Technical_Specifications.pdf

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

See FAR 3.104

Technical Specifications

CLIN001 – 2019 Ford F-150 4x4 Crew Cab Pick-Up Truck (Brand Name or Equivalent)

These vehicles must match in color as closely as possible the standard color used by the Mexican Federal

Police for all official vehicles (“Metallic Cobalt Blue”) using auto paint offered by the manufacturer or after-market auto paint.

QUANTITY: 30 EA

Description

Motor V8

Displacement 5.0 L >

Horsepower 395 hp >

Torque 400 lb-ft >

Gear system Automatic

Speeds Electronic 10-Speed

Traction 4X4

Steering Power assist

Overall length 5,890 mm >

Overall width 2,029 mm >

Overall height 1,960 mm >

Payload 4,082 kg >

Interior Crew Cab

Passengers 5

Radio AM / FM stereo / Aux / 6 speakers

Misc Spare tire, jack, spray-in bedliner, black vinyl floor covering, manual air conditioning

Color White / Painted metallic cobalt blue (auto paint) after-market

A.1: Illustration for CLIN001

CLIN002 – Procure and Install Ancillary Equipment

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

QUANTITY: 30 EA

Description Min Quals

Cabling It must cover the loads required by the police equipment including harness and wiring with protection (Teflon Spaghetti) that does not generate interference or inductions.

Battery The vehicle must be equipped with two 12.0-volt batteries, isolated from each other, maintenance free, and with adequate amperage consistent with the normal operation of the vehicle, as well as with the additional equipment. The first battery should allow the normal operation of the vehicle, and the second one must supply energy to all the police equipment.

Electronic

Battery

Protector

This device must prevent the second battery from suffering a discharge of less than

10.5 volts and as a result, lose the warranty with the factory and the recharging capacity. It should allow the battery to be automatically recharged when the engine is turned on, without affecting its own nature.

Alternator It must have capacity enough to generate the load that the vehicle and the integrated police equipment require.

Flashing

Highlights

In the console of police controls, there must be an integrated control button to operate the high lights of the vehicle in an intermittent way.

Strobes Four Stroboscopic Lights System with six LED lamps, each one placed two of the front, and two on the rear headlights of the vehicle. The control of this system must be integrated in the control console of the police equipment and must comply with the following characteristics: - System of four lamps of six LEDs and an integrated flasher; each one with multiple flash patterns with the ability to work in a synchronized way between the four lamps, in crystal color. Three-year warranty on

LEDs and electronic components or maximum available in Mexico for this equipment.

Front and side warning lights installed on the bumpers

Four modules, with a minimum of three LED lights, each one in red color, and placed as follows: two on the sides and two at the front part of the bumper with the following characteristics per module:

Encapsulated lamp with a minimum of three IV generation LED lights in red color

Integrated electronic flasher that allows synchronized operation between them

Various flash patterns which have been previously programmed

Capacity for intermittent operation in a synchronized way

Compliant with the International Standard SAE J-595

Three-year warranty or maximum available in Mexico for this equipment for LED lights and electronic parts

Paint Metallic Cobalt Blue. This color is complemented with a white frame that starts in the trunk and goes up to end in the awning in order to give the impression of a dynamic and bold style. The paint must include anti-corrosive and high-density coating.

Bodywork Must be resistant to corrosion, made of aluminum or have anticorrosion coating.

Frame The vehicle must have a frame with anticorrosion coating on internal and external surfaces as well as anticorrosion coating for environments at sea level, for the hood, the awning, between the doors, and for any kind of splashes, and the minimum warranty must be three years or maximum available in Mexico for this equipment.

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

Description

Coating Anti-slip and anticorrosive in floor and trunk.

Brush

Guard

(Bumper)

Must withstand 3,000 kg. pressure without deformation or damage to the vehicle and have the following characteristics:

Fabricated from 1/4 – inch ASTM-36-A sheet steel with two cross tubes of 1 ½-inch 16-caliber steel tubing and a central brace of 1/8-inch sheet steel. Steel anchors with a plate thickness of ¼ - inch attached to the chassis. Protective high-density polypropylene molding attached to the front section. Solid ½ - inch rings welded to the lower cross tube. Covered with high-impact, black polyester-powdered electrostatic paint that resists impact and UV rays.

Vehicle

Towing

Rings

The vehicle must have 2 front rings and two at the rear to pull vehicles up to 3000

Kg. The rings must have a minimum inner space of 5 cm. The rear rings must be manufactured with a ¼- inch thick steel plate, and have a 1/2-inch solid, round material hoop. The finish should be semi-gloss black.

