36C25522Q0300.docx

36C25522Q0300

PAGE 1 OF

1. REQUISITION NO.

2. CONTRACT NO.

3. AWARD/EFFECTIVE DATE

4. ORDER NO.

5. SOLICITATION NUMBER

6. SOLICITATION ISSUE DATE

a. NAME

b. TELEPHONE NO. (No Collect Calls)

8. OFFER DUE DATE/LOCAL

TIME

9. ISSUED BY

CODE

10. THIS ACQUISITION IS

UNRESTRICTED OR

SET ASIDE:

% FOR:

SMALL BUSINESS

HUBZONE SMALL

BUSINESS

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

WOMEN-OWNED SMALL BUSINESS

(WOSB) ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

EDWOSB

8(A)

NAICS:

SIZE STANDARD:

11. DELIVERY FOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

12. DISCOUNT TERMS

13a. THIS CONTRACT IS A

RATED ORDER UNDER

DPAS (15 CFR 700)

13b. RATING

14. METHOD OF SOLICITATION

RFQ

IFB

RFP

15. DELIVER TO

CODE

16. ADMINISTERED BY

CODE

17a. CONTRACTOR/OFFEROR

CODE

FACILITY CODE

18a. PAYMENT WILL BE MADE BY

CODE

TELEPHONE NO.

UEI:

EFT:

PHONE:

FAX:

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER 18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW IS CHECKED

SEE ADDENDUM

19.

20.

21.

22.

23.

24.

ITEM NO.

SCHEDULE OF SUPPLIES/SERVICES

QUANTITY

UNIT

UNIT PRICE

AMOUNT

(Use Reverse and/or Attach Additional Sheets as Necessary)

25. ACCOUNTING AND APPROPRIATION DATA

26. TOTAL AWARD AMOUNT (For Govt. Use Only) 27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA

ARE

ARE NOT ATTACHED.

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA

ARE

ARE NOT ATTACHED

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN _______________

29. AWARD OF CONTRACT: REF. ___________________________________ OFFER

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND

DATED ________________________________. YOUR OFFER ON SOLICITATION

DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY

(BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE

ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED

SET FORTH HEREIN IS ACCEPTED AS TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER) 30b. NAME AND TITLE OF SIGNER (TYPE OR PRINT) 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (TYPE OR PRINT) 31c. DATE SIGNED

AUTHORIZED FOR LOCAL REPRODUCTION

(REV. NOV 2021)

PREVIOUS EDITION IS NOT USABLE

Prescribed by GSA - FAR (48 CFR) 53.212

7. FOR SOLICITATION

INFORMATION CALL:

STANDARD FORM 1449

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

589-22-3-7507-0048 36C25522Q0300 05-19-2022 Ballentos, Emilio emilio.ballentos@va.gov 913-946-1981 06-03-2022 11am

CDT

36C255 Department of Veterans Affairs Network Contracting Office (NCO) 15 3450 S 4th Street Trafficway Leavenworth KS 66048 X X 238210 $16.5 Million N/A X Department of Veterans Affairs Robert J. Dole VA Medical Center 5500 E. Kellogg Avenue Wichita KS 67218-1607 36C255 Department of Veterans Affairs Network Contracting Office (NCO) 15 3450 S 4th Street Trafficway Leavenworth KS 66048

36C255 Department of Veterans Affairs Financial Services Center http://www.fsc.va.gov/einvoice.asp Austin TX 877-353-9791 512-460-5429 See CONTINUATION Page Electrical Inspection - Wichita VAMC In Accordance with the Statement of Work ******** See Section B for details ******** This will result in a Firm Fixed Price, FOB Destination This solicitation is intended as Small Business Set Aside.

FAR 4.11 states that prospective contractors shall be registered in the System for Award Management (www.SAM.gov) database.

WD - 2015-53415, Rev. 2 applies – See Section D for Details See Offeror's Instruction in Section E.2 and attached Line 1 Schematics Site visit is available for May 24, 2022, at 10:00am - 12:00pm Central Time Zone. See Section E.2 See CONTINUATION Page X X Ballentos, Emilio Contracting Officer Table of Contents

SECTION B - CONTINUATION OF SF 1449 BLOCKS

B.1 CONTRACT ADMINISTRATION DATA

(Continuation from Standard Form 1449, block 18A.)

