2024.11.08-230232J-GILPIN COUNTY-JUSTICE CENTER GEN-E.pdf

COPYRIGHT RESERVED

SEAL:

SHEET TITLE:

NOTICE: DUTY OF COOPERATION Release of these plans contemplates further coordination among the owner, his contractor(s), the architect and engineers. Design and construction are complex. Although the architect and his consultants have performed their services with due care and diligence, they cannot guarantee perfection. Communication is imperfect, and every contingency cannot be anticipated. Any ambiguity or discrepancy discovered by the use of these plans shall be reported immediately to the architect. Failure to notify the architect compounds misunderstanding and increases construction costs. A failure to cooperate by a notice to the architect shall relieve the architect/engineer from responsibility for all consequences. Changes made from the plans without consent of the architect are unauthorized, and shall relieve the architect/engineer of responsibility for all consequences caused by such changes.

REVISIONS

DATE DESCRIPTION NO.

323 3RD AVENUE, #100

TEL: 1.303.678.1108

LONGMONT, CO 80501

BOWMAN.COM

Bowman

PROJECT NO.:

DRAWN BY:

PM:

230548J

CHECKED BY/CC:

EOR:

ELECTRICAL

LEGEND AND

NOTES

E0.1

WN AP

WNBE

AutoCAD SHX Text

ELECTRICAL LEGEND

AutoCAD SHX Text

SYMBOL

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

UNDERGROUND/FLOOR CIRCUIT

AutoCAD SHX Text

WIREMOLD/PLUGMOLD (SURFACE RACEWAY)

AutoCAD SHX Text

CONDUIT TURNS UP

AutoCAD SHX Text

CONDUIT TURNS DOWN

AutoCAD SHX Text

JUNCTION BOX

AutoCAD SHX Text

PANELBOARD (NEW/EXISTING)

AutoCAD SHX Text

FIXTURE TYPE (SEE SCHEDULE)

AutoCAD SHX Text

SWITCH LETTER / MULTI-GANG NUMERAL

AutoCAD SHX Text

PANEL AND CIRCUIT NUMBER

AutoCAD SHX Text NOTE: NOT ALL SYMBOLS OR ABBREVIATIONS ON THIS LEGEND ARE NECESSARILY USED ON THIS PROJECT.

AutoCAD SHX Text A

AutoCAD SHX Text B-2

AutoCAD SHX Text IIa

AutoCAD SHX Text

FIXTURE TYPE SYMBOL

AutoCAD SHX Text J

AutoCAD SHX Text

SYMBOL

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text RECESSED 2x2 LUMINAIRE

AutoCAD SHX Text SURFACE MOUNT 2x4 LUMINAIRE

AutoCAD SHX Text RECESSED 2x4 LUMINAIRE

AutoCAD SHX Text SURFACE MOUNT 1x4 LUMINAIRE

AutoCAD SHX Text

SURFACE MOUNT ROUND LUMINAIRE

AutoCAD SHX Text

RECESSED ROUND LUMINAIRE

AutoCAD SHX Text

RECESSED ROUND LUMINAIRE WITH EMERGENCY BATTERY BACK-UP

AutoCAD SHX Text

PENDANT LUMINAIRE

AutoCAD SHX Text

SURFACE MOUNT STRIP LUMINAIRE

AutoCAD SHX Text

WALL MOUNTED LUMINAIRE

AutoCAD SHX Text

POLE MOUNTED LUMINAIRE

AutoCAD SHX Text

WALL MOUNTED EMERGENCY BATTERY BACK-UP

AutoCAD SHX Text EXIT SIGN WITH DIRECTIONAL ARROWS HATCH INDICATES ILLUMINATED FACES, ARROWS INDICATE DIRECTIONS

AutoCAD SHX Text

RECEPTACLE - DUPLEX

AutoCAD SHX Text

RECEPTACLE - DUPLEX WITH ISOLATED GROUND

AutoCAD SHX Text

RECEPTACLE - DUPLEX WITH GFCI PROTECTION

AutoCAD SHX Text

RECEPTACLE - DUPLEX SPLIT WIRE

AutoCAD SHX Text

RECEPTACLE - QUADRAPLEX (DOUBLE DUPLEX)

AutoCAD SHX Text

RECEPTACLE - SPECIAL PURPOSE - SINGLE PHASE

AutoCAD SHX Text

RECEPTACLE - SPECIAL PURPOSE - THREE PHASE

AutoCAD SHX Text

RECEPTACLE - RANGE

AutoCAD SHX Text

RECEPTACLE - DUPLEX - FLOOR MOUNTED

AutoCAD SHX Text

RECEPTACLE - QUADRAPLEX - FLOOR MOUNTED

AutoCAD SHX Text SWITCH (TOGGLE UNLESS NOTED): TO - THERMAL OVERLOAD 3 - 3-WAY 4 - 4-WAY T - TIMER D - DIMMER D - DIMMER OS - OCCUPANCY SENSOR VS - VACANCY SENSOR

AutoCAD SHX Text a

AutoCAD SHX Text F

AutoCAD SHX Text

MOTOR DEVICE

AutoCAD SHX Text AC - ABOVE COUNTER AFF - ABOVE FINISHED FLOOR BAS - BUILDING AUTOMATION SYSTEM BLDG - BUILDING BMS - BUILDING MANAGEMENT SYSTEM CR - CARD READER D - DEMO EXISTING E - EXISTING EC - ELECTRICAL CONTRACTOR EF - EXHAUST FAN EM - EMERGENCY FIXTURE EOR - ENGINEER OF RECORD EPO - EMERGENCY POWER OFF EWC - ELECTRIC WATER COOLER FACP - FIRE ALARM CONTROL PANEL GFI - GROUND FAULT INTERRUPTER GFCI - GROUND FAULT CIRCUIT INTERRUPTER J - JUNCTION BOX OS - OCCUPANCY SENSOR TC - TIME CLOCK TV - TELEVISION VS - VACANCY SENSOR XFMR - TRANSFORMER WP - WEATHERPROOF

