SS_N0039_Colombia_Security_Equipment.pdf

RESPONSE TO SOURCES SOUGHT NOTICE (191NLE19N0039)

Department of State

Bureau of International Narcotics and Law Enforcement Affairs (INL)

Colombia Prison Reform Security Equipment Bogota Colombia

I. SOURCES SOUGHT SUBMISSION NOTICE

This Sources Sought will be used to identify potential sources that are interested in and capable of performing the work described in this “Draft” Statement of Work (SOW). In accordance with FAR 15.201(e), responses to this notice are not offers and cannot be accepted by the Government to form a binding contract. This Sources Sought is issued solely for conducting market research, information and planning purposes and does not constitute a solicitation or obligation on the part of the Government. Neither unsolicited proposals nor any other kind of offers will be considered in response to this Sources Sought. No reimbursement will be made for any costs associated with providing information in response to this announcement and/or any follow-up information requests.

The purpose of this Sources Sought is to communicate and solicit feedback from industry on the “Draft” version of an upcoming overseas requirement for Colombia Prison Reform Security Equipment. Contractors shall provide company capabilities and pictures. The NAICS Code for this requirement is 453998 All Other Miscellaneous Store Retailers.

Please do not provide generic capability statements, as they shall add no value to this Sources Sought. The Government is seeking specific information in conjunction with the specifications of this requirement.

The page limitation for responses is 10 pages.

All responses shall be submitted in writing via email to Dennis M. Fuentes (Senior Contract Specialist) at fuentesdm@state.gov, no later than 11:00 AM, EST on Wednesday, July 3, 2019.

In order to participate in the resulting RFQ and to be eligible for an award, the proposer must have (i) a current CAGE Code, (ii) a DUNS#, (iii) be registered to do business with the Government of the United States in the System For Award Management (SAM) and not be on the Excluded Parties List: https://www.sam.gov

II. COMPANY INFORMATION

Company Name Address DUNS Number Company Website POC Name Phone Email mailto:fuentesdm@state.gov https://www.sam.gov/

III. SOCIOEONOMIC STATUS

a. Provide information pertaining to your company’s socio-economic status for federal procurement programs (small, HUBZone, 8(a), Women-owned, veteran-owned, etc.)

under NAICS code 453998.

The size standard for NAICS 453998 is $7.5M dollars. Unless the SBA has granted a class waiver of the NMR for a particular product, the company will either be required to be the manufacturer of the products offered or qualify for the procurement as a “nonmanufacturer”. In accordance with FAR 19.102(f), the applicable size standard for a “nonmanufacturer” is 500 employees.

Response:

b. Is your company the manufacturer of all the products included in Attachment 1?

c. If your company is not the manufacturer, identify the manufacturers’ names, addresses, DUNS numbers, and other pertinent information. Are all manufacturers U.S. small business concerns?

d. If the manufacturer is not a US small business concern, has the SBA issued a class waiver of the non-manufacturer rule for the product? If so, please identify the applicable class waiver(s).

IV. PRODUCTS AND SERVICES

a. Provide a list of the products sold by your company meeting the requirements of this

Sources Sought. Where a particular standard is included in the Sources Sought, address your company’s product compliance with said requirements. Please note that unless explicitly stated all products in Attachment 1 will be solicited on a brand name or equal basis.

b. Is your company an authorized seller of the above-mentioned products in Colombia? If so, what business licenses does your company possess in Colombia?

c. What areas of Colombia does your company service? Briefly describe your current logistical capabilities in Colombia.

d. Provide a brief description of your corporate experience in Colombia and Latin America.

e. Are the products sold by your company covered under warranty in Colombia? If so, what is the length of the warranty offered? Are repairs handled in country?

f. Does your company provide training in Spanish? If so, is training accomplished via Spanish speakers or via the use of translators?

g. Are equipment manuals provided in Spanish?

h. Would your company need to subcontract any part of the work? Please explain.

V. EXISTING CONTRACTS

a. List any existing contract vehicles through which the US Department of State can access your company’s products and services (i.e. GSA FSS, IDIQs, etc.)

VI. RECOMMENDATION

a. Did your company identify any areas in the draft specifications that present excessive risks or other concerns? If so, please provide detailed information and suggested mitigation.

EMBASSY OF THE UNITED STATES OF AMERICA

U.S. Department of State Bureau of International Narcotics and Law Enforcement Affairs (INL)

Bogotá, Colombia

STATEMENT OF WORK (SOW)

DATE: February 07, 2019

PR NUMBER: PR8050896

DESCRIPTION: SECURITY EQUIPMENT

PROGRAM: INL Corrections Reform Program

1. BACKGROUND

This project is being sponsored under the Paz Colombia Initiative, the U.S. Department of State (DOS), as well as other agencies is supporting the professionalization of the Colombian Prison System at the National and municipal levels. The Bureau for international Narcotics and law enforcement Affairs (INL), through the Narcotics Affairs Section of the US Embassy in Colombia has been designated the lead agency within the DOS to implement the Paz Colombia programs. The Government of the United States and the Government of Colombia (GOC) have agreed to support the GOC to achieve prison reform and improve Colombia’s prison system so that it operates in a safe, secure, humane and transparent fashion. INL will assist the investigation and prosecution of major crimes such as human rights violations, drug trafficking, homicide, kidnapping, and money laundering; foster a culture of lawfulness; strengthen justice sector reform and improve Colombia’s prison system with the objective of assisting the GOC in significantly reducing the levels of violence, corruption and compliance with International Standards in the local, state and National correctional facilities.

