Amendment 0001 1282B125Q0001.pdf

(x)

1282B125Q0001 x x

1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted ; or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGEMENT TO BE

RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR

OFFER. If by virtue of this amendment you desire to change an offer already submitted , such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

x

82B1

WASHINGTON DC 20250-0001

1400 INDEPENDENCE AVE SW MS-1138

SPOC INTERMOUNTAIN

USDA FOREST SERVICE

10/08/20240001

13. THIS ITEM ONLY APPLIES TO MODIFICATION OF CONTRACTS/ORDERS. IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

12. ACCOUNTING AND APPROPRIATION DATA (If required) is not extended.is extended, Items 8 and 15, and returning

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended , by one of the following methods: (a) By completing

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

FACILITY CODE CODE

10B. DATED (SEE ITEM 13)

10A. MODIFICATION OF CONTRACT/ORDER NO.

9B. DATED (SEE ITEM 11)

9A. AMENDMENT OF SOLICITATION NO.

CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code)

7. ADMINISTERED BY (If other than Item 6)CODE 6. ISSUED BY

PAGE OF PAGES

4. REQUISITION/PURCHASE REQ. NO.3. EFFECTIVE DATE2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO. (If applicable)

1. CONTRACT ID CODE

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

09/18/2024

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority) appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

E. IMPORTANT: Contractor is not is required to sign this document and return __________________ copies to the issuing office.

ORDER NO. IN ITEM 10A.

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)15A. NAME AND TITLE OF SIGNER (Type or print)

15C. DATE SIGNED 16B. UNITED STATES OF AMERICA 15B. CONTRACTOR/OFFEROR 16C. DATE SIGNED

(Signature of person authorized to sign) (Signature of Contracting Officer)

JEFFREY R. BLACK

STANDARD FORM 30 (REV. 11/2016)

Prescribed by GSA FAR (48 CFR) 53.243

Previous edition unusable

Except as provided herein, all terms and conditions of the document referenced in Item 9 A or 10A, as heretofore changed, remains unchanged and in full force and effect .

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

The purpose of this amendment is to provide questions and answers. (see page 2)

Please provide a signed copy of this amendment or acknowledge box 19 within the Solicitation at the time of proposal. Acknowledgment of this amendment is required in order for the contractor to be considered responsible.

Period of Performance: 11/04/2024 to 12/31/2024

Continuation of SF 30

Question 1: Is there going to be a site visit?

Answer 1: There will not be a site visit.

Question 2: One 50-amp 240-volt circuit and receptacle, -- can you please clarify what this outlet will be used for?

Answer 2: This outlet will be used to power a welder; a Miller Multimatic 220 AC/DC

Question 3: Two 20-amp 240-volt circuits, -- can you please clarify what these 2 outlets will be used for?

Answer 3: One circuit will power a refrigerator and the other will be used to power a desiccant cabinet.

Question 4: 120-volt circuits with fourteen receptacles, referenced in page 6 figure 5 -- SOW states 120v "Circuits", do you have a specific number of circuits in mind or is that left up to the electrical contractor to determine. Also are these 120v receptacles BOTH wall outlets AND overhead lighting outlets OR just wall outlets? also in figure 8, page 9, the outlets being installed extend to the 2nd floor? Are these 120v outlets limited to 2 floors only?

Answer 4: The specific number of circuits will be left to the contractor to decide. The 120v receptacles are only wall outlets. The 120v outlets will be on two floors in the same building.

Question 5: Does the electrician have to be licensed in Idaho or is it sufficient to have the electrician licensed in another state?

Answer 5: The electrician performing work must be state licensed but does not have to be Idaho specific licensed.

Question 6: one 240-volt circuit with ceiling mounted receptacle -- Can you please provide what this dedicated 240v single receptacle circuit would be used for? Can you clarify the amperage because 240v is too vague, we need more information regarding the amperage since that determines wire and raceway size.

Answer 6: The 240v single receptacle will be used for an electric hoist. The specifications will be equivalent or similar to:

Question 7: Is the SOW all in ONE building spanning multiple floors or different buildings? Are all the new circuits originating from the new sub panel being installed?

Answer 7: The work outlined in the SOW is all in one building, spanning two floors. All new circuits will originate from the installed new sub panel.

Question 8: For the new circuits, can the raceways be surface mounted, or do you expect us to demo walls and run the raceways through studs and joists? If so, is patch and repair work the responsibility of the electrical contractor?

Answer 8: The new circuits can be surface mounted where wall is finished/covered and interior mounted on open unfinished walls. The majority of the work will be surface mounted.

Question 9: I noticed that all vehicles entering the park need to be pressure washed. Do you know if there is a designated area where this is to be done? Will a pressure washer be provided, or do you think we'll need to bring one?

Answer 9: It is expected that all vehicles entering the compound are clean and free of mud/soil/natural material. Cleaning supplies/pressure water will not be provided, but there is a public self-use car wash located 1 mile from the work site.