2.2.1 RFQ Synopsis Solicitation-Pltoon Support Vehicle_08.02.2022.docx

Request for Quote

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation. The solicitation number is 70US0922R70092545 and is issued as a Request for Quote (RFQ) for Public Order Platoon Support Vehicle. This requires vendor to provide a custom platoon support vehicle to provide response to high security areas that the US Secret Service is responsible for protecting and provide support for National Special Security Events as directed by the director of the USSS.

The solicitation document and incorporated provisions and clauses are those in effect through the Federal Acquisition Circular 2022-06 effective April 26, 2022. This solicitation is open market and the associated North American Industry Classification System (NAICS) code 336120, Heavy Duty Truck Manufacturing, and PSC code 4240, Safety and Rescue Equipment. The anticipated Period of Performance is September 01, 2022, to August 31, 2023. The Government intends to award a firm fixed price (Purchase Order) for a One (1) year contract from this solicitation.

FAR 52.212-1 Instructions to Offerors - Commercial Items. (NOV 2021) is applicable to this solicitation.

FAR 52.212-2, Evaluation-Commercial Products and Commercial Services (NOV 2021) and the specific evaluation criteria to be included in paragraph (a) of that provision is applicable to this solicitation.

(a) The Government will award a contract resulting from this solicitation to the responsible offeror whose offer conforming to the solicitation will be most advantageous to the Government, price and other factors considered. The following factors shall be used to evaluate offers: (i) direct service (ii) vendor experience; (iii) service schedule; and (iv) price.

All proposal will be evaluated on a Best Value (Trade off) criteria basis. Evaluation weight is based on the technical factors (1 and 2) over price/cost (3). Technical factors will be weighed based on the quality of submission (provided all requested elements) versus the minimum requirement. Technical factors are listed in order of with the following weightings:

A completed copy of the provision FAR 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services (NOV 2021) must be included with Offeror’s proposal. If you have completed the annual representations and certifications electronically through the System for Award Management (SAM), then provide a statement as such and it shall be verified.

FAR 52.212-4, Contract Terms and Conditions-Commercial Products and Commercial Services (NOV 2021), applies to this acquisition. Potential offerors are hereby notified that the solicitation and subsequent amendments to the solicitation shall only be available by downloading the documents at the SAM Website at https://sam.gov. By submitting a response to this solicitation, the vendor shall be self-certifying that neither the offeror nor the principal corporate officials and owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any Federal Agency.

Part 1

Statement Of Work-Platoon Support Vehicle (HAVOC)

1. INTRODUCTION: The United States Secret Service Uniformed Division (USSSUD) Civil Disturbance Unit (CDU) provides Public Order Policing / crowd management and crowd control capabilities in a rapid deployable team to the White House Complex (WHC) the Vice President Residence (VPR) Foreign diplomatic locations in and around the National Capital Region (NCR) that are under USSSUD protection. The CDU is charged with monitoring, coordinating and facilitating 1st amendment activities as well as responding to spontaneous protest to include violent disorder

1.1 Background: Requirements of this custom vehicle is to provide command and control to 1st amendment gatherings. Provide support to crowd management tasking and support intermediate and advanced public order response teams to serious disorder as well as rehabilitation location for the CDU teams.

1.2 Objectives:

· Provide a rapid response to high security areas The Secret Service is responsible for protecting. These locations include but not limited to The White House, Vice Presidents residence, Foreign Embassies in the NCR.

· Provide response and support for National Special Security Events as directed by the director of the USSS.

· Provide Mutual Aid assistance to U.S. Capitol Police and the Capitol grounds, U.S. Park Police and the national icon monuments they are entrusted to protect as well as DC Metropolitan Police and their public safety mission for the city of Washington DC.

1.3 Scope: The Public Order Platoon Support vehicle (HAVOC). The contractor will provide the government a custom single axel walk-in rescue vehicle with compartments specifically designed to properly store and transport a specific amount of Intermediate and Advance Public Order Equipment. This equipment will include but not limited to protective shields / equipment, de contamination equipment, less lethal use of force systems, chemical munitions, forcible entry equipment, a command module for on scene commanders and the ability to safety transport eight (8) Officers.

1.4. Specific Tasks: HAVOC will consist of a custom single axel walk-in rescue vehicle similar to apparatus utilized by the fire service. This vehicle will consist of a cab over three (3) door design chassis with an appropriately sized walk-in rescue body to accomplish the requirements listed. This vehicle should have the smallest footprint / wheelbase possible while meeting the listed requirements. There are currently no height restrictions to this project. Even though this apparatus is being designed as a Law Enforcement vehicle attention shall be paid to and complied with NFPA 1901 safety guidelines for fire apparatus with the exception to graphics.