AutoCAD SHX Text

FUSED SAFETY DISCONNECT SWITCH

AutoCAD SHX Text

OS

AutoCAD SHX Text

OCCUPANCY SENSOR - CEILING/WALL

AutoCAD SHX Text

CEILING MOUNTED EMERGENCY BATTERY BACK-UP

AutoCAD SHX Text

VS

AutoCAD SHX Text

VACANCY SENSOR - CEILING/WALL

AutoCAD SHX Text

DS

AutoCAD SHX Text

DAYLIGHT SENSOR - CEILING/WALL

AutoCAD SHX Text

WALL MOUNT STRIP LUMINAIRE

AutoCAD SHX Text

RECEPTACLE - SINGLE - CEILING MOUNTED

AutoCAD SHX Text

RECEPTACLE - DUPLEX - CEILING MOUNTED

AutoCAD SHX Text

RECEPTACLE - QUADRAPLEX - CEILING MOUNTED

AutoCAD SHX Text

NEW WORK UNDER THIS CONTRACT

AutoCAD SHX Text

WORK DEMOLISHED UNDER THIS CONTRACT

AutoCAD SHX Text

WORK EXISTING TO REMAIN UNDER THIS CONTRACT

AutoCAD SHX Text

ELECTRICAL DRAWING INDEX

AutoCAD SHX Text

DRAWING TITLE

AutoCAD SHX Text

ELECTRICAL LEGEND AND NOTES

AutoCAD SHX Text E0.1

AutoCAD SHX Text

DRAWING

AutoCAD SHX Text

NUMBER

AutoCAD SHX Text

11/08/2024 - 100%%% CD SET

AutoCAD SHX Text

ELECTRICAL RISER DIAGRAM

AutoCAD SHX Text E0.2

AutoCAD SHX Text

ELECTRICAL PANEL SCHEDULES

AutoCAD SHX Text E0.3

AutoCAD SHX Text

ISSUE DATE - DESCRIPTION

AutoCAD SHX Text GENERAL NOTES: A. REVIEW THE CONTRACT CONDITIONS AND GENERAL REQUIREMENTS FOR REVIEW THE CONTRACT CONDITIONS AND GENERAL REQUIREMENTS FOR INFORMATION THAT APPLIES. B. THE WORD "PROVIDE" IS USED TO MEAN "FURNISH AND INSTALL." THE WORD "PROVIDE" IS USED TO MEAN "FURNISH AND INSTALL." C. PROVIDE ALL ITEMS FOR A COMPLETE AND SUCCESSFUL OPERATION OF ALL PROVIDE ALL ITEMS FOR A COMPLETE AND SUCCESSFUL OPERATION OF ALL SYSTEMS SHOWN ON THESE DRAWINGS. D. THE DRAWINGS ARE DIAGRAMMATIC AND INDICATE GENERAL ARRANGEMENT OF THE DRAWINGS ARE DIAGRAMMATIC AND INDICATE GENERAL ARRANGEMENT OF THE WORK. LOCATIONS ARE APPROXIMATE UNLESS DIMENSIONED. MINOR MODIFICATIONS IN LOCATION TO MEET SITE REQUIREMENTS ARE ACCEPTABLE. REFER TO LATEST ARCHITECTURAL DRAWINGS FOR EXACT WALL LOCATIONS AND DIMENSIONS. E. THE ARCHITECTURAL AND ENGINEERING DRAWINGS ARE COMPLEMENTARY. THE ARCHITECTURAL AND ENGINEERING DRAWINGS ARE COMPLEMENTARY. GENERAL CONTRACTORS, SUBCONTRACTORS, AND VENDORS SHALL ACKNOWLEDGE ALL THE ARCHITECTURAL AS WELL AS ALL THE ENGINEERING DRAWINGS AND INCLUDE ALL WORK NECESSARY TO ACHIEVE A COMPLETE WORKING INSTALLATION FOR ALL DEVICES OR EQUIPMENT WHICH MAY BE SHOWN ON ONE DRAWING BUT NOT SHOWN ON ANOTHER. WHERE ELEMENTS ARE INDICATED OR DESCRIBED IN ANY DRAWING, IT IS THE INTENT THAT ALL RELATED CONSTRUCTION ASSOCIATED WITH SUCH ELEMENTS IS TO BE INCLUDED IN ORDER TO OBTAIN A COMPLETE INSTALLATION. FOR INSTANCE, IF A PIECE OF EQUIPMENT IS IDENTIFIED IN THE ARCHITECTURAL AND/OR MECHANICAL DRAWINGS, BUT THE ELECTRICAL CIRCUIT FOR SUCH EQUIPMENT IS NOT IDENTIFIED IN THE ELECTRICAL DRAWINGS, THE CONTRACTOR IS TO PROVIDE SUCH CIRCUIT IN ORDER TO HAVE FULLY OPERATIONAL EQUIPMENT. THEY ARE TO BE INCLUDED IN ORDER TO RESULT IN A FULLY OPERATIONAL SYSTEM. NO SUBCONTRACTOR SHALL BE ALLOWED TO EXCLUDE PORTIONS OF THE COMPLIMENTARY DRAWING SET. F. LAY OUT ALL WORK IN ADVANCE. DO NOT DEFACE THE WORK OF OTHER LAY OUT ALL WORK IN ADVANCE. DO NOT DEFACE THE WORK OF OTHER TRADES OR THE EXISTING BUILDING. G. LOCATION OF PIPES, DUCTS, SWITCHES, PANELS, EQUIPMENT, AND FIXTURES LOCATION OF PIPES, DUCTS, SWITCHES, PANELS, EQUIPMENT, AND FIXTURES SHALL BE COORDINATED IN ADVANCE TO ACCOMMODATE THE WORK OR ANTICIPATED INTERFERENCES. DETERMINE THE EXACT ROUTE AND LOCATION OF EACH PIPE AND DUCT PRIOR TO FABRICATION. G.A. RIGHT-OF-WAY: LINES WHICH PITCH SHALL HAVE THE RIGHT-OF-WAY OVER RIGHT-OF-WAY: LINES WHICH PITCH SHALL HAVE THE RIGHT-OF-WAY OVER THOSE WHICH DO NOT PITCH. LINES WHOSE ELEVATIONS CANNOT BE CHANGED SHALL HAVE THE RIGHT-OF-WAY OVER LINES WHOSE ELEVATIONS CAN BE CHANGED. G.B. OFFSETS, TRANSITIONS, AND CHANGES IN DIRECTION: OFFSETS, OFFSETS, TRANSITIONS, AND CHANGES IN DIRECTION: OFFSETS, TRANSITIONS, AND CHANGES IN DIRECTION OF PIPES AND DUCTS SHALL BE MADE AS REQUIRED TO MAINTAIN PROPER HEADROOM AND PITCH OF SLOPING LINES WHETHER OR NOT INDICATED ON THE DRAWINGS. H. ALL PENETRATIONS OF FIRE RATED WALLS, FLOORS, AND CEILINGS SHALL HAVE ALL PENETRATIONS OF FIRE RATED WALLS, FLOORS, AND CEILINGS SHALL HAVE THE SPACE AROUND PENETRATIONS SEALED WITH A FIRE BARRIER SEALANT MEETING THE REQUIREMENTS OF U.L. STANDARD 1479 AND ASTM-E 814. INSTALL SEALANT IN FULL COMPLIANCE WITH MANUFACTURER'S STANDARD INSTALLATION INSTRUCTIONS. I. ALL MATERIALS LOCATED ABOVE CEILING SHALL BE SUITABLE FOR USE WITHIN ALL MATERIALS LOCATED ABOVE CEILING SHALL BE SUITABLE FOR USE WITHIN A RETURN AIR PLENUM AS REQUIRED BY THE LATEST EDITION OF THE INTERNATIONAL MECHANICAL CODE. J. WHEN USING A TORCH OR OTHER FLAME-PRODUCING DEVICE ON THIS PROJECT, WHEN USING A TORCH OR OTHER FLAME-PRODUCING DEVICE ON THIS PROJECT, CONTRACTOR SHALL PROVIDE ONE APPROVED FIRE EXTINGUISHER OR WATER HOSE EQUIPPED WITH A SUITABLE NOZZLE, SUFFICIENT IN LENGTH TO REACH ALL PORTIONS OF THE BUILDING AND CONNECTED TO A WATER SUPPLY ON THE PREMISES WHERE SAID BURNING OPERATION IS PERFORMED. COMBUSTIBLE MATERIAL IN THE CLOSE PROXIMITY OF OPEN FLAME SHALL BE PROTECTED AGAINST IGNITION BY SHIELDING, WETTING, OR OTHER MEANS. IN ALL CASES, A FIRE WATCH SHALL BE MAINTAINED IN THE VICINITY OF THE OPERATION BY THE CONTRACTOR FOR ONE-HALF HOUR AFTER THE TORCH OR FLAME-PRODUCING DEVICE HAS BEEN USED. K. THE CONTRACTOR SHALL VISIT THE SITE PRIOR TO BIDDING THE PROJECT AND THE CONTRACTOR SHALL VISIT THE SITE PRIOR TO BIDDING THE PROJECT AND TAKE INTO CONSIDERATION CONDITIONS THAT MAY AFFECT THE WORK. NO ADDITIONAL COMPENSATION WILL BE APPROVED FOR FAILURE TO VISIT THE SITE PRIOR TO PRICING THE WORK. L. MAINTAIN A CONTRACT SET OF THESE DRAWINGS AT THE SITE, WITH ALL MAINTAIN A CONTRACT SET OF THESE DRAWINGS AT THE SITE, WITH ALL CHANGES OR DEVIATIONS FROM THE ORIGINAL DRAWINGS NEATLY MARKED ON THEM IN RED COLOR. THIS SHALL BE A SEPARATE SET OF DRAWINGS NOT USED FOR CONSTRUCTION PURPOSES, WHICH SHALL BE KEPT UP TO DATE AS THE JOB PROGRESSES AND SHALL BE MADE AVAILABLE FOR INSPECTION BY THE ENGINEER AT ALL TIMES. UPON COMPLETION OF THE CONTRACT, THIS SET OF "AS-BUILTS" SHALL BE DELIVERED TO THE ENGINEER WITHIN 15 DAYS OF COMPLETION OF THE PROJECT OR SOONER AS REQUIRED. M. MATERIAL SHALL BE AS SPECIFIED. SUBSTITUTIONS WILL BE CONSIDERED IF MATERIAL SHALL BE AS SPECIFIED. SUBSTITUTIONS WILL BE CONSIDERED IF SUBMITTED FOR PRIOR APPROVAL AT LEAST ONE (1) WEEK PRIOR TO THE CONTRACT BID DATE. SUBSTITUTIONS SHOULD BE SUBMITTED SEPARATELY FOR EACH PRODUCT WITH SUPPORTING DATA, DRAWINGS AND SAMPLES AS APPROPRIATE, INCLUDING: 1.) COMPARISON OF THE QUALITIES OF THE PROPOSED SUBSTITUTION WITH THAT SPECIFIED. 2.) CHANGES REQUIRED IN OTHER ELEMENTS OF THE WORK BECAUSE OF THE SUBSTITUTION. 3.) COST DATA COMPARING THE PROPOSED SUBSTITUTION WITH THE PRODUCT SPECIFIED. THE ENGINEER WILL DETERMINE THE ACCEPTABILITY OF THE PROPOSED SUBSTITUTION. N. WHEN ALTERNATE OR SUBSTITUTED EQUIPMENT IS USED, CONTRACTOR IS WHEN ALTERNATE OR SUBSTITUTED EQUIPMENT IS USED, CONTRACTOR IS RESPONSIBLE FOR COORDINATING SPACE REQUIREMENTS, CONFIGURATIONS, CHANGES IN SUPPORTS OR STRUCTURAL MEMBERS, ELECTRICAL REQUIREMENTS, AND COORDINATION OF OTHER TRADES THAT MAY BE AFFECTED BY THEIR USE. CONTRACTOR IS RESPONSIBLE FOR VERIFYING THE SAME WHEN USING LISTED APPROVED MANUFACTURERS OTHER THAN THE BASIS OF DESIGN. O. SUBMIT ELECTRONIC PDF OF MANUFACTURER'S SHOP DRAWINGS FOR EQUIPMENT SUBMIT ELECTRONIC PDF OF MANUFACTURER'S SHOP DRAWINGS FOR EQUIPMENT AND DEVICES. PRIOR TO SUBMITTING THE SHOP DRAWINGS FOR REVIEW, THE CONTRACTOR SHALL REVIEW AND CERTIFY SAME AS TO COMPLIANCE WITH THE PLANS AND SPECIFICATIONS AND FOR DIMENSIONAL SUITABILITY FOR THE APPLICATIONS. P. THE CONTRACTOR SHALL PROVIDE ALL EQUIPMENT AND PERSONNEL REQUIRED THE CONTRACTOR SHALL PROVIDE ALL EQUIPMENT AND PERSONNEL REQUIRED FOR TESTING OF INSTALLED EQUIPMENT. Q. THE CONTRACTOR SHALL DEMONSTRATE THE PROPER OPERATION AND THE CONTRACTOR SHALL DEMONSTRATE THE PROPER OPERATION AND CALIBRATION OF ALL SYSTEMS TO THE OWNER, AT A TIME AS AGREED TO BY THE OWNER AND DIRECTED BY THE OWNER. R. THE CONTRACTOR SHALL PROVIDE THE OWNER WITH OPERATION AND THE CONTRACTOR SHALL PROVIDE THE OWNER WITH OPERATION AND MAINTENANCE MANUALS FOR ALL SYSTEMS WITHIN 15 DAYS OF THE COMPLETION OF THE PROJECT OR SOONER AS REQUIRED. S. THE CONTRACTOR SHALL INCLUDE THE COST FOR COMMISSIONING BY PCD THE CONTRACTOR SHALL INCLUDE THE COST FOR COMMISSIONING BY PCD ENGINEERING TO VERIFY THE PERFORMANCE OF THE SYSTEM CONTROLS SHOWN ON THIS DRAWING. THIS INCLUDES PREPARING A COMMISSIONING PLAN, VERIFYING THE OPERATION OF ALL LIGHTING CONTROL SYSTEMS PER CODE REQUIREMENTS, AND PROVIDING A FINAL COMMISSIONING REPORT. FINAL COMMISSIONING REPORT IS DUE UPON COMPLETION OF THE PROJECT. CODES, REGULATIONS, AND STANDARDS: 1. ALL WORK SHALL BE IN STRICT ACCORD WITH LOCAL GOVERNING LAWS, ALL WORK SHALL BE IN STRICT ACCORD WITH LOCAL GOVERNING LAWS, ORDINANCES, AND REGULATIONS; ALL WORK MUST BE IN FULL ACCORDANCE WITH ALL CODES, ORDINANCES, AND CODE RULINGS. CONTRACTOR SHALL PROVIDE, WITHOUT EXTRA CHARGE, THE LABOR AND MATERIALS REQUIRED FOR FULL CODE COMPLIANCE. 2. ALL MATERIALS SHALL BE NEW AND SHALL COMPLY WITH THE SPECIFICATIONS ALL MATERIALS SHALL BE NEW AND SHALL COMPLY WITH THE SPECIFICATIONS ON DRAWINGS. 3. CONTRACTOR SHALL OBTAIN AND PAY FOR ALL LOCAL FEES, PERMITS, AND CONTRACTOR SHALL OBTAIN AND PAY FOR ALL LOCAL FEES, PERMITS, AND INSPECTION AUTHORITY SERVICES REQUIRED BY THE WORK OF THE PROJECT. THE CONTRACTOR SHALL ARRANGE FOR ALL INSPECTIONS WHEN THEY BECOME DUE AND SHALL NOT COVER ANY WORK UNTIL APPROVED BY THE INSPECTION AUTHORITY. 4. EQUIPMENT AND MATERIALS SHALL BE UL-LISTED FOR THE USE INTENDED. EQUIPMENT AND MATERIALS SHALL BE UL-LISTED FOR THE USE INTENDED. GUARANTEE: A. THE CONTRACTOR SHALL GUARANTEE ALL WORKMANSHIP, MATERIALS, AND THE CONTRACTOR SHALL GUARANTEE ALL WORKMANSHIP, MATERIALS, AND EQUIPMENT PROVIDED FOR THE PROJECT AGAINST DEFECTS AND/OR FAULTY WORKMANSHIP FOR A PERIOD OF ONE YEAR FROM THE DATE OF FINAL ACCEPTANCE BY THE OWNER. B. THE CONTRACTOR SHALL REPAIR AND/OR REPLACE DEFECTIVE OR FAULTY THE CONTRACTOR SHALL REPAIR AND/OR REPLACE DEFECTIVE OR FAULTY WORKMANSHIP, MATERIALS, OR EQUIPMENT, AND SHALL BE RESPONSIBLE FOR THE REPAIR AND/OR REPLACEMENT OF OTHER PROPERTY OR WORK DAMAGED AS A RESULT, WITHOUT CHARGE TO THE OWNER AND AS QUICKLY AS POSSIBLE, DURING THE GUARANTEE PERIOD.

