Attachment_1_SOW.pdf

Attachment 1 RFQ No. 140P8418Q0087 Outfit Law Enforcement Vehicles

Attachment 1 Page 1 of 16

INSTALLATION - GENERAL REQUIREMENTS

In addition to the equipment listed by Contract Line Item (CLIN), the contractor will supply all incidental supplies, such as hardware, conductors, connectors and fuses necessary to complete the work. The contractor must utilize quality wiring, equipment, metal material and custom fabrication when integrating law enforcement packages into vehicles.

Each installation shall meet to the following standards. This is not all inclusive of every quality measure that will be checked for, but should be used as a guideline of the quality expected. All work performed will be in accordance with the standards established by the Consumer Electronics Association (CEA), Mobile Electronics Certified Professional (MECP) and/or the National Institute for Automotive Service Excellence (ASE).

All grounding locations are required to use “star washers” under the ring terminal. Check all grounds for tightness and correct crimping as per MECP best practices for making low and high current connections.

Do not share factory grounding points with aftermarket equipment to minimize the risk of damage to OEM and aftermarket equipment. If an open or unused grounding point is unavailable, please use a nut and bolt as opposed to using self-tapping screws into metal. Sand or scuff the paint at the grounding points to ensure a good connection.

Minimize the fail points of the installation wherever possible by minimal use of wire extensions and butt splices. Extension of light bar control cables is unacceptable as is the extension of wires that were cut too short off the spool.

Check all crimp points for proper crimps. The seam of the connector cannot be spread apart after the crimp. Also, the dimple of the crimp needs to be 180 degrees offset from the connector seam.

Any and all outside wire connections made (i.e. siren speaker, grille lights, inserts, wig wag, etc.) will need to be made with weather proof connectors or heat shrink used ½” on either side of the connection.

All wire runs that are out in the open and not tucked away under or behind a panel will need to be placed inside of black wire loom, zip tied to a factory wire harness (where applicable) or the framing to keep wires runs in a neat and consistent fashion.

Any pass-through wiring (wires that pass through a hole in metal) will need to have a rubber grommet installed at the pass through to prevent wire chafing and accidental grounding as well as silicone used to prevent water intrusion.

All wire termination points will need 6” of extra wire or slack for any repairs that need to be made to equipment. Neatly secure extra wiring near the connection point to provide a clean installation. All wiring runs will need to be zip tied, electrical taped, or loomed together where applicable. “Rats nest” wiring is not acceptable.

All equipment installed will be inspected for functionality and security. All parts need to be secured properly with the appropriate hardware that is in compliance with the part manufacturer and standards set by MECP best practices.

Attachment 1 Page 2 of 16

All wires and cabling will need to be run in a way that is free from pinch points, retaining clips. Sharp objects including metal edges, tucked away so the wires are not seen and checked for any cuts in the wire insulation where grounding can cause performance issues.

Every wire connection needs to be checked for proper seating and correct wiring.

Light lenses must be cleaned and debris removed from the holes that were drilled for lighting inserts.

All trim screws need to be replaced when removed for installation of equipment. If any retaining clips, trim or interior panels, or dash panels are damaged and/or broken during the removal process, they will need to be replaced with an OEM equivalent or better.

All panels and interior trim need to be fitted properly and correctly seated in position.

No carpet bulges. All carpeting must be flush and no wires run under or around vehicle pedals or moving components where vehicle operator is seated. If wire or cabling needs to be run in this area, please run and use multiple secured on all wires above drivers feet, behind knee bolster as far away as you can get it from moving parts.

All dash pieces need to be properly seated and free of damage. If installation requires modification or holes drilled in the dash, the contractor will need to get prior approval from the contracting officer. All OEM components will need to be checked for functionality prior to and after the installation has taken place. Please note any warning lights on the instrument cluster that may be on prior to the install. Do not perform the install if any warning light stays lit 10 seconds after the vehicle is started (with the exception of the TPMS light). Inform the agency of the light and have them make the necessary repairs prior to the install.

The vehicle cannot have any warning lights illuminated on the instrument cluster after the install (again with the acceptation of the TPMS light).

All antenna coax ends will need to be properly crimped as per MECP best practices. There will need to be 6” of extra coax in addition to strain relief for repairs. Strain reliefs must be used on all microphone cables to prevent damage to cable ends.