2. PROJECT JUSTIFICATION

The U.S. Department of State is supporting the Corrections Reform Program, an on-going, long-term agreement between the US and Colombian Governments to achieve prison reform and improve Colombia’s prison system so that it operates in a safe, secure, humane and transparent fashion. Part of the Corrections Reform Program is to support the GOC by providing mentoring, advice, some equipment and training for select prison officials and administrators. Goal is to achieve international norms, best practices through compliance with International standards.

Purpose of this statement of work is, the GOC is requesting support to achieve prison reform and improve Colombia’s prison system so that it operates in a safe, secure, humane and transparent fashion.

The Department of State, International Narcotics and the Application of the Law of the USA. UU Request a quote to purchase the following equipment for the Central Prison of Jamundi, the Central Spinal Prison and the National Penitentiary Training Academy of Bogotá, Colombia, to help them comply with international standards for ACA corrections, as well as availability of security systems, life safety and protection of officials.

2. DELIVERABLES

ANTI RIOT GEAR/ ANTI-RIOT SUIT

ITEM COUNT

ANTI RIOT GEAR/

ANTI-RIOT SUIT

TECHNICAL SPECIFICATIONS ANTI RIOT GEAR/ ANTI-RIOT SUIT

Characteristics

Must comply with the technical standard NTMD-0262-A1.

The anti-riot suit provides superior protection against impacts with blunt objects in the most vulnerable areas.

With pre-baked external materials highly resistant to mechanical and environmental conditions, inside materials that promote cushioning and protection of the body.

It is resistant to forceful blows, short-pointed elements, chemical substances and fire-retardant, risks to which the user is confronted during the handling of crowds and riots.

All this comes together in a quality suit, with the latest technology, flexibility and comfort for the most demanding users.

• Hard frontal panels on the front and back with flexible 3-panel design for optimal movement, fit and comfort.

• Electrum XK8 ™ 3 mm front and rear panel.

• Protium ™ impact absorbing foam with mesh.

• Electrum XK8 ™ plate with Protium ™ foam that covers the upper part of the shoulder and arm.

Forearm protector:

• Electrum XK8 ™ two-piece hard outer layer for the necessary flexibility for the forearm and elbow.

• Protium ™ impact absorbing foam, covered with Cordura nylon.

• Polyester mesh covers the interior to be comfortable and breathable.

Thigh protector and inglé: Electrum XK8 ™ external hard layer on thighs and hips.

• Protium ™ impact absorption foam with 150 denier Cordura® nylon cover and polyester mesh inside.

• Electrum XK8 ™ inner groin section with Protium ™ foam padding and mesh cover.

Knee and shin guards: Knee guards with hard Electrum XK8 ™.

• Electrum XK8 ™ tile plates with matt black finish.

• Resilient Protium ™ foam padding.

• Adjustable and removable foot protectors.

• Each piece of the suit is quickly secured and adjusted with nylon straps, Velcro® and quick-connect clips, allowing for a customized fit.

Available sizes: MD to 3XL.

Bag of equipment: Dimensions: 24 "x19" x15 "(60.9 x48.2 x38.1cm).

• Interior dimensions: 24 "x15" x15 "(60.9 x 38.1 x 38.1cm).

• Two storage compartments in the front of the bag.

• Removable padded shoulder strap.

BULLETPROOF VESTS

BULLETPROOF

VESTS 75

TECHNICAL SPECIFICATIONS BULLETPROOF VESTS

Protective, comfortable and discreet garment that absorbs the impact of the projectile, which provides protection at least in the back and sides, adjustable on shoulders; by means of suspension or velcros.

The outer fabric of the vest can be black polyamide or polyester.

The color of the threads, adhesive closures and accessories, should be tone to tone with the color of the outer fabric of the vest.

- Ministry of defense technical standard NTMD-0028-A 28 "bulletproof vest", current update.

- U.S. department of justice, office of justice programs. National institute of justice. ballistic resistance of body armor NIJ standard-0101.06, July 2008

Protection Level III A

The vest must be made with non-rigid level IIIA armor material, allowing ease of movement of the official and his comfort; in the visual inspection should not be evidence of cuts, tears, holes or abrasion marks.

The bulletproof vest must fit firmly to the user's anatomy. Must provide protection at least on back, chest belly and sides; the opening of the armhole must be proportional to the size, providing the greatest protection. Likewise, it must have the possibility of adapting the vest optionally, protective pelvis, arms and / or neck removable.