1. Contract Administration: All contract administration matters will be handled by the following individuals:

a. CONTRACTOR: NAME: ___________________________________

SAM UEI #: __________________________________

b. GOVERNMENT: CONTRACTING OFFICER 36C255

DEPARTMENT OF VETERANS AFFAIRS

NETWORK CONTRACTING OFFICE (NCO) 15

3450 S 4th STREET

LEAVENWORTH, KS 66048

2. CONTRACTOR REMITTANCE ADDRESS: All payments by the Government to the contractor will be made in accordance with:

[X] 52.232-33, Payment by Electronic Funds Transfer—System for Award Management

3. INVOICES: Invoices shall be submitted:

[X] Upon Completion of Service [ ] Other

4. GOVERNMENT INVOICE ADDRESS: All Invoices from the contractor shall be submitted electronically in accordance with VAAR Clause 852.232-72 Electronic Submission of Payment Requests.

Department of Veterans Affairs Financial Services Center http://www.fsc.va.gov/einvoice.asp

ACKNOWLEDGMENT OF AMENDMENTS: The offeror acknowledges receipt of amendments to the Solicitation numbered and dated as follows:

36C25522Q0300

Page 1 of Page 1 of

B.2. STATEMENT OF WORK

PROFESSIONAL TESTING AND MAINTENANCE OF ELECTRICAL SYSTEMS AND EQUIPMENT

GENERAL:

Working Hours outages shall be scheduled and approved in writing at least two weeks in advance. Outages will be scheduled only at night and on weekends for certain facility such as Surgery, endoscopy, MRI, PET/CT, etc..

SCOPE 2.1 THREE YEAR ELECTRICAL SYSTEM MAINTENANCE AND TESTING.

2.2 Switchgear equipment. Medium Voltage Circuit Breakers and Protective Relays.

2.2.1 Record switchgear, breaker and device nameplate information and compare with the facility's one-line diagram, when available. Identify and record discrepancies.

device' for pickup at 200% and 300' of its rating and for instantaneous pickup. Clean and dress all contact surfaces and lubricate as necessary

3.1.2.3 Presence of external fields.

3.2.3.1 Field instruments: Analog-6 months maximum: Digital-12 months maximum. 3.2.3.2 Laboratory instruments: 12 months.

3.2.3.3 Leased specialty equipment: 12 months (Where accuracy is guaranteed by lessor).

3.2.4 Dated calibration labels shall be visible on all test equipment. -

3.2.5 Records, which show date and results of instruments calibrated or tested, must be kept up-to-date.

3.2.6 Up-to-date instrument calibration instructions and procedures shall be maintained for each test instrument.

3.2.7 Calibrating standard shall be of higher accuracy than that of the instrument tested.

3.3.1.2 Description of equipment tested.

3.3.1.3 Description of test.

3.3.1.4 Test results.

4.1.1.5.1 Closure attempt shall be made on locked open devices. Opening attempt shall be made on locked closed devices.

4.1.1.5.2 Key exchange shall be made with devices operated in off-normal positions.

4.1.2.1 Perform ground resistance tests in accordance with Section 4.8.

4.1.2.5.1 Inspect for physical damage, cracked insulation, broken leads, tightness of connections, defective wiring, and overall general condition.

4.1.2.5.2 Verify that primary and secondary fuse ratings or circuit breakers match drawings.

4.1.2.5.3 Perform insulation resistance test. Measurements shall be made from winding-to-winding and windings-to-ground. Test voltages and minimum resistances shall be in accordance with Table 4.2.1. Results to be temperature corrected in accordance with Table 4.2.2.

4.1.3 Test values

TABLE 4.1.1

Switchgear Insulation Resistance Test Voltage

dc Test Voltage Recommended Minimum Insulation Resistance In Megohms

TABLE 4.1.2

Field Overpotential Test Voltages* Maximum

ac de

+Consult Manufacturer Derived from ANSI/IEEE 037.20.2, Paragraph 5.5 and C37.20.3, paragraph 5.5

4.2 Transformers

4.2.1 Transformers-Dry Type

4.2.1.1 Visual and Mechanical Inspection

4.2.1.1.1 Inspect for physical damage, cracked insulators, lightness of connections, defective wiring and general mechanical and electrical conditions.

4.2.1.1.2 Verify proper auxiliary device operation such as fans and indicators.

4.2.1.1.3 Check tightness of accessible bolted electrical joints in accordance with Table 7.1.

4.2.1.1.4 Perform specific inspections and mechanical tests as recommended by manufacturer.

4.2.1.1.5 Make a close examination for shipping brackets or fixtures that may not have been removed during original installation. Ensure resilient mounts are free.

