24Q0074 Attachment 1.pdf

RFQ 24Q0074

REQ DOC NO. - RCP 23RX19755 ATTACHMENT 1

NAME OF OFFER OR/CONTRACTOR

0001 NUT, HEX 40 EA

NSN: 1H 5310-01-579-7163 X2, Item 7026AB

C. DESCRIPTION/SPECIFICATIONS

C.1 THIS IS LEVEL I MATERIAL

C.2 NUT, HEX, REGULAR, NICKEL COPPER ALUMINUM (K-MONEL),

LOCKWIRE HOLE, 0.875”-09UNC-2B.

C.3 MANUFACTURE NUTS PER 688-1864 REV K WITH APPENDIX 1&5, AND

MIL-DTL-1222J IC 1 INCORPORATED AS APPLICABLE.

(A) DESIGN, MATERIAL AND QUALITY ASSURANCE REQUIREMENTS

FOR THREADED FASTENERS: 688-1864 WITH APPENDIX 1&5

MODIFIED TO INCLUDE APPLICABLE PORTIONS OF STUDS, BOLTS,

SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE

OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR:

MIL-DTL-1222.

(B) TYPE I (1), REGULAR HEX NUT, STYLE A OR B. NICKEL COPPER

ALUMINUM PER CHEMICAL AND MECHANICAL PROPERTIES OF

MATERIAL NO. 5 (QQ-N-286, ANNEALED AND AGE HARDENED) OF

TABLE I OF 688-1864K. THE SLOW STRAIN RATE TENSILE TEST

REQUIRED ON THE STARTING MATERIAL BY QQ-N-286G SHALL BE

PERFORMED BY ONE OF THE LABS LISTED IN C.3(B)(1).

(1) LIST OF AUTHORIZED LABORATORIES FOR SLOW STRAIN

RATE TENSILE TEST:

ITEM # SUPPLIES/SERVICES QTY U/I

AUTHORIZED LABORATORY CONTACT INFO

1.

Huntington Alloys, a Special Metals Company

3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526‐5100 www.specialmetals.com

2. Naval Surface Warfare Center, Carderock Division

Code 614 9500 Macarthur Blvd West Bethesda, MD 20817‐5700 Phone: (301) 227‐5031

3. ATI Specialty Materials (formerly listed as Teledyne Allvac)

2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289‐4511 www.atimetals.com

4.

Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI)

Postfach 251160 47251 Duisburg Germany Phone: 011‐49‐0203‐9993194

5. Westmoreland Mechanical Testing & Research. Inc.

221 Westmoreland Drive P.O. Box 388 Youngstown, PA 15696‐0388 Phone: (724) 537‐3131 www.wmtr.com

(C) SIZE, THREAD SERIES AND CLASS OF FIT PER PARAGRAPH C.2.

ASME B1.3M, SYSTEM 22S IS INVOKED. LOCKWIRE HOLE

DIAMETER AND LOCATION SHALL BE AS SHOWN IN FIGURE 1

PROVIDED AT THE END OF THIS ATTACHMENT.

(D) COATING NOT APPLICABLE

(E) SELF-LOCKING ELEMENT NOT APPLICABLE

(F) BEARING SURFACE TO BE EITHER WASHER FACED OR

CHAMFERED.

(G) APPLICBLE SPECIFICATION REVISIONS TO BE USED ARE:

SPECIFICATION 688-1864 REV K

MIL-DTL-1222J, IC 1

MIL-I-45208A, AM(1)

MIL-STD-129R

MIL-STD-792F

MIL-STD-2132F

QQ-N-286G

SAE J 123 MAR 94

FOR SPECIFICATIONS NOT LISTED ABOVE, REVISIONS SHALL BE

THOSE LISTED IN THE ACQUISITION STREAMLINING AND

STANDARDIZATION INFORMATION SYSTEM (ASSIST) AT THE TIME

OF CONTRACT AWARD. AS OF THE ISSUE DATE OF THIS, ASSIST

INFORMATION IS AVAILABLE AT THE FOLLOWING WEBSITE:

https://quicksearch.dla.mil

C.4 CLEANLINESS REQUIREMENTS: PARTS SHALL BE CLEANED BY ANY

PROCESS OR COMBINATION OF PROCESSES WHICH WILL

ACCOMPLISH THOROUGH CLEANING WITHOUT DAMAGE TO THE

PARTS. SURFACES SHALL BE EXAMINED VISUALLY TO DETERMINE

FREEDOM FROM DIRT, CORROSION, OIL, GREASE OR FOREIGN

RESIDUE.

