RFQ-Dump Body Fabrication and Install Final Copy_0001.pdf

DEPARTMENT OF INTERIOR, BUREAU OF LAND MANAGEMENT

Dump Truck Body Fabrication and Installation

Request for Quote

TABLE OF CONTENTS

GENERAL

DESCRIPTION

TRANSPORTATION AND DELIVERY OF EQUIPMENT

SUBMITTALS

DEFINITIONS & APPLICABLE STANDARDS

EQUIPMENT REQUIREMENTS

INSPECTION/ACCEPTANCE

CONTRACT TIME

WARRANTY

INSTRUCTIONS FOR QUOTE

BASIS OF AWARD

POINTS OF CONTACT

APPENDIX A

APPENDIX B

APPENDIX C

PROVISIONS

CLAUSES

GENERAL

The BLM Western Oregon Districts require the fabrication and installation of dump bodies and related equipment to (6) cab and chassis. Completed Dump Trucks will be used to haul crushed and oversize rock, hot mix asphalt, dirt and mud waste, and woody debris in the performance of road maintenance tasks on timber access roads. They will also be used to tow trailers for hauling rock, hot mix asphalt, and heavy equipment. Cab and chassis are described in the Appendix C.

DESCRIPTION

Contractor shall supply all parts, materials, labor, supplies, fluids, shipping and disposal fees necessary to complete the work, as described below.

TRANSPORTATION AND DELIVERY OF EQUIPMENT

Transport of the trucks to and from the contractor’s facility shall be provided by the BLM up to 250 miles one-way from BLM Roseburg District Office (777 N.W. Garden Valley Boulevard Roseburg, OR 9747).

Transport distances in excess of 250 miles shall be provided by the contractor. For transportation in excess of 250 miles trucks shall not be driven but shall be transported via flatbed truck/trailer or similar transportation method.

SUBMITTALS

Submit the following and receive approval in writing prior to performing the work:

• Shop drawings of the dump box with hoist assembly.

• Make and model of proposed pintle hitch, PTO, hydraulic pump and hydraulic valving.

• Shop drawings of any proposed bolt on appendages to the frame including, but not limited to the hydraulic tank, filters, and tool box.

DEFINITIONS & APPLICABLE STANDARDS

All work and materials shall comply with the following standards:

• All work shall be completed in a workmanlike manner and to all applicable industry standards.

• All work shall comply with Federal Standard 794AM/807AB

• All welding shall comply with the most current American Welding Society (AWS)

Standard Welding Procedures & Specifications (SWPS).

EQUIPMENT REQUIREMENTS

The following shall be performed on (6) trucks.

Fabricate and install a hitch plate, with pintle hitch, capable of pulling 50,000lbs.

• The pintle hitch shall be air cushioned, Premier Model 370A-281B or equivalent.

• Hitch height shall be 24”

• Pintle hitch cushion shall be plumbed to charge when trailer brakes are charged.

• (1) D-ring shall be installed on each side of the hitch, at a level lower than the hitch for the purpose of attaching trailer safety chains. The D-Rings shall be 1” and attached so that they are capable of transferring the working load limit of the ring to the truck frame.

• A removable chip spreader hitch bar shall be attached to the hitch plate to conform to the specifications in Appendix A.

• The hitch shall be covered with a rubber flap to shed rock and dirt.

• Glad hand air connections and female trailer electrical sockets shall be installed near the hitch and recessed to prevent damage.

• Air line shall be plumbed to activate air cushion hitch when OEM (Original Equipment

Manufacturer) tractor protection valve is charged.

Fabricate and install a semi elliptical dump body to the following specifications. Vendor shall ensure that the new beds are compatible with existing BLM owned slip in water tanks.

• Inside dimensions shall be 14’ long by 7’0” wide, with a 35” water level.

• The flat area in the bottom of the dump body shall be a minimum of 44” wide and the length of the box.

• Box corners shall be a 20” radius.

• All interior box surfaces shall be 3/16” Hardox 450 or equivalent

• 2 ½” wide x 5/8” thick rubber frame buffer shall be attached to the length of the long members.

• There shall be no crossmembers between the front and rear of the body.

• Provisions shall be provided on top of the top rails for 4”x8” nominal finished Douglas Fir

Sideboards.

• Sideboards shall be provided with the dump body.

• Cab guard shall be no less than 10 gage with 3/16” support arms

• The cab guard shall be no wider than the truck cab and extend 24” forward of the dump body.

• (4) 5/8” D rings shall be welded to the inside of the box walls, one in each corner of the box.

At the forward end, they shall be attached 6” to 12” from the dash panel, and 2-6” from the top of the top rail. At the back end, they shall be attached 6” to 12” from the tailgate, and 2-

6” from the top of the top rail.

Provide a driver operated tailgate latch. Latch shall hold the tailgate in contact with the back edge of the body floor and sides.

• The latch assembly shall be an over center design.

• The tailgate latch cylinder shall be MGM 5004013, or equivalent, air open, spring lock.

• Trip rod bearing blocks shall not be attached to the dump body floor and shall have a minimum clearance of 1 ¼” from the bottom of the floor.

• Latch hooks shall be no less than ½” thick.

• The latch hook pivot points shall be set inside the rear corner post for protection.

• Each latch hook shall have an adjustable, two clevis linkage.

A high lift tailgate shall be installed to allow for dumping of rip rap and oversize debris. When open, the tailgate shall be parallel to and 34”-36” above the top rails.

• The tailgate plate shall be 3/16” Hardox 450 steel and shall be 44” high.

• One center mounted roll gate shall be installed and shall have open dimensions of 16” wide x 10” high, with (2) handles for operation, one on each side.

• Spreader chains shall be 3/8" high test DOM.

• One D-ring lift eye shall be welded to the outside of the top tube, and shall be rated to lift the tailgate for removal.

• The body installation shall include an attachment point and lighting for a rear license plate, conforming with Federal Motor Vehicle Safety Standard No. 108. The attachment point shall be of sturdy construction and protected from damage during normal use of the dump box.

• The tailgate hinge arms shall be recessed as not to extend above the top of the high lift boxes.

• High lift tailgate shall include self-aligning guides.

• Hoses will be routed in a manner to be enclosed by the body to prevent damage.

The high lift tailgate hydraulic circuit shall have an adjustable needle valve flow control.

The dump body shall have a front mount external hydraulic lift.

• The inside of the dump body shall be free and clear of any hoist mounting obstructions.

• The lift cylinder shall be a single, center mounted, telescoping cylinder, trunnion mount.

Step and grab handles shall be provided on both sides of the truck to allow for three points of contact when climbing in and out of the box.

• Three access steps and one grab handle shall be provided on each side of the dump body near the truck cab.

• One inside dump body step shall be provided at each front corner.

• Steps shall have a textured surface to prevent slipping.

Fenders and mud flaps shall be installed to meet the provisions of SAE J682 and to shed materials spilled on the side of the body to the outside of the wheel tracks.

• Body fenders shall be full length constructed from at least 12 gage steel.

• Mud flaps shall be black in color and shall be installed both in front and behind drive axle tires.

• Mud flaps shall be removable without the use of tools, and shall be mounted to the dump body.

Spray guards shall be 5/16” thick belted rubber mounted on both sides of the dump body.

A hydraulic system shall be installed to allow for the operation of the truck hoist and high lift tailgate simultaneously.

• Hydraulic hoses shall be adequately supported. Supports shall not be greater than 18” apart.

• All tapered, threaded hydraulic fittings shall be installed using an anti-seize thread sealing compound. Teflon tape is not acceptable.

• All hydraulics shall be powered by a PTO driven pump.

• The PTO shall be a Muncie Hot Shift (CS8SU6807A3KX) or equivalent.

• The hydraulic pump shall be Parker # P50A342AL2525 or equivalent.

• The hydraulic control valve shall be Parker # DVA35A880MRV2SV8SV8TR99 or equivalent.

• The valve section that controls the truck hoist shall have an over run limit with an adjustable linkage.

• The hydraulic tank shall be steel.

• The hydraulic tank shall include a site glass or gage visible with the box down, and shall indicate the proper operating range.

• The hydraulic pressure hoses shall have a work rating of 3,000 PSI minimum.

• Hydraulic pressure fittings shall be JIC 37 degree or 0-ring boss.

• The suction line shall have a full flow ball valve shut off.

Dump body controls shall be mounted on a pedestal to the right of the driver’s seat and will allow for safe and controlled operation while driving.

• The hoist controls shall be a single lever, cable type and will allow for variable speed of the hoist without a change in engine speed.

• The control tower shall include switches for PTO, truck tailgate, high lift, and trailer gate.

The trailer gate switch shall be wired to a 4 pole plug, Pollak 11-404 or equivalent, near the hitch.

• The control pedestal shall be constructed and mounted such that movement of the pedestal is limited allowing for fine control of the hoist lever.

The following additional items shall be installed:

• A body Safety Prop shall be mounted on the left side of chassis and shall be capable of holding the body in a near full lift position in the event of a hydraulic system failure.

• Shovel and ax holders shall be mounted on the front panel between the cab and dump body.

• A steel tool box 18” tall x 24” wide x 24” deep shall be mounted on the driver's side frame rail.