1.4.1. Task Heading.

Salient Characteristics:

· Stainless Steel Body

· 34’ LOA

· 3 Door Raised 20” Roof Cab

· 12” extended front bumper

· NFPA 1901 compliant

· Seating for 6 Passengers in Walk in Box

· Paint Color matte black

Salient Characteristics:

· Warn Series 15 15,000 lb with 100’ 7/16” synthetic rope

· powder coated galvanized rails

· Frame liner galvanized and powder coated

· GEOMET coated frame assembly fasteners

· 31,000 lb single rear axle

· Adjustable shock absorbers

· 21,500 lb front axle

· Stemco oil seal front axle. Chicago Rawhide seal with stemco sight glass will be supplied when front disc brakes are selected.

· Air Ride rear suspension

· Aluminum front wheels (black) (2)

· Aluminum rear wheels (black) (4)

· Goodyear highway tread tires

· LED tire pressure monitoring

· Front disc brakes

· Rear drum brakes

· Parking brake release on driver’s dash

· Electronic stability control

· Jacobs engine break

· Inlet for air system – driver’s door jab

· Nylon air lines

· Emergency air horn bypass in drivers’ compartment

· Studder tone horns in bumper

· Isolated air tank

· Auxiliary air tank for on board air

· Air dryer

· Diesel Engine (min 450hp)

· Automatic Transmission

· Push button transmission shift selector

· 65-gallon fuel tank

· Electric fuel pump

· 420-amp Alternator

· Front and rear tow eyes (black)

· Thermic fan clutch

· Driveline 1710

· Driveline guards (as applicable)

· Diesel Exhaust fluid (DEF)5 gallon tank

· Radiator mounted power steering cooler

· Class 3 trailer hitch – rear

· 7-pin trailer harness

· On spot chain system

· NFPA Black reflective striping

· Cab and box electric door locks

· Touch pad lock control at driver’s door

· Barrel style locks at all compartments keyed the same

· Power drivers and passenger windows

· Black handrails

· Door mounted west coast style remote heated mirror

· 10” convex mirror passenger side

· Electronic controlled HVAC

· Separate HVAC for rescue body

· Drivers and Passengers air ride seat

· Seat color black

· Seating capacity tag of eight occupants

· Roll up doors – barrel key separate

· To be located in command compartment and outside accessible

· Upper vista area cabinet. Cabinet to be full width and height of Vista area forward of rear cab doors. Includes (3) horizontal hinged lift-up doors.

· Medical cabinet(s) interior finish and components (shelve/trays) to match cab finish

· Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll-up door and (3) adjustable shelves.

· Heavy duty cab engine / overhead covering

· Cup holders

· USB charging ports

· Passenger command desk

· Panasonic Toughbook dock

· Interior color black

· Auto eject 120v battery charger with auto transfer

· USSS supplied Tri-Band antenna x2 mounted on roof

· 12v power point x6

· Auxiliary air compressor

· Red / white dome lights

· AM/FM with Aux input stereo with speakers

· Map light on passenger side

· Sun Visors- Driver and officer’s side overhead

· Traverse riser height area for use with exterior height compartments and no riser provided on rear wall

· Severe duty overhead console. Includes driver, center and officer overhead of air conditioning plenum. Center overhead include siren mounting locations. Overhead to match cab interior.

· Reduced profile rear engine cover for increased leg room

· Severe duty dash package with low profile center section. Cast alum construction. Includes smooth plate alum lower kick panels; all painted to match cab interior.

· Cab insulation package. Include insulation for ceiling, front wall, rear wall, side walls, below seat risers and in doors

· Rear Body Panels to be painted smooth plate.

· Seat Belts will be located on each seat on the Officers side of the interior

· Command desk with locking draws

· Dry erase boards (2)

· Red / white dome lights

· USB chargers

· 120v outlets

· Raceway to roof – watertight

· Three (3) roof mounted tri band antennas wired to junction box – USSS Supplied

· Stainless steel

· All body panels to be black in color

· 19’ walk in rescue body

· 80” walk in rescue

· Seating for 6

· Double stainless steel rear doors

· Windows on each side of rescue body

· Air purification system

· Standalone HVAC

· Bench seat with ladder storage w/ two 20’ extension ladders

· Interior storage solutions with netted covering

· Six (6) electronic weapons racks / locks with master power in Command module and driver area.

· Weapons racks should be handcuff / claw type with barrel key override

· USB Chargers

· Escape hatch

· Electric automatic retract misting awning on passenger side

· Rear ladder for roof access

· Embossed diamond plate flat roof for 19’ WI Rescue body

· 19’ Walk-in Rescue Body Interior. Walk- in area with a 46” wide walkway, walkway floor with embossed aluminum treadplate with composite underlay. The Upper side walls and horizontal work surface areas shall be 14 GA brushed stainless steel, ceiling shall be 1/8” white reinforced glass fiber panels. Ceiling and wall insulation.

· Counter top for stainless steel walk-in rescue will be straight.

· Roof Mtd. A/C system. Cooling capacity of 15,000 BTU and heating capacity of 6,000 BTU

· All door locks to have key override

· Forward doors on each side to be roll up type

· Forward compartments should be designed to carry the following on each side.

