A06_Specifications_Updated260127_Redacted_0002.pdf

AMENDMENT 2 140FGA26Q0004

Salient Characteristics – Small Articulated Loader (Bobcat L28 or Equal)

Note: This is not a brand name requirement; however, a Bobcat L28 is an example of a machine meeting our requirements. You must offer this exact machine or an equivalent meeting or exceeding it in accordance with FAR 52.211-6 (Brand Name or Equal).

Non-Manufacturer Rule Waiver This product is included on the SBA’s Non-Manufacturer Rule (NMR) Class Waiver list. Small business concerns may supply the product without being the manufacturer, in accordance with the waiver provisions.

A. Product Features.

The offered product must meet or exceed the following minimum characteristics to be considered technically acceptable:

1. Engine:

o Minimum 24.8 HP Tier 4 diesel engine.

2. Lift Capability:

o Rated operating capacity (ISO) of at least 1,200 lbs articulated and 1,500 lbs straight.

o Telescopic lift arm providing minimum 24-inch extension.

o Maximum hinge pin height (extended) of at least 104 inches.

3. Hydraulic System:

o Auxiliary hydraulic flow of minimum 9 GPM to maximum 19 GPM.

o System relief pressure of approximately 2,900 psi.

4. Dimensions & Maneuverability:

o Overall width not to exceed 50 inches (over tires ≤ 46.5 inches).

o Inside turning radius of ≤ 80 inches for tight maneuverability.

o Ground clearance of ≥ 5 inches.

5. Traction & Drive:

o Four-wheel drive or equivalent hydrostatic system with individual wheel motors.

o Minimum 8 ply turf tires.

6. Safety & Operator Protection:

o ROPS compliant with ISO 3471 and FOPS compliant with ISO 3449 Level I.

o Integrated operator interlock system.

o Backup alarm and horn.

o Enclosed heated cab suitable for winter operations.

o Cab shall include windshield wiper and washer fluid system for front windshield to maintain visibility in snow, ice, and wet conditions.

7. Lighting & Visibility:

o LED work lights (front and rear).

8. Attachment Interface:

o Quick-attach system compatible with standard loader attachments (e.g., Bob- Tach or equivalent).

9. Instrumentation:

o Gauges for engine temperature, fuel level, hour meter, RPM, and warning indicators.

10. Warranty:

o Minimum 1-year full machine warranty.

11. Attachments:

Provide an angle broom attachment approximately 52 inches wide that is fully compatible with the equipment or solution you are proposing. Include all necessary installation accessories, hydraulic components, and control kits required for proper operation.

B. Delivery

A. Prices quoted must be FOB Destination

“F.o.b. destination” means --Free of expense to the Government delivered, on board the carrier’s conveyance, at a specified delivery point where the consignee’s facility (plant, warehouse, store, lot, or other location to which shipment can be made) is located; and

Supplies shall be delivered to the destination consignee’s wharf (if destination is a port city and supplies are for export), warehouse unloading platform, or receiving dock, at the expense of the contractor. The Government shall not be liable for any delivery, storage, demurrage, accessorial, or other charges involved before the actual delivery (or “constructive placement” as defined in carrier tariffs) of the supplies to the destination, unless such charges are caused by an act or order of the Government acting in its contractual capacity. If rail carrier is used, supplies shall be delivered to the specified unloading platform of the consignee. If motor carrier (including “piggyback”) is used, supplies shall be delivered to truck tailgate at the unloading platform of the consignee, except when the supplies delivered meet the requirements of Item 568 of the National Motor Freight Classification for “heavy or bulky freight.” When supplies meeting the requirements of the referenced Item 568 are delivered, unloading (including movement to the tailgate) shall be performed by the consignee, with assistance from the truck driver, if requested. If the contractor uses rail carrier or freight forwarder for less than carload shipments, the contractor shall ensure that the carrier will furnish tailgate delivery when required, if transfer to truck is required to complete delivery to consignee.

Contractor responsibilities. The contractor shall -- (1)(i) Pack and mark the shipment to comply with contract specifications; or

(ii) In the absence of specifications, prepare the shipment in conformance with carrier requirements;

(2) Prepare and distribute commercial bills of lading;

(3) Deliver the shipment in good order and condition to the point of delivery specified in the contract;

(4) Be responsible for any loss of and/or damage to the goods occurring before receipt of the shipment by the consignee at the delivery point specified in the contract;

(5) Furnish a delivery schedule and designate the mode of delivering carrier; and

(6) Pay and bear all charges to the specified point of delivery.

B. Credit for Trade-in: 2002 John Deere 1435

C. Delivery Location:

Product shall be delivered to the following location:

DC Booth National Fish Hatchery 423 Hatchery Circle Spearfish, SD 57783

D. Installation:

Prices quoted must include installation. All labor and parts associated with and required for installation are the sole responsibility of the contractor. No assistance or equipment will be provided by the government. Installation shall be completed according to industry standards.

E. Technical Point of Contact (POC):

F. Delivery Instructions:

No later than three days prior to delivery, please contact the Points of Contact listed above, to arrange a specific time for delivery. Unloading the product is the sole responsibility of the delivery carrier. No labor or equipment will be provided by the government to unload the supplies.

G. Customer Specific Delivery requirements: Not applicable

H. Installation:

Prices quoted must include installation. All labor and parts associated with and required for installation are the sole responsibility of the contractor. No assistance or equipment will be provided by the government. Installation shall be completed according to industry standards.