- The ballistic panels offered must comply with the technical norm NIJ standard-0101.06 for which the manufacturers, the material of the ballistic panels must NOT be recycled, remanufactured and must NOT have more than six months of storage, for which the supplier must present the corresponding record of the fiber manufacturer. The supplier must present a declaration of conformity about the date of preparation of the ballistic panels, where it ensures compliance with technical norm NIJ 0101.06.

- It is important that the armor material used in the ballistic panels be light, 100% flexible, that offers ergonomics, comfort and body fit, always maintaining the composition of the NIJ standard.

- The trauma reduction plate must be made in accordance with what is stated in the NTMD-0225 current update, according to the level of shield protection required for the vest.

100% aramid in new materials, latest technology, so it can not be re-manufactured, or stored.

Documentation of certificates presented by the manufacturer must be attached, where they indicate the conditions of the element.

They will be made in RISTOP LIVIANO or FLAT FABRIC, waterproof sealed with ultra sound / high frequency or heat sealed, with antibacterial properties. Seams are not allowed, in the same way a certificate issued by the accredited laboratory or manufacturer of the material must be attached, indicating the properties of the requested material.

Located in the outer panels lining, in SPANISH language, with indelible ink, it must have waterproof protection, which will allow to keep the information legible during the life of the vest, where it is announced as a minimum: serial, date of manufacture, batch number, country of origin, size, material of the shield, date of expiration of the panel, legend "body side" technical norm, among others.

The offeror must guarantee the availability of the different sizes: S, M, L, XL.

SIZE QUANTITY

S 10 M 10 L 50

XL 30

Flat fabric in polyester and cotton composition, with anti-bacterial and anti-stain treatment;

must be accredited by the manufacturer of the material, indicating the properties requested.

It will have a maximum weight of 2,000 grams comprising level IIIA panels in its external lining and without anti-trauma plate. Based on size L.

Its composition must be 100% polyester, to ensure the maintenance of body temperature according to the environment (weather), which should allow for breathability and comfort, antibacterial absorption treatment and rapid drying. A certificate issued by an accredited laboratory or manufacturer of the material must be attached, indicating the properties of the requested material.

Of removable type, located in the front part of the external lining of the vest, in which the information to be contained will be coordinated with the entity.

- It should be lodged in the outer lining at the level of the sternum.

- Made of the same ballistic panel material, it will be flexible, and will be sealed by ultrasound or thermostatic seal.

Its size will be standard that will protect the area of the sternum.

It will be made of waterproof material, anti-tear, washable, that fits the dimensions of the vest.

It should include a bag per vest, for the conservation of it.

Guarantee Balistic Panel (05) years counted from the date of delivery of the vest to the INPEC.

External Lining Guarantee (02) years counted from the date of delivery of the vest to the INPEC.

FIVE STAR GEAR DUTY RIG IN A BOX / OFFICER DUTY BELTS WITH KEEPERS

AND KEY HOLDERS

FIVE STAR GEAR

DUTY RIG IN A

BOX / OFFICER

DUTY BELTS

WITH KEEPERS

AND KEY

HOLDERS

TECHNICAL SPECIFICATIONS FIVE STAR GEAR DUTY RIG IN A BOX / OFFICER

DUTY BELTS WITH KEEPERS AND KEY HOLDERS

• TACTICAL BELT

Multipurpose Belt must be a set of two belts, External and Internal, which must be coupled by a hook and loop tape.

External Belt: It must be composed of a plastic sheet core, loop, hook and loop tape, faya tape, sheet metal and pins.

The inner material of the belt must be a plastic sheet; it must be covered by the external face with a loop, which in each of its ends must carry a portion of tape on the side of the hook. On the inner side, you must wear a contact tape on the side of the hook, which must have the same length as the plastic sheet. At its ends and over the straps, on its internal side, portions of ribbon tape must be placed.

The plastic sheet, the loop and the contact tapes must be joined together with a central stitching seam that must go along the belt. The contour of the belt should be edged with a faya tape, fixed by a stitching seam and that should secure the three components: rope, plastic sheet and the hook and loop tapes.

The ends of the belt must have a rounded, ties or closures of the faya tape should be made on the side.

The coupling of the three components: rope, plastic sheet and the hook and loop tapes, once integrated, must pass properly through the space in the sheet that allows the adjustment between these elements.

The tips of the tape in their ties or closures should be topped with heat, to avoid detachment of the fibers that compose it.

Closing plate. The closure of the outer belt must have a plastic closure plate (female-male).

The closing plate must have three security points located like this: a double lock on the sheet metal edges on the male part and a lock on the central part of the male part. The three insurances must be perfectly coupled and open only when operating the total insurance simultaneously.

Internal Belt: It must be composed of rope, hook and loop tape and a plastic buckle.

The inner belt must be made up of a loop as the main component, on which, on its outer side, a contact tape must be adhered and superimposed on the loop side, at the end of the outer face, a portion of the hook tape must go .