4.2.1.1.6 Verify proper core grounding. 4.2.1.1.7 Verify proper equipment grounding.

4.2.1.1.8 Thoroughly clean unit prior to testing unless "as found" and "as left" tests are required.

4.2.1.2 Electrical Tests

4.2.1.2.1 Perform insulation resistance tests, winding to-winding and windings-to-ground, utilizing a megohmmeter with test voltage output as shown in Table 4.2.3.

4.2.2.1 Visual and Mechanical Inspection.

4.2.1.2.1.1 Test duration shall be for 10 minutes with resistances tabulated at 30 seconds, 1 minute, and 10 minutes. Dielectric absorption ratio and polarization index will be calculated.

4.2.1.2.1.2 Perform tests and adjustments for fans, controls, and alarm functions.

4.2.1.2.1.3 Verify that tap-changer is set at specified ratio.

4.2.1.2.1.4 Verify proper secondary voltage phase-to-phase and phase-to-neutral after energization and prior to loading.

4.2.1.3 Test Values

4.2.1.3.1 Insulation resistance test values should not be less than values recommended in Table 4.2.3 Results shall be temperature corrected in accordance with Table 4.2.4.

4.2.2 Transformers - Liquid Filled

4.2.2.1 Visual and Mechanical Inspection

4.2.2.1.1 Inspect for physical damage, cracked insulators, leaks, tightness of connections, and general mechanical and electrical conditions.

4.2.2.1.2 Verify proper auxiliary device operation.

4.2.2.1.3 Check tightness of accessible bolted electrical connections in accordance with Table 7.1.

4.2.2.1.4 Verify proper liquid level in all tanks and bushings.

4.2.2.1.5 Perform specific inspections and mechanical tests as recommended by manufacturer.

4.2.2.1.6 Verify proper equipment grounding.

4.2.2.2 Electrical Tests

4.2.3.1 Insulation resistance and absorption test. Test voltages to be in accordance with Table 4.2.3. Resistance values to be temperature corrected in accordance with Table 4.2.4.

TABLE 4.2.1

Distribution

4.2.3.7 Dielectric fluid should comply with Table 4.2.2.

4.2.3.8 Winding resistance test results should compare within one percent (1%) of adjacent windings.

TABLE 4.12

Hydrocarbon Dielectric

Dielectric Breakdown ASTM D-1816 @0.04" gap

34.5 kV and

above

Tension ASTM D-974 Minimum Minimum or D-2285

Visual

Power

Q25 degrees

Water Con tent ASTM

below above 15

*Or in accordance with manufacturer's requirements. Some manufacturers recommend 15 PAM maximum for all transformers.

Note: The values for oil are taken from ANSI C57.106 (IEEE Std. 64). The remaining values are acceptance test values and should be modified for service aged fluid as recommended by the manufacturer.

4.2.4.2 Thoroughly clean unit prior to making any tests.

4.2.4.3 Perform insulation resistance test. Calculate dielectric absorption ratio and polarization index. Measurements shall be made from winding-to-winding and windings-to-ground. Test voltages and minimum resistance shall be in accordance with Table 4.2.3. Results to be temperature corrected in accordance with Table 4.2.4.

TABLE 4.2.3

Transformer Insulation Resistance Test Voltage Recommended

TABLE 4.2.4

Correction Factors to 20 degrees C

TEMPERATURE

DRY

4.3 Cables

4.3.1 Cables - Low Voltage - 600V Maximum

4.3.1.1 Visual and Mechanical Inspection

4.3.1.1.1 Inspect exposed sections of cables for physical damage.

4.3.1.1.2 Test cable mechanical connections to manufacturer's recommended values with a calibrated torque wrench. In lieu of above torquing, perform infrared survey in accordance with Section 6.

4.3.1.2 Electrical Tests

4.3.1.2.1 Perform insulation resistance test on each conductor with respect to ground and adjacent conductors. Applied potential to be 1000 volts do for 1 minute.