C.5 THE CONTRACTOR MUST PROVIDE THE PROCURING ACTIVITY WITH

ALL THE SUBMITTALS LISTED BELOW. SUBMITTALS WHICH ARE

REQUIRED BY A SPECIFICATION, BUT WHICH ARE NOT LISTED, NEED

NOT BE SUBMITTED. ONLY THOSE SUBMITTALS LISTED BELOW ARE

REQUIRED.

C.5.1 MATERIAL CERTIFICATIONS:

C.5.1.1 MARKING

C.5.1.2 VISUAL INSPECTION

C.5.1.3 THREADS

C.5.1.4 DIMENSIONS AND TOLERANCES

C.5.1.5 CHEMICAL TEST

C.5.1.6 HARDNESS TEST

C.5.1.7 PROOF LOAD

C.5.1.8 QQ-N-286 STARTING MATERIAL CERTIFICATION OF

QUALITY CONFORMANCE (INCLUDING CHEMICAL TEST

RESULTS, MECHANICAL TEST RESULTS, SLOW STRAIN

RATE TEST RESULTS WITH COPIES OF SCANNING

ELECTRON MICROSCOPE (SEM) PHOTOS, NON-

DESTRUCTIVE AND OTHER TEST RESULTS REQUIRED BY

QQ-N-286G).

C.5.1.9 CERTIFICATE OF COMPLIANCE

C.5.2 PROCEDURE SUBMITTALS:

C.5.2.1 NO PROCEDURE SUBMITTALS REQUIRED FOR THIS ITEM.

C.6 DATA REQUIREMENTS PER EXHIBIT A (DD-1423) & ATTCHMENT #1

TO EXHIBIT A.

C.6.1 MATERIAL CERTIFICATIONS; EXHIBIT A SEQUENCE A001.

C.6.1.1 THE CONTRACTOR SHALL PROVIDE THE LISTED

PROCEDURE(S)/CERTIFICATION REPORT(S) TO THE

PROCURING ACTIVITY. THE CONTRACTOR SHALL

SPECIFY THE FOLLOWING ON PROCEDURE(S)/REPORT(S)

REQUIRING SUBMITTAL, AS APPLICABLE, IN ORDER THAT

THE PROCEDURE/REPORT CAN BE READILY REVIEWED

AGAINST THE APPROPRIATE ACCEPTANCE CRITERIA:

(1) SPECIFICATIONS AND REVISIONS, INCLUDING

AMENDMENTS, NOTICES, ETC.

(2) APPLICABLE PARAGRAPH OF THE SPECIFICATION

(3) THE NAME OF THE SUBMITTAL

(4) THE MATERIAL CONDITIONS (I.E., MATERIAL

GRADE, CLASS, TYPE, SIZE, COMPOSITION, ETC.)

IF A PARTICULAR CONDITION IS NOT SPECIFIED

AND THE SPECIFICATION PROVIDES FOR

ALTERNATIVE CONDITIONS, THEN THE

CONTRACTOR MAY, IN MANUFACTURING THE

ITEM, SELECT A CONDITION WITHIN THE SCOPE

OF THE SPECIFICATION USING TECHNICAL

JUDGMENT AND ANNOTATE THE REPORT

ACCORDINGLY.

C.7 MATERIAL MARKING

C.7.1 EACH PIECE OF MATERIAL SHALL BE PERMANENTLY MARKED

AT LEAST ONCE WITH THE INFORMATION OF (A), (B), (C), AND

(D) BELOW USING THE PERMANENT MARKING METHODS OF

MIL-STD-792 OR THE PERMANENT MARKING METHOD

SPECIFIED IN THE MATERIAL SPECIFICATION.

(A) "AK" AND “KMD”

(B) VENDOR TRACEABILITY NUMBER TRACEABLE TO ALL

MANUFACTURE TEST AND INSPECTION INFORMATION AND TO

A UNIQUE SET OF PHYSICAL, MECHANICAL, AND CHEMICAL

TEST RESULTS WHICH REPRESENT THE MATERIAL USED TO

MAKE THE PIECE.