The loop tape portion of the outer face must go from the seam of the flap that houses the buckle, to where the tape portion starts from the hook side.

The inner belt, on its inner side, must have a portion of ribbon loop over it at the end.

The loop and the hook and loop contact straps must be joined together with a straight stitching center seam that must go along the belt. The contour of the belt, must be edged with a faya tape fixed by a stitching seam that must secure the components: loop, and hook and loop tapes.

One end of the belt must have a fold that forms a flap which must accommodate a bridge buckle. The cap should close towards the inner side of the belt and should be sewn with a double seam closure.

The opposite end of the belt must have an angular cut. The ties or closures of the faya tape should be made at the end where the right angle of the belt is formed.

TONFA HOLDER

Element used to insert the cane (tonfa type) and thus carry it in the belt (reata) of the uniform.

REQUIREMENTS

Body: The body of the tonfa-holder must accommodate a tonfa stick that complies with the NTMD 0263 standard (last update), fitting perfectly to the heart of it.

In its rear part it must have a coupling that allows its assembly with the hook to fasten the belt.

On the sides, the upper part must have a piece of cylindrical shape that allows the assembly of the tonfa cane and its fittings.

The body must be functional for both right-handed and left-handed people.

The tonfa-holder should be homogeneous through the wall that makes contact with the heart of the tonfa-type stick and uniform in color, opacity and density.

Belt fastening hook: Rectangular shaped, made in one piece, with opening in the lower part of the front face, on the same side it must have a semicircular eyelet with its external edge in high relief, the back of the hook must have an eyelet of circular shape that must match the one located on the front.

The hook must have a hole in the lower part to place a screw with its respective hexagonal nut for fastening to the belt.

The hook must have a system that allows the fastening and dismantling of the body of the tonfa -holder, giving it a rotation of not less than 90 degrees on either side of its resting position, without allowing its exit in use.

Safe tonfa type: Located in the upper part of the body of the tonfa-holder, made in one piece, its design should allow the release with the thumb of the user while it grabs the tonfa-type cane by holding it completely, it must be removable, to be located according to the need of the user (right or left) by means of a screw with nut and spring in the internal part that allows its movement to release or secure the cane.

• HANDCUFFS HOLDER

Element used to lodge the handcuffs easily and safely, made of a material with high resistance to impact and friction, to carry them in the belt (reata) of the uniform.

Body. Rounded in shape, on its back side has a rail type channels or other system that allows the assembly of the hook that will attach it to the belt and in this same place is attached the flexible insurance system whose function will be to hold the handcuffs so they do not go out of the body, on its front face will go the hook type adjustment system that will be coupled with the other end of the flexible safety so that the handcuffs do not come off unless this system is activated by the user. The handcuffs should house a set of handcuffs without any mobility.

Secure: Must be flexible to allow greater maneuverability in terms of opening and closing the handcuffs holder, in its middle part it has a rectangular hole (where the chain of handcuffs will go), one of its ends must allow the same subjection to the body of the handcuff holder (back) through three holes or another similar system that guarantees a perfect assembly, this part must be reinforced to avoid its rupture with the manipulation. At the other end located on the front of the body must carry a piece with non-slip finish that facilitates the handling of the insurance (opening and closing) by the user.

Fastening hook to the belt: In its front view, it must have rail channels or any other system that allows it to be attached to the body of the handcuffs holder, in its rear view it has a hook-like part with a nail on the lower part - internal, to be fastened to the belt by means of a system of lateral pressure that makes that once lodged there, it does not move from its place.

• PROVIDER HOLDER

Body: Consisting of two compartments (for two suppliers for gun). On its back face must carry a rail type channels or other system that allows the assembly of the hook that will attach it to the belt and in this same place is coupled the system of insurance provider holder whose function will be to support the suppliers of the gun so that Get out of the body

Provider holder insurance: It must be elongated and have some elasticity to allow suppliers to enter or extract more quickly, consisting of an upper part by two elongated supports finished with concave nails to hold the base of the suppliers perfectly and a lower part with a support that will go to the adjustment system to the body of the provider holder.

Belt attachment hook: In its front view it must have a rail type channels or any other system that allows coupling to the body of the provider holder, in its rear view it has a hook-like part with a nail in the lower part - internal to be fastened to the belt by means of a system of lateral pressure that makes that once lodged there, it does not move from its place.

• GLOVES HOLDER

Body: Consisting of two compartments for two disposable gloves (in latex or similar material) in the form of a box without holes for better storage of them. On its rear face, it must have rail-type channels or another system that allows the hook to be attached to the belt. On the upper part sides, the body must have pins to assemble the safety or lid of the glove holder. The back - top edge should have a system for opening and closing the lid.

Safe (lid) glove-holder: On its sides should carry two pieces in high relief, which assemble perfectly with the pins located in the body of the carrier-provider, allowing it to give mobility to it, likewise must have a piece compatible with the system of closing and opening. The insurance or cover must completely cover the upper part of the body.