· Eight (8) 6’ x 24” Public Order shields

· Six (6) 4’ x 24” Public Order shields

· Twenty-Four (24) 2’ round Public Order Shields

· Interior of compartment shall have rubberized coating

· Rear two compartments to have solid stainless-steel doors with secondary puck type lock hasp installed

· Adjustable shelving

· Auto fresh air power vent

· Soft “blast” panels for roof

· SCBA Bottle Storage on both sides for six (6) bottles

· Front light bar red / blue / white

· Side marking red / blue / white

· Headlight flasher

· Roto ray – blue

· Siren Whelen w/ power call and rumble

· Federal Q2B

· 360-degree ground lighting – coated black

· 360-degree LED flood lighting – coated black

· Rear backing flood light

· Roof mounted light tower

· Back up camera – automatic

· 360-degree camera with DVR in command module

· Diamond plate camera shield

· Raceway through roof from command module – watertight

· Back up alarm

· Two (2) 32” LED HD monitors

· Four (4) Streamlight Vulcan hand lights

· Headset to be utilized between driver, passenger, and rescue module.

· Wheel Chocks

· DOT Required Drive away Kit. Includes three warning triangular warning reflectors with carrying case.

· Handheld flashlight with vehicle mount system.

· Onan 15kw PTO 120/240 single phase

· 120 / 240v break box

· 120v outlets in rear compartments and rescue module on transfer switch

· Cord reel 200’ 10/3 w/ rollers

· Junction box

· Interior and exterior to be painted black to include mounted accessories

· Painted USA Flag on grill- subdued gray scale w/ blue line

· LINE-X cab interior

· LINE-X bumper, rub rails, grab rails and steps

· Reflective striping and lettering to be done in black

· 12” primary bordered by two 3” strip the height of vehicle

· Rear black reflective chevron striping

· Graphics drawing showing striping, lettering and logos

· USSS Supplied logos

· 10 year / 100,000 mile engine

· 5 year / 100,000 mile transmission

· Lifetime frame Structural Warranty

· 20 year/100,000 Mile Structural warranty for stainless steel body – statement of warranty.

· Meritor 5 year unlimited miles, parts and labor rear drive single or rear drive tandem axle warranty.

· The E-ONE supplied components of the vehicle shall meet the requirements of NFPA 1901,2016 edition.

· OAH. Unit has no overall height restrictions

· OAL. Unit has no overall length restrictions

· Equipment allowance on the apparatus shall be 8000lbs.

· Transmission to seek second gear when Jacobs engine brake or Telma Retarder is Engaged. N/A with Trans retarder.

· Wrap exhaust with thermal insulation tape from turbo down to the DPF(not including flex pipe if equipped). Includes the S/S tie wraps

· Cooling system for use with Typhoon, Cyclone and Quest chassis. For use with 2010-2021 EPA Engines. Includes coolant recovery system

· Fuel Shut off Valve. Location: one(1) at fuel tank.

· Fuel line rubber hose

· Fuel water separator Fuel Pro 382 (Cummins FH2309). Filter is top serviceable.

· Replaces manufacturer supplied fuel filter. For use with 2021 EPA Engines.

· Battery four group 31 100 CCA.

· Typhoon 3-door extended cab with radial wiper (80”)CA. Located rear door on officer side of cab

· Vista full height rear doors 20”. Note:

· Delete front vista roof windows

· Delete side vista roof windows ahead of rear doors.

· Delete rear vista roof windows.

· Delete upper rear door vista roof windows

· Delete side vista roof windows rearward of rear doors.

· Cab and body to have applicable manfactures logos.

· Rear crew cab doors in the medium position

· NFPA Required reflective striping on the cab doors to be dealer/customer applied.

· Cab door Locks- Electric. Includes drivers side exterior touchpad, (2) remote key fobs, barrel style keys lock on the exterior of each door and manual interior lock on each door.

· All cab exterior door to have CH751 locks.

· Cab door panels stainless steel. Includes upper and lower panels with seam below handrail.

· Anodize aluminum trim (black in color) on the bottom edge of the exterior cab compartment openings.

· Rear crew cab door window(s) with manual regulator(s). For use with new Typhoon cab and 100” wide cyclone cabs

· Driver and officer door windows to be power actuated with HD regulators. Switches to be located at center dash. For use with typhoon and 100” wide Cyclone cabs.

· Cab doors to extend down to cover lower step well.

· Lower steps to extend 3.5” past cab. For use with legacy Typhoon/Cyclone with barrier style door and 2019 Typhoon/ 100” wide cyclone with barrier style or extended door.

· Windows cab side fixed driver’s side.

· Windows Cab side fixed officer’s side.

· Cab roof mounted job color 3 sided light tower shield with 45 degree front slope.

· Pair of 18” handrails (black in color) located just behind driver and officer front door one each side

· Mud Flaps, front, black with E-ONE.

· Rear cab wall to be smooth 3/16’ aluminum plate. Cab wall to be finished painted to match the cab paint scheme.