Check weather stripping for proper seating if removed.

Vehicle will be checked for any exterior and interior damage before and after installation. If you notice any damage, please inform the agency before performing the installation. The contractor may be held liable for any damage that occurs to the vehicle while it is in their possession.

All areas where fasteners are used to mount equipment will need to be checked on both sides of the mounting surface prior to drilling to prevent accidentally running in to a wire harness or OEM or aftermarket components.

Vehicles must be completely cleaned inside where the installation has taken place. Remove all metal shavings from carpet areas, drip trays, and other surfaces.

Use an anti-rust inhibitor where pass through holes are drilled through metal (i.e. light bar cabling hole, firewall pass through, and NMO coax holes).

Splicing of vehicle factory wiring is unacceptable.

Attachment 1 Page 3 of 16

CLIN 00010 & 00020: 2018 Chevy Tahoe Patrol Vehicle – Marked

Description of Work:

The contractor shall REUSE if possible and install the following items provided by the NPS.

1. Motorola XLT5000 Mobile Radio and antenna.

a. Location: Center Console.

2. Motorola radio speaker.

a. Location: center console mounted low out of the way.

3. Stalker Dual police radar unit with front and rear antennas. Dash Mount hardware included. Antenna mounts may need to be ordered.

a. Location: Front antenna hard mounted to driver side front A pillar. Rear antenna hard mounted on driver side rear D pillar. Counter unit mounted on top of dash between the A pillar and the driver information center

4. Watchguard in car camera system (DV1 with one camera)

a. Location: Industry standard location in headliner at the windshield. Mounting

Bracket may need to be ordered from WatchGuard Systems.

b. 2 in car camera systems to be installed.

5. Whelen Siren control box Model 295SLS

a. Location: center console in designated location.

b. Top button configuration (L -> R) L alley, R alley, Take down, Spot light, Blank, Gun Lock

6. Quick Cable Battery terminal wiring harness plug *Park Provided.

a. Location: Quick connect end mounted to Front Push Bumper if possible given length of provided cable.

The contractor shall SUPPLY and install the following items.

1. Whelen Liberty II Solo IH8 or IH2 WeCan series -All red/blue around with takedowns and alley lights.

a. Location: Roof mount: manufactures specifications.

2. Whelen – 6 LED Interior Traffic Advisor (or similar)/ with control head. Red, Amber center, Blue.

a. Location: interior hard mounted, rear lift gate window.

3. Whelen- IONJ or similar- Dual LED Light, Split Red/Blue.

a. Location: See Diagram, hard mounted interior rear side windows.

b. Quantity: Two

4. Whelen – ION Micron series Dual LED Light or similar, Rear Hatch. Split Red/Blue.

a. Location: Micron License Plate bracket, exterior rear hatch, near license plate.

b. Quantity: Two

5. Whelen – LINSV2 LED or similar- side mirror.

Attachment 1 Page 4 of 16

a. Location: One strobe mounted in lenses on side mirror housing facing forward.

b. Quantity: One Pair, Front

6. Whelen or similar – Head Lamp Flashers,

a. Location: Front Headlights

b. Quantity: One set

7. Whelen or similar – Rear Strobes,

a. Location: Rear Lamps

b. Quantity: One Set

8. Spotlight with mounting kit. Black.

a. Driver and Passenger A pillar mount.

9. Troy CC-WBOS-20 Wide Body w/ open Storage 20” center console and mount. With mounting options for radio and siren control box. Dual cup-holder insert, three 12 volt AC outlets shallow personal storage tray and posse box insert.

a. Location: In manufacturer specified location far forward as possible.

b. Quantity: One of each item.

10. Flexible Map Light

a. Location: Center Console

11. WeBoost Drive Sleek 4G cell phone booster (https://www.wilsonamplifiers.com/weboost-drive-sleek-4g-cell-phone-booster-kit-470135/)

a. Location: Installed with power supply hidden and power integrated into ChargeGuard system. Interior antenna positioned optimal for front passenger usage. Exterior antenna roof mounted in location not to interfere with 2-way radio antenna or reception.

b. Location: on center console or dash.

12. ChargeGuard CGX-R75 voltage monitor with timer

a. Location: Hard mounted in an accessible area near or attached to the center console (inside console if possible).