(C) THE MANUFACTURER'S NAME, TRADEMARK, OR SYMBOL.

(D) INFORMATION REQUIRED BY THE SPECIFICATION IN

ADDITION TO THAT REQUIRED BY (A), (B), AND (C) ABOVE

SHALL BE MARKED EITHER PER THE SPECIFICATION OR AT

LEAST ONCE PER PERMANENT MARKING METHODS OF MIL-

STD-792. MATERIAL DESIGNATOR LISTED IN THE

SPECIFICATION NEED NOT BE MARKED ON THE MATERIAL IF

IT IS DIFFERENT FROM THAT SPECIFIED BY (A) ABOVE.

C.7.2 IF ANY MARKING SPECIFIED ABOVE CANNOT BE APPLIED DUE

TO SPACE LIMITATION, A WAIVER REQUEST SHALL BE

SUBMITTED TO THE CONTRACTING OFFICER.

C.7.3 WHEN FEASIBLE, CONSOLIDATE THE PLACEMENT OF THE

PERMANENT MARKING TO ACCOMMODATE THE MARKING OF

A 9-DIGIT FINAL ACCEPTANCE MARKING AT PORTSMOUTH

NAVAL SHIPYARD. DO NOT COMPROMISE LEGIBILITY OF THE

PERMANENT MARKING TO CONSOLIDATE THE SPACING.

D. PRESERVATION/PACKAGING/PACKING

D.1 PRESERVATION, PACKAGING, AND PACKING SHALL BE IN

ACCORDANCE WITH ASTM D3951-18, STANDARD PRACTICE FOR

COMMERCIAL PACKAGING, EXCEPT THAT EACH EXTERNALLY

THREADED FASTENER SHALL BE FURNISHED WITH A THREAD

PROTECTOR AND EACH ITEM SHALL BE INDIVIDUALLY PACKAGED

IN A COLORED (EXCEPT YELLOW) TRANSPARENT ZIP-LOCK TYPE

PACKAGE WITH A MINIMUM SIZE OF 4” X 7”. MARKING AND

LABELING SHALL BE IN ACCORDANCE WITH MIL-STD-129. BAR

CODE MARKING FOR HAND SCANNING IS REQUIRED.

E. INSPECTION AND ACCEPTANCE

E.1 GOVERNMENT INSPECTION IS REQUIRED DURING MANUFACTURE

AND PRIOR TO SHIPMENT FROM THIS FACILITY. UPON RECEIPT OF

THIS ORDER, PROMPTLY NOTIFY THE REPRESENTATIVE OF THE

GOVERNMENT OFFICE WHO NORMALLY SERVES YOUR FACILITY SO

THAT APPROPRIATE PLANNING FOR GOVERNMENT INSPECTION CAN

BE ACCOMPLISHED. IN THE EVENT A REPRESENTATIVE OF THE

GOVERNMENT OFFICE CANNOT BE LOCATED, THE CONTRACT

SPECIALIST SHOULD BE NOTIFIED PROMPTLY. PROVIDE THE

LOCATION WHERE PROCUREMENT QUALITY ASSURANCE (PQA) OF

THE SUPPLIES WILL BE MADE ALONG WITH THE ORGANIZATION

THAT WILL BE PERFORMING PQA.

E.2 ALL NON-CONFORMANCES TO CONTRACT REQUIREMENTS

AFFECTING PRODUCT AND/OR DOCUMENTATION SHALL REQUIRE

PROCURING ACTIVITY WAIVER APPROVAL TO ACCEPT.

E.3 APPROVED SAMPLING PLANS (E.G. MIL-STD-105, ANSI/ASQC Z1.4)

ARE ALLOWED AS DELINEATED IN THE APPLICABLE

MANUFACTURING SPECIFICATION EXCEPT THAT A LOT IS

ACCEPTABLE BASED ON ZERO DEFECTS. WHEN A REJECT IS FOUND,

THE ENTIRE LOT SHALL BE INSPECTED FOR THAT ATTRIBUTE AND

ANY DEFECTIVE ITEMS SHALL BE REMOVED FROM THE LOT IN

ORDER FOR THE LOT TO BE ACCEPTABLE

FIGURE 1

LOCKWIRE HOLE DIAMETER AND LOCATION