124PSA27Q0041 Solicitation.pdf

PDF 322 KB Posted

Attached to
WS FIXED WING FLIGHT SERVICES
Solicitation number
124PSA27Q0041
Issued by

About this file

This is a Request for Quote (RFQ) for fixed-wing aircraft flight services supporting wildlife damage management operations in North Dakota for the United States Department of Agriculture (USDA), Animal and Plant Health Inspection Service (APHIS), Wildlife Services (WS).

The contractor must furnish, operate, and maintain one fixed-wing aircraft (Piper PA18, Cub Crafter CC 18, or X-Cub) to provide aerial flying task orders for wildlife damage management, predation mitigation, disease monitoring, invasive species removal, and emergency response operations. The aircraft must be equipped with dual controls, operational intercommunication systems, lap belt and shoulder restraints with inertial reels, FAA-approved emergency locator transmitter, automated flight following equipment, fire extinguisher, first-aid kit, survival kit, full electrical system, engine hour meter, VHF communications radio, auxiliary cabin heat system, cabin air assembly, outside air temperature gauge, heating or deicing equipment, high visibility markings, and left-side window opening of maximum 22 inches. The pilot must hold a Commercial Pilot Certificate with instrument rating, valid first or second-class FAA medical certificate, and meet minimum flight hour requirements including 1,500 total hours, 250 hours pilot-in-command (PIC), 100 hours PIC in preceding 12 months, and 75 hours night flight time. For low-level flights, pilots require 1,200 hours PIC in single-engine land aircraft, 100 hours PIC in preceding 12 months, 100 hours PIC in aircraft type, and 250-500 hours wildlife damage management experience.

The contract is a firm, fixed-price, indefinite delivery, indefinite quantity commercial services contract with five one-year ordering periods (base period January 1, 2027–December 31, 2027, plus four option periods through December 31, 2031). The contract ceiling is $500,000 with a guaranteed minimum of $5,000. Estimated quantities include 400 flight hours per year at an unnamed hourly rate, plus travel expenses for operational (2 days at $200/day) and training (4 days at $500/day). The solicitation number is 124PSA27Q0041, with questions due by December 14, 2026, at 5:00 PM EST and quotes due by December 17, 2026, at 5:00 PM EST. Award will be made to the highest technically rated offeror with fair and reasonable pricing and acceptable or neutral past performance. The contract is subject to the Service Contract Act, and offerors must comply with wage determinations applicable to the performance location. The contractor must maintain comprehensive insurance including workers' compensation, general liability ($500,000 per occurrence), automobile liability ($200,000 per person, $500,000 per occurrence), and aircraft public and passenger liability ($200,000 per person, $500,000 per occurrence), with Public Aircraft Operations endorsement and "any airworthiness" certificate coverage. Additional requirements include Safety Management System implementation, pilot performance evaluations, annual flight reviews, accident reporting, maintenance per FAA and manufacturer specifications, and compliance with HSPD-12 security and background check requirements. The Contracting Officer is Todd K. Bierl, located at USDA APHIS, 250 Marquette Avenue, Suite 410, Minneapolis, MN 55401, telephone 612-336-3465.

View the file

Other files

File Type Posted
USDA_QASP_Fixed Wing_Flight_Services.docx DOCX document

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

SEE ADDENDUMIS CHECKED

CODE 18a. PAYMENT WILL BE MADE BY

CODE

FACILITYCODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER

OFFEROR

APHIS-MN-126395

MINNEAPOLIS MN 55401

SUITE410

250 MARQUETTE AVE

USDA APHIS

APHIS-WS-NDSD-877A CODE 16. ADMINISTERED BYCODE

X

X

488190

SIZE STANDARD:

% FOR:SET ASIDE:UNRESTRICTED ORAPHIS-MN-126395

REQUEST FOR

PROPOSAL

(RFP)

INVITATION

FOR BID (IFB)

10. THIS ACQUISITION ISCODE

REQUEST FOR

QUOTE (RFQ)

14. METHOD OF SOLICITATION

13b. RATING

NORTH AMERICAN INDUSTRY

CLASSIFICATION STANDARD

(NAICS):

SMALL BUSINESS

12/17/2026 1700 ET

11/18/2026

612-336-3465TODD BIERL

(No collect calls)

INFORMATION CALL:

FOR SOLICITATION 8. OFFER DUE DATE/LOCAL TIMEb. TELEPHONE NUMBER a. NAME

4. ORDER NUMBER3. AWARD/ 6. SOLICITATION

124PSA27Q0041

5. SOLICITATION NUMBER

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS 1. REQUISITION NUMBER PAGE OF

1 35 1178380OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

TELEPHONE NO.

17a. CONTRACTOR/

See Schedule

15. DELIVER TO

MINNEAPOLIS MN 55401

SUITE410

250 MARQUETTE AVE

9. ISSUED BY

7.

2. CONTRACT NO.

EFFECTIVE DATE

$40

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW

ISSUE DATE

DELIVERY FOR FREE ON BOARD

(FOB) DESTINATION UNLESS

BLOCK IS MARKED

11.

SEE SCHEDULEX

12. DISCOUNT TERMS THIS CONTRACT IS A RATED

ORDER UNDER THE DEFENSE

PRIORITIES AND ALLOCATIONS

SYSTEM - DPAS (15 CFR 700)

13a.