AutoCAD SHX Text

SPECIFICATION GENERAL NOTES

AutoCAD SHX Text

PROJECT DESCRIPTION

AutoCAD SHX Text THIS PROJECT INVOLVES REPLACING THE EXISTING DIESEL GENERATOR WITH A NEW LARGER DIESEL GENERATOR TO SERVE THE ENTIRE FACILITY. THE PREVIOUS GENERATOR ONLY PROVIDED BACKUP POWER SOURCE FOR A PORTION OF THE BUILDING AND ABOUT 30 YEARS OLD DUE FOR AN REPLACEMENT UPGRADE. NEW WORK INCLUDES MODIFICATION OF THE EXISTING ELECTRICAL SERVICE TO ACCOMMODATE FOR THE NEW GENERATOR AND ITS SYSTEM.

AutoCAD SHX Text

NON-FUSED SAFETY DISCONNECT SWITCH

AutoCAD SHX Text J

AutoCAD SHX Text

TRACK LIGHTING

AutoCAD SHX Text

KEY: FULL SHEET ISSUE. PARTIAL SHEET ISSUE (SKETCH).

AutoCAD SHX Text THE DRAWINGS AND SPECIFICATIONS FOR THIS PROJECT ARE COPYRIGHT, BOWMAN CONSULTING GROUP, WHICH SHALL RETAIN ALL RIGHTS OF OWNERSHIP AND COPYRIGHT FOR THE INFORMATION AND DATA DESCRIBED HEREIN, WHETHER IN HARDCOPY OR ELECTRONIC FORMAT. THESE DOCUMENTS MAY NOT BE BID, REPRODUCED, OR COPIED FOR USE ON ANY OTHER PROJECT WITHOUT WRITTEN PERMISSION FROM BOWMAN CONSULTING GROUP.