• A bolt on apron for dumping into a chip spreader or paver hopper shall be provided. Apron shall be hinged and have flexible runner slides to allow it to fold up when it contacts the hopper. Apron shall extend 8” from the end of the box floor.

• A Pull Tarp model 8500M semi-automatic tarp or equal shall be mounted at the front of the top rails as shown in Appendix B, Fig. 1 (“A” mount, bottom roll). The pull tarp shall be bolted to the body for easy removal.

All wiring shall comply with Federal Motor Carrier Safety Regulations 393.28.

• All electrical circuits installed by body builder shall be isolated from the truck chassis with a continuous duty solenoid and blade type fuses or circuit breakers.

• Wiring harness for lighting shall be Truck Lite 50 or equivalent sealed harness.

• Truck Lite LED 60 series or equivalent stop, tail, tum lights, and LED markers shall be installed in the dump body.

• Two Truck-Lite LED 60 series or equivalent stop, tail, turn lights, one back up light shall be mounted in a removable cover plate below the body hinge.

• A backup alarm shall be provided which provides an audible warning whenever the ignition switch is on and the vehicle transmission control is in reverse. The alarm shall automatically adjust to ambient noise levels and shall conform to SAE (Society of

Automotive Engineers) J994.

• Wiring shall be stranded copper. Aluminum wire is not acceptable.

• Wire insulation shall be cross-linked polyethylene.

• Wire shall be sized so that the voltage drop for the wire run is less than 5 percent.

• Wiring for lighting on body shall be no smaller than 14 gauge.

• Wiring shall be routed to minimize exposure to tire throw-off.

• Wires shall not be routed closer than 6 inches from heat sources.

• Wires shall be installed/routed to prevent contact with moving parts.

• Wires shall be protected from sharp edges.

• Self-stripping wiring connectors (scotch locks) shall not be used.

• Lighting and reflectors shall comply with FMVSS 108.

The following standards of workmanship shall be met:

• The dump body and other fabricated components shall have good welds. A good weld will have proper penetration and be relatively uniform in appearance.

• Excessive distortion of assembled parts in not acceptable.

• All welds shall conform to or exceed American Welding Society Standards and shall provide a metal to metal bond, with adequate penetration using proper flux and or welding materials.

• Down hand welds are not recommended for ten gauge or thicker material. If down hand welds are used they shall have proper penetration.

• Some characteristics of an unacceptable weld are as follows: cracks, undercut, overlap, excessive splatter, slag entrapment, inadequate penetration, excessive distortion, blowholes, and inclusions, excessive porosity, concave or convex.

Air system installation shall conform with the following standards:

• All air hoses shall be DOT approved.

• The bend radius of airlines shall be not less than the manufacturer's recommended minimum.

• Airlines shall be installed/routed to prevent contact with moving parts.

• Airlines shall not be routed through holes or across sharp edges without protection from being chafed or cut.

• Airlines shall be adequately clamped or tied to supporting structures.

• Airlines shall be routed so that low points are minimized.

• Hoses shall be of sufficient length to prevent stretching, distortion, or disconnecting.

Surface treatments shall comply with the following:

• All metal surfaces shall be free of contaminates that may cause loss of adhesion (Grease, oil, etc.).

• The first primer undercoat shall be a metal self-etching primer.

• The second primer undercoat shall be an epoxy base. Primer shall be lead and chromate free.

• Film thickness of second undercoat shall be 2.0 mils or greater dry.

• Topcoat shall be Low VOC high solids acrylic urethane with a film thickness of 3 to 5 mils.

• Substrates must be between 50 and 110 degrees in a controlled environment during the primer and paint application.

• Compressed air supply shall not exceed 20% humidity during the spray process.

An owner’s manual shall be provided with each dump body.

• The manual shall include sufficient information to allow for the safe operation of the dump body.

• The manual shall include sufficient information to identify and order replacement parts.

• The manual shall include electrical and hydraulic schematics.

INSPECTION/ACCEPTANCE

Contractor shall notify the Government in writing when fabrication of the first dump body is

50% is complete. Government shall complete an inspection within (2) business days of receiving notice and either accept the work as performed or furnish the contractor with a punch list of items needing to be performed or re-worked.

Contractor shall notify the Government in writing when fabrication of the first dump body is complete, and before final paint. Government shall complete an inspection within (2) business days of receiving notice and either accept the work as performed or furnish the contractor with a punch list of items needing to be performed or re-worked.

Contractor shall notify the Government in writing when installations have been completed and the dump trucks are ready for inspection. Government shall complete an inspection within two (2) business days of receiving notice and either accept the work as performed or furnish the contractor with a punch list of items needing to be performed or re-worked.

CONTRACT TIME

Completion of the first truck shall be within a maximum of 45 calendar days of delivery of the cab and chassis to the Contractor’s facility, and shall be a maximum of 30 calendar days for each subsequent truck.

WARRANTY

Contractor will provide a one-year warranty on all parts and labor and pass on to the Government any manufacturer extended warranty if beyond one-year for parts. The contractor shall have

Service/Maintenance support within 250 miles of the BLM Roseburg District Office (777 N.W. Garden

Valley Boulevard Roseburg, OR 9747).

INSTRUCTIONS FOR QUOTE

Quote shall include the vendors approach on how it will accomplish this requirement. Quote shall include the vendors facility location and the location, if different, for the Service/Maintenance Support. Quote shall include calendar date for work completion.

All quotes shall arrive by 9/9/2020, 1:00PM Mountain Daylight Time (MDT). Quotes are to be emailed to

Contracting Officer Emmett Larson (elarson@blm.gov) and Contract Specialist, Katherine “Katie” Jang

(kjang@blm.gov).

Questions are due by 9/1/2020 by 4:00 PM MDT to Katie Jang with Contracting Officer Emmett Larson copied.

BASIS OF AWARD

Award will be made based on lowest price technically acceptable. Vendor shall provide a breakdown of the firm fixed quoted price by the following two pricing elements:

1. Dump Truck Body Fabrication/Installation

2. Transportation costs, if applicable, in excess of the 250 miles provided by BLM.

POINTS OF CONTACT

BLM Contracting Officer:

Emmett Larson

National Operations Center

(303)236-9473, elarson@blm.gov

BLM Contract Specialist:

Katherine “Katie” Jang

National Operations Center

(303)236-3586, kjang@blm.gov

BLM Contracting Officer Representative (COR):

Perry Coats

Equipment Specialist

(303) 236-0020, pcoats@blm.gov mailto:elarson@blm.gov mailto:kjang@blm.gov mailto:pcoats@blm.gov

APPENDIX A

Chip Spreader Tow Bar Specifications

• 2” diameter solid steel round bar

• Mounting ears to be ½” steel plate

• 15” wide between mounting ears

• 12” minimum clearance above ground surface when sitting on flat level surface

• 7.5” minimum clearance between top of tow bar and lowest point of pintle hitch

APPENDIX B

APPENDIX C

Databook Origin TCO # Description Value

PRICE LEVEL INFORMATION

PRL-19M 001 M2 PRL-19M (EFF:1/15/19)

GENERAL APPLICATION

INFORMATION

AA1-003 D

TRUCK/TRAILER

CONFIGURATION

AA6-001 D

DOMICILED, USA 50 STATES

(INCLUDING CALI

D

FORNIA AND CARB OPT-IN

STATES)

A85-011 D CONSTRUCTION SERVICE

AA3-004 D END DUMP BODY

AA2-005 D FLATBED TRAILER

AH6-001 D SINGLE (1) TRAILER

AA5-006 H

TERRAIN/DUTY: 10% (SOME)

OF THE TIME, IN

H

TRANSIT, IS SPENT ON NON-

PAVED ROADS

AB5-003 D

MAINTAINED GRAVEL OR

CRUSHED ROCK - MOST

SEVERE IN-TRANSIT

(BETWEEN SITES) ROAD

D SURFACE

AB1-020 D

MAXIMUM 20% EXPECTED

GRADE

AA4-005 D

BUILDING MATERIAL

COMMODITY

A84-1GM D

GOVERNMENT BUSINESS

SEGMENT

A66-99D D

EXPECTED FRONT AXLE(S)

LOAD

20000 LBS

A68-99D D

EXPECTED REAR DRIVE

AXLE(S) LOAD

46000 LBS

A63-99D D

EXPECTED GROSS VEHICLE

WEIGHT CAPACITY

66000 LBS

A70-99D D

EXPECTED GROSS

COMBINATION WEIGHT

80000 LBS

AC8-99D S

CALC'D BACK OF CAB TO

REAR SUSP C/L (CA)

149.016 IN

AL8-99D S

CALC'D CAB TO BODY (INCL 2"

CLEARANCE)

15.78 IN

AL4-99D S

CALC'D FRAME LENGTH BACK

OF CAB

220.866 IN

AL6-99D S

CALC'D BODY AFT OF EOF

(+=BODY OVERHANG)