Fastening hook to the belt. In its front view, it must have rail-type channels or any other system that allows it to be attached to the body of the glove-holder, in its rear view it has a hook-like part with a nail on the lower part - internal to be fastened to the belt by means of a lateral pressure system that makes that once lodged there, does not move from its place.

• LANTERN HOLDER

Body: Round in the front and square on its sides and back, without lids on the top and bottom, on the back must have channels like rail or other system that allows the assembly of the hook that will attach to the belt, on the sides, it must have two pieces in a rectangular shape that communicate with the interior of the body, where the torch locks will be housed for adjustment and expulsion.

Lantern holder: Overlapping pieces that must be assembled perfectly in the body of the lantern holder by means of pins to achieve a safety system of the lantern, preventing it from leaving unless the user activates the release buttons easily and safely.

Belt fastening hook: In its front view must carry a rail type channels or any other system that allows to attach to the body of the lantern holder, in its rear view has a hook-like part with a claw on the bottom - internal to be fastened to the belt by means of a system of lateral pressure that makes that once lodged there, it does not move of its site.

NOTE: ALL ACCESSORIES MUST BE ASSEMBLED PERFECTLY IN THE BLACK

MULTIPURPOSE BELT (ACCORDING TO ET-PN 070 A7) AND BELT IN BLACK 55

MM STRAP (ACCORDING TO NTMD 037 LAST UPDATE).

GAS MASK

GAS MASK 120

2.1 TECHNICAL SPECIFICATIONS GAS MASK

ANTIGAS MASK. MODEL ADV1000. MARK MSA POLICE LINE

Flexible one-piece mask, polyurethane lens with wide field of vision, joined by a durable rubber. 40% lighter than other masks, adjustable 6-point nylon harness that allows you to easily put on and take off without pulling your hair. Molded nose cup minimizes fogging. Police personnel and military personnel are protected from a variety of respiratory risks, with this complete line of CBRN and anti-riot gas masks.

With flexible lenses, you will have a wider field of vision; In addition to being manufactured permeable and resistant in the speech diaphragms, this mask protects, with a comfortable fit and superior visibility. Available in a variety of styles and configurations.

Sizes: Small, Medium and Large.

Provides respiratory protection against military war, civil unrest and NRBC threats.

High performance with comfortable fit in a variety of military and riot masks.

Attracts, recovers and neutralizes contaminants.

Flexible lens with a wider field of view for superior visibility.

Can be put on and off easily.

HAND HELD METAL DETECTOR

HAND HELD

METAL

DETECTOR

TECHNICAL SPECIFICATIONS HAND HELD METAL DETECTOR

Greater sensitivity: detects a medium-sized pistol from 9 inches away; a large knife from 6 inches; razor blades and blades from 3 inches apart; drugs wrapped in aluminum foil and small jewelry from 1 inch Autocalibration: digital microprocessor technology eliminates the need for periodic sensitivity adjustments.

High impact ABS housing with reinforced coil compartment. Exceeds Mil-Std -810F (drop test) 516.5, procedures II and IV.

Large 8-inch scanning surface for fast and thorough scanning.

No tools are required to change the standard 9V battery (included). Optional rechargeable battery kit available.

Strong audible alarm and bright red LED indicate metal detection.

Momentary pressure button helps to temporarily eliminate the detection of environmental metal in the immediate vicinity such as steel bars, metal walls.

LED indication of three colors: the green LED indicates ON; the amber LED indicates low battery: the red LED indicates ALARM.

Operating temperatures: -35 ° C (-37 ° F) to 70 ° C (158 ° F)

IMPACT RESISTANT POLICE SHIELD AS-60 ASR-60

IMPACT

RESISTANT

POLICE SHIELD

AS-60 ASR-60

TECHNICAL SPECIFICATIONS IMPACT RESISTANT POLICE SHIELD AS-60 ASR-60

No. DATO TÉCNICO REQUERIMIENTO 1 COLOR LAMINA Transparent colorless 2 MATERIAL Polycarbonate or high impact polyethylene

2.1 LENGTH Molded polycarbonate sheet.

2.2 HANDLE

Aluminum attach isoi sae certification of the type of alloy that make up the grip, or in its absence certification of the manufacturer of the aluminum that makes up the handle. the handle must be made of solid and not hollow tube.

2.3 ARM SUPPORT Reata 100% nylon.

2.4 PAD Rubber Eva

2.5 BROOCHES chromed brass

3 DIMENSIONS

3.1 BODY

3.1.1 LONG 820+/-5mm

3.1.2 WIDTH 550 +/- 5mm, taken on the outside of the shield in a curved shape with a flexometer.

3.1.3 THICKNESS 4.5 +/- 0.5 mm

3.2 HANDLE

3.2.1 DIAMETER AND LONG 241+/-2mm.

3.2.2 HANDLE DIAMETER 22+/-2mm.

3.2.3 HAND GRIP

3.2.3.2 NUTS (4) Galvanized iron with protection ribs. (4) nuts.

4 TOTAL WEIGHT Maximum 4000 grams.

5 DESIGN AND FINISH

5.1 CONCAVITY IN PARALLEL

MEASURED FROM THE 100+/-5mm.