13. Setina Electronic weapons mount, vertical partition mounted AR-15 with optics/ Rem870 mount w/#2 key back-up release.

a. Location: Hard mounted on recessed panel with maximum stability. Forward facing

14. Setina prisoner partition. Model #10VS RP Coated Poly Partition WITH recessed panel.

15. Setina (or similar) rear cargo cage. Model #12VS Expanded Metal Partition.

16. Setina (or similar) front push bumper. Model PB450L. With factory mounted forward facing and side mounted LED’s. Split Red/Blue.

17. Whelen or similar -100 watt Speaker

a. Location: Mounted in industry standard position/ push bumper.

18. ALL new wiring, fuses and associated materials for all electronic wiring. Wire loom shall cover all exposed wiring or wiring in areas that may get damaged.

EXTERIOR

The contractor shall install the following items provided by the NPS.

1. Vehicle graphics package.

Attachment 1 Page 5 of 16

a. Shall include striping, and assorted stickers and lettering to be placed in accordance with instructions provided. Installer shall supply rear hatch green chevrons to match if possible.

b. Any deviation required to fit graphics onto vehicle shall be done in consultation with NPS representative.

GRAPHICS NOTE:

1) Do Not split the “U.S. Park Ranger” lettering in the middle of “Park” or “Ranger” on drivers and rear door. Adjust to split as shown above on both sides of vehicle.

2) Cut stripe around the arrowhead and gold badge when installing, rather than laying over green and silver stipe.

Spotlight on both front A pillars

Interior mounted

Split

Red/Blue

LEDs.

Undermirror

LED OR surface mounted.

Roof mounted lightbar.

Roof mounted radio antenna.

Attachment 1 Page 6 of 16

CONTRACT LINE ITEM 00030: 2018 Chevrolet Tahoe Patrol Vehicle-Marked

The contractor shall REUSE if possible and install the following items provided by the NPS.

1. Motorola XLT5000 Mobile Radio and antenna.

b. Location: Center Console.

2. Motorola radio speaker.

a. Location: center console mounted low out of the way.

3. Stalker Dual police radar unit with front and rear antennas. Dash Mount hardware included. Antenna mounts may need to be supplied by the contractor.

b. Location: Front antenna hard mounted to driver side front A pillar. Rear antenna hard mounted on driver side rear D pillar. Counter unit mounted on top of dash between the A pillar and the driver information center

Speaker Split

Red/Blue

LEDS.

Interior mounted traffic advisor.

Red/Amber/

Blue

Push bumper with built in

LED’s. Forward facing x2 and side facing each side.

Attachment 1 Page 7 of 16

4. Whelen Liberty II Solo light bar (48 inch) * may need different light mounts.

a. Location: Roof Mount: Manufacturer specifications.

5. Whelen Siren control box Model 295SLS

c. Location: center console in designated location.

d. Top button configuration (L -> R) L alley, R alley, Take down, Spot light, Blank, Gun Lock

6. Quick Cable Battery terminal wiring harness plug *Park Provided.

e. Location: Quick connect end mounted to Front Push Bumper if possible given length of provided cable.

The contractor shall SUPPLY and install the following items.

7. Whelen – 6 LED Interior Traffic Advisor (or similar)/ with control head. Red, Amber center, Blue.

a. Location: interior hard mounted, rear lift gate window.

8. Whelen- IONJ or similar - Dual LED Light, Split Red/Blue.

a. Location: See Diagram, hard mounted interior rear side windows.

b. Quantity: Two

9. Whelen – ION Micron series or similar Dual LED Light, Rear Hatch. Split Red/Blue.

a. Location: Micron License Plate bracket, exterior rear hatch, near license plate.

b. Quantity: Two

10. Whelen – LINSV2 LED or similar - side mirror.

a. Location: One strobe mounted in lenses on side mirror housing facing forward.

b. Quantity: One Pair, Front

11. Whelen or similar – Head Lamp Flashers,

a. Location: Front Headlights

b. Quantity: One set

12. Whelen or similar – Rear Strobes,

a. Location: Rear Lamps

b. Quantity: One Set

13. Spotlight with mounting kit. Black.

a. Driver and Passenger A pillar mount.