-205.087 IN

AM1-99D S

CALC'D OVERALL LENGTH AT

BODY OR EOF

333.268 IN

AC3-99D S

CALC'D VEHICLE SPEED @

GOVERNED ENG RPM

84.923 MPH

A89-99D H 002

BRAKING-EXPECTED CAB TO

BODY CLEARANCE

15 IN

BACK OF CAB COMPONENTS

REQUIRE ADDITIONA

L CAB TO BODY CLEARANCE

AF7-99D D

BRAKING-EXP CG OF

BODY&LOAD ABOVE FRAME

32 IN

AK2-99D S

BRAKING-MAX CG OF LOAD

ABOVE FRAME @GVWR

32 IN

AM3-99D S

CALC'D FRAME HEIGHT @

REAR SUSP-EXP LOAD

40.385 IN

AR1-99D S

CAL'D FRAME HT AT FRONT

SUSP-UNLADEN

42.105 IN

AM2-99D S

CALC'D FRAME HEIGHT @

REAR SUSP-UNLADEN

42.76 IN

AM0-99D S

TOP OF FRM TO RR TIRE TOP-

UNLD

0.86 IN

ALG-99D S

CALC'D CAB HEIGHT ABOVE

FRAME

68.414 IN

ALJ-99D S

CALC'D CAB HEIGHT ABOVE

GROUND; EXP LOAD

107.94 IN

ALH-99D S

CALC'D CAB HEIGHT ABOVE

GROUND; UNLADEN

110.704 IN

AF3-2C2 H COLUMBIA BODY

CUSTOMER TO INSTALL THE

BODY. WILL USE

10/12 YARD ELLIPITICAL DUMP

BODY.

MAXIMUM GVW & AXLE

SYSTEM CAPACITIES

A61-99D S

CALC'D MAX CAPACITY

FRONT AXLE(S)TOTAL

20000 LBS

A59-99D S

CALC'D MAX CAPACITY DRIVE

AXLE(S) TOTAL

46000 LBS

A60-99D S

CALC'D MAX CAP PUSHER/TAG

AXLE(S) TOTAL

0 LBS

A62-99D S

RATED MAXIMUM VEHICLE

CAPACITY - GVWR

66000 LBS

BASE MODEL

001-175 D

M2 112 CONVENTIONAL

CHASSIS

F 8244 R 6026

004-221 D 2021 MODEL YEAR SPECIFIED

995-1AF D

FREIGHTLINER LEVEL III

WARRANTY

002-004 D SET BACK AXLE - TRUCK

019-001 D

TRAILER TOWING PROVISION

AT END OF FRAME

F 10 R 10

D FOR TRUCK

003-001 D

LH PRIMARY STEERING

LOCATION

ENGINE

101-2XY D

DETROIT DD13 12.8L 505 HP @

1625 RPM, 19

00 GOV RPM, 1850 LB/FT @ 975

RPM

99C-017 D

2016-2019 ONBOARD

DIAGNOSTICS/2010 EPA/C

ARB/FINAL GHG17

99X-019 S

OBD 2019 MISFIRE

MONITORING

99Z-004 S

VEHICLE IS SUBJECT TO EPA

GHG14/GHG17, D

S

OES NOT HAVE REGULATORY

VEHICLE SPEED LI

MITER (VSL) OR AUTOMATIC

ENGINE SHUTDOWN

S (AES)

99D-011 D

2008 CARB EMISSION

CERTIFICATION - CLEAN

IDLE (INCLUDES 6X4 INCH

LABEL ON LOWER

FORWARD CORNER OF DRIVER

DOOR)