· (1) 36” handrail located just behind rear door (ALS doors if equipped). Use for 3 door custom cabs

· Recessed fuel fill driver side wheel well

· Cab tilt switch and manual jack to be located: R1 low on forward wall

· Nylon black cargo net for interior compartment opening of the compartment open area on interior body above a compartment. Cargo net to have custom designed one-piece bar assembly and one step Velcro attachment process with footman loops shall be used opposite bar end: DS1, OS1,OS2

· Stainless steel rear fender panels painted job Color. Includes bolt-on stainless steel inner wheel well liners (not painted) and outer fenderettes.

· Rub Rail assemblies constructed of 2.5x2” black U.H.M.W. plastic. Bolt to the lower exterior edge of the apparatus body below the side of the body compartment doors. For use with large rescue body.

· Large radius cab wheel well. Includes bolt-on adjustable wheel well trim.

· Rubber fenderettes in place of standard fender

· Rear cab and vista glass (if so Equipped) to have dark tint IPOS. Glass to be smoked glass with 20% light transmittance (+/-10%. Includes all glass rearward of front cab doors.

· Window option for 3 cab door. Provide standard window option for rear door position in standard location. Locate: Driver side.

· Hansen knurled grip surface handrails shall be Black in place of standard clear anodized handrails on cab. Handrails shall be anodized black from the factory. Quantity to match the number of handrails on cab exterior.

· Battery Charger Kussmaul model 1200, 40 amp.

· Cab Headlights. Position: Lower

· Auto Transfer switch 120 volt. Includes 8 place breaker box. Allows all interior receptacles to be powered by either shore power or generator.

· 12 VDC(or 24VDC) electrical outlet wired battery. Locations: In Cab Driver, in cab officer side, drivers side dash, officer side dash, driver side rear cab wall

· English Dominant main cab gauge cluster

· ATC Override switch

· Auto Drain, Kussmaul 091-9-089-120V. For use with air compressor.

· USB charging ports wired battery Hot. Location: drivers side dash, officer side dash driver side rear cab wall

· Momentary DPF Regeneration override switch

· Pre-wired for installation of tire chains. Includes lock-out/safety rocker style switch.

· LED Cab Headlights

· Light EON LED mounted in riser height compartment

· Black Super Auto Eject Deluxe cover with bar graph, for the auto eject located gravel shield drivers side.

· TecNiq D07 LED Cab door step area lighting. Includes (2) lights at each door area. Lights to be switched with door ajar.

· Turn Signal TecNiq LED strip (PR) with clear lense and polished alum housing located between quad headlight bezels (New Typhoon and 100” wide Cyclone only.)

· Quad Headlight Bezels (4) black ipos. Include strip light mounting bezel between quad housing.

· Customer supplied cable. Route Customer supplied cable (must be new cable) leaving a service loop at each end. Terminating Locations, cable type and service loops size as to be specified by Sales. Quantity is per cable to be installed.

· Keyed compartment door latch with #1250 key. Locations: L4,R4

· Stainless Steel tall doors double 3-point vertical hinged painted. Locations: L4, R4

· Pull down bungee type straps for full height and high side roll-up door9s0 on body module. For use with OROM and AMDOR doors only.

· Body Exterior doors on compartments L4/R4 will have a stainless steel hasp/eyelet installed to secure the doors with a padlock. Brushed stainless steel scuff plate below the hasp to protect paint from damage.

· All exterior compartments on rescue body will have Unistrut in each compartment unless inapplicable.

· All interior walkway compartments on rescue body will have Unistrut in each compartment unless inapplicable.

· Handrails on the interior of the walk-in entrance doors. Handrails shall be powder coated black from the factory.

· Access ladder. Includes required step lights and additional hand rails if applicable

· E-One designed (3) SCBA bottle storage officer side rear wheel well offset forward with hinged door and push button latch

· E-One designed (2) SCBA bottle storage driver side rear wheel well offset forward with hinged door and push button latch. Door material is stainless steel painted job color. Hold Standard size SCBA Bottle, 20lbs ABC Extinguisher.

· E-One designed (2) SCBA bottle storage sized up for up to 6.8´diameter bottles. Locate driver side rearward above fuel pocket (door covers fuel pocket). Door material is stainless steel painted job color with a push button latch

· E-ONE designed Wheel well Chock storage compartment officer side rear wheel well offset rearward with hinged door and push button latch. Door wired to “Door open” indicator inside cab. Door material is stainless steel painted job color.

· V-MUX Electrical system for Pumper/tanker/rescue

· Vehicle data recorder-2009/2016 NFPA compliant. Includes occupant detection shown in multiplex display. E-ONE chassis only.

· HVAC Controlled through multiplex displays

· Vista IV display for V-MIUX electrical system. Location: Driver’s side engine cover

· NanoProtech corrosion inhibiting spray coating to be applied on all exposed electrical connection

· Hazard (Door ajar) light 2” LED Location: center overhead

· Warning light Whelen M6RC series Super LED (PR) red with clear lens.

