ADO_Commercial_Supply_Pipeline_Material_Specs__1.docx

Supplies or Services and Prices/Costs

ADO 2025 Livestock Pipeline Materials

BID SCHEDULE

2. Curb Stop Ball Valve, 1 ¼ inch dia., FIPT 8 EA $______$_________

3. Float Valve Assemblies, MIPT 6 EA $______$__________

5. Protective Metal Valve Box – 18” x 36” 13 EA $______$__________

10. Fiberglass float box: 24” x 30” with lid and 2 6 EA. $_______$___________ 1-1/4 inch FIPT bulkhead fittings.

(Delivered to: RPFO)

11. UV Resistant HDPE water storage tank delivered,

12. UV Resistant HDPE water storage tank delivered,

Total Bid (All or None) $_____________ ADO 2025 Livestock Pipeline Materials

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

1. GENERAL

A. The Bureau of Land Management Albuquerque District Office (ADO) has a requirement for livestock water pipeline materials to be delivered to the BLM Rio Puerco Field Office (RPFO) Wareyard, 1800 12 St NW, Albuquerque, NM 87104. The pipeline materials as set forth in Section B - Supplies or Services and Prices/Costs shall meet, at a minimum, the following specified manufacturers’ requirements. The water storage tanks are for the BLM Socorro Field Office (SFO), 901 S. Highway 85, Socorro, NM, 87801 and would be delivered to locations as described in the attached delivery maps. Quantity: 3- 5,000 gallon Tanks Delivered onsite - See Maps – Socorro Field Office (SFO). Quantity: 1- 5,000 gallon tank and the 2- 1,100 gallon tanks delivered to MRGCD Wareyard 2401 State Road One Socorro, NM 87801.

Contractor must allow 3 business days in advance notice for coordination of delivery.

2. MATERIALS

B. High Density Polyethylene (HDPE) Pipe: Polyethylene pipe shall carry the seal of approval of the National Sanitation Foundation NSF-PW. Nominal diameters of pipe are inside dimensions for SIDR rated pipe. All pipe shall be protected against damage by freezing, heat, sunlight, and traffic until delivered and accepted. Polyethylene pipe shall be type 4710 and meet the requirements of ASTM D 3035 for DR rated pipe. Pressure rating and DR of pipe shall be as shown on the Bid Schedule. Each roll of pipe shall be marked along its entire length with a tag that states the diameter, pressure rating, and DR. PE pipe shall be of the size and quantity shown in Section B - Supplies or Services and Prices/Costs.

C. Curb Stop Valves: Curb stop valves shall be of brass or bronze construction, have a minimum pressure rating of 300 PSIG, and shall have female iron pipe threads, have pressure rating stamped on valve housing, be pressure tight on both sides, have full port opening, have a hard chrome plated brass or stainless steel ball, have a flat head for open or close position, and have a reinforced teflon valve seat. Curb stop valves shall meet the requirements conforming to ANSI/AWWA C800-89 (ASTM B62 – Index 115 85-5-5-5). Curb stop valves shall be of the size and quantity shown in Section B - Supplies or Services and Prices/Costs.

D. Float Valve Assemblies: Float Valve Assemblies shall include a float valve, a 5/16” float valve stem, and a 6-inch Copper Ball Float. Float valves shall be of brass or bronze construction, shall have 3/4-inch male iron pipe threads (MIPT) with single lever action for horizontal installation and fluted, rotating plunger with thumb screw adjustment. Valves shall be pressure rated to 125 psi minimum, and minimum flow shall be equal to 25 gallons per minute at a pressure of 100 psi. Float valve stems shall be solid brass, 5/16”-inch diameter by 10-inch length, brass and threaded on both ends with swivel. Floats shall be 6-inch diameter copper ball floats with female thread connections 5/16” -inch - 20 SAE.

E. Air vents: Air vents shall be automatic continuous air bleed and vacuum relief type and shall be capable of releasing accumulated air when the system is under pressure. Valve shall have 2 to 150 psi minimum working pressure range, free-floating foam, plastic, or stainless steel float, shall have a minimum of 1 ½ inch diameter FIPT inlet, shall be pressure tight without leaks upon closing, be of aluminum, bronze, brass, iron, or plastic body construction, shall have female pipe threads of the diameters listed in the Bid Schedule. (Waterman AV150 or equal).

F. Protective Boxes: Protective boxes shall be 18 or 24 inch diameter galvanized steel culvert (CMP) with a lockable cast metal lid attached for a total minimum length of 36 inches.

G. Butt Fusion “Ts” for 1 ¼ inch dia. PE pipe, compatible with DR-11 200 psi 4710 PE pipe.

H. Butt Fusion “90 degree elbows” for 1 ¼ inch dia. PE pipe, compatible with DR-11 200 psi 4710 PE pipe.

I. Butt Fusion Transitions for 1 ¼ inch dia. PE pipe, MIPT, compatible with DR-11 200 psi 4710 PE pipe.

J. Water Meter Key to fit Curb Stop ball values and cast valve box lid, “Street Key combo” 5/8” diam. Rod, 30” length.

K. Fiberglass float box: 24 inches wide by 30 inches tall with bolt on lid and two (2) fiberglassed or poly 1-1/4 inch FIPT bulkhead fittings.

L. UV Resistant HDPE water storage tank(s): 5,000 gallon, low profile, one piece, dimensions: 12' diameter, not to exceed +/-8' in height, with lid and bulkhead fitting. (Tanks Delivered onsite - See Maps – Socorro Field Office (SFO). Quantity 3 Delivered to onsite Maps and 1 delivered to MRGCD Wareyard 2401 State Road One Socorro, NM 87801.

M. UV resistant HDPE water storage tank(s): 1,100 Gallon, above ground low profile 87" wide x 53" tall +/- 6" height, 183 lbs =/- 5lbs in weight empty, with lid and bulkhead fitting. Prefer green but black is allowable. Delivered to MRGCD Wareyard 2401 State Road One Socorro, NM 87801.