Attachment 1 Page 8 of 16

b. Quantity: two

14. Troy CC-WBOS-20 Wide Body w/ open Storage 20” center console and mount. With mounting options for radio and siren control box. Dual cup-holder insert, three 12 volt AC outlets shallow personal storage tray and posse box insert.

a. Location: In manufacturer specified location far forward as possible.

b. Quantity: One of each item.

15. Flexible Map Light

a. Location: Center Console

16. WeBoost Drive Sleek 4G cell phone booster (https://www.wilsonamplifiers.com/weboost-drive-sleek-4g-cell-phone-booster-kit-470135/)

a. Location: Installed with power supply hidden and power integrated into ChargeGuard system. Interior antenna positioned optimal for front passenger usage. Exterior antenna roof mounted in location not to interfere with 2-way radio antenna or reception.

b. Location: on center console or dash.

17. ChargeGuard CGX-R75 voltage monitor with timer

a. Location: Hard mounted in an accessible area near or attached to the center console (inside console if possible).

18. Setina prisoner partition. Model #10VS RP Coated Poly Partition WITH recessed panel.

19. Setina Electronic weapons mount, vertical partition mounted AR-15 with optics/ Rem870 mount w/#2 key back-up release.

a. Location: Hard mounted on recessed panel with maximum stability. Forward facing

20. Setina (or similar) rear cargo cage. Model #12VS Expanded Metal Partition.

21. Setina front push bumper. Model PB450L. With factory mounted forward facing and side mounted LED’s. Split Red/Blue with Whelen ION lights or similar.

22. Whelen or similar -100 watt Speaker

a. Location: Mounted in industry standard position/ push bumper.

23. ALL new wiring, fuses and associated materials for all electronic wiring. Wire loom shall cover all exposed wiring or wiring in areas that may get damaged.

2. Vehicle graphics package.

Attachment 1 Page 9 of 16

a. Shall include striping, and assorted stickers and lettering to be placed in accordance with instructions provided. Installer shall supply rear hatch green chevrons to match if possible.

b. Any deviation required to fit graphics onto vehicle shall be done in consultation

EXTERIOR

3. Vehicle graphics package.

c. Shall include striping, and assorted stickers and lettering to be placed in accordance with instructions provided. Installer shall supply rear hatch green chevrons to match if possible.

d. Any deviation required to fit graphics onto vehicle shall be done in consultation radio antenna.

Attachment 1 Page 10 of 16

GRAPHICS NOTE:

3) Do Not split the “U.S. Park Ranger” lettering in the middle of “Park” or “Ranger” on drivers and rear door. Adjust to split as shown above on both sides of vehicle.

4) Cut stripe around the arrowhead and gold badge when installing, rather than laying over green and silver stipe.

CONTRACT LINE ITEM 00040: 2018 Chevrolet Tahoe Patrol Vehicle-Unmarked

Spotlight on both front A pillars

Interior mounted

Split

Red/Blue

LEDs.

Speaker Split

Red/Blue

LEDS.

Interior mounted traffic advisor.

Red/Amber/

Blue

Push bumper with built in

LED’s. Forward facing x2 and side facing each side.

Undermirror

LED OR surface mounted.

lightbar.

Attachment 1 Page 11 of 16

The contractor shall REUSE if possible and install the following items provided by the NPS.

1. Motorola XLT5000 Mobile Radio and antenna.

a. Location: Center Console.

2. Motorola radio speaker.

a. Location: center console mounted low out of the way.

3. Stalker Dual police radar unit with front and rear antennas. Dash Mount hardware included. Antenna mounts will need to be acquired.

a. Location: Front antenna hard mounted to driver side front “A” pillar. Rear antenna hard mounted on driver side rear D pillar. Counter unit mounted on top center of dash.

4. Whelen Siren control box Model 295SLS

a. Location: center console in designated location.

b. Top button configuration (L -> R) L alley, R alley, Take down, Spot light, Blank, Gun Lock

5. Quick Cable Battery terminal wiring harness plug *Park Provided.

a. Location: Quick connect end mounted inside the Engine compartment in a place not to interfere with the normal operation of the vehicle.

The contractor shall SUPPLY and install the following items.

6. Whelen Inner Edge Solo WeCan

a. Location: Interior Visor mount manufactures specifications.