· All warning lights to have black bezel ipo chrome where applicable.

· Warning light Whelen ION-T Series model TLI Super LED (PR) Color: Red / Blue with clear lense. Location : (1) each side NFPA/ULC required lower zone rear side facing.

· Warning Light Roto Ray LED with (3) blue lights with clear lense

· Warning Light: Whelen M6 series Linear Super LED (PR)

· Whelen MKEZ7 1.5” standard mount for front light bar (PR)

· Cab Light bar layout per customer specific requirements

· Light Bar Whelen Freedom IV Model F4X7 72” with 18 LED Modules Red / Blue / White.

· Federal Q2B siren

· Primary 200w electronic siren control is to be located center overhead console offset to driver side.

· Whelen SA315P electronic siren speaker mounted behind front bumper

· License plate light LED with Chrome housing located at the rear of the body

· Marker lights Britax LED amber/red Rubber housed mounted on the rear body corners angled down.

· Weldon auxiliary turn signal model 9186-8580 LED (PR)

· LED marker light cab and body package. E-ONE custom cab

· A switch plate interior lighting controls shall be located officer’s side interior walkway wall adjacent to door opening. It shall accommodate a quantity of 6 rocker switches. It will be illuminated and labeled per each switch’s function.

· There will be a pair of truck-lite, 4 inch diameter 12 volt LED lights with clear lenses which shall be RECESS mounted into the canopy area above the walk-in body doors. The lights shall be activated when the rear doors are opened.

· Compartment light ROM V4 LED for medical cabinet (EA)

· Compartment light package ROM v4 LED for large bodies.

· Ground Light Package TecNiq T440 4”LED -Large

· Step Light package body TecNiq

· There will be a pair of TecNiq model E08-LCR0-1, * inch diameter 12 volt recessed red/clear LED lights, Recess mounted into the ceiling of the walk-in body. Each lamp will be switched near the door opening.

· FireTech FT-GESM scene lights (PR) with black chrome flange (when required) and weatherproof connectors. Switch in cab (driver and officer side lights switched separately). Locate: (1) each side of body rear facing up high (below warning lights if equipped).

· Engine compartment light Optronics LED Series ILL22

· TecNiq LED backing lights (PR) model E60-WS20-1flush mount docking/backing light. Location: rear wheel well offset to rear

· Foot switch to control air horns and Q2B located driver’s side and officer side

· The switch for the door electric lock(s) to be located driver’s overhead

· Audible door ajar alarm wired through door ajar light.

· Alternating flasher for headlights.

· Pre-wire for trailer hitch, Includes stop, left turn, right turn, marker and ground wires

· 7 pin trailer wiring connecting.

· Lighted Bumper guide

· Dual USB charging port wired to battery hot. Location: inside walk-in body, in counter top raceway, below window, officer side and driver side

· Blue Seas 12V power distribution.

· Install E-ONE supplied HDMI receptacle and wiring.

· Breaker Box 12 place single phase. Includes main breaker.

· Fire Research Spectra 12V LED Model SPA-260-Q15 powder coated with black with surface mount. Location: forward upper body panel officer side and driver side. Rearward upper body panel officer side and drivers side.

· FireTech 75”12V brow light with integrated marker light and black housing. Include Switch assessable to driver.

· Night Scan Chief Whelen light tower with (4) 150 watt 12V Whelen Pioneer LED light heads. Control to be located next to breaker box. Tower to be located rear mounted side to side and hinged to driver.

· Receptacle household 20A/110V duplex 3-prong NEMA 5-20 with cover plate interior mounted wired to inlet receptacle. Location: In cab driver and officer side on 3X3 post rear facing just above engine cover, driver back wall of cab, and officer side rear compartment facedown low and rear wheel well offset forward

· Electric cord reel rewind switch. Switch located on wall near cord reel.

· Rollers, captive cord reel mounted on reel.

· Circle D wall/ mounting box. Mount at final or ship loose. For use with reel in or on L2 back wall up high offset forward.

· Duo-safety 20’ 2-section extension ladder 900A

· Manuals, Operator and service in digital format

· Approval Drawings- Standard

· Dash/Console panel layout approval drawings. Will be provided on purchased units prior to constructions

· Fire Apparatus Safety Guide published by FAMA, Latest edition.