4.3.1.3 Test Values

4.3.1.3.1 Minimum insulation resistance values shall be not less than two megohms.

4.3.2 Cables - Medium Voltage - 69 kV Maximum

4.3.2.1 Visual and Mechanical Inspection

4.3.2.1.1 Inspect exposed sections for physical damage.

4.3.2.2 Electrical Tests

4.3.2.2.1 Perform a shield continuity test on each power cable. Ohmic value shall be recorded.

4.3.2.2.2.2 Record wet and dry bulb temperatures of relative humidify end temperature.

4.3.2.2.2.3 Test each section of cable individually.

4.3.2.2.2.4 Individually test each conductor with all other conductors grounded. Ground all shields.

TABLE 4.3.1

Maximum Maintenance Test Voltages (kV,dc) 1968 and Later Cable Rated

Elastomeric:

Elastomeric:

Derived from ANSI/IEEE std. 141-1986 Table 82 Note: Selection of test voltage for in-service cables depends on many factors. The owner should be consulted and/or informed of the intended test voltage prior to performing the test. The above tables are consistent with ILEA recommendations. AE1C C55 and C56, and ANSI/WEE Std. 400 specify higher voltages. It the cable fails during the test it will require repair or replacement prior to re-energizing.

4.3.2.3 Test Values

4.3.2.3.2.1 The step voltage slope should be reasonably linear.

4.3.2.3.2.2 Absorption slope should be flat or negative. In no case should slope exhibit a positive characteristic.

4.3.2.3.2.3 compare test results to previously obtained results.

4.4 Metal Enclosed Busways

4.4.1 Visual and Mechanical Inspection

4.4.1.1 Inspect bus for physical damage.

4.4.1.2 Inspect for proper bracing, suspension alignment, and enclosure ground.

4.4.2 Electrical Tests

4.4.2.1 Measure insulation resistance of each bus run phase-to-ground for one (1) minute.

4.4.3 Test Values

4.4.3.1 Bus bolt torque values shall be in accordance with manufacturer's recommendations or Table 8.1.

4.4.3.2 Insulation resistance test voltages and resistance values shall be in

4.5.1 Visual and Mechanical Inspection

4.5.1.1 Inspect for physical and mechanical condition.

4.5.1.5 Check blade alignment and arc interrupter operation.

4.5.1.6 Verify that expulsion limiting devices are in place on all holders having expulsion type elements.

4.5.1.7 Check each fuse holder for adequate mechanical support for each fuse.

4.5.1.8 Inspect all bus connections for tightness of bolted bus joints by calibrated torque wrench method. Refer to manufacturer's instructions or Table 8.1 for proper torque levels. In lieu of above torque tests, perform infrared survey in accordance with Section 6.

4.5.1.9 Test all electrical and mechanical interlock systems for proper operation and sequencing.

4.5.1.10 Clean entire switch using approved methods and materials. 4.5.1.11 Verify proper phase barrier materials and installation.

4.5.1.12 Lubricate as required.

4.5.1.13 Check switch blade clearances with manufacturer's published data. 4.5.1.14 Inspect all indicating devices for proper operation.

4.5.2 Electrical Tests

4.5.2.1 Perform insulation resistance tests on each pole, phase-to-phase and phase-to- ground for one (1) minute. Test voltage and minimum resistances should be in accordance with Table 8.2. In lieu of this test, perform appropriate insulation tests in conjunction with medium voltage cable insulation tests and/or power transformer primary winding tests.

4.5.2.2 Perform contact resistance test across each switch blade and fuse holder.

4.5.3 Test Values

4.5.4.1.3 Check blade alignment and arc interrupter operation.

4.5.4.1.4 Check fuse link or element and holder for proper current rating.

4.5.4.2 Electrical Tests

4.5.4.2.1 Perform ac or do overpotential test on each

pole-to-ground and pole-to-pole.

4.5.4.2.2 Perform contact resistance teat across each switch blade.

4.5.4.3 Test Values

4.5.4.3.1 Apply overpotential test voltages in accordance with Table 4.1.6.

4.6.1 Circuit Breakers-Low Voltage

4.6.1.1 Circuit Breakers-Low Voltage-Insulated Case

4.6.1.1.1 Visual and Mechanical Inspection

4.6.1.1.1.1 Check circuit breaker for proper mounting.

4.6.1.1.1.2 Operate circuit breaker to ensure smooth operation.

4.6.1.1.1.3 Inspect case for cracks or other defects .

4.6.1.1.1.4 Check tightness of connections with calibrated torque wrench. Refer to manufacturer's instructions or Table 8.1 for proper torque levels. In lieu of this test, perform infrared survey in accordance with Section 6.