9EE-004 S

J1939 ELECTRICAL

ARCHITECTURE

992-001 S

50 STATE EMISSIONS

CERTIFICATION

28F-007 D

ENGINE AFTERTREATMENT

DEVICE, AUTOMATIC

OVER THE ROAD ACTIVE

REGENERATION AND DA

SH MOUNTED SINGLE

REGENERATION REQUEST/I

D NHIBIT SWITCH

79A-065 D 65 MPH ROAD SPEED LIMIT

79B-000 D

CRUISE CONTROL SPEED LIMIT

SAME AS ROAD

D SPEED LIMIT

79C-998 D

NO DRIVER FUEL ECONOMY

INCENTIVE

79D-998 H 002 NO PROGRESSIVE SHIFTING

79E-998 D

NO LOW RANGE TORQUE

PROTECT

79F-998 D NO FLEET MANAGEMENT

79G-006 D

5 MINUTES IDLE SHUTDOWN

WITH CLUTCH AND

D SERVICE BRAKE OVERRIDE

79J-998 D

NO PTO SHUTDOWN

79K-008 D

PTO MODE ENGINE RPM LIMIT

- 1150 RPM

79L-998 D

PTO MODE THROTTLE

OVERRIDE DISABLED

79M-002 D

PTO MODE BRAKE OVERRIDE -

SERVICE BRAKE

APPLIED OR PARK BRAKE NOT

APPLIED

79N-001 D

PTO MODE CLUTCH OVERRIDE

- CLUTCH ENABLE

D D

79P-001 D

PTO RPM WITH CRUISE SET

SWITCH - 600 RPM

79Q-001 D

PTO RPM WITH CRUISE

RESUME SWITCH - 600

D RPM

79R-998 D NO PTO MODE COOLING FAN

79S-001 D

PTO MODE CANCEL VEHICLE

SPEED - 5 MPH

79T-001 D

PTO MODE RPM INCREMENT -

25 RPM

79U-004 D

PTO GOVERNOR RAMP RATE -

100 RPM PER SEC

D OND

79V-998 D NO PTO MODE DPF REGEN

79W-001 D ONE REMOTE PTO SPEED

79X-005 D

PTO SPEED 1 SETTING - 900

RPM

79Y-998 D NO PTO 2 SET SPEED

79Z-998 D NO PTO 3 SET SPEED

80A-998 D

NO ALTERNATE ROAD SPEED

LIMIT

87W-998 S

NO PTO MODE ENG RPM LIMIT,

PTO 2

87X-998 S

PTO 3

87Y-998 S

PTOEM

87Z-998 S

REMOTE

88X-998 S NO PTO 1 REMOTE SET SPEED

88Y-998 S NO PTO 2 REMOTE SET SPEED

88Z-998 S NO PTO 3 REMOTE SET SPEED

80B-998 D

NO CHECK ENGINE LIGHT ON

OVERSPEED

80C-998 D

NO ENGINE BRAKE WITH

CRUISE CONTROL

80D-001 D

SOFT CRUISE CONTROL

ENABLED

80E-998 D

NO ENGINE FAN WITH

RETARDER

80F-998 D NO MAINTENANCE MONITOR

80G-001 D PTO MINIMUM RPM - 600

80S-998 S NO PTO 1 CONTROLS

80T-998 S NO PTO 2 CONTROLS

80U-998 S NO PTO 3 CONTROLS

80V-998 S

NO ENGINE MOUNT PTO

CONTROLS

85P-998 S

NO REAR PTO TRANSMISSION

RANGE

85K-998 S NO PTO 1 J1939 CONTROL

85L-998 S NO PTO 2 J1939 CONTROL

85M-998 S NO PTO 3 J1939 CONTROL

85N-998 S

NO ENGINE MOUNT PTO J1939

CONTROL

80H-998 D

NO ACCELERATION

MANAGEMENT

80J-998 D

NO REGEN INHIBIT SPEED

THRESHOLD

80R-000 S

DRIVELINE TORQUE

PROTECTION - ENABLED

80Y-998 S

NO CRUISE CONT-

UPPER/LOWER LIMITS

84E-998 D

NO TCU-PRIMARY MODE SHIFT

SCH

84F-998 D

NO TCU-SECONDARY MODE

SHIFT SCH

84G-998 D

NO TCU-PRIMARY MODE SHIFT

SPEED

84H-998 D

NO TCU-SECONDARY MODE

SHIFT SPEED

84J-998 D

NO TCU-ENGINE BRAKE

PRESELECT

84K-998 D

NO TCU-ENGINE BRAKE ALT

PRESELECT

84M-998 D

TCU-PUMP MODE OPTION NOT

CONFIGURED

84N-998 D

NO TCU-ENGINE LOAD

REDUCTION FUNC

85B-998 D

TCU-RANGE INDICATION NOT

85E-998 D

TCU-MAX PTO ENGINE SPEED

ENGAGEMENT NOT

D CONFIGURED

85F-998 D

TCU-MAX PTO ENGINE SPEED

OPERATION NOT C

D ONFIGURED

85G-998 D

TCU-MAXIMUM PTO OUTPUT

SPEED ENGAGEMENT

D NOT CONFIGURED

85H-998 D

TCU-MAXIMUM PTO OUTPUT

SPEED OPERATION N

D OT CONFIGURED

ENGINE EQUIPMENT

13E-001 D STANDARD OIL PAN

105-001 D

ENGINE MOUNTED OIL CHECK

AND FILL

104-998 D

NO ENGINE OIL

DRAIN/SAMPLE

133-004 D ONE PIECE VALVE COVER

014-1BX D

SIDE OF HOOD AIR INTAKE

WITH NFPA COMPLI

ANT EMBER SCREEN AND FIRE

RETARDANT DONA

D LDSON AIR CLEANER

124-1D7 D

DR 12V 160 AMP 28-SI

QUADRAMOUNT PAD ALT

ERNATOR WITH REMOTE

BATTERY VOLT SENSE

292-236 D

(3) DTNA GENUINE, FLOODED

STARTING, MIN

3000CCA, 555RC, THREADED

STUD BATTERIES

290-017 D

BATTERY BOX FRAME

MOUNTED

281-001 D

STANDARD BATTERY

JUMPERS

282-003 H

SINGLE BATTERY BOX FRAME

MOUNTED LH SIDE

H BACK OF CAB

291-017 D

WIRE GROUND RETURN FOR

BATTERY CABLES WI

TH ADDITIONAL FRAME

GROUND RETURN

289-001 D

NON-POLISHED BATTERY BOX

COVER

33M-998 D

NO AUXILIARY POWER

DISTRIBUTION MANAGEME

D NT

293-061 H

POSITIVE LOAD DISCONNECT

WITH CONTROL SW

F 2

H

ITCH WITH LOCKING

PROVISION MOUNTED OUTS

H IDE OF CAB

LOCATE NEAR BATTERY BOX N/C

QUOTE

ASSIGNED QUOTE EVXD

2006040705

295-003 D

POSITIVE AND NEGATIVE

POSTS FOR JUMPSTAR

F 4

D

T CHASSIS MOUNTED LH BACK

OF CAB

180-100 D

EATON ADVANTAGE 15-1/2

INCH SELF ADJUSTI

D NG CLUTCH

183-008 D

TORQUE LIMITING CLUTCH

BRAKE

181-002 D

ZERK FITTING WITH

EXTENSION HOSE AT CLUT

D CH RELEASE BEARING

182-005 D

HYDRAULIC CLUTCH

CONTROL

107-044 D

BW MODEL BA-921 19.0 CFM

SINGLE CYLINDER

AIR COMPRESSOR WITH

SAFETY VALVE

108-002 D

STANDARD MECHANICAL AIR

COMPRESSOR GOVER

D NOR

131-013 D

AIR COMPRESSOR DISCHARGE

LINE

152-040 D

ELECTRONIC ENGINE

INTEGRAL WARNING AND D

D ERATE PROTECTION SYSTEM

128-002 D JACOBS COMPRESSION BRAKE

016-1C2 D

RH OUTBOARD UNDER STEP

MOUNTED HORIZONTA

F 30 R 25

D

L AFTERTREATMENT SYSTEM

ASSEMBLY WITH RH

B-PILLAR MOUNTED

VERTICAL TAILPIPE

239-026 D

10 FOOT 06 INCH (126 INCH+0/-

5.9 INCH) E

D XHAUST SYSTEM HEIGHT

233-998 D

NO EXHAUST BRIGHTWORK

(PLAIN)

237-1CR D

RH CURVED VERTICAL

TAILPIPE B-PILLAR MOU

D NTED ROUTED FROM STEP

23U-001 D

6 GALLON DIESEL EXHAUST

FLUID TANK

43W-001 S

STANDARD DIESEL EXHAUST

FLUID SYSTEM COO

S LANT PLUMBING

30N-003 D

100 PERCENT DIESEL EXHAUST

FLUID FILL

23Z-998 D

NO DIESEL EXHAUST FLUID

TANK COVER

43X-002 D

LH MEDIUM DUTY STANDARD

DIESEL EXHAUST F

D LUID TANK LOCATION

23Y-002 H

DIESEL EXHAUST FLUID PUMP

MOUNTED AFT OF

H DIESEL EXHAUST FLUID TANK

43Y-001 D

STANDARD DIESEL EXHAUST

FLUID TANK CAP

242-011 D

ALUMINUM

AFTERTREATMENT

DEVICE/MUFFLER/T

D AILPIPE SHIELD(S)

273-036 D

BORG WARNER (KYSOR) REAR

AIR ON/OFF ENGI

D NE FAN CLUTCH

276-001 D

AUTOMATIC FAN CONTROL

WITHOUT DASH SWITC

D H, NON ENGINE MOUNTED

110-068 D

DDC SUPPLIED ENGINE

MOUNTED FUEL FILTER/

FUEL WATER SEPARATOR

WITH WATER-IN-FUEL

D INDICATOR

118-001 D FULL FLOW OIL FILTER

120-998 D NO COOLANT FILTER

266-069 D 1400 SQUARE INCH RADIATOR

103-039 D

ANTIFREEZE TO -34F, OAT

(NITRITE AND SIL

ICATE FREE) EXTENDED LIFE

COOLANT

171-007 D

GATES BLUE STRIPE COOLANT

HOSES OR EQUIV

D ALENT

172-001 D

CONSTANT TENSION HOSE

CLAMPS FOR COOLANT

D HOSES

270-019 D

HDEP VARIABLE SPEED

COOLANT PUMP AND RAD

D IATOR DRAIN VALVE

168-998 D NO RADIATOR/OIL PAN GUARD

360-998 D NO FRONT ENGINE PTO

361-998 D NO REAR ENGINE PTO

138-005 D

PHILLIPS-TEMRO 1500

WATT/115 VOLT BLOCK

F 4

D HEATER

141-998 D

NO COOLANT HEATER -

GAS/DSL

166-998 D NO OIL PREHEATER

140-053 D

BLACK PLASTIC ENGINE

HEATER RECEPTACLE M

D OUNTED UNDER LH DOOR

134-001 D

ALUMINUM FLYWHEEL

HOUSING

132-998 D NO AIR INTAKE WARMER

155-075 D

MITSUBISHI 12V MOD 3.175-

DP60 STARTER WI

TH INTEGRATED MAGNETIC

SWITCH

TRANSMISSION & EQUIPMENT

342-1BP H

EATON FULLER RTLO-18918B

TRANSMISSION

F 90 R 40

352-998 D

NO AUXILIARY

TRANSMISSION

343-998 D

NO TRANS CONTROL

UNIT/SOFTWARE

84B-998 D NO TCU-VOCATIONAL RATING

84C-998 D

NO TCU-PRIMARY MODE:

GEARS

84D-998 D

NO TCU-SECONDARY MODE:

GEARS

341-017 D

MAGNETIC PLUGS, ENGINE

DRAIN, TRANSMISSI

ON FILL AND DRAIN, AXLE(S)