TOTAL CONTRACT VALUE

TBD

1.5 General Information

1.5.1 Date of Delivery: Vehicle should be delivered to the government within 210 days from award of contract

1.5.2 Place of Delivery: James J. Rowley Training Center, Laurel Maryland. 9200 Powder Mill RD Laurel MD, 20708

1.5.3 Hours of Operation: The contractor is responsible for conducting business, between the hours of 0800 – 1600, Monday through Friday except Federal holidays or when the Government facility is closed due to local or national emergencies, administrative closings, or similar Government directed facility closings. N/A

1.5.4 Type of Contract: The Government will award a FFP Contract.

1.5.5.1 Privacy Act: Personnel who have access to Privacy Information shall adhere to the Privacy Act, Title 5 of the U.S. Code, Section 552a and applicable agency rules and regulations. N/A

1.5.5.2 Physical Security: The contractor shall be responsible for safeguarding all Government equipment, information and property provided for contractor use. At the close of each work period, Government facilities, equipment, and materials shall be secured. N/A

1.5.5.3 Key Personnel: The contractor shall provide a point of contact Sergeant Technician Scott Curry who shall be responsible for the delivery. Lieutenant Michael Stafford will be the alternate point of contact.

1.5.5.4 Identification of Contractor Employees N/A -

1.5.6. Contractor Travel N/A.

1.5.7 Other Direct Costs N/A

1.5.8 Data Rights N/A

1.5.9 Organizational Conflict of Interest: Contractor and subcontractor personnel performing work under this contract may receive, have access to or participate in the development of proprietary or source selection information (e.g., cost or pricing information, budget information or analyses, specifications or work statements, etc.) or perform evaluation services which may create a current or subsequent Organizational Conflict of Interests (OCI) as defined in FAR Subpart 9.5. The Contractor shall notify the Contracting Officer immediately whenever it becomes aware that such access or participation may result in any actual or potential OCI and shall promptly submit a plan to the Contracting Officer to avoid or mitigate any such OCI. The Contractor’s mitigation plan will be determined to be acceptable solely at the discretion of the Contracting Officer and in the event the Contracting Officer unilaterally determines that any such OCI cannot be satisfactorily avoided or mitigated, the Contracting Officer may affect other remedies as he or she deems necessary, including prohibiting the Contractor from participation in subsequent contracted requirements which may be affected by the OCI. N/A

PART 2

DEFINITIONS & ACRONYMS

2. DEFINITIONS AND ACRONYMS:

2.1. DEFINITIONS:

N/A

2.1.1. CONTRACTOR. A supplier or vendor awarded a contract to provide specific supplies or service to the Government. The term used in this contract refers to the prime.

2.1.2. CONTRACTING OFFICER (C.O.). A person with authority to enter into, administer, and or terminate contracts, and make related determinations and findings on behalf of the Government. Note: The only individual who can legally bind the Government.

2.1.3. DELIVERABLE. Anything that can be physically delivered, but may include non-manufactured things such as meeting minutes or reports.

2.1.4. KEY PERSONNEL. Contractor personnel that are evaluated in a source selection process and that may be required to be used in the performance of a contract by the Key Personnel listed in the SOW. When key personnel are used as an evaluation factor in best value procurement, an offer can be rejected if it does not have a firm commitment from the persons that are listed in the proposal.

2.1.5. PHYSICAL SECURITY. Actions that prevent the loss or damage of Government property.

2.2. ACRONYMS:

PART 3

GOVERNMENT FURNISHED PROPERTY, EQUIPMENT, AND SERVICES

N/A

3. GOVERNMENT FURNISHED ITEMS AND SERVICES:

3.1. Services N/A

3.2 Facilities N/A

3.3 Utilities N/A

3.4 Equipment N/A

3.5 Materials N/A

(End of Statement of Work)

PROVISIONS

52.204-22 Alternative Line-Item Proposal. (Jan 2017)

(a) The Government recognizes that the line items established in this solicitation may not conform to the Offeror’s practices. Failure to correct these issues can result in difficulties in acceptance of deliverables and processing payments. Therefore, the Offeror is invited to propose alternative line items for which bids, proposals, or quotes are requested in this solicitation to ensure that the resulting contract is economically and administratively advantageous to the Government and the Offeror.

(b) The Offeror may submit one or more additional proposals with alternative line items, provided that alternative line items are consistent with subpart 4.10 of the Federal Acquisition Regulation. However, acceptance of an alternative proposal is a unilateral decision made solely at the discretion of the Government. Offers that do not comply with the line items specified in this solicitation may be determined to be nonresponsive or unacceptable.

(End of provision)

52.204-24 Representation Regarding Certain Telecommunications and Video Surveillance Services or Equipment. (AUG 2020)

The Offeror shall not complete the representation at paragraph (d)(1) of this provision if the Offeror has represented that it “does not provide covered telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument” in the provision at 52.204-26, Covered Telecommunications Equipment or Services—Representation, or in paragraph (v) of the provision at 52.212-3, Offeror Representations and Certifications-Commercial Items.

(a) Definitions. As used in this provision— Backhaul, covered telecommunications equipment or services, critical technology, interconnection arrangements, reasonable inquiry, roaming, and substantial or essential component have the meanings provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

(b) Prohibition.

(1) Section 889(a)(1)(A) of the John S. McCain National Defense Authorization Act for Fiscal Year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2019, from procuring or obtaining, or extending or renewing a contract to procure or obtain, any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. Nothing in the prohibition shall be construed to—

(i) Prohibit the head of an executive agency from procuring with an entity to provide a service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements; or

(ii) Cover telecommunications equipment that cannot route or redirect user data traffic or cannot permit visibility into any user data or packets that such equipment transmits or otherwise handles.