No. DATO TÉCNICO REQUERIMIENTO

INTERNAL PART OF THE

SHIELD TO A

HORIZONTAL PLANE

5.2 SIGN "INPEC" Screen-printed adhesive material.

5.2.1 COLOR Black background, white letters.

5.2.2 LETTER DIMENSIONS

5.2.2.1 HIGH 110mm+/-5mm.

5.2.2.2 THICKNESS 25mm+/-2mm.

PR-24 BATON

PR-24 BATON 280

TECHNICAL SPECIFICATIONS PR-24 BATON

GENERAL REQUIREMENTS

Design and finishing. The tonfa cane must be made in one piece and in the same material. All its finishes must be curved, free of corners, burrs, cracks, sharp edges, stains, cracks, twists and defects of the manufacturing process such as bubbles. The parts that are free of Anti-slip should be smooth and smooth and their ends rounded.

Material. The tonfa cane must be made of polymer.

Color. Black color in semi-matt finish.

The color and the finish must be uniform throughout.

Parties. For verification purposes of the tonfa cane, it is divided into four parts: body, main handle, lateral handle and heart, according to the indicated in figure 1.

Body. Indicated in figure 2. It must be of cylindrical shape with a flat finish in a triangular shape as indicated in figure 1 and with a curved end at its end. The flat finish must be clearly defined in the length it occupies.

The diameter of the front face of the body of the shaft must decrease proportionally, in such a way that the difference in diameter of the end of the element with the diameter of the connection with the heart is 2 mm ± 0.2 mm.

Main handle. Indicated in figure 3. It must be cylindrical, it must have an anti-slip finish formed by 10 channels located along the cylindrical piece and 08 channels located around the same piece.

At its end it must have a round head with curved ends.

The anti-slip finish must be located centrally, in relation to the end that joins the heart and the beginning of the head.

Both the channels and the frames that are formed by the effect of the crossing of the same, must be uniform and symmetrical.

Lateral handle. Indicated in figure 4. It must be cylindrical, it must have an anti-slip finish formed by 10 channels located around the cylindrical piece, at its end it must have a round head with curved ends and the union with the heart should be curved shape.

The channels that form the anti-slip finish should be uniform and symmetrical.

The anti-slip finish must be located centrally, in relation to the end that joins the heart and the head in its maximum diameter.

The diameter of the part that joins the heart should be maintained in an extension of 56 mm ± 2 mm, from that location the diameter should be proportionally decreased until it is joined to the head.

Heart. Indicated in figure 5.

For purposes of determining the design of the heart, it will be divided into the following parts:

upper part, lower part, side parts, front face and rear face, the top part will be the one that joins the main handle and the front part. that joins with the side handle.

The back face must have a surface with a granular finish, which will include the entire area of the face, up to 4 mm ± 0.5 mm from the edge of the heart, symmetrically in all its contour.

The width of the heart, starting at a distance of 60 mm ± 2 mm from the joint with the main handle, should decrease 29.5 mm ± 1 mm, until the union with the body.

The front face must have the lateral handle implanted.

The thickness of the heart in the anterior part should decrease proportionally 2 mm ±

0.2 mm, starting from the union with the body until the union with the lateral handle.

This thickness should be kept in the area around the side handle and should be increased proportionally until the main handle is born.

The heart must have two spaces established for the labeling of the element, which must be located in the lateral parts of the same at the height of the lateral handle. For identification purposes of each of the areas, area No. 1 will correspond to that located on the right side (of the element) and area No. 2 to that located on the left side (of the element), taking the cane on the back, with the body facing down.

Dimensions. it must have a total length of 600 mm ± 5 mm, in accordance with that indicated in figure 1 (dimension A) and must comply with the dimensions indicated in tables 1 to 4.

Table 1. Body Dimensions

Description Cota Dimensions in mm

Tolerance in mm

Total length B 360 3 Flat finished length C 330 3 Extreme diameter D 31 1

Diameter union heart E 31 1 Anterior face diameter at the junction with the heart F 29 1

Curved finished end radius G 15 0,5 Flat finished width at the junction with the heart H 16 1

Table 2. Dimensions Main Handle

Tolerance in mm

Total length I 133 2 Antislip finished length J 108 2

Diameter K 31 1 Diameter head L 36 1

Head radius M 42 1

Thickness head N 10 1 Separation of channels with anti-slip finish

(Width squares) O 10 1

Width channels non-slip finish P 2 0,2 Depth channels non-slip finish Q 1,5 0,2

Radio fund channels R 1 0,25

Table 3. Dimensions Lateral Handle

Tolerance in mm

Total length S 124 2 Antislip finished length T 74 2

Diameter union with the heart U 31 1 Diameter union with the head V 27 1

Diameter head W 45 1 Head end radius X 26 1 Head start radius Y 19 1

Radio union with the heart Z 10 1 Separation of channels with anti-slip finish AA 6 0,5