FILL AND DRAI

D N

345-001 D

PAINTED SHIFT LEVER, SOLID

LINKAGE

97G-998 D

NO TRANSMISSION

PROGNOSTICS

348-998 D

NO TRANSMISSION

ACCESSORIES

347-002 D ALUMINUM CLUTCH HOUSING

370-015 D

WATER TO OIL TRANSMISSION

COOLER, IN RAD

F 15

D IATOR END TANK

346-998 D

NO TRANSMISSION OIL CHECK

AND FILL

368-998 D

NO EXTERNAL TRANSMISSION

OIL FILTER

84U-998 D

TCU DRIVER SWITCH INPUTS

NOT SUPPORTED

84V-998 D

TCU-DIRECTION CHNG,NOT

353-998 D

NO WIRING-VEHICLE

INTERFACE

34C-998 D

NO AUX/ACC TRANSMISSION

WIRING

362-1T6 D

CUSTOMER INSTALLED

CHELSEA 489 SERIES PT

D O

363-003 D

PTO MOUNTING, BOTTOM OF

MAIN TRANSMISSIO

D N

375-998 D NO AUXILIARY OIL COOLER

377-998 D NO POWER DIVIDER

373-998 D NO TRANSFER CASE

376-998 D

NO SHIFT CONTROL,

TRANSFER CASE

371-998 D

NO AUX TRANS/TRANSFER

CASE MTD POWER

D TAKEOFF

35T-003 D

SYNTHETIC TRANSMISSION

LUBE

385-998 D

NO MAIN DRIVELINE

HARDWARE

FRONT AXLE, SUSPENSION &

EQUIPMENT

400-1BB D

DETROIT DA-F-20.0-5 20,000#

FL1 71.0 KPI

F 190

D

/3.74 DROP SINGLE FRONT

AXLE

398-998 D NO FRONT AXLE RATIO

389-998 D NO FRONT AXLE DRIVESHAFT

402-1B1 D

MERITOR EX-L AIR DISC

FRONT BRAKES

F 10

403-002 D

NON-ASBESTOS FRONT BRAKE

LINING

419-004 D FRONT DISC BRAKE ROTORS

427-998 D

NO FRONT BRAKE DUST

SHIELDS

409-006 D FRONT OIL SEALS

408-001 D

VENTED FRONT HUB CAPS

WITH WINDOW, CENTE

D R AND SIDE PLUGS - OIL

416-022 D

STANDARD SPINDLE NUTS FOR

ALL AXLES

404-094 S

AIR DISC LONGSTROKE FRONT

BRAKE CHAMBERS

405-030 D

FRONT AIR DISC BRAKE

INTERNAL ADJUSTERS

536-055 D

TRW THP-60 POWER STEERING

WITH RCH45 AUX

F 130

D ILIARY GEAR

537-005 S STEEL STEERING SHAFT

539-003 D POWER STEERING PUMP

534-003 D

4 QUART POWER STEERING

RESERVOIR

533-001 D

OIL/AIR POWER STEERING

COOLER

40T-002 D

CURRENT AVAILABLE

SYNTHETIC 75W-90 FRONT

D AXLE LUBE

620-006 D

20,000# FLAT LEAF FRONT

SUSPENSION

F 310

619-004 D

GRAPHITE BRONZE BUSHINGS

WITH SEALS - FR

D ONT SUSPENSION

62G-998 D

NO FRONT SUSPENSION

OPTIONS

62H-998 D

NO FRONT SUSPENSION

SPRING BRACKET OPTIO

D NS

629-998 D NO FRONT SWAYBAR

410-998 D NO FRONT SHOCK ABSORBERS F -30

REAR AXLE, SUSPENSION &

EQUIPMENT

420-103 D

RT-46-160 46,000# R-SERIES

TANDEM REAR A

R 470

D XLE

421-373 D 3.73 REAR AXLE RATIO

424-001 D

IRON REAR AXLE CARRIER

WITH STANDARD AXL

D E HOUSING

382-998 D NO (#1) DRIVELINE

386-044 D

RPL25 MERITOR MAIN

DRIVELINE

F 40 R 40

388-039 D

RPL20 MERITOR INTERAXLE

DRIVELINE

393-998 D NO DRIVELINE GUARD

452-006 H

DRIVER CONTROLLED

TRACTION DIFFERENTIAL

R 40

H - BOTH TANDEM REAR AXLES

878-022 D

(1) INTERAXLE LOCK VALVE,

(1) DRIVER CON

TROLLED DIFFERENTIAL LOCK

FORWARD-REAR A

XLE VALVE AND (1) REAR-

REAR AXLE VALVE

87A-002 D

BUZZER AND BLINKING LAMP

WITH EACH INTER

AXLE LOCK SWITCH,

INTERAXLE UNLOCK DEFAU

D LT WITH IGNITION OFF

87B-005 D

BUZZER AND BLINKING LAMP

WITH EACH MODE

SWITCH, DIFFERENTIAL

UNLOCK WITH IGNITIO

D N OFF, ACTIVE <5 MPH

423-1A4 D

MERITOR EX-L OPTIMIZED

AXIAL AIR DISC RE

R -50

D AR BRAKES

433-002 D

NON-ASBESTOS REAR BRAKE

LINING

434-003 D

STANDARD BRAKE CHAMBER

LOCATION

451-005 D REAR DISC BRAKE ROTORS

425-002 D REAR BRAKE DUST SHIELDS R 10

440-006 D REAR OIL SEALS

435-998 D

NO DRIVELINE PARKING

BRAKE

426-094 D

AIR DISC LONGSTROKE 2-

DRIVE AXLES SPRING

R 20

D PARKING CHAMBERS

428-030 D

REAR AIR DISC BRAKE

INTERNAL ADJUSTERS

876-998 D

NO AIR PP/ELECT AXLE

SHIFT,CAB

87C-998 D

NO DRIVE/SHIFT AXLE

WIRING/LOGIC

898-998 D

NO AIR PP/ELECT-AXLE

SHIFT,CHAS

41T-002 D

CURRENT AVAILABLE

SYNTHETIC 75W-90 REAR

D AXLE LUBE

622-269 D

HENDRICKSON HN462 @46,000#

REAR SUSPENSI

R 500

D ON

034-998 D

NO REAR SUSPENSION

PACKAGE

621-035 D

HENDRICKSON HN 400/460 -

9.56" RIDE HEIG

D HT

431-001 D

STANDARD AXLE SEATS IN

AXLE CLAMP GROUP

624-009 D 54 INCH AXLE SPACING

628-010 D

HENDRICKSON

HN,HAULMAAX AND

ULTIMAAX SER

IES STEEL BEAMS WITH BAR

PIN

888-998 D

NO DUMP VALVE/SWITCH FOR

AIR SUSPENSION

87D-998 D

NO REAR AIR SUSPENSION

VALVE WIRING/

D LOGIC

910-998 D

NO REAR CHASSIS

SUSPENSION AIR PIPING

623-006 D

FORE/AFT AND TRANSVERSE

CONTROL RODS

630-998 D

NO REAR SUSPENSION

STABILIZER

439-002 D

REAR SHOCK ABSORBERS -

TWO AXLES (TANDEM

D )

035-998 D NO DEAD AXLE PACKAGE

443-998 D NO PUSHER OR TAG AXLE

456-998 D NO PUSHER/TAG BRAKES

457-998 D

NO BRAKE LINING-

PUSHER/TAG(SCO)

448-998 D

NO REAR BRAKE

DRUMS/ROTORS FOR

PUSHER/TA

D G

429-998 D

NO PUSHER/TAG BRAKE DUST

SHIELDS

442-998 D NO PUSHER OR TAG OIL SEALS

444-998 D NO PUSHER OR TAG HUB CAPS

445-998 D

NO PUSHER OR TAG BRAKE

CHAMBERS

458-998 D

NO PUSHER/TAG SLACK

ADJUSTERS

626-998 D

NO PUSHER OR TAG

SUSPENSION

874-998 D NO PUSHER/TAG AXLE LIFT

896-998 D NO PLUMBING FOR LIFT AXLE

87F-998 D NO LIFT AXLE WIRING/LOGIC

BRAKE SYSTEM

018-002 D AIR BRAKE PACKAGE

490-101 D

WABCO 4S/4M ABS WITH

TRACTION CONTROL, W

D IH ATC OFF-ROAD SWITCH

871-001 D

REINFORCED NYLON, FABRIC

BRAID AND WIRE

D BRAID CHASSIS AIR LINES

46E-001 S

STANDARD AIR

MANAGEMENT UNIT

904-001 D

FIBER BRAID PARKING BRAKE

HOSE

412-001 D

STANDARD BRAKE SYSTEM

VALVES

46D-002 D

STANDARD AIR SYSTEM

PRESSURE PROTECTION

D SYSTEM

413-002 D STD U.S. FRONT BRAKE VALVE

432-003 D

RELAY VALVE WITH 5-8 PSI

CRACK PRESSURE,

NO REAR PROPORTIONING

VALVE

480-088 D

WABCO SYSTEM SAVER HP

WITH INTEGRAL AIR

D GOVERNOR AND HEATER

483-998 D NO AIR SYSTEM OIL FILTER

479-003 D

AIR DRYER MOUNTED

INBOARD ON LH RAIL

460-008 D

STEEL AIR BRAKE

RESERVOIRS MOUNTED INSID

D E RAIL

46A-998 D NO AUXILIARY AIR TANK

607-998 H 002

CHASSIS CONFIGURATION -

NONE

clear under rail provided by 460 code

477-004 D

PULL CABLES ON ALL AIR

RESERVOIR(S)

485-998 D

NO EXTERNAL CHARGING

GLADHAND

481-998 D NO TRAILER AIR HOSE

476-998 D NO AIR HOSE HANGER

914-001 D

AIR CONNECTIONS TO END OF

FRAME WITH GLA

D HANDS FOR TRUCK AND NO

DUST COVERS

919-001 D

(1) ADDITIONAL AIR SWITCH

WITH PLUMBING

F 5 R 5

D TO END OF FRAME

484-998 D

NO TRAILER CABLE AND

GLAD HANDS STORAGE

296-010 D

PRIMARY

CONNECTOR/RECEPTACLE

WIRED FOR S

EPARATE STOP/TURN, ABS

CENTER PIN POWERE

D D THROUGH IGNITION

297-001 D

SAE J560 7-WAY PRIMARY

TRAILER CABLE REC

EPTACLE MOUNTED END OF

FRAME

335-004 D

UPGRADED CHASSIS

MULTIPLEXING UNIT

32A-002 D

UPGRADED BULKHEAD

MULTIPLEXING UNIT

87P-001 D

CAB AUXILIARY POWER

CABLE

F 5

308-998 D

NO SUPPLEMENTAL TRAILER

CABLE WIRING

331-998 D

NO SUPPLEMENTAL J560 7-

WAY TRAILER ABS R

D ECEPTACLE

30K-998 D

NO HIGH CURRENT

RECEPTACLE/WIRING

30L-998 D

NO HIGH CURRENT

TRAILER/BODY CABLE

310-998 D

NO TRAILER ELECTRICAL

CABLE

FRAME & WHEELBASE

545-545 D

5450MM (215 INCH)

WHEELBASE

546-102 D

7/16X3-9/16X11-1/8 INCH STEEL

FRAME (11.