(2) Section 889(a)(1)(B) of the John S. McCain National Defense Authorization Act for Fiscal Year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2020, from entering into a contract or extending or renewing a contract with an entity that uses any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. This prohibition applies to the use of covered telecommunications equipment or services, regardless of whether that use is in performance of work under a Federal contract. Nothing in the prohibition shall be construed to—

(i) Prohibit the head of an executive agency from procuring with an entity to provide a service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements; or

(ii) Cover telecommunications equipment that cannot route or redirect user data traffic or cannot permit visibility into any user data or packets that such equipment transmits or otherwise handles.

(c) Procedures. The Offeror shall review the list of excluded parties in the System for Award Management (SAM) (https://www.sam.gov) for entities excluded from receiving federal awards for “covered telecommunications equipment or services”.

(d) Representation. The Offeror represents that—

(1) It □ will, □ will not provide covered telecommunications equipment or services to the Government in the performance of any contract, subcontract or other contractual instrument resulting from this solicitation. The Offeror shall provide the additional disclosure information required at paragraph (e)(1) of this section if the Offeror responds “will” in paragraph (d)(1) of this section; and

(2) After conducting a reasonable inquiry, for purposes of this representation, the Offeror represents that— It □ does, □ does not use covered telecommunications equipment or services, or use any equipment, system, or service that uses covered telecommunications equipment or services. The Offeror shall provide the additional disclosure information required at paragraph (e)(2) of this section if the Offeror responds “does” in paragraph (d)(2) of this section.

(e) Disclosures.

(1) Disclosure for the representation in paragraph (d)(1) of this provision. If the Offeror has responded “will” in the representation in paragraph (d)(1) of this provision, the Offeror shall provide the following information as part of the offer:

(i) For covered equipment—

(A) The entity that produced the covered telecommunications equipment (include entity name, unique entity identifier, CAGE code, and whether the entity was the original equipment manufacturer (OEM) or a distributor, if known);

(B) A description of all covered telecommunications equipment offered (include brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); and

(C) Explanation of the proposed use of covered telecommunications equipment and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(1) of this provision.

(ii) For covered services—

(A) If the service is related to item maintenance: A description of all covered telecommunications services offered (include on the item being maintained: Brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); or

(B) If not associated with maintenance, the Product Service Code (PSC) of the service being provided; and explanation of the proposed use of covered telecommunications services and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(1) of this provision.

(2) Disclosure for the representation in paragraph (d)(2) of this provision. If the Offeror has responded “does” in the representation in paragraph (d)(2) of this provision, the Offeror shall provide the following information as part of the offer:

(i) For covered equipment—

(A) The entity that produced the covered telecommunications equipment (include entity name, unique entity identifier, CAGE code, and whether the entity was the OEM or a distributor, if known);

(B) A description of all covered telecommunications equipment offered (include brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); and

(C) Explanation of the proposed use of covered telecommunications equipment and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(2) of this provision.

(ii) For covered services—

(A) If the service is related to item maintenance: A description of all covered telecommunications services offered (include on the item being maintained: Brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); or

(B) If not associated with maintenance, the PSC of the service being provided; and explanation of the proposed use of covered telecommunications services and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(2) of this provision.

(End of provision)

52.204-26 Covered Telecommunications Equipment or Services-Representation (DEC 2019)

(a) Definitions. As used in this provision, “covered telecommunications equipment or services” has the meaning provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

(b) Procedures. The Offeror shall review the list of excluded parties in the System for Award Management (SAM) (https://www.sam.gov) for entities excluded from receiving federal awards for “covered telecommunications equipment or services”.

(c) Representation. The Offeror represents that it □ does, □ does not provide covered telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument.

(End of provision)

52.225-25 Prohibition on Contracting With Entities Engaging in Certain Activities or Transactions Relating to Iran—Representation and Certifications. (Jun 2020)

(a) Definitions. As used in this provision- Person—

(1) Means–

(i) A natural person;

(ii) A corporation, business association, partnership, society, trust, financial institution, insurer, underwriter, guarantor, and any other business organization, any other nongovernmental entity, organization, or group, and any governmental entity operating as a business enterprise; and

(iii) Any successor to any entity described in paragraph (1)(ii) of this definition; and

(2) Does not include a government or governmental entity that is not operating as a business enterprise.

Sensitive technology-

(1) Means hardware, software, telecommunications equipment, or any other technology that is to be used specifically-

(i) To restrict the free flow of unbiased information in Iran; or

(ii) To disrupt, monitor, or otherwise restrict speech of the people of Iran; and

(2) Does not include information or informational materials the export of which the President does not have the authority to regulate or prohibit pursuant to section 203(b)(3) of the International Emergency Economic Powers Act ( 50 U.S.C. 1702(b)(3)).