AutoCAD SHX Text P

AutoCAD SHX Text

EXIT SIGN WITH DUAL FROG EYE

AutoCAD SHX Text

DATA OUTLET

AutoCAD SHX Text

COMBINATION DATA/TELE. OUTLET

AutoCAD SHX Text

TELEPHONE OUTLET

AutoCAD SHX Text

TELEVISION OUTLET

AutoCAD SHX Text

1. THE ELECTRICAL CONTRACTOR SHALL VERIFY THAT ALL ELECTRICAL ITEMS TO REMAIN OR BE THE ELECTRICAL CONTRACTOR SHALL VERIFY THAT ALL ELECTRICAL ITEMS TO REMAIN OR BE RELOCATED AND REUSED ARE IN WORKING ORDER PRIOR TO ANY DEMOLITION WORK. IF THE EXISTING MATERIAL IS FOUND TO BE INOPERABLE, CONTRACTOR SHALL INFORM THE OWNER. ONCE ANY DEMOLITION WORK HAS BEGUN, ANY INOPERABLE OR DAMAGED MATERIAL SHALL BE REPAIRED OR REPLACED AT THE CONTRACTOR'S EXPENSE. 2. VERIFICATION OF EXISTING CONDITIONS. "INASMUCH AS THE REMODELING AND/OR VERIFICATION OF EXISTING CONDITIONS. "INASMUCH AS THE REMODELING AND/OR REHABILITATION OF THE EXISTING BUILDING REQUIRES THAT CERTAIN ASSUMPTIONS BE MADE REGARDING EXISTING CONDITIONS, AND BECAUSE SOME OF THESE ASSUMPTIONS MAY NOT BE VERIFIABLE WITHOUT DESTROYING OTHERWISE ADEQUATE OR SERVICEABLE PORTIONS OF THE BUILDING, THE GENERAL CONTRACTOR AGREES THAT, EXCEPT FOR NEGLIGENCE ON THE PART OF THE DESIGN PROFESSIONAL THE CONTRACTOR WILL HOLD HARMLESS, INDEMNIFY AND DEFEND THE DESIGN PROFESSIONAL FROM AND AGAINST ANY AND ALL CLAIMS ARISING OUT OF THE PROFESSIONAL SERVICES PROVIDED." 3. ANY ELECTRICAL ITEMS SHOWN OR NOT SHOWN ON THE PLANS, OR WHERE CIRCUITS IN ANY ELECTRICAL ITEMS SHOWN OR NOT SHOWN ON THE PLANS, OR WHERE CIRCUITS IN EXISTING WALLS ARE REMOVED BY DEMOLITION, SHALL UPON COMPLETION OF REMODEL WORK BE LEFT IN WORKING CONDITION. 4. ALL PHASES OF THE ELECTRICAL WORK SHALL BE COORDINATED WITH THE ARCHITECT. WORK ALL PHASES OF THE ELECTRICAL WORK SHALL BE COORDINATED WITH THE ARCHITECT. WORK SHALL BE DONE IN A FASHION TO CAUSE AS LITTLE INCONVENIENCE AS POSSIBLE TO THE OWNER. 5. ELECTRICAL DEVICES NOTED TO BE REMOVED SHALL BE REMOVED BACK TO A POINT WHERE ELECTRICAL DEVICES NOTED TO BE REMOVED SHALL BE REMOVED BACK TO A POINT WHERE EXISTING CONDUIT CAN BE ABANDONED IN CONCEALED SPACES. REMOVE ALL WIRING FROM ABANDONED CONDUIT. ALL BOXES TO BE REMOVED SHALL BE TAKEN OUT OF WALLS AND HAVE HOLES REFINISHED TO MATCH WALL FINISH. 6. ELECTRICAL CONTRACTOR SHALL NOT DEFACE ANY AREAS OF THE BUILDING WHERE ELECTRICAL CONTRACTOR SHALL NOT DEFACE ANY AREAS OF THE BUILDING WHERE REMODELING IS NOT BEING DONE. 7. RACEWAYS: ALL CONDUIT SHALL BE CONCEALED WHEREVER POSSIBLE. CONDUIT SHALL NOT RACEWAYS: ALL CONDUIT SHALL BE CONCEALED WHEREVER POSSIBLE. CONDUIT SHALL NOT BE EXPOSED IN FINISHED AREAS (EXCLUDES MECHANICAL ROOMS, STORAGE CLOSETS, AND SIMILAR AREAS). EXPOSED RACEWAYS SHALL BE SURFACE RACEWAYS PER SPECIFICATIONS. RACEWAYS MAY BE THE FOLLOWING (SUBJECT TO NEC REQUIREMENTS); ELECTRICAL METALLIC TUBING, GALVANIZED POLYVINYL CHLORIDE CONDUIT, SCHEDULE 40. 8. CABLE ASSEMBLIES MAY BE THE FOLLOWING (SUBJECT TO NEC REQUIREMENTS): METALCLAD CABLE ASSEMBLIES MAY BE THE FOLLOWING (SUBJECT TO NEC REQUIREMENTS): METALCLAD CABLE. 9. PROVIDE COMPLETE SYSTEMS OF CONDUCTORS AND RACEWAYS USING CONDUIT AND/OR PROVIDE COMPLETE SYSTEMS OF CONDUCTORS AND RACEWAYS USING CONDUIT AND/OR CABLE ASSEMBLIES APPROPRIATE TO THE FUNCTION & LOCATION AND APPROVED PER NEC REQUIREMENTS. CONDUCTORS MUST BE DERATED PER CODE. 10. ROUTING OF EXISTING CONCEALED CONDUIT NOT KNOWN. LOCATION DETERMINED BY ROUTING OF EXISTING CONCEALED CONDUIT NOT KNOWN. LOCATION DETERMINED BY ELECTRICAL CONTRACTOR. ELECTRICAL CONTRACTOR SHALL RECIRCUIT AS NOTED UTILIZING ANY EXISTING CONDUIT. HE SHALL REMOVE EXISTING WIRE AND REPULL NEW. ALL NEW CONDUIT ADDED SHALL BE CONCEALED WHEREVER POSSIBLE. 11. SURFACE RACEWAY: WHEREVER CONCEALED CONDUIT IN FINISHED AREAS IS NOT POSSIBLE, SURFACE RACEWAY: WHEREVER CONCEALED CONDUIT IN FINISHED AREAS IS NOT POSSIBLE, ELECTRICAL CONTRACTOR SHALL INSTALL SURFACE MOUNTED RACEWAYS EQUAL TO WIREMOLD. RUN SURFACE RACEWAYS IN CORNER OF WALL AND CEILING. ALL RACEWAYS THAT ARE EXPOSED SHALL BE APPROVED BY ARCHITECT PRIOR TO ROUGH-IN. 12. TERMINATING AND SPLICING: MAKE ALL JOINTS AND SPLICES IN BRANCH CIRCUIT WIRING WITH TERMINATING AND SPLICING: MAKE ALL JOINTS AND SPLICES IN BRANCH CIRCUIT WIRING WITH APPROVED SOLDERLESS TOOL APPLIED OR TWIST-ON CONNECTORS, IN THE VARIOUS BOXES, GUTTERS, AND SIMILAR LOCATIONS, BUT NOT IN RACEWAYS. LEAVE SUFFICIENT SLACK TO PERMIT TWO (2) OR MORE SPLICES OR JOINTS TO BE REMADE IN CASE OF FAULT. 13. ELECTRICAL CONTRACTOR SHALL RECEIVE, FROM SYSTEM SUPPLIERS, ALL WIRING DIAGRAMS ELECTRICAL CONTRACTOR SHALL RECEIVE, FROM SYSTEM SUPPLIERS, ALL WIRING DIAGRAMS FOR ALL EQUIPMENT, PRIOR TO ANY ROUGH-IN, TO ASSURE PROPER ELECTRICAL CHARACTERISTICS ARE PROVIDED. ELECTRICAL CONTRACTOR SHALL PROVIDE ARCHITECT WRITTEN NOTIFICATION PRIOR TO ROUGH-IN, THAT ALL WIRING DIAGRAMS HAVE BEEN RECEIVED AND REVIEWED FOR CORRECTNESS. ANY INCORRECT WIRING OR DEVICES INSTALLED BY ELECTRICAL CONTRACTOR WITHOUT WIRING DIAGRAMS SHALL BE CORRECTED AT ELECTRICAL CONTRACTOR'S EXPENSE. 14. ELECTRICAL CONTRACTOR SHALL RECEIVE, FROM MECHANICAL CONTRACTOR, ALL WIRING ELECTRICAL CONTRACTOR SHALL RECEIVE, FROM MECHANICAL CONTRACTOR, ALL WIRING DIAGRAMS AND SHOP DRAWINGS FOR ALL MECHANICAL EQUIPMENT, PRIOR TO ANY ROUGH-IN, TO ASSURE PROPER ELECTRICAL CHARACTERISTICS, VOLTAGE, PHASE, HORSEPOWER, AMPERE, KILOWATTS AND ETC. ARE PROVIDED. ELECTRICAL CONTRACTOR SHALL PROVIDE ARCHITECT WRITTEN NOTIFICATION PRIOR TO ANY ROUGH-IN, THAT ALL WIRING DIAGRAMS AND SHOP DRAWINGS HAVE BEEN RECEIVED AND REVIEWED FOR CORRECTNESS. ANY INCORRECT WIRING OR DEVICES INSTALLED BY ELECTRICAL CONTRACTOR WITHOUT WIRING DIAGRAMS SHALL BE CORRECTED AT ELECTRICAL CONTRACTOR'S EXPENSE. 15. ALL EXISTING AND NEW SMOKE DETECTORS IN OR NEAR AREAS BEING REMODELED SHALL BE ALL EXISTING AND NEW SMOKE DETECTORS IN OR NEAR AREAS BEING REMODELED SHALL BE BAGGED OR REMOVED. IF REMOVED, STORE IN A SEALED BAG UNTIL ALL REMODELING WORK IS COMPLETE. IF SMOKE DETECTORS ARE NOT BAGGED OR REMOVED THEY SHALL BE REPLACED WITH NEW DETECTORS AT CONTRACTOR'S EXPENSE WHEN THE PROJECT IS COMPLETED. 16. PRIOR TO ROUGH-IN, THE ELECTRICAL CONTRACTOR SHALL VERIFY AND COORDINATE ALL PRIOR TO ROUGH-IN, THE ELECTRICAL CONTRACTOR SHALL VERIFY AND COORDINATE ALL ELECTRICAL DEVICE LOCATIONS WITH THE ARCHITECT OR OWNER. 17. ALL NEW ELECTRICAL ITEMS SHOWN ON EXISTING WALLS AND CEILINGS SHALL BE FLUSH ALL NEW ELECTRICAL ITEMS SHOWN ON EXISTING WALLS AND CEILINGS SHALL BE FLUSH MOUNTED UNLESS NOTED OTHERWISE. CUT AND PATCH EXISTING WALLS AND CEILINGS TO CONCEAL ALL MOUNTING BOXES AND CONDUITS. 18. RELOCATIONS: OWNER RESERVES THE RIGHT TO RELOCATE ANY ELECTRICAL DEVICE, UP TO A RELOCATIONS: OWNER RESERVES THE RIGHT TO RELOCATE ANY ELECTRICAL DEVICE, UP TO A DISTANCE OF 12'-0", BEFORE INSTALLATION WITHOUT EXTRA CHARGE FROM ELECTRICAL CONTRACTOR. 19. CALL UTILITY COMPANIES (POWER, GAS, WATER, SEWER, TELEPHONE, CABLE TV, ETC.) IN CALL UTILITY COMPANIES (POWER, GAS, WATER, SEWER, TELEPHONE, CABLE TV, ETC.) IN ADVANCE BEFORE TRENCHING FOR THE MARKING OF THEIR UNDERGROUND UTILITIES. ALSO CONTRACTOR SHALL LOCATE ALL ON-SITE UTILITIES SUCH AS SECONDARY SERVICE FEEDERS, UNDERGROUND ELECTRICAL BRANCH CIRCUITS, SPRINKLER LINES, ETC. PRIOR TO TRENCHING. ANY CUT OR DAMAGED UNDERGROUND UTILITIES SHALL BE REPAIRED OR REPLACED AT CONTRACTOR'S EXPENSE. 20. EMT CONDUIT FITTINGS: IN DRY LOCATIONS ALL EMT COUPLERS AND CONNECTORS SHALL BE EMT CONDUIT FITTINGS: IN DRY LOCATIONS ALL EMT COUPLERS AND CONNECTORS SHALL BE STEEL SET SCREW TYPE. DIE CAST FITTINGS SHALL NOT BE USED ON THIS PROJECT. IN DAMP/WET LOCATIONS, USE STEEL COMPRESSION GLAND TYPE COUPLERS AND CONNECTORS. 21. ACCESS PANELS REQUIRED BY THE ELECTRICAL CONTRACTOR SHALL BE PROVIDED BY THE ACCESS PANELS REQUIRED BY THE ELECTRICAL CONTRACTOR SHALL BE PROVIDED BY THE ELECTRICAL BID CONTRACTOR, THEN TURNED OVER TO THE APPROPRIATE TRADE FOR INSTALLATION. 22. ELECTRICAL CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH THE GENERAL CONTRACTOR ELECTRICAL CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH THE GENERAL CONTRACTOR TO OBTAIN ACTUAL ROOM NAMES AND NUMBERS, DESIGNATED BY THE OWNER/ARCHITECT AT THE COMPLETION OF THE PROJECT. ACTUAL ROOM NAMES AND NUMBERS SHALL BE USED ON ALL PANEL SCHEDULES, COMPUTER PROGRAMMING, GRAPHIC PLAQUES, SOUND SYSTEMS, TELEPHONE SYSTEMS, INTERCOMS, FIRE ALARMS, SECURITY SYSTEMS, CATV SYSTEMS AND SIMILAR. 23. CONTRACTOR SHALL NOT FASTEN, ATTACH OR HANG ANY MATERIAL FROM THE ROOF DECK. CONTRACTOR SHALL NOT FASTEN, ATTACH OR HANG ANY MATERIAL FROM THE ROOF DECK. ALL CONDUITS, JUNCTION BOXES, FIXTURES, DEVICES AND EQUIPMENT SHALL BE HUNG FROM THE STRUCTURAL STEEL FRAME AND SHALL BE PLACED WITH A MINIMUM OF 1" CLEARANCE BELOW THE ROOF DECK. WIRING AND CONDUITS SHALL NOT BE PLACED WITHIN THE RIBS OF THE ROOF DECK. CONTRACTOR SHALL NOT LOOSEN, REMOVE OR CUT ANY ROOFING SYSTEM FASTENERS PROTRUDING THROUGH THE ROOF DECK. 24. SUPPORT CONDUIT AND EQUIPMENT FROM THE STRUCTURE TO PREVENT SAGGING, SUPPORT CONDUIT AND EQUIPMENT FROM THE STRUCTURE TO PREVENT SAGGING, POCKETING, AND VIBRATION. 25. PROVIDE GALVANIZED STEEL JUNCTION AND OUTLET BOXES, EXCEPT AS INDICATED PROVIDE GALVANIZED STEEL JUNCTION AND OUTLET BOXES, EXCEPT AS INDICATED OTHERWISE. FOR WET LOCATIONS, PROVIDE A WEATHER-PROOF TYPE CAST BOX WITH GASKET AND CAST COVERPLATE. THROUGH THE WALL BOXES ARE NOT PERMITTED. 26. POWER CONDUCTORS SHALL BE COPPER, (STRANDED FOR NO. 8 AWG AND LARGER), WITH POWER CONDUCTORS SHALL BE COPPER, (STRANDED FOR NO. 8 AWG AND LARGER), WITH THE FOLLOWING INSULATION STANDARDS: THHN, THWN, XHHW (90C). THE CONDUCTORS SHALL BE APPLIED USING THE 75C RATING. ALUMINUM CONDUCTORS MAY BE SUBSTITUTED USING THE THE SAME CAPACITY OF THE COPPER CONDUCTORS SPECIFIED. 27. PROVIDE SPECIFICATION GRADE, IVORY COLORED DEVICES THROUGHOUT, UNLESS NOTED PROVIDE SPECIFICATION GRADE, IVORY COLORED DEVICES THROUGHOUT, UNLESS NOTED OTHERWISE ON THE PLANS. DEVICES SHALL BE HUBBELL. PLATES SHALL BE IVORY PLASTIC, WITH MATCHING SCREWS, UNLESS NOTED OTHERWISE. PROVIDE BLANK COVERPLATES FOR UNUSED OUTLETS. COVERPLATES FOR MULTI-GANG BOXES SHALL BE SIZED FOR THE BOX COVERED. 28. BRANCH CIRCUITS SHALL USE MINIMUM NO. 12 AWG WIRING. FOR DISTANCES EXCEEDING 75' BRANCH CIRCUITS SHALL USE MINIMUM NO. 12 AWG WIRING. FOR DISTANCES EXCEEDING 75' FROM THE PANEL, PROVIDE MIN. 10 AWG WIRING. CONTROL WIRING SHALL USE MINIMUM NO. 14 AWG WIRING. 29. DO NOT INSTALL EXPOSED CONDUIT UNLESS APPROVED BY THE ARCHITECT. DO NOT INSTALL EXPOSED CONDUIT UNLESS APPROVED BY THE ARCHITECT. 30. RUN ALL CONDUIT PARALLEL AND PERPENDICULAR TO BUILDING LINES. RUN ALL CONDUIT PARALLEL AND PERPENDICULAR TO BUILDING LINES. 31. USE FLEXIBLE METALLIC CONDUIT FOR CONNECTIONS TO MOTORS, FIXTURES, OR OTHER USE FLEXIBLE METALLIC CONDUIT FOR CONNECTIONS TO MOTORS, FIXTURES, OR OTHER EQUIPMENT WHERE VIBRATION IS PRESENT. PROVIDE SEALTITE FMC IN WET AREAS. 32. PROVIDE GROUND WIRE IN NON-METALLIC CONDUIT AND FLEXIBLE CONDUIT. GROUND WIRES PROVIDE GROUND WIRE IN NON-METALLIC CONDUIT AND FLEXIBLE CONDUIT. GROUND WIRES SHALL BE INCREASED IN SIZE WHERE CIRCUIT WIRING IS INCREASED FOR VOLTAGE DROP. 33. PROVIDE A TYPED PANEL SCHEDULE FOR EACH PANEL, INSERTED IN A PLASTIC SLEEVE.PROVIDE A TYPED PANEL SCHEDULE FOR EACH PANEL, INSERTED IN A PLASTIC SLEEVE.