F 270 R 230

D

11MMX282.6MM/0.437X11.13

INCH) 120KSI

547-001 H

1/4 INCH (6.35MM) C-CHANNEL

INNER FRAME

F 208 R 403

H REINFORCEMENT

548-998 D

NO OUTER FRAME

REINFORCEMENT

549-998 D NO FRONT FRAME EXTENSION

552-039 D

1825MM (72 INCH) REAR

FRAME OVERHANG

F -30 R 130

AB8-99D S

CALC'D FRAME SLOPE @

FRT/RR SUSP RATINGS

0.557 %

553-001 D SQUARE END OF FRAME

554-998 D

NO BUMPER/UNDERRIDE

GUARD

550-001 D

FRONT CLOSING

CROSSMEMBER

559-001 D

STANDARD WEIGHT ENGINE

561-001 D

STANDARD CROSSMEMBER

BACK OF

D TRANSMISSION

562-001 D

STANDARD MIDSHIP #1

CROSSMEMBER(S)

560-008 S

UNDER OR OVERSLUNG

565-001 D

STANDARD SUSPENSION

572-001 D

STANDARD REARMOST

AL5-99D S

CALC'D BUMPER TO REAR

TOWING C/M FACE

333.268 IN

587-998 D NO REAR TOWING DEVICE

CHASSIS EQUIPMENT

674-998 D

NO LH OR RH BACK OF CAB

ACCESS

592-998 D NO DECK PLATE

556-1AP D

THREE-PIECE 14 INCH PAINTED

STEEL BUMPER

D WITH COLLAPSIBLE ENDS

558-033 D

REMOVABLE FRONT TOW

HOOKS STORED ON THE

F 25

D CHASSIS FRAME

574-001 D

BUMPER MOUNTING FOR

SINGLE LICENSE PLATE

642-998 D

NO BUMPER/FENDER

MOUNTED SIGHT RODS

585-998 D NO MUDFLAP BRACKETS

590-998 D NO REAR MUDFLAPS

586-024 D

FENDER AND FRONT OF HOOD

MOUNTED FRONT M

D UDFLAPS

576-998 D NO TIRE CHAINS/HANGER

551-007 D

GRADE 8 THREADED HEX

HEADED FRAME FASTEN

D ERS

583-998 D NO REAR QUARTER FENDERS

600-998 D NO CAB GUARD

604-998 D NO TIRE CARRIER

489-998 D

NO TIRE PRESSURE

CONTROL/SENSOR

794-998 D

NO JACK OR WHEEL WRENCH

PROVISION

795-998 D NO TOOLS

605-998 D

CHASSIS,MISC CUSTOM

REQUIREMENTS-NONE

601-998 D NO BODY BUILDER DIAGRAMS

970-998 D NO BODY TYPE

FIFTH WHEEL & EQUIPMENT

578-998 D NO FIFTH WHEEL

577-998 D NO FIFTH WHEEL LOCATION

580-998 D

NO ADDITIONAL FIFTH WHEEL

DRILLINGS

582-998 D NO FIFTH WHEEL LEG HEIGHT

570-998 D NO FIFTH WHEEL MOUNTING

890-998 D NO FIFTH WHEEL PLUMBING

579-998 D

NO FIFTH WHEEL

RELEASE/INST.

591-998 D NO FIFTH WHEEL ADD-ONS

FUEL TANK(S) & EQUIPMENT

206-998 D NO RH FUEL TANK

201-998 D NO RH AUXILIARY FUEL TANK

204-156 D

100 GALLON/378 LITER

ALUMINUM FUEL TANK

F 20

D - LH

200-998 D NO LH AUXILIARY FUEL TANK

230-998 D NO BETWEEN RAIL FUEL TANK

203-998 D NO HYDRAULIC OIL TANK

218-001 D

23 INCH DIAMETER FUEL

TANK(S)

215-005 D

PLAIN ALUMINUM/PAINTED

STEEL FUEL/HYDRAU

LIC TANK(S) WITH PAINTED

BANDS

212-007 D FUEL TANK(S) FORWARD

11F-998 D

NO NATURAL GAS VEHICLE

FUEL TANK VENT LI

D NE/STACK

231-998 D

NO FUEL TANK MTG BETWEEN

RAILS

232-998 D

NO ADDITIONAL FUEL

PROVIDED

664-001 D PLAIN STEP FINISH

207-998 D NO FUEL TANK SCREENS

205-001 D FUEL TANK CAP(S)

220-998 D NO FUEL HEATER

122-1H2 D

DETROIT FUEL/WATER

SEPARATOR WITH BYPASS

F 10

D AND 12 VOLT PREHEATER

216-020 D

EQUIFLO INBOARD FUEL

SYSTEM

20E-998 D

NO AUXILIARY FUEL SUPPLY

AND RETURN PORT

D S

202-016 D

HIGH TEMPERATURE

REINFORCED NYLON FUEL L

D INE

213-998 D NO FUEL LINE INSULATION

221-998 D NO FUEL COOLER

TIRES

093-2CC D

MICHELIN XZU-S2 315/80R22.5

20 PLY RADIA

F 100

D L FRONT TIRES

094-2BX D

MICHELIN X WORKS XDY

11R22.5 16 PLY RADI

R 176

D AL REAR TIRES

095-998 D NO PUSHER/TAG TIRES

510-998 D NO SPARE TIRE

508-998 D NO ADDITIONAL SPARE TIRE

HUBS

418-060 D

CONMET PRESET PLUS

PREMIUM IRON FRONT HU

D BS

450-060 D

CONMET PRESET PLUS

PREMIUM IRON REAR HUB

D S

449-998 D NO PUSHER OR TAG HUBS

WHEELS

502-433 D

ACCURIDE 29039 22.5X9.00 10-

HUB PILOT 5.