Drag Pull of the Vehicle

The minimum dragging capacity should be 2500 pounds.

Control

Console

The vehicle must be equipped with a console to install the control panels of the turret, radio and other services; it must be manufactured of 16 gauge steel sheet, and the finish should be in matte black corrugated paint.

Tool

Cabinet

The vehicle must be equipped with a cabinet aimed to store and transport tools and other accessories. It must be made of antioxidant and anti-slip sheet, and installed din the bed of the truck, right next to the rear medallion. The dimensions must be in accordance to the model of the proposed truck. The vehicle must be equipped with a tool cabinet box that: 1) fits exactly in height reaching the truck bed floor 62.31(L) x 23.135 (H) x 15.75 (W); 2) contains an additional protected box for second battery to avoid losing warranty for drilling or cutting the box; 3) is mounted by the same supplier of the ancillary equipment in order to maintain the warranty.

Turret

Mounted

Traffic

Light Bar

The vehicle must have a light bar with patterns of pre-programmed flashing with automatic change according to the function it performs. It must also have programming capability according to the needs of the corporation, with the characteristics described as follows, It must be latest generation 306 super LED lights with the following configuration:

Four reflective modules with flexible electronic card to eliminate blind spots between the corner module and the front and/or rear directional lamps. Each module must have a super LED 36, IV generation base and should be located as follows: two red lights at the front, and two blue ones in the back; they must be placed diagonally in the corners and have an operating capacity in cruise light mode.

Six reflector modules with duo-color technology consisting of 12 super LED IV

Generation lights each, in amber color for traffic bar functions, and six in blue color for flashing functions with operation capability in cruise light mode.

Front approach light with two modules of six super LED fourth generation "HID" crystal color lights, which should be placed in the center of the front of the light bar and two modules of three super LED "HID" crystal color lights, placed in each end of the front of the light bar, which must operate in both: a fixed and intermittent manner.

Alley lights on the sides of the bar with two modules of 12 Super Led, IV generation lights in crystal color, which must operate in a fixed and intermittent way.

Extruded aluminum base and cover.

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

Description

Turret

Mounted

Traffic

Light Bar

Polycarbonate domes injected in crystal color (transparent and uniform) with protection against UV rays to prevent discoloration (hard coat). They must be aerodynamic, of high impact resistance, interchangeable and protected with a seal to prevent the passage of water, dust or soot.

Mounting brackets made of adjustable Zytel nylon with a mechanism that allows the correct leveling of the turret, regardless of the slope of the awning.

The vehicle must comply with Standards SAE J-845 and SAE J-595 for light bars on emergency vehicles.

Electronic

Siren 100/200 watts of power electronic siren with controller of lights type "hand held".

Official tones: wail, yelp, phaser and /or HI-LO, out of a total of 37 tones.

Air horn type (duck).

Interface for retransmission of radio transreceptor.

Hands-free operation system from the steering wheel of the vehicle

Automatic volume control.

Compact control panel to be operated with one hand, (animating) with a unidirectional microphone for paging.

Comprehensive operation of the functions of the visual and acoustic signaling system through three master switches and nine secondary ones.

Board lighting with parking lights for night operation.

Must be compliant with Standard SAE J-1849.

Must have two 100w output power speakers.

They must be of the same impedance and suitable for the output of the central control module of the siren

They must have a compact design so that they can be installed in any kind of vehicle.

They must have a nylon base for its support, which must be resistant to weathering, vibration and corrosion.

The speakers must have a sensitivity of 123 db.

They must be placed in the front of the vehicle, without being visible.

They must be installed in a location that avoids sound distortion and must not interfere with the vehicle's operation.

They must be compliant with Standard SAE J-1849, Class 1 for sirens and speakers of emergency vehicles. This standard must be equivalent to that of the country of origin.

Functions of the visual and acoustic signaling system

Switch master 1 (patrolling) - Activation in intermittent and alternating mode of the 4 corner lamps in red and blue.

Switch master 2 (assistance) – Adds intermittent and alternating mode to the 4 front lamps in red and the blue LEDs of the rear duo lamps are added.

Switch master 3 (emergency) - to the previous functions, the intermittence of the traffic bar, the alley lights and the approach light is added.

HF switch (hands-free siren operation) - When this function is activated, the siren tones are operated from the original horn (steering wheel) of the vehicle using the following sequence of tones:

First touch - activates the WAIL tone.