(b) The offeror shall e-mail questions concerning sensitive technology to the Department of State at CISADA106@state.gov.

(c) Except as provided in paragraph (d) of this provision or if a waiver has been granted in accordance with Federal Acquisition Regulation (FAR) 25.703-4, by submission of its offer, the offeror—

(1) Represents, to the best of its knowledge and belief, that the offeror does not export any sensitive technology to the government of Iran or any entities or individuals owned or controlled by, or acting on behalf or at the direction of, the government of Iran;

(2) Certifies that the offeror, or any person owned or controlled by the offeror, does not engage in any activities for which sanctions may be imposed under section 5 of the Iran Sanctions Act. These sanctioned activities are in the areas of development of the petroleum resources of Iran, production of refined petroleum products in Iran, sale and provision of refined petroleum products to Iran, and contributing to Iran's ability to acquire or develop certain weapons or technologies; and

(3) Certifies that the offeror, and any person owned or controlled by the offeror, does not knowingly engage in any transaction that exceeds the threshold at FAR 25.703-2(a)(2) with Iran's Revolutionary Guard Corps or any of its officials, agents, or affiliates, the property and interests in property of which are blocked pursuant to the International Emergency Economic Powers Act (50 U.S.C. 1701 et seq.) (see OFAC's Specially Designated Nationals and Blocked Persons List at https://www.treasury.gov/resource-center/sanctions/SDN-List/Pages/default.aspx).

(d) Exception for trade agreements. The representation requirement of paragraph (c)(1) and the certification requirements of paragraphs (c)(2) and (c)(3) of this provision do not apply if-

(1) This solicitation includes a trade agreements notice or certification (e.g., 52.225-4, 52.225-6, 52.225-12, 52.225-24, or comparable agency provision); and

(2) The offeror has certified that all the offered products to be supplied are designated country end products or designated country construction material.

(End of provision)

CLAUSES

52.252-2 Clauses Incorporated by Reference.

As prescribed in 52.107(b), insert the following clause:

Clauses Incorporated by Reference (Feb 1998) This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es): https://www.acquisition.gov.

(End of clause)

Clauses incorporated by reference:

52.202-1 Definitions. (JUN 2020) 52.203-5 Covenant Against Contingent Fees. (May 2014) 52.203-6 Restrictions on Subcontractor Sales to the Government. (Jun 2020) 52.203-12 Limitation on Payments to Influence Certain Federal Transactions. (JUN 2020) 52.203-17 Contractor Employee Whistleblower Rights and Requirement to Inform Employees of Whistleblower Rights. (JUN 2020) 52.204-4 Printed or Copied Double-Sided on Postconsumer Fiber Content Paper. (MAY 2011) 52.204-13 System for Award Management Maintenance. (OCT 2018) 52.204-19 Incorporation by Reference of Representations and Certifications (Dec 2014) 52.212-4 Contract Terms and Conditions-Commercial Products and Commercial Services. (NOV 2021) 52.215-19 Notification of Ownership Changes. (OCT 1997) 52.232-1 Payments (APR 1984) 52.232-11 Extras. (APR 1984) 52.232-39 Unenforceability of Unauthorized Obligations. (JUN 2013) 52.232-40 Providing Accelerated Payments to Small Business Subcontractors. (DEC 2013) 52.242-13 Bankruptcy. (JUL 1995) 52.243-1 Changes-Fixed-Price (AUG 1987)

Clauses incorporated by full text:

52.212-5 Contract Terms and Conditions Required To Implement Statutes or Executive Orders—Commercial Products and Commercial Services. (May 2022)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (Nov 2021) (Section 1634 of Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (Nov 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Nov 2015).

(5) 52.233-3, Protest After Award (Aug 1996) ( 31 U.S.C. 3553).

(6) 52.233-4, Applicable Law for Breach of Contract Claim (Oct 2004) (Public Laws 108-77 and 108-78 ( 19 U.S.C. 3805 note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

__ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (Jun 2020), with Alternate I (Nov 2021) ( 41 U.S.C. 4704 and 10 U.S.C. 2402).

_X_ (2) 52.203-13, Contractor Code of Business Ethics and Conduct (Nov 2021) ( 41 U.S.C. 3509)).

__ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (Jun 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

__ (4) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (Jun 2020) (Pub. L. 109-282) ( 31 U.S.C. 6101 note).

__ (5) [Reserved].

__ (6) 52.204-14, Service Contract Reporting Requirements (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

__ (7) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

__ (8) 52.209-6, Protecting the Government’s Interest When Subcontracting with Contractors Debarred, Suspended, or Proposed for Debarment. (Nov 2021) ( 31 U.S.C. 6101 note).

__ (9) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (Oct 2018) ( 41 U.S.C. 2313).

__ (10) [Reserved].

__ (11) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (Sep 2021) (15 U.S.C. 657a).

__ (12) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (Sep 2021) (if the offeror elects to waive the preference, it shall so…