AutoCAD SHX Text

ELECTRICAL GENERAL NOTES

AutoCAD SHX Text

GENERAL ELECTRICAL ABBREVIATIONS

AutoCAD SHX Text

ELECTRIC SERVICE METER

AutoCAD SHX Text M

AutoCAD SHX Text S

AutoCAD SHX Text

SMOKE DETECTOR (CEILING MOUNTED)

AutoCAD SHX Text S

AutoCAD SHX Text

SMOKE DETECTOR WITH CARBON MONOXIDE (CEILING MOUNTED)

AutoCAD SHX Text

CO

AutoCAD SHX Text

BUILDING CODE DATA

AutoCAD SHX Text

DISCIPLINE

AutoCAD SHX Text

EDITION

AutoCAD SHX Text

INTERNATIONAL BUILDING CODE

AutoCAD SHX Text

GENERAL

AutoCAD SHX Text

AutoCAD SHX Text

CODE

AutoCAD SHX Text

INTERNATIONAL MECHANICAL CODE

AutoCAD SHX Text

HVAC / MECHANICAL

AutoCAD SHX Text

INTERNATIONAL PLUMBING CODE

AutoCAD SHX Text

PLUMBING

AutoCAD SHX Text

NATIONAL ELECTRIC CODE

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

INTERNATIONAL FIRE CODE

AutoCAD SHX Text

NFPA STANDARDS

AutoCAD SHX Text

FIRE PROTECTION

AutoCAD SHX Text

CURRENT

AutoCAD SHX Text

INTERNATIONAL FUEL GAS CODE

AutoCAD SHX Text

FUEL

AutoCAD SHX Text

INTERNATIONAL ENERGY CONSERVATION CODE

AutoCAD SHX Text

ENERGY

AutoCAD SHX Text

ICC/ANSI A117.1

AutoCAD SHX Text

ACCESSIBILITY

AutoCAD SHX Text NOTES: A. ALL WORK PERFORMED SHALL COMPLY WITH THE REQUIREMENTS OF THE LISTED CODES, LOCAL ALL WORK PERFORMED SHALL COMPLY WITH THE REQUIREMENTS OF THE LISTED CODES, LOCAL CODE AMENDMENTS, AND REFERENCED STANDARDS AS ENFORCED BY THE AUTHORITY HAVING JURISDICTION (AHJ). B. ALL WORK SUBJECT TO INSPECTION BY THE AHJ AT THE PROJECT SITE FOR COMPLIANCE.ALL WORK SUBJECT TO INSPECTION BY THE AHJ AT THE PROJECT SITE FOR COMPLIANCE.