F 66

D

25 INSET 5-HAND STEEL DISC

FRONT WHEELS

505-428 D

ACCURIDE 28828 22.5X8.25 10-

HUB PILOT 2-

R 104

D

HAND HD STEEL DISC REAR

WHEELS

509-998 D NO PUSHER/TAG DISC WHEELS

511-998 D NO SPARE WHEEL

51A-998 D

NO ADDITIONAL SPARE

WHEEL

50T-998 D

NO FRONT AXLE WHEEL/HUB

50U-998 D

NO REAR AXLE WHEEL/HUB

524-998 D

NO POLISHED, BRIGHT

STANDARD POLISH, CLE

AN BUFF OR BRUSHED FINISH

FRONT WHEELS

525-998 D

REAR WHEELS

526-998 D

PUSHER/TAG WHE

D ELS

52L-998 D

SPARE WHEEL

50W-998 D

NO RIM/WHEEL TIRE

PRESSURE SENSOR

496-011 D

FRONT WHEEL MOUNTING

NUTS

497-011 D

REAR WHEEL MOUNTING

NUTS

498-998 D

NO TIRE VALVE

STEM/CAP/EXTENSIONS

CAB EXTERIOR

829-072 D

112 INCH BBC FLAT ROOF

ALUMINUM CONVENTI

D ONAL CAB

682-998 D NO SLEEPER BOX/SLEEPERCAB

784-998 D NO AIR SHIELD OR BRACKETS

783-998 D NO SIDE EXTENDERS

782-998 D NO FRAME SIDE FAIRINGS

650-008 D AIR CAB MOUNTING

705-998 D

NO MISCELLANEOUS CUSTOM

CAB REQUIREMENTS

648-998 D NO RADIATOR GRILLE SCREEN

754-017 D

BOLT-ON MOLDED FLEXIBLE

FENDER EXTENSION

F 10

D S

678-001 D LH AND RH GRAB HANDLES

646-009 D PAINTED PLASTIC GRILLE

65X-001 D

ARGENT SILVER HOOD

MOUNTED AIR INTAKE GR

D ILLE

644-004 D FIBERGLASS HOOD

690-998 D

NO NOISE SHIELD-ENG

COMPARTMENT

727-1AF D

SINGLE 14 INCH ROUND

HADLEY AIR HORN UND

F 4

D ER LH DECK

726-001 D SINGLE ELECTRIC HORN

728-001 D SINGLE HORN SHIELD

657-001 D

DOOR LOCKS AND IGNITION

SWITCH KEYED THE

D SAME

78G-004 D KEY QUANTITY OF 4

575-001 D

REAR LICENSE PLATE MOUNT

END OF FRAME

327-998 D NO OTHER LIGHTS

312-043 D

INTEGRAL

HEADLIGHT/MARKER

ASSEMBLY

302-047 D

LED AERODYNAMIC MARKER

LIGHTS

315-998 D NO FOG LIGHTS

311-001 D DAYTIME RUNNING LIGHTS

316-998 D NO SPOTLIGHTS

294-1AY D

INTEGRAL LED

STOP/TAIL/BACKUP LIGHTS

300-015 D

STANDARD FRONT TURN

SIGNAL LAMPS

469-998 D NO WORK LIGHT

318-998 D

NO UTILITY/ADVERTISING

LIGHT

744-1BC D

DUAL WEST COAST BRIGHT

FINISH HEATED MIR

RORS WITH LH AND RH

REMOTE

797-001 D DOOR MOUNTED MIRRORS

796-001 D 102 INCH EQUIPMENT WIDTH

743-204 D

LH AND RH 8 INCH BRIGHT

FINISH CONVEX MI

RRORS MOUNTED UNDER

PRIMARY MIRRORS

74A-998 D NO AUXILIARY MIRROR

74B-998 D NO AUXILIARY MIRROR

713-998 D NO PERMIT PLAQUE

729-001 D

STANDARD SIDE/REAR

REFLECTORS

73A-998 D NO REFLECTIVE DEVICES

677-998 D NO CAB MOUNTED STEPS

275-998 D

NO EMERGENCY WARNING

SIRENS

764-998 D NO EXTERIOR SUN VISOR

768-043 D

63X14 INCH TINTED REAR

WINDOW

661-003 D

TINTED DOOR GLASS LH AND

RH WITH TINTED

NON-OPERATING WING

WINDOWS

654-011 D

RH AND LH ELECTRIC

POWERED WINDOWS

F 4

767-998 D NO SIDE WINDOW

769-998 D NO LOWER DOOR WINDOW

663-013 D

1-PIECE SOLAR GREEN GLASS

WINDSHIELD

659-019 D

2 GALLON WINDSHIELD

WASHER RESERVOIR WIT

HOUT FLUID LEVEL

INDICATOR, FRAME MOUNTE

D D

647-998 D NO WINTERFRONT

CAB INTERIOR

707-1AK D OPAL GRAY VINYL INTERIOR

055-998 D

NO INTERIOR CONVENIENCE

PACKAGE

706-013 D

MOLDED PLASTIC DOOR

PANEL

708-013 D

MOLDED PLASTIC DOOR

772-006 D

BLACK MATS WITH SINGLE

INSULATION

785-001 D

DASH MOUNTED ASH TRAYS

AND LIGHTER

691-008 D

FORWARD ROOF MOUNTED

CONSOLE WITH UPPER

STORAGE COMPARTMENTS

WITHOUT NETTING

694-998 D

NO INTERIOR GLOVE BOX/CAB

FLOOR STORAGE

696-998 D NO REAR FLOOR STORAGE

693-998 D NO INTERIOR DOOR STORAGE

826-998 D NO LOWER BUNK

666-998 D NO BUNK RESTRAINT

738-998 D NO CLOCK

742-007 D

(2) CUP HOLDERS LH AND RH

DASH

680-007 D GRAY/CHARCOAL WING DASH

860-004 D

SMART SWITCH EXPANSION

MODULE

716-998 D NO WINDSHIELD FAN

720-004 D

10 LB. FIRE EXTINGUISHER

WITH MOUNTING B

F 20

D RACKET

71T-998 D NO SMOKE/GAS DETECTOR

714-998 D NO FIRST AID KIT

700-002 D

HEATER, DEFROSTER AND AIR

CONDITIONER

701-001 D STANDARD HVAC DUCTING

703-005 D

MAIN HVAC CONTROLS WITH

RECIRCULATION SW

D ITCH

689-998 D NO AUXILIARY HVAC UNIT

170-015 D

STANDARD HEATER

PLUMBING

130-041 D

VALEO HEAVY DUTY A/C

REFRIGERANT COMPRES

D SOR

702-002 D BINARY CONTROL, R-134A

739-033 D STANDARD INSULATION

285-027 D

SOLID-STATE CIRCUIT

PROTECTION AND FUSES

D WITH SPARE FUSE KIT

96R-002 S

STANDARD ELECTRICAL

PROTECTIVE COATING,

GREASE ON BATTERY

TERMINALS AND RED ENAM

EL PAINT IN ENGINE

COMPARTMENT AND ON CH

S ASSIS CONNECTIONS

280-007 D

12V NEGATIVE GROUND

ELECTRICAL SYSTEM

324-011 D

DOME DOOR ACTIVATED LH

AND RH, DUAL READ

ING LIGHTS, FORWARD CAB

ROOF

655-005 D

LH AND RH ELECTRIC DOOR

LOCKS

740-998 D NO MATTRESS

284-998 D

NO POWER SUPPLY

SLEEPER/CAB

67E-998 D

NO ENTRY/ACCESS/STEP

710-998 D NO CAB PRIVACY CURTAIN

722-002 D

TRIANGULAR REFLECTORS

WITHOUT FLARES

F 10

756-1E1 D

ELITE HIGH BACK AIR

SUSPENSION DRIVER SE

F 50

D

AT WITH HEAT, 3 CHAMBER

AIR LUMBAR, INTE

GRATED CUSHION EXTENSION,

FORWARD AND RE

AR CUSHION TILT AND

ADJUSTABLE SHOCK

760-1E1 D

ELITE HIGH BACK AIR

SUSPENSION PASSENGER

F 40 R 15

D

SEAT WITH HEAT, 3 CHAMBER

AIR LUMBAR, I

NTEGRATED CUSHION

EXTENSION, FORWARD AND

REAR CUSHION TILT AND

ADJUSTABLE SHOCK

762-998 D NO REAR PASSENGER SEAT

757-998 D NO SEAT SKIRT(S)

759-998 D NO SEAT ARMREST

711-004 D

LH AND RH INTEGRAL DOOR

PANEL ARMRESTS

758-022 D

BLACK MORDURA CLOTH

DRIVER SEAT COVER

761-023 D

BLACK MORDURA CLOTH

PASSENGER SEAT COVER

755-998 D

NO REAR PASSENGER SEAT

COVERS

763-101 D BLACK SEAT BELTS

6TS-998 D

NO TELEMATICS SYSTEM -

532-002 D

ADJUSTABLE TILT AND

TELESCOPING STEERING

F 10

D COLUMN

540-015 D

4-SPOKE 18 INCH (450MM)

STEERING WHEEL

765-002 D

DRIVER AND PASSENGER

INTERIOR SUN VISORS

CONTROLS & INSTRUMENTS

870-001 D BLACK GAUGE BEZELS

732-004 D

GRAY DRIVER INSTRUMENT

734-004 D

GRAY CENTER INSTRUMENT

68J-998 D

NO SWITCH BLANK -

INSTRUMENT PANEL

486-001 D

LOW AIR PRESSURE

INDICATOR LIGHT AND AUD

D IBLE ALARM

838-998 D NO AIR APPLICATION GAUGE

840-002 D

2 INCH PRIMARY AND

SECONDARY AIR PRESSUR

D E GAUGES

198-006 D

ENGINE COMPARTMENT

MOUNTED AIR RESTRICTI

ON INDICATOR WITH

GRADUATIONS, WITH WARN

D ING LIGHT IN DASH

721-001 D 97 DB BACKUP ALARM R 3

149-017 D

ELECTRONIC CRUISE

CONTROL WITH SWITCHES

ON AUXILIARY GAUGE PANEL

(B DASH PANEL)

156-007 D

KEY OPERATED IGNITION

SWITCH AND INTEGRA

L START POSITION; 4 POSITION

OFF/RUN/STA

D RT/ACCESSORY

157-998 D NO REMOTE START

811-042 D

ICU3S, 132X48 DISPLAY WITH

DIAGNOSTICS,

28 LED WARNING LAMPS AND

DATA LINKED

160-038 D

HEAVY DUTY ONBOARD

DIAGNOSTICS INTERFACE

CONNECTOR LOCATED BELOW

LH DASH

844-001 D 2 INCH ELECTRIC FUEL GAUGE

845-011 D

FUEL FILTER RESTRICTION

INDICATOR

148-085 D

EMISSIONS LIMITED IDLE

ADJUST

163-998 D

NO ENGINE OPT/RPM

CONTROLS WIRING

87L-998 D

NO REMOTE ENGINE

CONTROL-ENABLE

33U-998 D

NO CUSTOMER DEFINED

WIRING FUNCTION

866-998 D

NO AXLE TEMPERATURE

GAUGE

856-001 D

ELECTRICAL ENGINE

COOLANT TEMPERATURE GA

D UGE

854-998 D

NO ENGINE OIL TEMPERATURE

GAUGE

864-001 D

2 INCH TRANSMISSION OIL

TEMPERATURE GAUG

D E

867-998 D

NO OUTSIDE AIR

TEMPERATURE GAUGE

830-017 D

ENGINE AND TRIP HOUR

METERS INTEGRAL WIT

D HIN DRIVER DISPLAY

438-998 D NO HUBODOMETER

33A-998 D

NO WARNING LIGHT

SWITCHES

372-063 D

(1) DASH MOUNTED PTO

SWITCH WITH INDICAT

F 10

D

OR LAMP FOR CUSTOMER

INSTALLED PTO

736-998 D

NO OBSTACLE DETECTION

73H-998 D

NO CAMERA/VIDEO/IMAGING

49B-998 D

NO VEHICLE STABILITY

ADVISOR OR CONTROL

73B-998 D

NO LANE DEPARTURE

WARNING SYSTEM

852-002 D

ELECTRIC ENGINE OIL

PRESSURE GAUGE

679-001 D

OVERHEAD INSTRUMENT

35M-998 D

NO WRG-BDY MULTIPLEX

EXPNSN UNIT

786-998 D

NO POSITIONING/LOCATING

78A-998 D

NO

POSITION/COMMUNICATION

ACCESSORY

1U1-998 D NO NAVIGATION SYSTEM

746-116 D

AM/FM/WB WORLD TUNER

RADIO WITH SIRIUSXM

F 10

D

, CD PLAYER, BLUETOOTH,

IPOD INTERFACE A

ND USB AND AUXILIARY

INPUTS, J1939

747-001 D DASH MOUNTED RADIO

74D-998 D NO RADIO/SPEAKER WIRING

750-002 D (2) RADIO SPEAKERS IN CAB

753-001 D

AM/FM ANTENNA MOUNTED

ON FORWARD LH ROOF

748-006 D

POWER AND GROUND WIRING

PROVISION OVERHE

D AD

749-016 D

CB WIRING ONLY TO

ROOF/OVERHEAD CONSOLE;