Width channels non-slip finish AB 2 0,2 Depth channels non-slip finish AC 1,5 0,2

Radio fund channels AD 1 0,25

Table 4. Dimensions Heart

Tolerance in mm

Total length AE 107 2 Width at 23 mm ± 2 mm from the joint with the main handle AF 60,5 2

Width at 57 mm ± 2 mm from the joint with the main handle AG 56 2

Width at 100 mm ± 2 mm from the joint with the main handle AH 31 1

Thickness in the union with the body AI 29 1 Thickness in the union with the lateral handle, lower part AJ 27 1

Thickness in the union with the lateral handle, top AK 27,5 1 Location of the side handle with respect to the connection with the main handle AL 23 1

Convex radius side parts AM 13 0,5 Concave radius union with the main handle, lateral parts. AN 10 0,5

Radius extreme lateral edges AO 5 0,5

Weight. It should be 530 g ± 30 g.

The material. The material of the tonfa-type cane must guarantee the quality of the element and compliance with the requirements established in the standard, related to the physical and mechanical properties indicated below:

- Flexibility The cane must have a flexibility of 85 mm ± 5 mm when a force of 300 N ± 10 N is applied in its central part and it must have a recovery of at least 60 mm, when said central force is removed, as verified.

Likewise, the lateral handle must withstand a force of 500 N, without suffering alterations in its physical properties such as ruptures.

- Hardness. The tonfa-type cane must have a hardness of 90 ± 5shore, when submitting to the trial.

- Compression. The element must withstand a compression of 4000N when it is tested.

Declaration of conformity of the manufacturer.

The manufacturer of the tonfa-type stick must present a declaration of conformity in the Spanish language based on the provisions of the technical standard NTC-ISO / IEC 17050-1 and must attach the supporting documentation established in the technical standard NTC-ISO / IEC 17050- 2, where it guarantees that the item to be delivered complies with the aspects indicated below:

• That the material of the tonfa-type cane has ultraviolet protection.

• That the color of the cane is dyed in mass.

• That the tonfa-type cane supports 0.1 kg x m of IZOD impact, in accordance with the provisions of NTC 943.

• That the element supports contact with chemical agents such as soap solution AATCC

1993 WOB, sulfuric acid 59.5%, hydrochloric acid 10%, sodium hydroxide 10%, without causing weakness, loss of color decomposition, changes of mass, change of dimensions, change of appearance and alteration of its physical properties, as established in the NTC 1027.

• That the element resists a temperature of 120 ºC, when it is subjected to a test in a furnace with heat circulation, without its characteristics being altered, according to what is indicated in the ASTM D 3418, ISO 11357 standard.

• That the flexibility of the element is maintained for a minimum period of 1 year.

• That the tonfa-type cane is resistant to scratching during its transport on the user's belt and strap, when subjected to contact with objects and persons.

• That all the raw materials and / or supplies used in the manufacture of the tonfa-type cane, as well as the production processes used in its manufacture, comply with all the requirements laid down in current Colombian environmental legislation.

RESTRAINTS HAND

RESTRAINTS

HAND 180

TECHNICAL SPECIFICATIONS RESTRAINTS HAND

HANDS RESTRAINTS SMITH & WESSON MODEL 1-1 UNIVERSAL

Smith & Wesson universal handcuffs are designed to suit both larger and smaller prisoners. The contoured shape of the swinging arm allow these handcuffs to open 25% larger for big wrists and close 25% smaller for thin wrists. The Model 1 chain handcuff uses the push pin double locking system. To double lock simply depress the double lock pin on the edge of the cuff with the back of your handcuff key. Chain handcuffs are more popular as they are more forgiving and less likely to injure unruly subjects. The Model 1 handcuff needs an oversize handcuff case or handcuff strap.

Smith & Wesson has a lifetime warranty on their handcuffs against manufacturer defects. These come with two keys and instructions and have a dull satin nickel finish.

• Wrist Opening: 2.40"

• Locking Positions: 30

• First notch inside perimeter: 9.40"

• Last notch inside perimeter: 5.80"

• Tightest inside width: 1.60"

• Distance between cuffs: 2.00"

• Maximum overall length: 9.85"

• Weight: 12 ounces

• Smith & Wesson Part #: 350132

RESTRAINTS LEG

RESTRAINTS

LEG 180

TECHNICAL SPECIFICATIONS RESTRAINTS LEG

LEG RESTRAINTS SMITH & WESSON MODEL SW1900

Large 14 "foot chain; High security heat treated, satin elliptical nickel contour. The Smith & Wesson handcuffs are made of the highest quality carbon steel, treated with heat, with easy pawls for quick cuffing, and double locks to prevent tampering. The interior perimeter measures 8 "to 10-3 / 4".

Shackles with 22 locking positions and a double locking pin.

• Ankle opening: 2.80".

• Locking positions: 23

• First notch inside the perimeter: 10.90".

• Last notch inside the perimeter: 8.10".

• Width of the narrows in the interior: 2.50".