AutoCAD SHX Text

CITY OF BLACK HAWK MUNICIPAL CODE

AutoCAD SHX Text

LOCAL AMENDMENTS

AutoCAD SHX Text

CURRENT

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

GENERATOR SPECIFICATIONS

AutoCAD SHX Text E0.4

AutoCAD SHX Text

SITE ELECTRICAL PLAN

AutoCAD SHX Text E1.0

AutoCAD SHX Text

GENERATOR SPECIFICATIONS

AutoCAD SHX Text E0.5

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text

100% CD SET

AutoCAD SHX Text

AutoCAD SHX Text

GILPIN COUNTY JUSTICE CENTER

AutoCAD SHX Text

2960 DORY HILL RD #200

AutoCAD SHX Text

BLACK HAWK, CO 80422

AutoCAD SHX Text

GILPIN COUNTY

AutoCAD SHX Text O

AutoCAD SHX Text D

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text L

AutoCAD SHX Text O

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text G

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text N

AutoCAD SHX Text 62974

AutoCAD SHX Text W

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text

AutoCAD SHX Text H

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text N

AutoCAD SHX Text G

SHEET TITLE:

NOTICE: DUTY OF COOPERATION Release of these plans contemplates further coordination among the owner, his contractor(s), the architect and engineers. Design and construction are complex. Although the architect and his consultants have performed their services with due care and diligence, they cannot guarantee perfection. Communication is imperfect, and every contingency cannot be anticipated. Any ambiguity or discrepancy discovered by the use of these plans shall be reported immediately to the architect. Failure to notify the architect compounds misunderstanding and increases construction costs. A failure to cooperate by a notice to the architect shall relieve the architect/engineer from responsibility for all consequences. Changes made from the plans without consent of the architect are unauthorized, and shall relieve the architect/engineer of responsibility for all consequences caused by such changes.

REVISIONS

DATE DESCRIPTION NO.

323 3RD AVENUE, #100

TEL: 1.303.678.1108

LONGMONT, CO 80501

BOWMAN.COM

Bowman

PROJECT NO.:

DRAWN BY:

PM:

230548J

CHECKED BY/CC:

EOR:

ELECTRICAL

RISER DIAGRAM

E0.2

WN AP

WNBE

AutoCAD SHX Text #3/0 CU GROUND WATER PIPE #3/0 CU BUILDING STEEL #4 CU GROUND UFER #6 CU GROUNDING ROD

AutoCAD SHX Text M

AutoCAD SHX Text

EXISTING UTILITY METER

AutoCAD SHX Text

EXISTING 'MDP', 1600A, 277/480V, 3P, 4W, 65KAIC

AutoCAD SHX Text

BUILDING FEED BY UTILITY 480V 3 PH 4W

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

AutoCAD SHX Text

ELECTRICAL RISER DIAGRAM - DEMOLITION PLAN

AutoCAD SHX Text

NONE

AutoCAD SHX Text 1600A/3P

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

EXISTING 600A ATS-EM 277/480V 3

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

PANEL 'EH-3' 100A 277/480V 3

AutoCAD SHX Text

EXISTING 'EM MDP', 600A, 277/480V, 3P, 4W, 65KAIC

AutoCAD SHX Text 100/4

AutoCAD SHX Text 20/4

AutoCAD SHX Text

TO EXISTING JOCKEY PUMP

AutoCAD SHX Text

30AS 6AF 3

AutoCAD SHX Text

30A 3 SPARE

AutoCAD SHX Text

100AS 100AF 3

AutoCAD SHX Text

PANEL 'EL-2' 200A 120/208V 3

AutoCAD SHX Text 60/3

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

PANEL 'L3' 200A 120/208V 3

AutoCAD SHX Text 100/3

AutoCAD SHX Text

100AS 100AF 3

AutoCAD SHX Text

PANEL 'EH-2' 100A 277/480V 3

AutoCAD SHX Text 125/4

AutoCAD SHX Text

100AS 90AF 3

AutoCAD SHX Text

PANEL 'KL1' 200A 120/208V 3

AutoCAD SHX Text 125/3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'EH-1' 200A 277/480V 3

AutoCAD SHX Text 600/4

AutoCAD SHX Text 600/4

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 200/4

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text 200/4

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text 125/4

AutoCAD SHX Text 200A 3

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

100A 3 SPARE

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

TO EXISTING CHILLER

AutoCAD SHX Text 100/4

AutoCAD SHX Text

TO EXISTING PUMP/CHLOR STA

AutoCAD SHX Text

PANEL 'H-4' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-3' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-2' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-1' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

EXISTING 'MDP' SECTION, 1200A, 277/480V, 3P, 4W, 65KAIC

AutoCAD SHX Text 600A/3P

AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

1. CONTRACTOR SHALL BE RESPONSIBLE TO VERIFY CONDITION CONTRACTOR SHALL BE RESPONSIBLE TO VERIFY CONDITION AND PROPER FUNCTIONALITY OF ALL SYSTEMS AND DEVICES WHICH ARE INVOLVED OR AFFECTED BY THE SCOPE OF THIS PROJECT PRIOR TO BEGINNING WORK. ALL DAMAGE OR IMPROPER FUNCTIONALITY SHALL BE REPORTED TO OWNER IN WRITING. UNDOCUMENTED DAMAGE OR IMPROPER FUNCTIONALITY DISCOVERED FOLLOWING THE START OF WORK SHALL BE CORRECTED AT CONTRACTORS EXPENSE TO APPROVAL OF OWNER. 2. CONTRACTOR SHALL TRACE AND VERIFY ALL RELATED CONTRACTOR SHALL TRACE AND VERIFY ALL RELATED CIRCUITING PRIOR TO BEGINNING WORK. PANEL SCHEDULES FOR EXISTING PANELS SHOWN SHALL BE UPDATED TO REFLECT REVISED CONDITIONS. 3. CIRCUIT NUMBERS SHOWN ARE SHOWN FOR DESIGN INTENT CIRCUIT NUMBERS SHOWN ARE SHOWN FOR DESIGN INTENT ONLY. CONTRACTOR SHALL VERIFY BREAKER AVAILABILITY IN EXISTING PANEL FOR SIZES AND TYPES INDICATED AND PROVIDE NEW BREAKERS TO MEET DESIGN INTENT. PANEL SCHEDULE SHALL BE UPDATED TO REFLECT REVISED CONDITIONS. 4. DEVICES TAGGED 'EX' OR PREFIXED WITH (E) ARE EXISTING TO DEVICES TAGGED 'EX' OR PREFIXED WITH (E) ARE EXISTING TO REMAIN AND SHOWN FOR REFERENCE ONLY. DEVICES AND THEIR CONDUITS PREFIXED WITH (D) SHALL BE DEMOLISHED BACK TO THE ELECTRICAL PANEL FED FROM. 5. ELECTRICAL RISER DIAGRAM AND PANELS ARE BASED ON ELECTRICAL RISER DIAGRAM AND PANELS ARE BASED ON VISIBLE EXISTING SITE CONDITIONS AND EXISTING DRAWINGS. ELECTRICAL CONTRACTOR SHALL TRACE AND VERIFY ALL PERTINENT CIRCUITING PRIOR TO BEGINNING ANY WORK. PANEL SCHEDULES FOR EXISTING PANELS WITHIN THIS SCOPE OF WORK SHALL BE UPDATED TO REFLECT EXISTING CONDITIONS. ANY CHANGES OR DISCREPANCIES SHALL BE REPORTED TO THE EOR.