Second touch - activates the YELP tone.

Third touch - Activate the PIERCER tone.

Fourth touch - the tone sequence ends.

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

Description

Functions of the visual and acoustic signaling system

MAN Switch - Momentarily activates the police presence tone.

HORN switch - activates the HORN tone.

WAIL switch - activates the WAIL tone.

Switch RAD - activates the retransmission of the transceiver radio through the siren speakers.

Switch ALLEY - activates the street lamps according to the following sequence:

First touch: activates the street lamp on the right side in a fixed manner.

Second touch: activates the alley lamp on the left side in a fixed manner.

Third touch: activates both street lamps in a fixed way.

Fourth touch: the lighting sequence of the street lamps ends.

Switch TAKE DOWN - activates the approach lamp in a fixed manner.

Switch RIGHT - activates the sweep with left-right direction of the traffic bar.

Switch LEFT - activates the sweep with right-left direction of the traffic bar.

Switch RIGHT + LEFT - activates the sweep with direction center - ends of the traffic bar.

Functions in additional control board

Switch 1- activates the cruise light function (CRUISE LIGHT)

Top position - It activates in a fixed and tenuous way the 4 corner lamps (red and blue), 4 directional lamps in red color and the 6 rear lamps (3 in blue and 3 in amber). Lower position - activates the high and low intensity of the following turret lamps: 4 corners, 4 front and the 6-rear lamps type duo.

Switch 2 - activates the convoy function.

Top position - activates the convoy tip function with the 4 front lamps of the turret in an intermittent way. Lower position - activates the convoy queue function, of the blue color of the 6 rear duo lamps intermittently.

Switch 3 - Top position - activates the aerial sighting function, which allows to interact with the air units according to the rhythm and flashing pattern. Lower position-activates the police command function, which allows to identify according to the rhythm and flashing pattern that is the arrival of a police officer.

Switch 4 - activation of the 4 red lamps located in the brush guard of the unit in an intermittent and synchronized way.

Switch 5 - activation of the lamps in glass color in intermittent mode that must be located in front and rear headlights of the unit.

Switch 6 - activates the intermittent Wig Wag function of the high beams of the headlights and rear headlights.

CLIN003 – Install INL Supplied Radios

Install INL

Supplied

Radios

The contractor shall install INL-furnished UHF radios, with the following specifications:

Motorola APX2500

M24URS9PW1 N APX2500 7/800

QA02505 ADD: APX 2500 EXPANDED SW PACKAGE

QA01648 ADD: ADVANCED SYSTEM KEY - HARDWARE

GA00804 ADD: APX O2 CONTROL HEAD (Green)

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

G444 ADD: APX CONTROL HEAD SOFTWARE

G66 ADD: DASH MOUNT

W484 ALT: ANT 3DB GAIN 762-870MHZ

W20 ADD: KEYPAD MIC GCAI

G142 ADD: NO SPEAKER NEEDED

GA00270 ADD: GPS ANTENNA GLASS MT

G843 ADD: AES ENCRYPTION APX

The contractor shall ensure that radio is adequately shielded to prevent RF interference from the vehicle’s electrical system while the vehicle is in operation.

A.2: Photo of Federal Police vehicle with standard markings and equipment as required in

CLIN002 and CLIN003

CLIN004 – Procure and Emplace Decals

Type of material Vinyl self-adhesive reflective graffiti engineering grade.

Printing Images in high resolution at 1200 DPIS and institutional logos cut by computer

Specifications Vendor shall be responsible for the indicated design, proper printing and proper installation of the official institutional custom graphics, decals and lettering for 30 pick-up trucks 4x4. Vendor shall provide a decal kit for each type of vehicle that must be inspected and approved by INL before final production. Service shall be delivered upon approval and coordination with INL

Logistics Mexico.

Procurement Sensitive: Unauthorized disclosure of this information violates the Procurement Integrity Act.

1 (One) microperforated windshield POLICÍA FEDERAL

3 (Three) ESTRELLAS MEXICO (1 hood, 1 right side, 1 left side)

4 (Four) SSPC logos (1 awning, 1 right side, 1 left side, 1 rear side)

1 (One) 088 logo (1 rear side)

3 (Three) POLICIA logos (1 right side, 1 left side, 1 rear side)

3 (Three) FEDERAL logos (1 right side, 1 left side, 1 rear side)

1 (One) PROTEGER Y SERVIR A LA COMUNIDAD logo (1 rear side)

A.3: Illustration of standard Federal Police vehicle markings for reference in CLIN004