7. Whelen- 6 LED Interior Traffic Advisor (or similar) with Control Head. Red, Amber center, Blue.

a. Location: interior hard mounted on rear window.

8. Whelen- IONJ or similar - Dual LED Light, Split Red/Blue.

a. Location: See Diagram, hard mounted interior rear side windows.

b. Quantity: Two

9. Whelen – ION Micron series or similar Dual LED Light, Rear Hatch. Split Red/Blue.

a. Location: Micron License Plate bracket, exterior rear hatch, near license plate.

b. Quantity: Two

10. Whelen – LINSV2 LED or similar - side mirror.

a. Location: One strobe mounted in lenses on side mirror housing facing forward.

Attachment 1 Page 12 of 16

b. Quantity: One Pair, Front

11. Whelen ION LED or similar light head – single color (white)

a. Location: Rear passengers door or top of door panel near base of window as far forward as practical, top of the door to be utilized as side alley lights

b. Quantity: One pair (one light head on driver side, one light head on passenger side.

12. ION Super Series LED or similar- Universal mount

a. Location: Behind front grill, one pair (red/blue) center of top portion of grill, one pair (red/blue) bottom grill outside corners (See Diagram)

b. Quantity: One pair of blue and one pair of red.

13. Whelen or similar – Head Lamp Flashers,

a. Location: Front Headlights

b. Quantity: One set

14. Whelen or similar – Rear Strobes,

a. Location: Rear Lamps

b. Quantity: One Set

15. Troy CC-WBOS-20 Wide Body w/ open Storage 20” center console and mount. With mounting options for radio and siren control box. Dual cup holder insert, three 12 volt AC outlets shallow personal storage tray and posse box insert.

a. Location: In manufacturer specified location far forward as possible.

b. Quantity: One of each item.

16. Flexible Map Light

a. Location: Center Console

17. Whelen or similar -100 watt Speaker

a. Location: Mounted in industry standard position behind vehicle grill

18. ChargeGuard CGX-R75 voltage monitor with timer

a. Location: Hard mounted in an accessible area near or attached to the center console, (inside center console if possible.

19. Setina Electronic weapons mount (free standing system), AR-15 with optics/ Rem870 mount w/#2 key back-up release.

a. Location: between front seats, behind center console in industry standard position.

20. Setina (or similar) rear cargo cage. Model 12VS.

Attachment 1 Page 13 of 16

21. WeBoost Drive Sleek 4G Cell Phone Booster (https://www.wilsonamplifiers.com/weboost-drive-sleek-4g-cell-phone-booster-kit-470135/)

a. Location: Installed with power supply hidden and power integrated into ChargeGuard system. Interior antenna positioned optimal for front passenger usage. Exterior antenna roof mounted in location not to interfere with 2-way radio antenna or reception.

b. Location: Mounted on center console or dash.

22. ALL new wiring, fuses and associated materials for all electronic wiring. Wire loom shall cover all exposed wiring or wiring in areas that may get damaged.

1. Vehicle graphics package.

a. NO GRAPHICS ON THIS VEHICLE.

Programing Notes for lights and accessories. If any questions exist, please reference your Ranger point of contact.

1. Programing Notes for police lights

a. All lights shall be programmed through the Siren Controller with directional controls to the industry standard. Light position 1-All rear facing lights flash.

Position 2- All rear and forward facing lights flash-NO wigwag or takedowns.

Position 3- All lights active.

2. Programing Notes for accessories

a. The Siren Controller should function as switch for all accessories.

b. We request full functionality of PA speaker switches and radio broadcast switches compatible with the Motorola XLT 5000 mobile radio provided.

c. We request an additional “master” cut off switch mounted concealed under the console, driver’s side, mid console on bottom to shut off weapons lock system.

Attachment 1 Page 14 of 16

Inner visor light bar ION solo red/blue LED (alternating) Siren speaker mounted behind the gill

Attachment 1 Page 15 of 16

Under mount LED or

Surface mount on mirrors

Single LED’s

(white) Interior Mounted Split Red/blue LEDs

Attachment 1 Page 16 of 16

Graphics Note:

This vehicle will NOT have a graphics package. Will remain unmarked.

Split Red/blue LED’s on license plate bracket

Interior mounted traffic advisor bar.

Red/amber/blue