AutoCAD SHX Text

WORK NOTES:

AutoCAD SHX Text

1. EC TO INTERCEPT EXISTING CONDUCTOR AND CONDUITS. EC TO INTERCEPT EXISTING CONDUCTOR AND CONDUITS. CONFIRM FINAL LOCATION OF NEW JUNCTION BOX ON SITE. FINAL JUNCTION BOX SIZE SHALL BE CONFIRMED PER EXISTING CONDUIT SIZE AND COMPLY PER NEC 314.16. 2. NEW BUILDING MAIN AND EMERGENCY SERVICE DISCONNECTS, CT NEW BUILDING MAIN AND EMERGENCY SERVICE DISCONNECTS, CT AND UTILITY METER HOUSING SHALL BE IN A NEMA 3R ENCLOSURE LOCATED OUTSIDE OF THE BUILDING. REFER TO SITE PLAN FOR PROPOSED LOCATION. 3. EC TO VERIFY IF EXISTING FIRE PUMP ATS IS IN GOOD EC TO VERIFY IF EXISTING FIRE PUMP ATS IS IN GOOD OPERABLE CONDITION. OTHERWISE, REPLACE WITH A NEW ATS WITH EQUIL OR BETTER SPECIFICATIONS. 4. 6" HOUSEKEEPING PAD. 6" HOUSEKEEPING PAD. 5. NEW ATS SHALL COMPLY WITH ALL REQUIREMENTS SET FORTH NEW ATS SHALL COMPLY WITH ALL REQUIREMENTS SET FORTH IN NEC SECTION 702. 6. EC SHALL INSTALL NEW CONDUIT AND CONDUCTOR PRIOR TO EC SHALL INSTALL NEW CONDUIT AND CONDUCTOR PRIOR TO DISCONNECTION AND REMOVAL OF EXISTING ELECTRICAL. 7. NEW ATS AND MTS SHALL HAVE SWITCHING MEANS, INCLUDING NEW ATS AND MTS SHALL HAVE SWITCHING MEANS, INCLUDING THE INTERLOCKS, BE LISTED AND PROVIDED WITH MECHANICAL OR MECHANICAL AND ELECTRICAL INTERLOCKING TO PREVENT INADVERTENT INTERCONNECTION OF POWER SOURCES. SHALL COMPLY WITH ALL REQUIREMENTS SET FORTH IN NEC SECTION 700. 8. PROVIDE NEW CONDUCTORS BETWEEN EXISTING FIRE PUMP ATS PROVIDE NEW CONDUCTORS BETWEEN EXISTING FIRE PUMP ATS AND NEW GENERATOR.

AutoCAD SHX Text X

AutoCAD SHX Text

DEMOLITION NOTES:

AutoCAD SHX Text

1. REMOVE EXISTING CONDUCTORS BETWEEN FIRE PUMP ATS AND REMOVE EXISTING CONDUCTORS BETWEEN FIRE PUMP ATS AND EXISTING GENERATOR. 2. EXISTING SERVICE CT EQUIPMENT SECTION SHALL BE EXISTING SERVICE CT EQUIPMENT SECTION SHALL BE DEMOLISHED AFTER THE NEW MAIN SERVICE EQUIPMENT AND CT HAVE BEEN INSTALLED AND PUT INTO SERVICE. 3. EXISTING ATS-EM, CONDUIT, CONDUCTORS, AND EQUIPMENT EXISTING ATS-EM, CONDUIT, CONDUCTORS, AND EQUIPMENT RELATED TO 'EM MDP' PANEL SHALL BE DEMOLISHED AFTER THE 'EM MDP' PANEL IS BROUGHT BACK INTO SERVICE. 4. NEW GENERATOR SHALL BE CONSTRUCTED NEAR THE LOCATION NEW GENERATOR SHALL BE CONSTRUCTED NEAR THE LOCATION OF THE EXISTING GENERATOR AS THE CONSTRUCTION SHALL BE COMPLETED IN PHASES. DEMOLISH EXISTING GENERATOR, RELATED DEVICES, CONDUIT, CONDUCTORS AFTER NEW GENERATOR AND RELATED DEVICES ARE IN SERVICE. 5. EXISTING 600A MAIN DISCONNECT FOR THE 'EM MDP' PANEL EXISTING 600A MAIN DISCONNECT FOR THE 'EM MDP' PANEL SHALL BE MADE SPARE ONCE NEW SERVICE FEEDER IS IN SERVICE. 6. EC SHALL DEMOLISH EXISTING CONDUCTOR AND ABANDON EC SHALL DEMOLISH EXISTING CONDUCTOR AND ABANDON EXISTING UNDERGROUND CONDUIT FROM UTILITY TRANSFROMER AFTER NEW SERVICE IS IN SERVICE.

AutoCAD SHX Text X

AutoCAD SHX Text

(E)400KW DIESEL GENERATOR

AutoCAD SHX Text 1600/4

AutoCAD SHX Text 200/4

AutoCAD SHX Text 60/4

AutoCAD SHX Text

(E)400KW DIESEL GENERATOR

AutoCAD SHX Text 600/4

AutoCAD SHX Text

400KW 480V/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text

(D)DIESEL GENERATOR

AutoCAD SHX Text 600/3

AutoCAD SHX Text

TO FIRE PUMP ATS

AutoCAD SHX Text

TO EM MDP ATS

AutoCAD SHX Text

PANEL 'EL1' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

(E) 200AS 200AF 3

AutoCAD SHX Text

PANEL 'L1' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text 90/3

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/3

AutoCAD SHX Text

PANEL 'L2' 200A 120/208V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

(E) 200AS 200AF 3

AutoCAD SHX Text

PANEL 'L3' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text #3/0 CU GROUND WATER PIPE #3/0 CU BUILDING STEEL #4 CU GROUND UFER #6 CU GROUNDING ROD

AutoCAD SHX Text M

AutoCAD SHX Text

EXISTING 'MDP', 1600A, 277/480V, 3P, 4W, 65KAIC

AutoCAD SHX Text

BUILDING FEED BY UTILITY 480V 3 PH 4W

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

AutoCAD SHX Text

ELECTRICAL RISER DIAGRAM - PROPOSED PLAN

AutoCAD SHX Text

NONE

AutoCAD SHX Text 1600A/3P

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

PANEL 'EH-3' 100A 277/480V 3

AutoCAD SHX Text

EXISTING 'EM MDP', 600A, 277/480V, 3P, 4W, 65KAIC

AutoCAD SHX Text 100/4

AutoCAD SHX Text 20/4

AutoCAD SHX Text

TO EXISTING JOCKEY PUMP

AutoCAD SHX Text

30AS 6AF 3

AutoCAD SHX Text

30A 3 SPARE

AutoCAD SHX Text

100AS 100AF 3

AutoCAD SHX Text

PANEL 'EL-2' 200A 120/208V 3

AutoCAD SHX Text 60/3

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

PANEL 'L3' 200A 120/208V 3

AutoCAD SHX Text 100/3

AutoCAD SHX Text

100AS 100AF 3

AutoCAD SHX Text

PANEL 'EH-2' 100A 277/480V 3

AutoCAD SHX Text 125/4

AutoCAD SHX Text

100AS 90AF 3

AutoCAD SHX Text

PANEL 'KL1' 200A 120/208V 3

AutoCAD SHX Text 125/3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'EH-1' 200A 277/480V 3

AutoCAD SHX Text 600/4

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 200/4

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text 200/4

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text 125/4

AutoCAD SHX Text 200A 3

AutoCAD SHX Text 100A 3

AutoCAD SHX Text

100A 3 SPARE

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

TO EXISTING CHILLER

AutoCAD SHX Text 100/4

AutoCAD SHX Text

TO EXISTING PUMP/CHLOR STA

AutoCAD SHX Text

PANEL 'H-4' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-3' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-2' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

PANEL 'H-1' 200A 277/480V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

600A/3P SPARE

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

(E)200A FIRE PUMP ATS 277/480V 3

AutoCAD SHX Text

(N)400KW DIESEL GENERATOR

AutoCAD SHX Text

(E)FIRE PUMP DISC. 200AS 200AF 3

AutoCAD SHX Text

(E)FIRE PUMP CONTROLLER

AutoCAD SHX Text

(E)25HP FIRE PUMP

AutoCAD SHX Text 1600/S

AutoCAD SHX Text 200/S

AutoCAD SHX Text 200/4

AutoCAD SHX Text 60/4

AutoCAD SHX Text 60/4

AutoCAD SHX Text

400KW 480V/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text

NEW DIESEL GENERATOR

AutoCAD SHX Text 600/3

AutoCAD SHX Text

TO FIRE PUMP ATS

AutoCAD SHX Text

TO EM MDP ATS

AutoCAD SHX Text

PANEL 'EL1' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text M

AutoCAD SHX Text

EXISTING UTILITY METER: 1598005

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

200AS 200AF 3

AutoCAD SHX Text

(E) 200AS 200AF 3

AutoCAD SHX Text

PANEL 'L1' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text 90/3

AutoCAD SHX Text

75 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/3

AutoCAD SHX Text

PANEL 'L2' 200A 120/208V 3

AutoCAD SHX Text 200/4

AutoCAD SHX Text

(E) 200AS 200AF 3

AutoCAD SHX Text

PANEL 'L3' 100A 120/208V 3

AutoCAD SHX Text

45 KVA XFMR 480V 208V

AutoCAD SHX Text

#4 GND (TYP. 3)