• Distance between cuffs: 17.30 "(43.94cm)

• Maximum Overall length: 25.63 "(65.1cm)

• Weight: 22 oz. (623.7g).

RIOT HELMETS

RIOT HELMETS 180

TECHNICAL SPECIFICATIONS RIOT HELMETS

No. TECHNICAL DATA REQUEST

1. COLOR Black, no paint on polycarbonate is accepted

2. LABORATORY TESTS

Along with the material that is delivered as the object of the contract, the supplier must attach certification and test results by an accredited laboratory for the delivered batch, in compliance with what is stated in NTMD-0031-A2 in number 5 .

3.

PROOF OF

RESISTANCE AND

HARDNESS (HELMET)

The bidder must attach together with the NIJ certification offer issued by a qualified and accredited laboratory on behalf of the manufacturer for the proposed anti-riot helmet, with the results of destructive test tests for the offered helmets, in satisfactory compliance with the standard: NIJ 0104.02. The aforementioned certificate must have a date of issue not before 2010. In the event that the certificate is issued by a foreign certifying body, it must have the corresponding translation into Spanish. Likewise, certification of the destructive tests to which the helmet is subjected and the quantifiable results according to the ASTM impact standard D256 must be attached by a laboratory abroad or, failing that, any laboratory in the accredited national territory. Said certification must be dated not before the year 2016.

4.

CERVICAL

PROTECTOR

CERTIFICATION

RETARDANT TO THE 6-

OZ FLAME MINIMUM

Attach certification issued by the manufacturer of the helmet where they endorse the resistance of the outer lining to the flammability, according to the destructive mechanical tests developed under any of the following standards or vertical flame test methods used in protective equipment: ASTM-4108 TPP, NFPA2112, CGSB

155.20, EN531, EN532.

5. YEAR OF PRODUCTION

Attach together with the manufacturer's certification offer where it specifies that the helmets are of the date of the validity of the delivery of the elements. As well as that the material is new, not re-powered or remanufactured.

6. WARRANTY

The manufacturer must guarantee the correct operation and quality, for a minimum term of three (3) years, counted from the delivery of the same. The elements subject to guarantee must be replaced within a period not exceeding sixty (60) calendar days.

7. AFTER SALES SERVICE

The manufacturing company must guarantee the correct functioning of the elements that make up the helmet during the three (3) years following the delivery to the satisfaction of the

No. TECHNICAL DATA REQUEST National Penitentiary and Prison Institute INPEC. The manufacturing company must technically assist INPEC, in case of technical or manufacturing failures, in the place and date determined by the force during the duration of the guarantee.

Taking into account the above, the novelty must be addressed in a time no longer than 30 calendar days giving solution, rehabilitating or changing the element that is required. Once the news is notified.

8. PACKAGING

Each helmet will be packed individually, protected with a polyethylene bag and in a cardboard box, duly sealed and identified, and in turn, 6 units in cardboard boxes that must be labeled with the registered trademark and units it contains. With its user manual.

9. MANUFACTURER

CERTIFICATION

The contractor must attach together with the offer certification issued by the manufacturer, where it guarantees that the manufacturing process of the product offered, which must be of excellent conditions for the service.

10. TECHNICAL

OBSERVATION

The technical sheet of the helmet offered in the original of the manufacturer's house must be attached (if it is in a language different from Spanish, it must be translated into Spanish), where some of the most important technical data, as well as mechanical and functional details of the helmet, are attached. in the offer.

11. RECEPTION TESTS

Together with the material that is delivered as the object of the contract, the supplier must add at no additional cost, according to the stipulation in sampling table 4.2 of NTMD-0031-A2.

For the reception of the material the armament group (Armament Warehouse) will coordinate the tests, naming a technical committee in order to verify the performance, measurement and weighing according to numeral 4.2 of the NTMD-0031 -A2, with the purpose of Verify that the material received complies fully with the present technical specifications.

If all the requirements stipulated in these specifications are not met, the supplier must replace all the elements that make up the batch evaluated in the acceptance tests until satisfactory compliance with the object of the contract is achieved, for which the supplier shall have a maximum of thirty (30) calendar days, after the delivery of the goods.

Note: in case of problems in the proof of receipt with the material, no receipt certificate will be issued to satisfaction.

WALKING RESTRAINTS (TRANSPORT RESTRAINTS SW1850)

WALKING RESTRAINTS

(TRANSPORT RESTRAINTS SW1850) 10

TECHNICAL SPECIFICATIONS WALKING RESTRAINTS (TRANSPORT RESTRAINTS SW1850)

TRANSPORT RESTRAINT SMITH & WESSON MODEL SW1850

This transport retention system uses a combination of Model 1 Universal handcuffs and Model 1900, Leg Irons; both in satin nickel finish. The length of the chain between the cuffs is 32 ". The Smith & Wesson handcuffs are made of the highest quality carbon steel, treated with heat, with easy pawls for quick cuffing, and double locks to prevent tampering.

N0039 Security Equipment - SOW