D NO MOUNTING PROVISION

752-998 D

NO CB ANTENNA, BRACKET

OR LEAD

78C-003 D

INTEROPERABLE SDAR

ANTENNA

810-027 D

ELECTRONIC MPH

SPEEDOMETER WITH

SECONDAR

Y KPH SCALE, WITHOUT

ODOMETER

817-001 D

STANDARD VEHICLE SPEED

SENSOR

812-001 D

ELECTRONIC 3000 RPM

TACHOMETER

813-1B4 D

VT-HU CONNECTIVITY

PLATFORM HARDWARE

8D1-002 D

2 YEARS DETROIT CONNECT

BASE PACKAGE (VI

RTUAL TECHNICIAN, DETROIT

CONNECT PORTAL

ACCESS)FOR VT-HU

CONNECTIVITY PLATFORM

8Z1-998 D

NO ZONAR SERVICES

SELECTED

80K-998 D NO SHUTDOWN OVERRIDE

80L-998 D

NO REGEN SYSTEM

TAILORING

80M-998 S NO ALTERNATE PTO SPEED

80N-998 D

NO REDUCED ENGINE SPEED

ON VSS FAILURE

80P-998 S

NO FLEET SPEC FOR

PARAMETERIZATION

80Q-998 S

NO VEHICLE SPEED LIMIT -

GHG

162-002 D

IGNITION SWITCH

CONTROLLED ENGINE STOP

885-998 D NO CONTROLS-FIRE PUMP

329-010 D

TWO ON/OFF ROCKER

SWITCHES IN THE DASH W

ITH INDICATOR LIGHTS AND

WIRE ROUTED TO

CHASSIS AT BACK OF CAB,

LABEL OPT

81Y-998 D NO PRE TRIP SYSTEM TEST

44R-998 D

NO ON/OFF LATCHING

SMARTPLEX SWITCH

44S-998 D

NO ON/OFF MOMENTARY

44T-998 D

NO ON/OFF/ON LATCHING

44U-998 D

NO ON/OFF/ON MOMENTARY

44V-998 D

NO PRE-DEFINED SMARTPLEX

INDICATOR LAMPS

44W-998 D

NO UNDEFINED INDICATOR

LAMPS

264-998 D

NO CONTROLS-SIREN/AIR

HORN

482-001 D

BW TRACTOR PROTECTION

VALVE

883-001 D

TRAILER HAND CONTROL

BRAKE VALVE

836-015 D

DIGITAL VOLTAGE DISPLAY

INTEGRAL WITH DR

D IVER DISPLAY

660-008 D

SINGLE ELECTRIC

WINDSHIELD WIPER MOTOR W

D ITH DELAY

304-001 D

MARKER LIGHT SWITCH

INTEGRAL WITH HEADLI

D GHT SWITCH

27D-998 D

NO ALTERNATING FLASHING

HEADLAMP SYSTEM

882-004 D

TWO VALVE PARKING BRAKE

SYSTEM WITH WARN

D ING INDICATOR

299-013 D

SELF CANCELING TURN

SIGNAL SWITCH WITH D

IMMER, WASHER/WIPER AND

HAZARD IN HANDLE

298-048 D

INTEGRAL ELECTRONIC TURN

SIGNAL FLASHER

WITH STOP LAMPS

OVERRIDING HAZARD LAMPS

869-998 D NO MISCELLANEOUS GAUGES

PAINT

065-000 D PAINT: ONE SOLID COLOR

980-5F6 D CAB COLOR A: L0006EY

D WHITE ELITE EY

986-020 D

BLACK, HIGH SOLIDS

POLYURETHANE CHASSIS

D PAINT

98K-998 D

NO FUEL TANK CABINET

962-3F6 D FRONT WHEEL PAINT: N0006EA

D WHITE ELITE SS

966-3F6 D REAR WHEEL PAINT: N0006EA

D WHITE ELITE SS

96E-998 D NO PUSHER/TAG WHEEL PAINT

96F-998 D NO SPARE WHEEL PAINT

964-6Z7 D BUMPER PAINT: FP24812

D ARGENT SILVER DUPONT FLEX

976-998 D

NO EXTERIOR SUNVISOR

963-003 D

STANDARD E

COAT/UNDERCOATING

ADDITIONAL SPECIFICATIONS

99A-001 H

ENGLISH LANGUAGE

MAINTENANCE MANUAL IN E

H ACH TRUCK

ONE EXTRA SET (PSM) OF

PARTS, SERVICE, A

ND MAINTENCE MANUALS

998-033 H

CORPORATE PDI CENTER IN-

SERVICE AND OPTI

H

ON

INSTALLATION/MODIFICATION

BLM BASE SPEC. CUSTOMER

WILL INSTALL THE

IR OWN DUMP BODY. NEEDS

CHASSIS WITH MAX

IMUM GROUND CLEARANCE.

NO PUSHER AXLE.

95M-998 D

NO CUSTOMER FURNISHED

MATERIAL SPECIFIED

958-998 D NO INSPECTION-LABOR ONLY

99B-006 D

SHIP TO CLEVELAND PDI

CENTER FOR MODIFIC

D ATIONS PRIOR TO DELIVERY

82N-998 D NO SHIPPING PROTECTION

999-069 D

DLR/CUST ADVISED&ACCEPTS

POTENTIAL INTER

FERENCE BTWN FRONT TIRE &

WASHER BOTTLE

996-001 D

U.S. FMVSS CERTIFICATION,

EXCEPT SALES C

D ABS AND GLIDER KITS

MWF-003 S

DETROIT FRONT AXLE

COVERAGE, VOCATIONAL,

3 YEAR/300,000 MILES/480 000

KILOMETERS

PROVISIONS

FAR 52.252-1 Solicitation Provisions Incorporated By Reference (FEB 1998)

This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address(es): [Insert one or more Internet addresses]:

FAR Clauses - https://www.acquisition.gov/far/

DOI Clauses - http://www.doi.gov/pam/programs/acquisition/diapr.cfm

FAR 52.212-3 Offeror Representations and Certifications-Commercial Items (Mar 2020)

The Offeror shall complete only paragraph (b) of this provision if the Offeror has completed the annual representations and certification electronically in the System for Award Management

(SAM) accessed through https://www.sam.gov. If the Offeror has not completed the annual

NUMBER PROVISION TITLE DATE

DIAR 1452.215-71

Use and Disclosure of Proposal Information – Department of the Interior

Apr 1984

DIAR 1452.233-2 Service of Protest Pursuant to 1433.106 Jul 1996

FAR 52.204-7 System for Award Management Oct 2018

FAR 52.204-16 Commercial and Government Entity Code Reporting Jul 2016

FAR 52.204-22 Alternative Line Item Proposal Jan 2017

FAR 52.212-1 Instructions to Offerors-Commercial Items Mar 2020 https://www.acquisition.gov/far/ http://www.doi.gov/pam/programs/acquisition/diapr.cfm https://www.sam.gov/ representations and certifications electronically, the Offeror shall complete only paragraphs (c) through (v)) of this provision.

(a) Definitions. As used in this provision—

“Covered telecommunications equipment or services” has the meaning provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video

Surveillance Services or Equipment.

Economically disadvantaged women-owned small business (EDWOSB) concern means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States and who are economically disadvantaged in accordance with 13

CFR part 127. It automatically qualifies as a women-owned small business eligible under the

WOSB Program.

Forced or indentured child labor means all work or service—

(1) Exacted from any person under the age of 18 under the menace of any penalty for its nonperformance and for which the worker does not offer himself voluntarily; or

(2) Performed by any person under the age of 18 pursuant to a contract the enforcement of which can be accomplished by process or penalties.

Highest-level owner means the entity that owns or controls an immediate owner of the offeror, or that owns or controls one or more entities that control an immediate owner of the offeror. No entity owns or exercises control of the highest level owner.

Immediate owner means an entity, other than the offeror, that has direct control of the offeror. Indicators of control include, but are not limited to, one or more of the following:

ownership or interlocking management, identity of interests among family members, shared facilities and equipment, and the common use of employees.

Inverted domestic corporation, means a foreign incorporated entity that meets the definition of an inverted domestic corporation under 6 U.S.C. 395(b), applied in accordance with the rules and definitions of 6 U.S.C. 395(c).

https://www.acquisition.gov/content/part-52-solicitation-provisions-and-contract-clauses#unique_37607080 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title6-section395&num=0&edition=prelim http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title6-section395&num=0&edition=prelim

Manufactured end product means any end product in product and service codes (PSCs)

1000-9999, except—

(1) PSC 5510, Lumber and Related Basic Wood Materials;

(2) Product or Service Group (PSG) 87, Agricultural Supplies;

(3) PSG 88, Live Animals;

(4) PSG 89, Subsistence;

(5) PSC 9410, Crude Grades of Plant Materials;

(6) PSC 9430, Miscellaneous Crude Animal Products, Inedible;

(7) PSC 9440, Miscellaneous Crude Agricultural and Forestry Products;

(8) PSC 9610, Ores;

(9) PSC 9620, Minerals, Natural and…