4.6.1.1.1.5 Check internals on unsealed units. 4.6.1.1.2 Electrical Tests

4.6.1.1.2.1 Perform a contact resistance test.

4.6.1.1.2.4 Determine short time pickup and delay by primary current injection.

4.6.1.1.2.5 Determine ground fault pickup and time delay by primary current injection.

4.6.1.1.3 Test Values

4.6.1.1.3.1 Compare contact resistance or millivolt drop values to adjacent poles and similar breakers. Investigate deviations of more than fifty (50%). Investigate any value exceeding manufacturer's recommendations.

4.6.1.1.3.2 Insulation resistance shall not be less than 100 megohms.

4.6.1.1.3.5 Instantaneous pickup values shall be within values shown on Table 4.6.1.2.

TABLE 4.6. 1.1

Values for Overcurrent Trip Test (At 300% of Rated Continuous Current of Circuit Breaker)

Continuous Current Amperes Maximum Trip Time in seconds*

*For integrally-fused circuit breakers, trip times may be substantially longer if tested with the fuses replaced by solid links (shorting bars)

TABLE 4.6.1.2

Instantaneous Trip Setting Tolerances Tolerances of High and Low Settings

4.7 Circuit Breakers-Medium Voltage

4.7.1 Circuit Breakers-Medium Voltage-Air

4.7.1.1 Visual and Mechanical Inspection

4.7.1.1.1 Inspect for physical damage, cleanliness, and adequate lubrication.

4.7.1.1.2 Inspect anchorage, alignment, and grounding.

4.7.1.1.5 Check cell fit and element alignment. 4.7.1.1.6 Check racking mechanism.

4.7.1.1.7 Verify that primary and secondary contact wipe and other dimensions vital to satisfactory operation of the breaker are correct.

4.7.1.1.8 Ensure that all maintenance devices are available for servicing and operating the breaker.

4.7.1.1.9 Lubricate all moving current carrying parts.

4.7.1.1.10 Check for proper operation of the cubicle shutter. 4.7.1.2 Electrical Tests

4.7.1.2.1 Measure contact resistance.

4.7.1.2.2 Measure insulation resistance pole-to-pole, pole-to-wound, and across open poles. Use a minimum test voltage of 2500 volts.

*4.7.1.2.3 Perform insulation resistance test at 1000 volt. do on all control wiring. (Do not perform the test on wiring connected to solid state components).

4.7.1.2.4 With breaker in the test position, make the following tests: 4.7.1.2.4.1 Trip and close breaker with the control switch.

4.7.1.2.4.2 Trip each breaker by operating manually each of its protective relays.

4.7.1.3 Test Values

4.7.1.3.1 Determine contact resistance in microohm’s. Investigate deviations of more than 50%.

4.7.1.3.2 Minimum insulation resistance should comply with Table 4.1.1.

4.7.1.3.3 Power factor and arc chute watts lost should be compared with results from previous tests of similar breakers, or referred to manufacturer's published data.

4.7.2 Circuit Breakers-Medium Voltage-Oil

4.7.2.1 Visual and Mechanical Inspection

4.7.2.1.1 Inspect for physical damage.

4.7.2.1.2 Inspect anchorage, alignment, and grounding.

4.7.2.1.3 Perform all mechanical operation and contact alignment tests on both the circuit breaker and its operating mechanism.

