LLC 10 Guest St. 4th Floor Boston, MA 02135

Phone: 617-254-0016 Facsimile: 617-924-9339

COST:

DG Jones International, Inc.

3 Baldwin Green Common, Suite 202 Woburn, MA 01801

Phone: 781-982-3131 Facsimile: 781-932-3199

Location

Issue Date Checked Drawn

Project Number

Building Number

Drawing Number

C R e v it \T

E C

H

V A

P R

O V

V

H

S h o ja i@ b rp lu s a .c o m

.r v t

/5

/2

:5 :0

P

M

T.701

COMMUNICATIONS DETAILS

11/09/2018 JJL JJL

100% CONSTRUCTION

DOCUMENTS

N.T.S.

TYPICAL WIRE BASKET CONDUIT CONNECTION DETAIL

12" = 1'-0"

TYPICAL WIRE BASKET DETAILS

12" = 1'-0"

WALL DEVICE DETAIL

12" = 1'-0"

TYPICAL WIDE AREA J-HOOK DETAIL

N.T.S.

TYPICAL VERTICAL CONDUIT FIRESTOPPING DETAIL

N.T.S.

TYPICAL HORIZONTAL CONDUIT FIRESTOPPING DETAIL

Number: Revisions: Date: