13371_-_Drawings_with_Issue_Date.pdf

PDF 2 MB Posted Aug 28, 2026

Attached to: PROJECT NUMBER: 13371; RIVERSIDE LAB FIRE ALARM REPLACEMENT DEPARTMENT OF JUSTICE RIVERSIDE FORENSIC LABORATORY RIVERSIDE, RIVERSIDE COUNTY, CALIFORNIA CONTRACT NUMBER: 26-327801
Solicitation number: 0000040211
Issued by: Riverside County, California

About this file

Written by GovTribe AI · Aug 31, 2026

This is a set of approved fire alarm system design drawings and construction documents prepared for the California Department of General Services (DGS) on behalf of the Department of Justice for the Riverside Forensic Laboratory located at 7425 Mission Boulevard, Riverside, California 92509. The project involves the removal and replacement of the existing fire alarm system, including all devices and the fire alarm control unit, at the 39,122-square-foot building constructed in 1999. The scope includes installation of a fully automatic, addressable fire alarm system complying with 2025 California Building Code standards, NFPA 72 requirements, and State Fire Marshal regulations. The project is identified under OSFM Permit Number 25-S-3867-FA and JCCA Project Number 24690-2, with drawings issued on July 16, 2026. Construction is phased across multiple areas including office spaces, evidence storage, controlled substance areas, laboratory sections, and common areas, with maximum working time of two weeks per secured area. The existing fire alarm system must remain operational until the new system is approved and tested; otherwise, a 24-hour trained fire watch must be maintained at the contractor's expense. All testing and inspections require a minimum of 72 hours' notice to the State Fire Marshal.

The contractor must be a qualified firm with recent relevant experience on similar-scale projects and is responsible for investigating and providing an abatement plan for hazardous materials including asbestos and lead. Detailed shop drawing submittals must be prepared by a California-licensed specialty engineer and submitted to the Office of the State Fire Marshal for approval prior to installation. Key requirements include compliance with fire safety during construction per Chapter 33 of the 2025 California Fire Code, proper conduit routing in 3/4-inch EMT with specified wire gauges, synchronization of strobe devices, installation of end-of-line resistors, and fire-rated penetration protection throughout the building. The project involves coordination with Department of Justice personnel, continuous security escort requirements for contractors working in secured areas, special protective equipment and protocols for biological and controlled substance areas, and comprehensive testing and commissioning with state representatives present. Upon completion, a Record of Completion and Certificate of Compliance must be provided to the Department of Justice, with the existing fire alarm system demolished only after the occupancy certificate is issued.

View the file

Other files

File	Type	Posted
13371_-_Bid_Package_Documents.pdf	PDF	Aug 28, 2026
13371_-_Project_Manual_R2.pdf	PDF	Aug 28, 2026

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

T0.1

TITLE SHEET

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

T0 .1

.d w g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

LOCATION PLAN VICINITY MAP SCOPE OF WORK

7425 MISSION BLVD, RIVERSIDE, CALIFORNIA 92509

DEPARTMENT OF JUSTICE - RIVERSIDE

DEPARTMENT OF JUSTICE

1. CONTRACTOR SHALL COMPLY WITH THE REQUIREMENTS OF CHAPTER 33 - FIRE SAFETY

DURING CONSTRUCTION OF THE 2025 CALIFORNIA FIRE CODE.

FIRE SAFETY DURING CONSTRUCTION

1. REMOVAL AND REPLACEMENT OF FIRE ALARM SYSTEM, INCLUDING DEVICES AND FIRE ALARM

CONTROL UNIT.

RIVERSIDE LAB FIRE ALARM REPLACEMENT

RIVERSIDE FORENSIC LABORATORY

BUILDING SUBMITTAL - PRIMARY OSFM PERMIT NUMBER: 25-S-3867-FA

PROJECT INFORMATION

PREPARED FOR:

DEPARTMENT OF JUSTICE - RIVERSIDE

7425 MISSION BLVD,

RIVERSIDE, CA 92509

LENA VANCE, ABMA

DEPARTMENT OF JUSTICE

PHONE : (916) 210-7106

SABINA WILEY / PROJECT DIRECTOR II

PHONE : (279) 799-3936

PREPARED BY:

J.C. CHANG & ASSOCIATES, INC.

ENGINEERS, ARCHITECTS AND PLANNERS

385 VAN NESS AVENUE, SUITE 208

TORRANCE, CALIFORNIA 90501

PHONE : (310) 212-7644

ARCHITECT OF RECORD /

PRIMARY PROFESSIONAL

MYOUNGJIN KANG

NO. C-37614

385 VAN NESS AVE. #208

TORRANCE, CALIFORNIA 90501

ENGINEER OF RECORD /

PRIMARY PROFESSIONAL

SEVAG AVANESSIAN

NO. E-22793

385 VAN NESS AVE. #208

TORRANCE, CALIFORNIA 90501

APPLICABLE CODES AND STANDARDS

1. 2025 BUILDING STANDARDS ADMINISTRATIVE CODE, PART 1, TITLE 24 C.C.R.

2. 2025 CALIFORNIA BUILDING CODE (CBC), PART 2, TITLE 24 C.C.R.

(2024 INTERNATIONAL BUILDING CODE & 2024 CALIFORNIA AMENDMENTS)

3. 2025 CALIFORNIA ELECTRICAL CODE (CEC), PART 3, TITLE 24 C.C.R.

(2023 NATIONAL ELECTRICAL CODE AND 2024 CALIFORNIA AMENDMENTS)

4. 2025 CALIFORNIA MECHANICAL CODE (CMC), PART 4, TITLE 24 C.C.R.

(2024 UNIFORM MECHANICAL CODE AND 2024 CALIFORNIA AMENDMENTS)

5. 2025 CALIFORNIA ENERGY CODE (CEC), PART 6, TITLE 24 C.C.R.

6. 2025 CALIFORNIA FIRE CODE, PART 9, TITLE 24 C.C.R.

(2024 INTERNATIONAL FIRE CODE AND 2024 CALIFORNIA AMENDMENTS)

7. 2025 CALIFORNIA GREEN BUILDING STANDARDS CODE (CALGREEN), PART 11,

TITLE 24 C.C.R.

8. 2025 CALIFORNIA REFERENCED STANDARDS, PART 12, TITLE 24 C.C.R.

9. TITLE 19 C.C.R., PUBLIC SAFETY, STATE FIRE MARSHAL REGULATIONS.

PARTIAL LIST OF APPLICABLE STANDARDS

1. NFPA 13 AUTOMATIC SPRINKLER SYSTEMS (CA AMENDED) 2025 EDITION

2. NFPA 14 STANDPIPE SYSTEM (CA AMENDED) 2024 EDITION

3. NFPA 17a WET CHEMICAL SYSTEMS 2024 EDITION

4. NFPA 20 STATIONARY PUMPS 2025 EDITION

5. NFPA 24 PRIVATE FIRE MAINS (CA AMENDED) 2025 EDITION

6. NFPA 72 NATIONAL FIRE ALARM CODE (CA AMENDED) 2025 EDITION

7. NFPA 2001 CLEAN AGENT FIRE EXTINGUISHING SYSTEMS 2025 EDITION

W/ CA AMENDMENTS

8. NFPA 101 LIFE SAFETY CODE 2024 EDITION

9. REFERENCE CODE SECTION FOR NFPA STANDARDS 2025 CBC (SFM)

CHAPTER 35

REFERENCE CODE SECTION FOR NFPA STANDARDS ARE IN 2025 CBC CHAPTER 35 OR 2025 CFC

CHAPTER 80. SEE CHAPTER 35 FOR STATE OF CALIFORNIA AMENDMENTS TO NFPA STANDARDS.

REFERENCE: 2025 CALIFORNIA FIRE CODE

1. SEE OVERALL SITE PLAN FOR SITE ACCESS FOR BOTH PUBLIC RIGHT OF WAY AND LOCAL

FIRE DEPARTMENT.

2. TURNAROUND CAN BE ACCOMPLISHED BY USING EXISTING SITE ROADS. SEE T0.2.

FIRE APPARATUS ACCESS

1. THE CONTRACT IS RESPONSIBLE FOR INVESTIGATING HAZARDOUS MATERIAL AT THE AREA OF

WORK INCLUDING BUT NOT LIMITED TO ASBESTOS AND LEAD, AND PROVIDING A REPORT AND

ABATEMENT PLAN ACCORDING TO THE CALIFORNIA STANDARD CODE AND CALOSHA

REQUIREMENTS.

HAZMAT NOTE

1. IT IS EXPECTED THAT THE BIDDER WILL BE A QUALIFIED CONTRACTOR WITH RECENT,

RELEVANT EXPERIENCE WITH PROJECTS OF SIMILAR SIZE AND SCALE, AND UTILIZE THEIR

QUALIFICATIONS AND EXPERIENCE TO PROVIDE A COMPLETE AND ACCURATE BASE BID.

BASE BID

PROJECT AREA

A MINIMUM OF 72 HOURS NOTICE WILL BE PROVIDED TO THE STATE FIRE MARSHAL WHEN

SCHEDULING ANY TESTS OR INSPECTIONS.

STATE FIRE MARSHAL SPECIAL INSPECTIONS

DRAWING INDEX

PROJECT LOCATION

WOODCREST

RIVERSIDE

HOME GARDENS

NORCO

EASTVALE JURUPA VALLEY

HIGHGROVE

BLOOMINGTON

CORONA

COLTON

ARLINGTON SOUTH

RAMONA

SHEET NUMBER SHEET TITLE

GENERAL

T0.1 TITLE SHEET

T0.2 BUILDING INFO AND FIRE ACCESS SITE PLAN

T0.3 STATE FIRE MARSHAL TRIAGE LIST

FIRE ALARM

FA0.1 FIRE ALARM - GENERAL NOTES LEGEND

FA0.2 FIRE ALARM - SYMBOL LIST AND SEQUENCE OF OPERATION

FA0.3 FIRE ALARM DETAILS

FA0.4 FIRE ALARM DETAILS

FA0.5 FIRE ALARM DETAILS

FA0.6 FIRE ALARM - RISER DIAGRAM

FA0.7 FIRE ALARM - PHASING PLAN

FA1.1 FIRE ALARM - DEMOLITION FLOOR PLAN

FA2.1 FIRE ALARM - NEW WORK FLOOR PLAN

TOTAL NUMBER OF SHEETS = 12

ALL DEFERRED FIRE PROTECTION AND FIRE ALARM SYSTEMS SHOWN IN DOCUMENTS ESTABLISH

DESIGN INTENT, ARE SCHEMATIC AND FOR REFERENCE ONLY.

THE GENERAL CONTRACTOR IS TO PROVIDE COMPLETE DESIGN SUBMITTALS WITH JUSTIFICATION

OF LIFE SAFETY ELEMENTS AND/OR SYSTEMS. PRIOR TO SUBMITTING TO THE OFFICE OF THE

STATE FIRE MARSHAL, ALL SUBMITTALS SHALL BE AS FOLLOWS:

1. SPECIALTY (CA Licensed) ENGINEER MUST STAMP AND WET-SIGN DRAWINGS INCLUDING

SUPPORTING CALCULATIONS.

2. AFFIX SHOP DRAWING STAMP INDICATING COORDINATION BETWEEN THE DEFERRED

SUBMITTAL AND APPROVED DRAWINGS IS COMPLETE.

THE DEFERRED SUBMITTAL ITEMS SHALL NOT BE INSTALLED UNTIL THE DESIGN AND SUBMITTAL

DOCUMENTS HAVE BEEN APPROVED BY THE OFFICE OF THE STATE FIRE MARSHAL.

APPROVAL FOR THE ELEMENTS OF THE DESIGN LISTED BELOW IS DEFERRED UNDER THE

PROVISION OF 2025 CBC 107.3.4.1.

· FIRE ALARM

ARCHITECT AND/OR ENGINEER OF RECORD: AFFIX SHOP DRAWING STAMP INDICATING SUBMITTAL

HAS BEEN REVIEWED AND FOUND TO BE IN GENERAL CONFORMANCE TO THE DESIGN.

DEFERRED SUBMITTAL

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval and issuance of a permit is subject to approved construction documents and or shop drawings. All construction documents and or shop drawings shall be submitted to the SFM for final review and approval.

5/22/2026

DSA Test Mark - EPR Admin Change to "INCORPORATE"

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

5/14/2026

ISSUE DATE: JULY 16, 2026

FDC

20'-3 1/2"

'-1

25'-8 3/8"

12'-6"

26'-9 1/4"

12'-6"

40'-2 1/8" 28'-0 1/8"

'-1

T0.2

BUILDING INFO AND FIRE

ACCESS SITE PLAN

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

T0 .2

.d w g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

BUILDING INFORMATION

BUILDING NAME CONSTRUCTION

TYPE

NUMBER

OF STORIES

BUILDING

AREA

IN SQ. FT.

SEPARATED /

NONSEPARATED

SPRINKLER

COVERAGE FIRE ALARM

OTHER

PROTECTION

SYSTEM

SMOKE

CONTROL

SYSTEM

OCCUPANT

LOAD

YEAR BUILDING

CONSTRUCTED

HIGH FIRE

HAZARD

SEVERITY ZONE

SEISMIC JOINT

EMERGENCY

RESPONDER RADIO

COVERAGE

OCCUPANCY

GROUP

RIVERSIDE FORENSIC

LABORATORY 1 18'-9" 39,122

(PER 2003

AS-BUILT PLANS)

1999 NO NO YESB, H-5, S-1 II-B

BUILDING

HEIGHT

SEPARATED YES ADDRESSABLE NO NO

AREA OF

PROJECT

39,122

ALLOWABLE

STORIES

(CBC TABLE

504.4)

USE

OFFICE,

LABORATORY,

VEHICLE EXAM

BAY

ALLOWABLE

AREA

(CBC TABLE

506.2)

70,000

NFIRE ACCESS SITE PLAN

0 607.5 FEET30

1" = 30'

15SCALE:1

AREA OF WORK

SEE FA1.1, FA2.1

ENTRANCE

SECURITY GATE

FIRE HYDRANT, TYP.

FIRE DEPARTMENT

CONNECTION

FIRE TRUCK ROUTE

EXISTING PAVED

ROAD IS MIN. 20'

WIDE EXCEPT AT

EXIT SECURITY

GATES.

MISSION BLVD.

BUILDING CODE

2025 CBC

PROPERTY

LINE, TYP.

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

T0.3

STATE FIRE MARSHAL

TRIAGE LIST

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

T0 .3

.d w g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

ITEM

SUBMITTAL REQUIREMENTS SUBMITTAL RESPONSE REFERENCE

1. GENERAL

SEE FOR SPECIFIC SECTION COMMENTS NOT APPLICABLE

PROVIDE A COMPLETE PLAN REVIEW APPLICATION

SUBMIT PLANS SUFFICIENT SIZE

PROVIDE SITE ADDRESS

PROVIDE NAME OF OWNER AND OCCUPANT

IDENTIFY IF NEW CONSTRUCTION OR T.I

IDENTIFY IF NEW OR EXISTING TENANT SPACE

IDENTIFY IF DEFERRED SUBMITTAL

ADD OSFM FILE NUMBER TO TITLE SHEET

PROJECT IS A PHASED SUBMITTAL

SLIP SHEETS SHALL BE BOUND TO SET

SHEET INDEX

WET STAMP AND SIGN SHEETS

ELECTRONIC SIGNATURE APPROVAL REQUIRED

SCOPE OF WORK

PROVIDE A KEY PLAN COORDINATED TO EACH SHEET

IDENTIFY DEFERRED SUBMITTALS

PROVIDE ADOPTED CODE CYCLE LISTINGS AND STANDARDS

PROVIDE A LEGIBLE SCALE. TYPICALLY 1/8"

PROVIDED WITH SUBMITTAL

FLOOR PLANS ARE 1/8" = 1'-0"

7425 MISSION BLVD, RIVERSIDE, CALIFORNIA 92509

DEPARTMENT OF JUSTICE

T.I.

EXISTING

ALL RELEVANT

SHEETS

T0.1

OSFM NO. NOTED ON THE TITLE SHEET (25-S-3867-FA)

PROJECT IS NOT PHASED

NOT APPLICABLE

SHEET INDEX IS ON T0.1 T0.1

ELECTRONIC SIGNATURE PROVIDED ON DOCUMENT ALL SHEETS

SCOPE OF WORK IS INCLUDED ON TITLE SHEET T0.1

N/A

N/A -

ADOPTED CODE CYCLE LISTINGS ARE INCLUDED ON TITLE SHEET

FLOOR PLANS ARE 1/8" SCALE.

T0.1

ITEM SUBMITTAL REQUIREMENTS SUBMITTAL RESPONSE REFERENCE

2. ACCESS AND WATER SUPPLY

PROVIDE LOCAL FIRE AUTHORITY APPROVAL LETTER

FIRE DEPARTMENT ACCESS

FIRE DEPARTMENT CONNECTION

FIRE HYDRANTS

FIRE ALARM ANNUNCIATOR

FIRE ALARM CONTROL PANEL

KNOX BOX/KEY SWITCH

ELEVATOR GURNEY ACCOMODATION

PROVIDE A COMPLETE FIRE ACCESS PLAN

OTHER

ALL RELEVANT

SHEETS

ELECTRONIC DOCUMENT SIGNATURE APPROVAL LETTER ATTACHED LETTER

SHOWN ON FIRE ACCESS SITE PLAN

T0.2

SHOWN ON FIRE ALARM - NEW WORK FLOOR PLAN

N/A

ALL BUILDINGS ARE FIRE TRUCK ACCESSIBLE USING EXISTING ROADS

N/A

T0.2

FA2.1

T0.2

SHOWN ON FIRE ACCESS SITE PLAN

SHOWN ON FIRE ACCESS SITE PLAN, NORTH PARKING AREA

N/A

T0.3SEE LETTER ATTACHED.

T0.1

SHOWN ON FIRE ALARM - NEW WORK FLOOR PLAN

N/A

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

FA0.1

FIRE ALARM - GENERAL

NOTES LEGEND

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

dw g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

SHOP DRAWING SPECIFICATIONS

1. NEW FIRE ALARM SYSTEM SHALL BE FULLY AUTOMATIC, ADDRESSABLE

SYSTEM PER SPECIFICATION SECTION 284621.11 "ADDRESSABLE FIRE

ALARM SYSTEMS", INCLUDING BUT NOT LIMITED TO WIRING/CONDUITS

AND DEVICES REQUIRED FOR SATISFACTORY SYSTEM OPERATION.

2. A STAMPED SET OF APPROVED FIRE ALARM DRAWINGS SHALL BE ON THE

JOB SITE AND USED FOR INSTALLATION. ANY DEVIATION FROM THE

APPROVED PLANS, INCLUDING THE SUBSTITUTION OF DEVICES, SHALL BE

APPROVED BY DEPARTMENT OF JUSTICE.

3. ALL DEVICES OF THE FIRE ALARM SYSTEM SHALL BE APPROVED AND

LISTED BY DEPARTMENT OF JUSTICE.

4. THE FIRE ALARM SYSTEM SHALL CONFORM TO THE LATEST VERSION OF

NFPA 72 (AMENDMENT), IFC FIRE CODE, IBC INTERNATIONAL BUILDING

CODE, AND 2010 AMERICAN WITH DISABILITY ACT (ADA) REQUIREMENTS.

5. THE EXISTING FIRE ALARM SYSTEM SHALL REMAIN IN OPERATION,

UNIMPAIRED, UNTIL THE NEW SYSTEM IS APPROVED AND TESTED TO ALL

NFPA STANDARDS, OTHERWISE HUMAN 24-HOURS TRAINED FIRE WATCH

SHALL BE PROVIDED AT CONTRACTOR'S EXPENSE PER 2024 IFC 403.11.1.

PRIOR TO ANY FIRE WATCH, A FORMAL WRITTEN REQUEST TO THE

DEPARTMENT OF JUSTICE SHALL BE SUBMITTED, REVIEWED AND

APPROVED BY THE DEPARTMENT OF JUSTICE IN WRITING.

6. WHEN ALL FIRE ALARM DEVICES ARE INSTALLED AND PROGRAMMING IS

COMPLETED, FIRE ALARM DEVICE MAP IN THE COMMAND CENTER

SHOULD BE UPDATED/OR PROVIDED TO INDICATE TO FACILITY

PERSONNEL THE LOCATIONS OF THE NEW DEVICES.

7. UPON COMPLETION OF THE INSTALLATION OF THE FIRE ALARM SYSTEM,

A SATISFACTORY TEST OF THE ENTIRE SYSTEM SHALL BE MADE IN THE

PRESENCE OF THE DEPARTMENT OF JUSTICE, THE STATE'S

REPRESENTATIVE AND OTHER AUTHORITIES HAVING JURISDICTION. A

MINIMUM OF 72 HOURS SHALL BE REQUIRED FOR ANY TESTING AND/OR

INSPECTION.

8. BEFORE REQUESTING FINAL APPROVAL OF THE INSTALLATION, THE

INSTALLING CONTRACTOR SHALL FURNISH A WRITTEN STATEMENT TO

THE DEPARTMENT OF JUSTICE REPRESENTATIVE TO THE EFFECT THAT

THE SYSTEM HAS BEEN INSTALLED IN ACCORDANCE WITH THE

APPROVED PLANS AND COMPLETELY TESTED IN ACCORDANCE WITH

MANUFACTURER'S SPECIFICATIONS AND APPROPRIATE NFPA

REQUIREMENTS. (2025 NFPA 72 SECTION 7.5.2).

9. A RECORD OF COMPLETION SHALL BE PREPARED BY THE INSTALLER AND

GIVEN TO THE DEPARTMENT OF JUSTICE UPON COMPLETION OF

INSTALLATION, AS PER 2025 NFPA 72 7.5.6.

10. THE TERM "PROVIDE" MEANS THAT THE CONTRACTOR SHALL FURNISH,

INSTALL, ADJUST, TEST & INTEGRATE INTO A COMPLETE SYSTEM THE

ITEM INDICATED, INCLUDING ALL HARDWARE, WIRING, AND

MISCELLANEOUS ITEMS.

11. LOCATION OF FIRE ALARM DEVICES AND EQUIPMENT ON DRAWING IS

APPROXIMATE, UNLESS DIMENSION ARE INDICATED. LOCATION OF

DEVICES AND EQUIPMENT SHALL CONFORM TO ARCHITECTURAL

FEATURES OF THE BUILDING AND OTHER WORK ALREADY IN PLACE, AND

MUST BE ASCERTAINED IN THE FIELD BEFORE THE START OF WORK.

CONDUIT AND/OR WIREMOLD RUNS AND JUNCTION AND/OR WIREMOLD

BOXES LOCATION ON DRAWINGS SHOWN DIAGRAMMATICALLY. EXACT

LOCATION AND ROUTING SHALL BE DETERMINATED BY THE CONTRACTOR

IN THE FIELD TO SUIT FIELD CONDITIONS. DO NOT SCALE DRAWINGS TO

DETERMINE LOCATIONS AND ROUTING OF CONDUITS/WIREMOLDS AND

JUNCTION/WIREMOLDS BOXES. DRAWINGS GENERALLY INDICATE WORK

TO BE PROVIDED, BUT DO NOT INDICATE ALL BENDS, TRANSITIONS OR

SPECIALS FITTINGS REQUIRED TO CLEAR BEAMS, GIRDERS OR OTHER

WORK ALREADY IN PLACE. INVESTIGATE CONDITIONS WHERE

CONDUITS/WIREMOLDS ARE TO BE INSTALLED, AND FURNISH AND

INSTALL REQUIRED FITTINGS.

12. "LABEL DESCRIPTIONS" INDICATING DEVICE TYPE AND LOCATION THAT

ARE DISPLAYED ON THE FIRE ALARM LCD DISPLAY SHOULD BE CLEAR

AND EASILY UNDERSTOOD BY THE OFFICE STAFF. DESCRIPTIONS

SHOULD BE BASED ON THE STAFFS UNDERSTANDING OF THE SITE AND

NOT ON INFORMATION TAKEN FROM PRINTS.

13. THE FIRE ALARM SYSTEM SHALL CONTAIN ALL PRINTED CIRCUIT BOARDS,

MODULES, OR OTHER EQUIPMENT TO SUPPORT THE OPERATION OF A

SYSTEM PRINTER.

14. END-OF-LINE RESISTORS SHALL BE MOUNTED AT LAST DEVICE. FIRE

ALARM DEVICES THAT HAVE END-OF-LINE RESISTOR INSTALLED IN THEM

SHOULD BE SO MARKED AND THIS MARKING SHOULD BE PERFORMED IN

SUCH A MANNER THAT IT IS EASILY SEEN BY MAINTENANCE PERSONNEL.

15. PROVIDE SYNCHRONIZING MODULES IN FACU & FAPS TO SYNCHRONIZE

THE STROBES IN CORRIDORS, MULTI-PURPOSES ROOM, DINING ROOMS

AND ROOMS WHERE THERE ARE MORE THAN ONE STROBE.

16. PROVIDE CODING CARDS, MODULES AND OTHER HARDWARES IN FACU

AND FAPS'S TO SYNCHRONIZE ALL CHIME & STROBE INCLUDING

OUTDOOR

17. SMOKE DETECTORS SHALL BE PLACED 36 OR MORE INCHES AWAY FROM

AND OUT OF THAT AIR FLOW OF AN HVAC REGISTER.

18. COMBINED FIRE ALARM WITH ANY OTHER SIGNAL WIRINGS IN CONDUITS,

PULL BOXES AND UNDERGROUND BOXES SHALL NOT BE PERMITTED. IF IT

IS NOT POSSIBLE TO PROVIDE DEDICATED UNDERGROUND BOXES,

PARTITIONS OR SOME MEANS OF PHYSICAL AND ELECTRICAL

PROTECTION OF FIRE ALARM CONDUCTORS SHOULD BE PROVIDED.

19. REMOVE ALL ABANDONED CIRCUITS AND WIRING COMPLETELY RATHER

THAN LABELED.

20. PROVIDE PERMANENT LABEL ON DEVICES THAT WILL NOT EASILY

PEEL-OFF PARTICULARLY DEVICES ACCESSIBLE TO THE PUBLIC THIS

INCLUDES ADDRESS LABEL.

21. PANELS MUST NOT BE HIGHER THAN 6 FEET AND SYSTEM STATUS

DISPLAYS ARE TO BE AT EYE LEVEL (+60"AFF). NO EQUIPMENT OR

RACEWAY MAY BE LOCATED UNDER A CABINET CONTAINING BATTERIES.

22. CONTRACTOR WIRING MUST ENTER AT THE TOP OF FACU.

23. RUN 1#12 GREEN BOND WIRE IN NON-METALLIC RACEWAYS (PVC IN

UNDERGROUND RUNS). PROVIDE GROUNDING BUSHING AT CONDUIT

STUB-UP TERMINATED AT A PULL BOX.

24. SPLICING OF FA SYSTEM WIRING IN JUNCTION BOX IS NOT ALLOWED.

SPLICING SHALL BE PERFORMED ON FIRE ALARM EQUIPMENT AND IN

TERMINAL CABINETS.

25. JUNCTION BOXES SHALL NOT CONTAIN SPLICES. CONDUCTORS SHALL BE

PULLED THROUGH. TERMINATIONS SHALL BE PERFORMED IN TERMINAL

CABINETS OR IN FIRE ALARM EQUIPMENT TERMINALS.

26. PENETRATION OF FIRE RATED WALLS SHALL BE PROTECTED IN

ACCORDANCE WITH 2025 CALIFORNIA BUILDING CODE, SECTION 714.4.

27. PENETRATION OF FIRE RATED FLOORS/CELINGS SHALL BE PROTECTED IN

ACCORDANCE WITH 2025 CALIFORNIA BUILDING CODE, SECTION 714.5.

28. SEE DETAIL DRAWINGS FOR MOUNTING HEIGHT OF FIRE ALARM PULL

STATIONS, STROBES, HORNS AND COMBINATION STROBE AND HORN.

29. APPROVED LISTED FIRE STOPPING METHODS AND MATERIALS SHALL BE

APPLIED AROUND CONDUIT PENETRATIONS THROUGH FLOORS, WALLS

AND CEILINGS OF ALL CORRIDORS, STAIRWAY WELLS, MECHANICAL

ROOMS, EQUIPMENT ROOMS, MACHINE ROOMS, BOILER ROOMS,

ELEVATOR SHAFTS, ELECTRICAL ROOM, TRANSFORMER ROOM,

STORAGE, OFFICE WALLS WHICH ARE PART OF CLASSROOM WALLS AND

OTHER FIRE RATED STRUCTURES REQUIRED BY CODES. ALL

PENETRATION THROUGH WALL OR FLOOR/CEILING SHALL BE TREATED AS

A FIRE RATED PENETRATION. PATCHING AND FILLING SHALL BE DONE

USING A UL LISTED ASSEMBLY AND MATERIAL TO MATCH FIRE RATING OR

MINIMUM OF 1-HR.

30. PROVIDE TAGGING ON WIRES/CABLES TO IDENTIFY THE AUDIO CIRCUITS,

VISUAL CIRCUITS, POWER CIRCUITS, SLC LOOPS AND OTHER CIRCUITS.

31. FIRE ALARM SYSTEM SHALL TRANSMIT THE ALARM, SUPERVISORY AND

TROUBLE SIGNAL TO AN APPROVED SUPERVISING STATION AS REQUIRED

BY 2025 NFPA 72. THE SUPERVISING STATION SHALL BE LISTED AS OR

SHALL MEET THE REQUIREMENTS OF 2025 NFPA 72 AT A LOCATION

APPROVED BY THE STATE.

32. ALL USEABLE EXISTING FIRE ALARM COMPONENTS REMOVED FROM THIS

PROJECT SHOULD BE RETURNED TO THE DEPARTMENT OF JUSTICE AND

OPERATIONS AREAS FOR SALVAGE. THE DEPARTMENT OF JUSTICE'S

REPRESENTATIVE SHOULD BE CONSULTED TO DETERMINE IF ANY

COMPONENTS ARE SALVAGEABLE.

33. INTERFACING OF EXISTING FIRE ALARM DEVICES TO THE NEW FIRE

ALARM SYSTEM SHALL BE INCLUDED IN THE BIDDING. IT'S THE

RESPONSIBILITIES OF THE CONTRACTOR TO VERIFY ON SITE THE

EXISTING FIRE ALARM SYSTEM SUCH AS THE DEVICES TO BE

COMPATIBLE WITH THE NEW FIRE ALARM SYSTEM. ALL DEVICES

RECEIVING POWER FROM INITIATING DEVICE CIRCUIT SHALL BE LISTED

FOR USE WITH THE CONTROL UNIT. WHERE EXISTING DEVICES CONNECT

TO NEW FIRE ALARM, PROVIDE LISTING.

34. DAMAGED WALLS, CEILING OR ANY STRUCTURE DUE TO CONSTRUCTION

SHALL BE REPAIR AND PAINTED TO MATCH EXISTING.

35. PAINT CONDUIT TO MATCH WALLS. PAINT TO BE APPROVED BY

DEPARTMENT OF JUSTICE REPRESENTATIVE.

36. ALL WORKS ARE NEW UNLESS NOTED OTHERWISE.

37. WHEN CEILING SUSPENSION SYSTEMS, EQUIPMENTS SUPPORT SYSTEM,

LIGHTING FIXTURES, J-BOXES, OR OTHER ITEMS REQUIRED TO BE

REMOVED TO PERFORM THE WORK, THE CONTRACTOR SHALL BE

RESPONSIBLE FOR REPAINTING OR REPLACING ANY BROKEN OR

DAMAGED ITEMS, INCLUDING PATCHING WALLS AND PAINTING AS

REQUIRED, TO BRING THE AREA TO ITS ORIGINAL CONDITION.

38. ALL FIRE ALARM CIRCUITS ARE TO BE RUN IN 3/4" EMT CONDUITS, U.O.N..

CIRCUIT SURVIVABILITY LEVEL IS PERMITTED TO BE LEVEL "0", AS PER

2025 NFPA 72 SECTION 24.3.14.4.1.

39. THE SEISMIC BRACING AND ANCHORAGE OF ELECTRICAL CONDUITS, BUS

DUCT, WIREWAYS AND CABLE TRAYS (IF APPLICABLE) SHALL BE IN

ACCORDANCE WITH THE "GUIDELINE FOR SEISMIC RESTRAINS OF

MECHANICAL SYSTEM AND PLUMBING PIPING SYSTEMS "PUBLISH BY

SMACNA LATEST VERSION AND APPROVED BY STATE. A COPY OF THE

APPROVE GUIDELINE SHALL BE PROVIDED BY THE CONTRACTOR AND BE

KEEP AT THE JOB SITE AT ALL TIMES. WHERE BRACING AND ANCHORAGE

DETAIL ARE NOT SHOWN ON THE DRAWINGS OR IN THE GUIDELINE, THE

FIELD INSTALLATION SHALL BE SUBJECT TO THE APPROVAL OF THE

DEPARTMENT OF JUSTICE REPRESENTATIVE.

40. CUTTING, BORING, SAWCUTTING OR DRILLING THROUGH THE EXISTING

STRUCTURAL ELEMENTS TO BE DONE ONLY WHEN SO DETAILED IN THE

DRAWINGS OR ACCEPTED AND WITH THE APPROVAL OF DEPARTMENT OF

JUSTICE REPRESENTATIVE. CONTRACTOR SHALL PERFORM X-RAY TO

AVOID CUTTING OF RE-BARS.

41. CIRCUIT BREAKER FEEDING POWER TO ANY FIRE ALARM RELATED

EQUIPMENT SUCH AS FACU'S, REMOTE POWER SUPPLIES, VOICE

EQUIPMENT SYSTEM, ETC. BE IDENTIFIED AS TO BREAKER NUMBER,

PANEL LOCATION AND MADE LOCKABLE. BREAKER HANDLE SHALL BE

COLORED RED AND LABELED "FIRE ALARM". IDENTIFICATION SHALL BE

SIMILAR WITH SPACE AGE "ELOCK-FA" LABEL THE PANELBOARD "FIRE

ALARM CIRCUIT INSIDE" AND UPDATE DIRECTORY.

42. PROVIDE AND INSTALL FIRE RATED SLEEVE THROUGH FIRE RATED WALL

AS REQUIRED. RUN SURFACE MOUNTED RACEWAY THROUGH FIRE RATED

SLEEVE.

43. INSTALL SMOKE DETECTORS AT LEAST 1 FT AWAY FROM FLUORESCENT

FIXTURES TO AVOID UNWANTED ALARM.

44. EXTRA CAUTION WHEN WORKING IN THIS ROOM (OXYGEN STORAGE). NO

SMOKING AND USE OF FLAMMABLE DEVICES IN THIS ROOM. USE

EXPLOSION PROOF SMOKE DETECTOR AND CHICO SEALANT CONDUIT

ENTERING OXYGEN STORAGE ROOM.

45. CHANGES TO THE APPROVED DRAWINGS OR SPECIFICATIONS SHALL BE

MADE BY AN ADDENDA OR A CHANGE ORDER APPROVED BY

DEPARTMENT OF JUSTICE CONTRACTOR OFFICER.

46. AFTER COMMISSIONING OF THE NEW FIRE ALARM SYSTEM, THE EXISTING

FIRE ALARM SYSTEM IS TO BE REMOVED.

47. AUDIBLE DEVICES SHALL SOUND THE CALIFORNIA UNIFORM FIRE ALARM

SIGNAL IN TEMPORAL MODE.

48. VISUAL DEVICES SHALL NOT EXCEED 2 FLASHES PER SECOND AND SHALL

NOT BE SLOWER THAN 1 FLASH EVERY SECOND. SYNCHRONIZATION OF

STROBE IS REQUIRED.

49. ANY DISCREPANCIES BETWEEN THE DRAWING AND THE CODE

RECOGNIZED STANDARDS SHALL BE BROUGHT TO THE ATTENTION OF

THE INSPECTOR OF RECORDS.

50. WHERE THERE IS A CONFLICT BETWEEN THE DRAWINGS AND ANY

RELEVANT CODES, THE CODE SHALL GOVERN, EXCEPT WHERE THE

DRAWING INDICATE A QUALITY LEVEL SUPERIOR TO THAT SPECIFIED BY

THE CODES.

51. IN THE EVENT OF CONFLICT OR DISCREPANCY IN DRAWING/PLANS, IN

SPECIFICATION, BETWEEN DRAWINGS AND SPECIFICATION, BETWEEN

SITE CONDITIONS AND DRAWINGS, THE CONTRACTOR SHALL PROVIDE

THE MORE STRINGENT REQUIREMENTS.

52. CONTRACTOR WHEN PROVIDING THE BID PROPOSAL SHALL CONSIDER

THAT SOME IF NOT ALL AREAS HAVE DOUBLE CEILING.

53. CONCEAL RACEWAYS AND CABLES IN FINISHED AREAS AND MAY BE

EXPOSED IN UNFINISHED SPACES. INSTALL METAL WIREWAYS IN THE

FINISHED SPACES UPON APPROVAL OF DEPARTMENT OF JUSTICE.

54. IT IS CONTRACTOR'S RESPONSIBILITY TO OPEN THE CEILING/WALL TO

INSTALL CONDUITS AND BOXES. ONCE THE INSTALLATION IS COMPLETE,

THE CONTRACTOR SHALL RESTORE THE CEILING/WALL MAINTAINING THE

ORIGINAL CONDITION.

55. CUTTING, DRILLING AND ANY WORK RELATED TO CONCRETE OR OTHER

MATERIALS THAT CONTAIN CRYSTALLINE SILICA THAT MAY RESULT

EXPOSURE OF SILICA DUST TO ANY PERSONNEL SHALL BE REDUCED OR

CONTAINED BY THE CONTRACTOR IN ACCORDANCE WITH 29 CFR

1926.1153.

56. PROVIDE UL LISTED DOCUMENTATION CABINETS IN ACCORDANCE TO

2025 NFPA 72 SECTION 7.7.2. LABEL DOCUMENTATION CABINET "FIRE

ALARM SYSTEM RECORD DOCUMENTS". THIS WILL BE SIZED TO CONTAIN

ALL NECESSARY DOCUMENTS SUCH AS AS-BUILT DRAWINGS, O&M

MANUALS, TEST RECORDS, EMERGENCY RESPONSE PLAN, EVALUATION

DOCUMENTATION, ETC. AS STIPULATED IN 7.7.2.3. COORDINATE WITH

THE FIRE CHIEF OR FIRE PREVENTION COORDINATOR FOR THE

LOCATION.

57. PROVIDE LABEL ON FIRE ALARM CONTROL UNIT TO IDENTIFY THE

LOCATION OF THE RESPECTIVE DOCUMENTS.

58. EXISTING SMOKE FIRE DAMPERS SHALL BE CONTROLLED GLOBALLY

USING A CONTROL RELAY CONNECTED TO THE NEW FIRE ALARM SYSTEM.

59. A CERTIFICATE OF COMPLIANCE SHALL BE PREPARED BY THE INSTALLER

AND GIVEN TO THE DEPARTMENT OF JUSTICE UPON COMPLETION OF THE

INSTALLATION.

60. IN ALL AREAS OTHER THAN SUSPENDED ACOUSTIC TILE CEILINGS

(IDENTIFIED AS "TBAR" ON DRAWINGS) ASSUME THE CEILINGS TO BE

HARDLID CEILINGS. THE CONTRACTOR MUST INCLUDE IN HIS BID ALL

WORK AND MATERIAL REQUIRED FOR THE HARD CEILINGS TO BE CUT OR

OPENED AS REQUIRED TO RUN NEW CONDUITS. THE CEILINGS WILL THEN

NEED TO BE PATCHED AND REPAIRED BACK TO ORIGINAL CONDITION.

THE CUTTING/OPENING AND PATCHING/REPAIR OF CEILINGS IS NOT

SHOWN ON THE FIRE ALARM DRAWINGS.

61. ALL POWER BRANCH CIRCUITS SHALL BE MINIMUM OF 3/4"C-2#12 + 1#12G.

UPSIZE CONDUCTOR SIZE FOR LENGTHS EXCEEDING 150 FEET.

62. WHEN REMOVING EXISTING DEVICES AND COMPONENTS FROM WALL OR

CEILING, PROVIDE COVER PLATE FOR EXISTING BACKBOX OR PATCH

CEILINGS AND WALLS WHERE POSSIBLE. IN CASE OF SURFACE MOUNTED

CONDUIT OR BOXES, REMOVE ALL SURFACE MOUNTED RACEWAY AND

BOX SYSTEM COMPLETELY, UNLESS BURIED, THEN CONDUIT MAY BE

ABANDONED IN PLACE. IN ALL CASES, COMPLETELY REMOVE

WIRING/CONDUCTORS FROM DEVICES BACK TO SOURCE.

DELEGATED DESIGN AND SHOP DRAWINGS

SUBMITTAL SCOPE OF WORK

1. THIS CONSTRUCTION DOCUMENT SET IS INTENDED TO GENERALLY

PORTRAY THE SCOPE OF THE FIRE ALARM NETWORK, CENTRAL

MONITORING STATION, INITIATING DEVICES AND NOTIFICATION

APPLIANCE COVERAGE TO BE USED AS GUIDANCE FOR THE

CONTRACTOR WHEN PREPARING THE DELEGATED DESIGN SHOP

DRAWINGS. NOT ALL INFORMATION, INCLUDING BUT NOT LIMITED TO THE

EXACT ROUTING OF RACEWAYS, WIRING/CONDUCTORS, VOLTAGE DROP

CALCULATIONS, BATTERY SIZING AND MONITOR/RELAY MODULE DETAILS

HAVE BEEN INCLUDED IN THIS DOCUMENT SET.

2. IT IS THE RESPONSIBILITY OF THE CONTRACTOR TO VERIFY THE

INFORMATION IN THE CONSTRUCTION DOCUMENTS BASED ON ACTUAL

FIELD CONDITIONS AND MAKE THE APPROPRIATE ADJUSTMENTS TO THE

SYSTEM DESIGN, INCLUDING BUT NOT LIMITED TO THE INITIATING DEVICE

COVERAGE, NOTIFICATION APPLIANCE COVERAGE, QUANTITY OF POWER

SUPPLIES (NACs) REQUIRED FOR NOTIFICATION APPLIANCE CIRCUITS, TYPE AND QUANTITY OF MONITOR/RELAY MODULES IN A DETAILED SHOP

DRAWING SUBMITTAL.

3. THE DETAILED SHOP DRAWING SUBMITTAL MUST BE PRODUCED BY A

QUALIFIED, LICENSED AND CERTIFIED FIRE ALARM SYSTEM DESIGNER

AND SUBMITTED AS A COMPLETE SET OF DOCUMENTS AND

SPECIFICATIONS BASED ON THE COVERAGE AND PERFORMANCE

REQUIREMENTS DESCRIBED IN THIS CONSTRUCTION DOCUMENT SET

AND PERTINENT SPECIFICATIONS AS WELL AS ALL APPLICABLE CODES,

STANDARDS AND CLIENT TECHNICAL DESIGN GUIDELINES (TDG).

4. THE DELEGATED DESIGN DRAWINGS SUBMITTAL WILL BE REVIEWED BY

THE CLIENT AND THE ENGINEER OF RECORD.

5. REFER TO SPECIFICATIONS FOR FURTHER INFORMATION ON

REQUIREMENTS OF DELEGATED DESIGN AND SHOP DRAWING

SUBMITTALS, WITH SPECIAL ATTENTION TO SECTION 28 46 21.11

"ADDRESSABLE FIRE-ALARM SYSTEMS".

LEGEND

KVA KILOVOLT-AMPERE

KW KILOWATTS

L LENGTH

MECH. MECHANICAL

MISC. MISCELLANEOUS

MAX. MAXIMUM

MIN. MINIMUM

MFR. MANUFACTURER

MM. MILLIMETER

MM MONITOR MODULE

MED MEDICAL

(N) NEW

N.I.C. NOT IN CONTRACT

NO. NUMBER

N.O. NORMALLY OPEN

N.C. NORMALLY CLOSED

NCA NETWORK CONTROL

ANNUNCIATOR

N/O NORMALLY OPEN

N/C NORMALLY CLOSE

NAC NOTIFICATION APPLIANCE

CIRCUIT

P POLE, PHASE

PB PULL BOX

PR PAIR

PNL PANEL

PIV POST INDICATOR VALVE

PVC POLY VINYL CHLORIDE

PREP. PREPARATION

RES. RESISTOR

RM. ROOM

RTU ROOF TOP UNIT

STP SHIELDED TWISTED PAIR

SFD SMOKE FIRE DAMPER

SLC SIGNALING LINE CIRCUIT

SCH SCHEDULE

SYNC. SYNCHRONIZE

TEL TELEPHONE

TYP TYPICAL

U.N.O UNLESS NOTED

OTHERWISE

UG UNDERGROUND

UTP UNSHIELDED TWISTED

PAIR

UL UNDERWRITER

LABORATORIES

VOLT VOLTAGE

W/ WITH

WP WEATHER PROOF

W WIDTH

ABBREVIATIONS

A AMPERE

ADMIN. ADMINISTRATION

ARCH. ARCHITECTURE

AFF. ABOVE FINISHED FLOOR

AWG. AMERICAN WIRE GAUGE

AH AMPERE HOUR

A/C AIR CONDITIONING

ANN. ANNUNCIATOR

BLDG BUILDING

CD CANDELA

CB CIRCUIT BREAKER

C CONDUIT

C.O. CONDUIT ONLY

CKT CIRCUIT

CKT. BRK. CIRCUIT BREAKER

CM CONTROL MODULE

COMM COMMUNICATION

CONC. CONCRETE

CORR. CORRIDOR

DWG. DRAWINGS

DEPT. DEPARTMENT

DD DUCT DETECTOR (SMOKE)

(E) EXISTING

EOR ENGINEER OF RECORD

EOL END OF LINE RESISTOR

EQUIP. EQUIPMENT

ELECT. ELECTRICAL

EMERG. EMERGENCY

EXT. EXTERNAL

FATC FIRE ALARM TERMINAL

CABINET

F.A OR FA FIRE ALARM

FACU FIRE ALARM CONTROL

PANEL

FAPB FIRE ALARM PULL BOX

FCU FAN COIL UNIT

FS FOOD SERVICE

FL FLOOR

FIG FIGURE

FLEX. FLEXIBLE

FT. FEET

FTU FIBER TERMINATION UNIT

GND GROUND

HRS HOURS

HVAC HEATING VENTILATING AIR

CONDITIONING

ID IDENTIFICATION

INFO. NFORMATION

AUTOMATIC FIRE ALARM SYSTEM SHALL TRANSMIT THE ALARM,

SUPERVISORY AND TROUBLE SIGNALS TO THE UL LISTED CENTRAL

MONITORING AND CONTROL WORKSTATION PROVIDED AS A PART OF

THIS SCOPE OF WORK AND TO BE LOCATED IN THE CONTROL ROOM.

SUPERVISION OF SYSTEM ARRANGED BY DEPARTMENT OF JUSTICE.

FIRE ALARM MONITORING NOTE

15 = 33%8 = 18%

7 = 15% 14 = 30%

13 = 28%6 = 13%

12 = 25%5 = 10%

11 = 23%4 = 8%

3 = 6% 10 = 21%

9 = 19%2 = 4%

#12 IN 3/4"C

3/4" .824 .68

2I.D.I.D.SIZE

CONDUIT

.015.12212

2O.D.

WIRE TYPE "THHN"

AWG O.D.

= % FILLFORMULA = (WIRE O.D.) X WIRE QTY. X 100

(CONDUIT I.D.)

CONDUIT % FILL CALCULATIONS

FIRE ALARM TERMINAL CABINET, WALL MOUNTED,

CABINET SHALL HAVE A LOCKABLE HINGED DOOR

WITH A DOOR MOUNTED LOCK.

PROVIDE ALL REQUIRED TERMINAL STRIPS AND

NAMEPLATE

SIZE: 18"x18"x6" OR SIZE AS REQUIRED

JUNCTION BOX. 4" SQ.

PULLBOX

ELECTRICAL PANELBOARD

FATC

LEGEND NOTES:

1. SEE DWG FA0.2 FOR COMPLETE SYMBOL LEGEND OF FIRE ALARM

SYSTEM DEVICES AND COMPONENTS.

LIGHT, THIN LINES INDICATE EXISTING

HEAVY, THICK LINES INDICATE NEW

HEAVY, THICK, DASHED LINES INDICATE

UNDERGROUND CONDUIT

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

FA0.2

FIRE ALARM - SYMBOL LIST

AND SEQUENCE OF

OPERATION

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

dw g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

WHERE FLOW SWITCH/TAMPER SWITCHES ARE INDICATED ON DRAWINGS PROVIDE

COMPLETE WITH ALL REQUIRED MODULES AND OUTDOOR BELL. REFER TO DETAIL 8/FA0.4

AND DETAIL 6/FA0.4 AND 7/FA0.4. ASSUME NEW POWER SUPPLY REQUIRED FOR ALL

SPRINKLER BELLS.

PROVIDE SYNCHRONIZATION AND ACTIVATION MODULES FOR ALL BOOSTER POWER

SUPPLIES.

SEE SHEET FA0.5 DETAIL 2.

SURFACE

BACKBOX

PROVIDED

4"S 2-1/8" BOX

ON BASE

4"S 1-1/2" BOX

ON DUCT

4"S 1-1/2" BOX

ON BASE

4"S BOX

DESCRIPTION

FACU

REMARKS

4"S 2-1/8" BOX

FIRE ALARM CONTROL UNIT

BOOSTER POWER SUPPLY

LCD REMOTE ANNUNCIATOR

INTELLIGENT LOW-FLOW

PHOTOELECTRIC DUCT DETECTOR

TAMPER SWITCH

HORN/STROBE 15-110 CD

SELECTABLE CANDELLA (WALL MOUNTED)

FIRE ALARM SPRINKLER BELL 10"

VIBRATING, DIODE 20-24VDC

SAMPLING TUBE (LENGTH AS

REQUIRED)

INTELLIGENT HEAT DETECTOR

INTELLIGENT PHOTOELECTRIC SMOKE

DETECTOR

INPUT/MONITOR MODULE

CONTROL RELAY MODULE

STANDARD BASE OR ISOLATOR BASE

4"S BOX

FAA

AOM

AIM

HSCM

E N

O T

M O

M S

M O

FACU POWER FAILURE

DEVICE DISCONNECTION, GROUND,

OPEN, SHORT

SPRINKLER TAMPER SWITCH

WATER FLOW SWITCH

DUCT DETECTOR

HEAT DETECTOR

AREA SMOKE DETECTOR

M S

LSY

MANUAL PULL STATION

DEVICE ACTIVITY AC

M O

M S

X X

CONTROL UNIT

ANNUNCIATION

NOTIFICATION REQ. FIRE

SAFETY

SUPP.

N O

O N

M O

O N

S M

D O

M O

- D

O R

FIRE PUMP TROUBLE

FIRE PUMP RUNNING

FIRE ALARM SYSTEM LOW BATTERY

NOTIFICATION APPLIANCE

CIRCUIT SHORT

X X

O F

X X

FIRE ALARM SYMBOL LIST

FIRE ALARM SEQUENCE OF OPERATION

KEYNOTES:

MODEL NO.

FIREWORKS

SYMBOL OR

ABBREV.

INCIDENT MANAGEMENT COMMAND AND

CONTROL PLATFORM

EST-4

BPS6A

E-RLCD

SIGA-CR

SIGA-CT1/CT2

SIGA-OSD

MANUFACTURER

EST

4"S 2-1/8" BOXISOLATOR MODULEIM SIGA-IM

SIGA-HFD

EST

SIGA-SD

SD-TXX

G4AVRF

RTS REMOTE ALARM INDICATING & TEST

SWITCH

SD-TRK EST

EST

439D-10AW-R

SIGA-CR

MR-100 SERIES HVAC SHUTDOWN CONTROL CIRCUIT

CD STROBE 15-110 CD

SELECTABLE CANDELLA (WALL MOUNTED)G4VRF EST

WFD

OSY2

SPRINKLER WATER FLOW SWITCH

PROVIDED

4"S 1-1/2" BOX

WEATHERPROOF BACKBOX

EST

SYSTEM SENSOR

SIGA-SB

OR SIGA-IB

SIGA-SB

OR SIGA-IB STANDARD BASE OR ISOLATOR BASE

EST

4"S BOXSTROBE 15-110 CD SELECTABLE

CANDELLA (CEILING MOUNTED)GCVRF EST

4"S BOXHORN/STROBE SELECTABLE, 15-110CD

(CEILING MOUNTED)

GCAVRF EST

4"S BOXWEATHERPROOF HORN/STROBE 15-110 CD

SELECTABLE CANDELLA (WALL MOUNTED)WG4RF-HVMC EST

CONDUCTOR COLOR

WIRE IN CONDUIT

INSULATION

DEVICE/FUNCTIONSYMBOL

JACKET

BLDG. INTERIOR (ADDRESSABLE LOOP)

ADDRESSABLE INITIATING CIRCUIT LOOP RED/BLACK RED 2 CONDUCTOR #16 FPL SOLID

TWISTED/UNSHIELDED WEST PENN #D990

POWER SUPPLY DEVICE - 24VDC RED/BLACK REDP 2#12 STRANDED TYPE THHN

NETWORKING CIRCUIT BETWEEN FACUS BLACKN 12 STRAND SINGLE-MODE FIBER

NOTE: WHERE GRAPHIC ANNUNCIATORS ARE REQUIRED, PROVIDE ADDITIONAL FIBER/COPPER MODULE IN FACU AS

REQUIRED TO INTERFACE WITH THE NETWORK GRAPHIC ANNUNCIATOR.

FIRE ALARM WIRE LEGEND

12/2 SOLID COPPER CONDUCTORS,

UNSHIELDED WITH AN OVERALL JACKETVISUAL NOTIFICATION DEVICES RED/BLACK REDV

ON BASE

4"S 1-1/2" BOX

INTELLIGENT MULTI-SENSOR SMOKE,

HEAT, CO DETECTOR

STANDARD BASE

SIGA-OSHCD EST

ESTSIGA-SB

FAPS

GCC

SCREW COVER ENCLOSURE,

SIZED AS REQUIRED

F ESTSIGA-270

F KEY RESET PULL STATION ESTRGS RMS-1P-KLK SINGLE GANG BOX

SINGLE GANG BOX

ONE STAGE FIRE ALARM STATION W/

SIGA-CT1 INPUT/MONITOR MODULE

1 2 NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

FA0.3

FIRE ALARM DETAILS

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

dw g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

72" A.F.F

MAX.

TRANSPONDER

FINISHED FLOOR

CEILINGTO SMOKE/ FIRE

DAMPERS

SCROLL DISPLAY

HOLD 2 SECONDS

SCROLL DISPLAY

FIRE AL;ARM

ACKNOWLEDGE

SCROLL DISPLAYSCROLL DISPLAY

SECURITY TROUBLESUPERVISORY

SILENCE

SIGNAL DRILL

RESET

SYSTEM

SCROLL DISPLAY

OTHER EVENT

LAMP TEST

72" A.F.F

MAX.

72" A.F.F

MAX.

3-LCD

ANNUNCIATOR

GREEN LED

(NORMAL)

N.C.

MR-101/C

N.O.

COMMON

COM

TO 24 V.

CONNECTION

SIGA-CR

RED LED

(ALARM/ACTIVE)

TB2

TB1

NORMALLY-CLOSEDNORMALLY-OPEN

DATA IN (+)

DATA IN (-)

DATA OUT (+)

DATA OUT (-) TO NEXT

DEVICE

(N)

(H)

SLC LOOP

TO FACP OR

INITAITING

DEVICE

HEAT DETECTOR

SIGA-HFP

SMOKE DETECTOR

SIGA-OSD

FAPS POWER

SUPPLY

SMOKE/HEAT DETECTORS BACKBOX MOUNTING ELEV. DETAIL

NOT TO SCALE

FIRE ALARM

PANEL

FIRE ALARM

PANEL

BATTERY

BACKBOX

CONTROL RELAY (SIGA-CR) CONNECTION

FAN/DAMPER CONTROL WIRING DETAIL1 NOT TO SCALE 2 3

NOT TO SCALE

NOTE:

MR-101/C RELAY PROVIDES 10Amp

FORM C CONTACTS.

5 TYPICAL FACU/FATC/FAPS MOUNTING ELEVATION DETAIL

TB3

TB1TB2

SIGA-CT1

BPS6A

NAC 3

AUX.

NAC 1

NAC 2

OUT

COM

OUT

AC AUX

G N

TROUBLE

SENSE 2

S1 ABS2

BATTERY

TB4

L GN

TB3

DATE

SENSE 1

DATA IN (-)

DATA IN (+)

TO BATTERIES

TO DEDICATED 120VAC

SIGA-CC1

OUTPUT #4

STYLE Y (CLASS B)

NOT TO SCALE

NOT USED

SPRINKLER BELL CONNECTION TO REMOTE POWER SUPPLY (FAPS) WIRING DETAIL

MOUNTING HEIGHT REQ. SMOKE HEAT

DET, KEY STATION, AUDIO VISUAL DEVICE

NOT TO SCALE 6

NOT TO SCALE

DATA OUT (+)

DATA OUT (-)

DEVICE

GREEN LED

(NORMAL)

RED LED

(ALARM/ACTIVE)

SPRINKLER

BELL

FLOW

SWITCH

NAC OUTPUT #1

NAC OUTPUT #2

NAC OUTPUT #3

EOL

15K

EOL

15K

EOL

15K

(FOR AUDIBLE CIRCUIT ACTIVATION)

(FOR VISUAL CIRCUIT ACTIVATION)

GREEN LED

(NORMAL)

RED LED

(ALARM/ACTIVE)

FROM SIGNATURE

CONTROLLER OR PREVIOUS

DEVICE

4" MIN

DETECTOR

BACK BOX

I R

BACK BOX

KEY STATION

AUDIBLE DEVICE

@ 96" MAX

A.F.F. PER SEC

18.5.5.1 NFPA 72

2025 ED.

90" MIN. A.F.F. OR

6" MIN. BELOW

CEILING PER SEC

18.4.10.1 NFPA 72

2025 ED.

@ 80" MIN.

A.F.F. PER SEC

18.5.5.1 NFPA

72 2025 ED.

@ 48". A.F.F. PER

SEC 17.17.7 OF

NFPA 72 2025 ED.

FINISHED

FLOOR

@ 42".

A.F.F.

NEVER HERE

TOP OF DETECTOR

ACCEPTABLE HERE

VISUAL/AUDIO

VISUAL DEVICE

VISUAL/AUDIO

VISUAL DEVICE

" M

4" M

3' MIN

A/C SUPPLY OR

RETURN DIFFUSER

BACK

BOX

FINISHED WALL

5' MAX TO

EXIT DOOR

MANUAL KEY

STATION

FINISHED WALL

1-1/4"C

(AS REQUIRED)

FATC

WALL

120V AC

(2)2"C

DO NOT INSTALL ANY CONDUIT ON THE

BOTTOM OF THE CABINET. THIS AREA IS

RESERVED FOR BATTERY PLACEMENT.

COORDINATE SIZE WITH MANUFACTURER'S

SPECS.

THE MOUNTING HEIGHT OF THE

EQUIPMENT IS FOR REFERENCE ONLY.

FIELD VERIFY HEIGHT WITH I.O.R.

ELECTRICAL CONTRACTOR SHALL

CONFIRM THE DIMENSION OF ALL

EQUIPMENTS PRIOR TO INSTALLATION.

INSTALL WITHIN 3 FEET OF ASSOCIATED

FIRE ALARM CONTROL PANEL.

ACTUAL QUANTITY OF REMOTE POWER

SUPPLIES MAY VARY @ FIELD.

MINIMUM SIZE OF FATC NEXT TO FACP

SHALL BE 18"X18"X4" U.O.N.

3/4"C TO

DEVICES

CEILING LEVEL

WALL

VERIFY CONDUIT SIZE @

FIELD 2-3/4"C MIN.

120V

FAPS

FACU

ROUGH-IN

10"

MIN

BC-1

BATTERY

ENCLOSURE

FINISHED FLOOR LEVEL

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

FA0.4

FIRE ALARM DETAILS

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

dw g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of General Services

BID DOCUMENT - NOT FOR CONSTRUCTION

SIGA-CRMR-101-C SIGA-CT2

GUTTTER

NEXT TO ELEVATOR SHUNT TRIP CONTROLLER

1/2"C. 3/4"C. 3/4"C.

MR-101-C

1/2"C.

1/2"C. 1/2"C.

3/4"C

TB1

TB2

DATA OUT (-)

TO NEXT DEVICE

DATA OUT (+)

TO NEXT DEVICE

REMOTE LED

(SIGA-LED)

DATA IN (-)

- OPTIONAL DEVICE WIRING.

1 H + H -

4 S - S +

FIRST DEVICE

1 H +

S - S + H -

TO FA SYSTEM

(SLC & TO 24V.

SUPERVISED

OUTPUT

BATTERY BACK UP)

4"S

J-BOX

120 VOLT, 20AMP

SHUNT TRIP

CONTROL

CIRCUIT

TYPICAL N.O.

INITIATING

DEVICE/ MONITOR

CONTACT

STYLE B (CLASS B)

UL/ULC LISTED

47K EOL

GREEN LED

(NORMAL)

RED LED (ALARM/ACTIVE)

DATA IN (+)

DATA IN (-)

DATA OUT (+)

DATA OUT (-)

TO NEXT

DEVICE

FROM SIGNATURE

CONTROLLER OR

PREVIOUS DEVICE

TO UL/ULC

LISTED FACP

SIGNAL CIRCUIT

TO UL/ULC

LISTED FACP

SIGNAL CIRCUIT

SPEAKER AND

STROBE ON

SEPARATE CIRCUIT

TO NEXT DEVICE

OR EOL

RESISTOR

TO NEXT DEVICE

OR EOL

RESISTOR

SPEAKER

STROBE

SPEAKER

MAX. RESIST. PER

WIRE MUST NOT

EXCEED 10 OHM

DATA IN (+)

TO SHUNT

TRIP CIRCUIT

BREAKER

1 NOT TO SCALE 2 NOT TO SCALE

ISOLATION RELAY/ADDRESSABLE

MODULE LAYOUT FOR SHUNT TRIP

CONTROL/MONITOR DETAIL3 NOT TO SCALE

BACK BOX

INCLUDED

4"S W/

1 GANG RING

4"S W/

1 GANG RING

BACK BOX

INCLUDED

4"S

J-BOX

4 NOT TO SCALE

5 NOT TO SCALE

CONDUIT LENGTH NOT MORE

THAN 3 FEET TO ELEVATOR

SHUNT TRIP BREAKER.

NOTES:

FROM SIGNATURE

CONTROLLER OR PREVIOUS

DEVICE

NOTES:

TYPICAL FATC/FAPS (SUGGESTED)

ELEVATION DETAIL

SINGLE INPUT MODULE

(SIGA-CT1) WIRING DETAIL

TYPICAL HORN STROBE

WIRING DIAGRAM

SMOKE DETECTOR BASE

(SIGA-SB) WIRING DETAIL

FINISHED FLOOR

G S

SYSTEM

HORIZONTAL RISER DETAIL

CONTROL VALVE

SUPERVISORY SWITCH

WATERFLOW

SWITCH

FLEXIBLE CONDUIT

(TYPICAL)

WATERFLOW

MONITORING ZONE

(TYPICAL)

DUAL MONITOR MODULE

VALVE SUPERVISORY

MONITORING ZONE

(TYPICAL)

3/4" RACEWAY

FLOW SWITCH AND

CONTROL VALVES

HOSE VALVE

BUTTERFLY-VALVE

WITH TAMPER

MONITORED

DUAL

MONITOR

MODULE

VERTICAL RISER DETAIL 6 NOT TO SCALE 7 NOT TO SCALE

BPS6A

OUT

COM

OUT

AUX

1011 12

G N

S1 ABS2

BATTERY

TB4

1 52 43 6 7

L GN

TB3

DATE

BATTERY

ROUTE AC SUPPLY

THROUGH THESE

KNOCKOUTS ONLY

(NONPOWER-LIMITED

AND SUPERVISED)

POWER-LIMITED

WIRING AREA

1- MAINTAIN 1/4" SPACING

BETWEEN POWER-LIMITED AND

NONPOWER-LIMITED WIRING OR

USE TYPE FPL, FPLR OR FPLP

CABLE PER NEC.

2- POWER-LIMITED AND

SUPERVISED WHEN NOT

CONFIGURED AS AUXILIARY

POWER. NON-SUPERVISED

WHEN CONFIGURED AS

AUXILIARY POWER.

3- SOURCE MUST BE

POWER-LIMITED. SOURCE

DETERMINES SUPERVISION.

4- WHEN USING LARGER

BATTERIES, MAKE SURE TO

POSITION THE BATTERY

TERMINALS TOWARD THE DOOR.

NOTES:

BATTERY WIRING

(NONPOWER-LIMITED AND

SUPERVISED)

SIGA-HFS

DATA IN(+)

DATA IN(-)

DATA OUT(-)

DATA OUT(+)

5 6 5

SIGA-IPHS

DATA IN(+)

DATA IN(-)

DATA OUT(+)

DATA OUT(-)

INTELLIGENT FT. HEAT DETECTOR

BASE WIRING DIAGRAM

NOT TO SCALE 10

INTELLIGENT 4D MULTI SENSOR

DETECTOR BASE WIRING DIAGRAM

NOT TO SCALE

TO NEXT

DEVICE

TO NEXT

DEVICE

FROM FACP

DEVICE

FROM FACP

DEVICE

1534-1

SIGA-CT1

GREEN LED

(NORMAL)

MANUAL KEY SWITCH STATION

EOL

RED LED

(ALARM/ACTIVE)

FROM SIGNATURE

CONTROLLER OR

PREVIOUS DEVICE

TO NEXT DEVICE

DATA OUT (+)

DATA OUT (-)

DATA IN (+)

DATA IN (-)

2#18 THHN/FPL

11 NOT TO SCALE

MANUAL PULL STATION WITH

SIGA-CT1 WIRING DIAGRAM

12 NOT TO SCALE

FAPS WIRING DETAIL

NOTIFY

FIRE DEPT.

WHEN ALARM

SOUNDS

1. SIGN SHALL BE BAKELITE LAMINATED PLASTIC WITH WHITE

BACKGROUND.

2. ALL LETTERING SHALL BE RED, FLAT FACE GOTHIC LETTERS.

NOTES:

1'-10"

1, -4

SIGN FOR FIRE RISER BELL 8 NOT TO SCALE

2"C

WALL

4S BOX

FINISHED FLOOR LEVEL

CEILING LEVEL

NOTE: FIELD VERIFY ALL HEIGHTS & CONDUIT SIZES

DEVICES

TO FLOOR ABOVE

(IF APPLICABLE) VERIFY CONDUIT

SIZE @ FIELD

2-3/4"C MIN.

120VAC

DEDICAT. CKT.

FATC FAPS

MIN

10"

MIN

NOT FOR

CONSTRUCTION

OFFICE OF THE STATE FIRE MARSHAL

APPROVED WORKING DRAWINGS. PROCEED TO BID

25-3867

5/22/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

DSA

D E P A R T M E N T O F G E N E R A L S E R V I C E S

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

DSA

DIVISION OF THE STATE ARCHITECT

IDENTIFICATION STAMP

DIV. OF THE STATE ARCHITECT

APP: INC:

REVIEWED FOR

SS FLS ACS

DATE:

02-124365

7/7/2026

FA0.5

FIRE ALARM DETAILS

N M L K J I H G

Checked

Vault File Number

DSA Building Number

Reference North Sheet Scale

Sheet Number

Work Order

Designed

Sheet Title

Supervisor

File Date

Drawn

DescriptionNo. Date

Issue:

F E D C B

-05/13/2026

C op yr ig ht

5, C al ifo rn ia

D ep ar tm en t o f G en er al

S er vi ce s

- R ea l E st at e Se rv ic es D iv is io n

DGS PROJECT # DGS000000XXXXX

SFM FAC #XX-XX-X-XXXX

JCCA#: 24690-2

: L :\2

Fi re

A la rm , R iv er si de

F or en si c La b, D

O J\

dw g D

M ay

6, 5:

JCCA

DSA STAMP

RIVERSIDE LAB FIRE

ALARM REPLACEMENT,

RIVERSIDE FORENSIC

LABORATORY

7425 MISSION BLVD

RIVERSIDE, CA

92509

Project

AS SHOWN

XX-X-XXXX-X-XX

PLAN CHECK CORRECTIONS

385 VAN NESS AVE., SUITE 208, TORRANCE, CA 90501

P: 310.212.7644 F:310.212.5272I

707 Third Street Facilities Management Division

State of California

West Sacramento, California 95605

Department of…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Aug 31, 2026.