AutoCAD SHX Text 125/4

AutoCAD SHX Text 60/3

AutoCAD SHX Text 60/3

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

(N)JUNCTION (SPLICE) BOX

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

NEW 'MDP-MAIN', 1600A, 277/480V, 3P, 4W, 65KAIC, NEMA 3R

AutoCAD SHX Text

NEW UTILITY METER HOUSING

AutoCAD SHX Text

AutoCAD SHX Text 1600A/3P

AutoCAD SHX Text

GFI

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

(N)600A EM MDP ATS 277/480V,3 NEMA 3R 35 KAIC

AutoCAD SHX Text

(N)400KW DIESEL GENERATOR

AutoCAD SHX Text

AutoCAD SHX Text 600/4

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

(N)600A EM MDP MTS 277/480V,3 NEMA 3R 35KAIC

AutoCAD SHX Text

AutoCAD SHX Text

TO PORTABLE GENERATOR POWER INLET BOX

AutoCAD SHX Text 600/4

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

(N)1600A MDP ATS 277/480V,3 NEMA 3R 35KAIC

AutoCAD SHX Text

AutoCAD SHX Text 600A/3P

AutoCAD SHX Text 1600/4

AutoCAD SHX Text

(N)400KW DIESEL GENERATOR

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

47 HOURS OF RUN TIME

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

6. REFER TO SITE PLAN FOR PROPOSED LOCATION OF NEW REFER TO SITE PLAN FOR PROPOSED LOCATION OF NEW EQUIPMENT. COORDINATE WITH GC TO DETERMINE IF LOCATION IS SUITABLE, NOTIFY THE EOR IF EQUIPMENT NEEDS TO BE RELOCATED TO A DIFFERENT LOCATION DUE TO POTENTIAL ISSUES RELATED TO MEANS AND METHOD. 7. ANY SPRINKLER LINES OR HEADS, GAS LINES, OR OTHER ANY SPRINKLER LINES OR HEADS, GAS LINES, OR OTHER UNDERGROUND INFRASTRUCTURE OR UTILITY LINES DAMAGED DURING CONSTRUCTION OF THIS PROJECT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO REPAIR AT THE CONTRACTOR'S EXPENSE. 8. CONSTRUCTION PHASING IS REQUIRED TO MINIMIZE TIME OF CONSTRUCTION PHASING IS REQUIRED TO MINIMIZE TIME OF NORMAL POWER SHUTOFF. COORDINATION EFFORT AND PLANNING IS REQUIRED WITH OWNER REPRESENTATIVE PRIOR TO ANY WORK PERFORMED ON SITE. 9. ALL EXISTING EQUIPMENT WITHOUT HATCHING INDICATES ALL EXISTING EQUIPMENT WITHOUT HATCHING INDICATES EXISTING TO REMAIN AND SHOWN FOR REFERENCE ONLY. ALL NEW WORK SHOWN IN THICK LINE TYPE. 10. SELECTIVE COORDINATION STUDY WILL BE PROVIDED BY SELECTIVE COORDINATION STUDY WILL BE PROVIDED BY OTHERS. 11. EC TO COORDINATE ALL NEW WORK WITH LOCAL UTILITY AND EC TO COORDINATE ALL NEW WORK WITH LOCAL UTILITY AND PROVIDE AN INSTALLATION PLAN WITH CONSTRUCTION PHASING PLAN AS SOON AS POSSIBLE.

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 600/4

AutoCAD SHX Text 1600/4

AutoCAD SHX Text

AutoCAD SHX Text N

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text

(E)200A FIRE PUMP ATS 277/480V 3

AutoCAD SHX Text

(E)FIRE PUMP DISC. 200AS 200AF 3

AutoCAD SHX Text

(E)FIRE PUMP CONTROLLER

AutoCAD SHX Text

(E)25HP FIRE PUMP

AutoCAD SHX Text 200/4

AutoCAD SHX Text 60/4

AutoCAD SHX Text M

AutoCAD SHX Text

EXISTING UTILITY METER: 1598005

AutoCAD SHX Text

(N)JUNCTION (SPLICE) BOX

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 1600/4

AutoCAD SHX Text 600/4

AutoCAD SHX Text 60/4

AutoCAD SHX Text 1600/3

AutoCAD SHX Text

TO MDP ATS

AutoCAD SHX Text 1600/4

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text

100% CD SET

AutoCAD SHX Text

AutoCAD SHX Text

GILPIN COUNTY JUSTICE CENTER

AutoCAD SHX Text

2960 DORY HILL RD #200

AutoCAD SHX Text

BLACK HAWK, CO 80422

AutoCAD SHX Text

GILPIN COUNTY

AutoCAD SHX Text O

AutoCAD SHX Text D

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text L

AutoCAD SHX Text O

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text G

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text N

AutoCAD SHX Text 62974

AutoCAD SHX Text W

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text

AutoCAD SHX Text H

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text N

SHEET TITLE:

NOTICE: DUTY OF COOPERATION Release of these plans contemplates further coordination among the owner, his contractor(s), the architect and engineers. Design and construction are complex. Although the architect and his consultants have performed their services with due care and diligence, they cannot guarantee perfection. Communication is imperfect, and every contingency cannot be anticipated. Any ambiguity or discrepancy discovered by the use of these plans shall be reported immediately to the architect. Failure to notify the architect compounds misunderstanding and increases construction costs. A failure to cooperate by a notice to the architect shall relieve the architect/engineer from responsibility for all consequences. Changes made from the plans without consent of the architect are unauthorized, and shall relieve the architect/engineer of responsibility for all consequences caused by such changes.

REVISIONS

DATE DESCRIPTION NO.

323 3RD AVENUE, #100

TEL: 1.303.678.1108

LONGMONT, CO 80501

BOWMAN.COM

Bowman

PROJECT NO.:

DRAWN BY:

PM:

230548J

CHECKED BY/CC:

EOR:

ELECTRICAL

PANEL

SCHEDULES

E0.3

WN AP

WNBE

AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

1. CONTRACTOR SHALL BE RESPONSIBLE TO VERIFY CONDITION CONTRACTOR SHALL BE RESPONSIBLE TO VERIFY CONDITION AND PROPER FUNCTIONALITY OF ALL SYSTEMS AND DEVICES WHICH ARE INVOLVED OR AFFECTED BY THE SCOPE OF THIS PROJECT PRIOR TO BEGINNING WORK. ALL DAMAGE OR IMPROPER FUNCTIONALITY SHALL BE REPORTED TO OWNER IN WRITING. UNDOCUMENTED DAMAGE OR IMPROPER FUNCTIONALITY DISCOVERED FOLLOWING THE START OF WORK SHALL BE CORRECTED AT CONTRACTORS EXPENSE TO APPROVAL OF OWNER. 2. CONTRACTOR SHALL TRACE AND VERIFY ALL CIRCUITING PRIOR CONTRACTOR SHALL TRACE AND VERIFY ALL CIRCUITING PRIOR TO BEGINNING WORK. PANEL SCHEDULES FOR EXISTING PANELS SHOWN SHALL BE UPDATED TO REFLECT REVISED CONDITIONS. 3. CIRCUIT NUMBERS SHOWN ARE SHOWN FOR DESIGN INTENT CIRCUIT NUMBERS SHOWN ARE SHOWN FOR DESIGN INTENT ONLY. CONTRACTOR SHALL VERIFY BREAKER AVAILABILITY IN EXISTING PANEL FOR SIZES AND TYPES INDICATED AND PROVIDE NEW BREAKERS TO MEET DESIGN INTENT. PANEL SCHEDULE SHALL BE UPDATED TO REFLECT REVISED CONDITIONS. 4. NOT ALL EXISTING PANELS REQUIRES NEW WORK. THEY ARE NOT ALL EXISTING PANELS REQUIRES NEW WORK. THEY ARE SHOWN FOR REFERENCES ONLY.

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text 11/08/24

AutoCAD SHX Text

100% CD SET

AutoCAD SHX Text

AutoCAD SHX Text

GILPIN COUNTY JUSTICE CENTER

AutoCAD SHX Text

2960 DORY HILL RD #200

AutoCAD SHX Text

BLACK HAWK, CO 80422

AutoCAD SHX Text

GILPIN COUNTY

AutoCAD SHX Text O

AutoCAD SHX Text D

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text L

AutoCAD SHX Text O

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text G

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text N

AutoCAD SHX Text 62974

AutoCAD SHX Text W

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text

AutoCAD SHX Text H

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text N

SHEET TITLE:

NOTICE: DUTY OF COOPERATION Release of these plans contemplates further coordination among the owner, his contractor(s), the architect and engineers. Design and construction are complex. Although the architect and his consultants have performed their services with due care and diligence, they cannot guarantee perfection. Communication is imperfect, and every contingency cannot be anticipated. Any ambiguity or discrepancy discovered by the use of these plans shall be reported immediately to the architect. Failure to notify the architect compounds misunderstanding and increases construction costs. A failure to cooperate by a notice to the architect shall relieve the architect/engineer from responsibility for all consequences.