4..8 Metering and Instrumentation

4.8.1 Visual and Mechanical Inspection

4.8.1.1 Examine all devices for broken parts and wire connection tightness. 4.8.2 Electrical Tests

4.8.2.1 Check calibration of meters at all cardinal points.

4.8.2.2 Calibrate watt hour meters to one half of one percent (0.5%).

4.8.2.3 Verify all instrument multiplier-.

4.9 Grounding Systems

4.9.1 Visual and Mechanical Inspection

4.9.1.1 Inspect ground system for compliance with drawings.

4.9.2 Electrical Tests

4.9.2.1 Perform three (3) point fall-of-potential test per IEEE Standard No.

4.9.2.3 Alternate Method to 4.8.2.2:

4.9.3 Test Values

4.10.1 Batteries

4.10.1.1 Visual and Mechanical Inspection

4.10.1.2.1 Measure bank charging voltage and each individual cell voltage.

4.10.1.2.2 Measure electrolyte specific gravity and visually check fill level.

4.10.1.2.3 Perform contact integrity tests across all connections between adjacent terminals.

4.10.1.2.4 Perform an integrity load test.

4.10.1.2.5 Perform a capacity load test at five year intervals.

4.10.1.2.6 Verify proper changing rates from charger during recharge mode.

4.10.1.2.7 Verify individual cell acceptance of charge during recharge mode.

4.11 Emergency Systems

4.11.1 Engine Generator-(Prime Mover is not addressed in this Specification).

4.11.1.1 Visual and Mechanical Inspection

4.11.1.1.1 Inspect for physical damage.

4.11.1.1.2 Inspect for proper anchorage and grounding. 4.11.1.2 Electrical and Mechanical Tests

4.11.1.3 Test Values

4.11.1.3.1 Perform dielectric absorption at test voltage listed in Table 10.2. Polarization index values shall be in accordance with IEEE Standard 43.

4.11.2 Automatic Transfer Switches

4.11.2.1 Visual and Mechanical Inspection 4.11.2.1.1 Inspect for physical damage.

4.11.2.1.2 Check switch to ensure positive interlock between normal and alternate sources. Mechanical and Electrical.

4.11.2.1.3 Check tightness of all control and power connections.

4.11.2.1.4 Perform manual transfer operation with no connected load.

4.11.2.1.5 Ensure manual transfer warnings are attached and visible to operator.

4.11.2.2 Electrical Tests

4.11.2.2.1 Perform insulation resistance tests phase to-ground with switch in both source positions, where possible.

4.11.2.2.2 Perform a contact resistance test or measure millivolt drop across all main contacts.

4.11.2.2.3 Verify settings and operation of control devices in accordance with the owner/user's electrical engineer's specifications.

4.11.2.2.3.1 Voltage and frequency sensing relays.

4.11.2.2.3.2 All time delay relays.

4.11.2.2.3.3 Engine start and shutdown relays.

4.11.2.2.4 Perform automatic transfer tests:

4.11.2.2.4.1 Simulate loss of normal power.

4.11.2.2.4.2 Return to normal power.

4.11.2.2.4.3 Simulate loss of emergency power.

4.11.2.2.4.4 Simulate all forms of single-phase conditions.

4.11.2.2.5 Monitor and verify correct operation and timing.

4.11.2.2.5.1 Normal voltage sensing relays.

4.11.2.2.5.2 Engine start sequence.

4.11.2.2.5.3 Time delay upon transfer.

4.11.2.2.5.4 Alternate voltage sensing relays.

4.11.2.2.5.5 Automatic transfer operation.

4.11.2.2.5.6 Interlocks and limit switch function.

4.11.2.2.5.7 Time delay and retransfer upon normal power restoration.

4.11.2.2.5.8 Engine cool down and shutdown feature. 4.11.2.3Test Values

4.11.2.3.1 Insulation resistance test voltages and minimum values to be in accordance with Table 10.2.

4.11.2.3.2 Determine contact resistance in microfilm.

Investigate any value exceeding 500 microohm’s or any values which deviate from adjacent poles by more than fifty percent (50—)

SYSTEM FUNCTION TESTS

5.1 General

5.1.1 Perform system Function Tests upon completion of equipment tests as defined in Section 4. It is the purpose of System Function Tests to prove the proper interaction of all sensing, processing and action devices.

5.1.2 Implementation

5.1.2.1 The testing firm shall develop test parameters for the purpose of evaluating performance of all integral components and their functioning as a complete unit within design requirements.

5.1.2.2 The testing firm shall test all interlock safety devices for fail safe functions in addition to design function.

5.1.2.3 The testing firm shall propose methods to initiate the sensing devices.

5.1.2.4 The testing firm shall note the operation of alarms and indicating devices.

HERMOGRAPHIC SURVEY

6.3.3 Cause of heat rise.

6.3.4 Phase unbalance, if present. 6.3.5 Areas scanned.

6.4.2 Equipment shall detect emitted radiation and convert detected radiation to visual signal.

6.5.1 Temperature gradients of 1.0 to 3.0 indicate possible deficiency and warrant investigation.

6.5.2 Temperature gradients of 4.0 to 15.0 indicate deficiency; repair as time permits.

6.5.3 Temperature gradients of 16 C and above indicate major deficiency: repair immediately.

TABLE 7.t U.8. standard Bolt Torques for Bus Connections Beat Treated 8tee1-Ca-mium or Zina Plated

MINIMUM

(P.S.I.)

BOLT

Togue (Foot Pounds)

DIAMETER

Silicon Bronze Fasteners* Torque (Foot Pounds)

*Bronze alloy…