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

(SDVOSB)

HUBZONE SMALL

BUSINESS

8(A)

USDA APHIS

WOMEN-OWNED SMALL

BUSINESS (WOSB)

ECONOMICALLY DISADVANTAGED

WOMEN-OWNED SMALL

BUSINESS (EDWOSB)

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

DELIVER TO:

North Dakota/South Dakota State Off

USDA, APHIS, WS

2110 Miriam Circle Suite A Bismarck ND 58501-2502 US the required tasks and responsibilities of the Contractor providing fixed¿wing flight services in support of the North Dakota WS Programs.

Contracted flight operations primarily support (Use Reverse and/or Attach Additional Sheets as Necessary)

HEREIN, IS ACCEPTED AS TO ITEMS:

X

XX

DATED

TODD K. BIERL

. YOUR OFFER ON SOLICITATION (BLOCK 5),

INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER

ARE

ARE

31c. DATE SIGNED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA

31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or print)

ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL

SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

27a. SOLICITATION INCORPORATES BY REFERENCE (FEDERAL ACQUISITION REGULATION) FAR 52.212-1, 52.212-4. FAR 52.212-3

AND 52.212-5 ARE ATTACHED. ADDENDA

26. TOTAL AWARD AMOUNT (For Government Use Only)

OFFER

STANDARD FORM 1449 (REV. 11/2021)

Prescribed by GSA - FAR (48 CFR) 53.212

ARE NOT ATTACHED.

ARE NOT ATTACHED.

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

30b. NAME AND TITLE OF SIGNER (Type or print)

30a. SIGNATURE OF OFFEROR/CONTRACTOR

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

25. ACCOUNTING AND APPROPRIATION DATA

29. AWARD OF CONTRACT: REFERENCE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32c. DATE 32b. SIGNATURE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

40. PAID BY39. S/R VOUCHER NUMBER38. S/R ACCOUNT NUMBER

37. CHECK NUMBER

FINALPARTIAL

36. PAYMENT

FINALPARTIAL

35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER33. SHIP NUMBER

COMPLETE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

42d. TOTAL CONTAINERS42c. DATE REC'D (YY/MM/DD)

42b. RECEIVED AT (Location)

42a. RECEIVED BY (Print)

41c. DATE41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

STANDARD FORM 1449 (REV. 11/2021) BACK

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

activities related to wildlife damage management.

Additional missions may include disease monitoring, removal of invasive species, and emergency response operations. Flight requirements may fluctuate based on predation levels, operational priorities, and weather conditions; however, the Contractor must remain available to perform services with a minimum of

72 hours¿ notice.

WS may conduct operations under interagency agreements or cooperative service agreements with state and federal agencies, and private landowners. The Contractor¿s services may be utilized to support any such agreements.

The government is awarding a firm, fixed-price, indefinite delivery, indefinite quantity, commercial services contract.

The period of performance for this contract includes five ordering periods and each ordering period will be twelve (12) months in duration

Response for quote - no more than 50 pages

Questions due bu Dec 14, 2026 BY 5:00 PM EST

Quotes due by Dec 17, 2026 BY 5:00 PM EST

Continued ...

32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

35 2 of

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

NAME OF OFFEROR OR CONTRACTOR

3 35

CONTINUATION SHEET

REFERENCE NO. OF DOCUMENT BEING CONTINUED PAGE OF

(A) (B) (C) (D) (E) (F)

124PSA27Q0041

Read PWS AND QUASP!!

Awardee must be registered in SAM.GOV

Period of Performance: 01/01/2027 to 12/30/2032

0001 BASE ORDERING PERIOD Aerial flying task order for fixed wing aircraft.

Product/Service Code: F001

Product/Service Description: NATURAL

RESOURCES/CONSERVATION- AERIAL

FERTILIZATION/SPRAYING

Delivery: 12/31/2027

Period of Performance: 01/01/2027 to 12/31/2027

0002 ORDERING PERIOD 1 (one) Aerial flying task order for fixed wing aircraft.

Product/Service Code: J015

Product/Service Description: MAINT/REPAIR/REBUILD

OF EQUIPMENT- AIRCRAFT AND AIRFRAME STRUCTURAL

COMPONENTS

Delivery: 12/31/2028

Period of Performance: 01/01/2028 to 12/30/2028

0003 ORDERING PERIOD 2 (TWO) Aerial flying task order for fixed wing aircraft.

Product/Service Code: J015

Product/Service Description: MAINT/REPAIR/REBUILD

OF EQUIPMENT- AIRCRAFT AND AIRFRAME STRUCTURAL

COMPONENTS

Delivery: 12/31/2029

Period of Performance: 01/01/2029 to 12/30/2029

0004 ORDERING PERIOD 3 (THREE) Aerial flying task order for fixed wing aircraft.

Product/Service Code: J015

Product/Service Description: MAINT/REPAIR/REBUILD

OF EQUIPMENT- AIRCRAFT AND AIRFRAME STRUCTURAL

COMPONENTS

Delivery: 12/31/2030

Period of Performance: 01/01/2030 to 12/30/2030

Continued ...

NSN 7540-01-152-8067 OPTIONAL FORM 336 (4-86)

Sponsored by GSA

FAR (48 CFR) 53.110

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

NAME OF OFFEROR OR CONTRACTOR

4 35

CONTINUATION SHEET

REFERENCE NO. OF DOCUMENT BEING CONTINUED PAGE OF

(A) (B) (C) (D) (E) (F)

124PSA27Q0041

0005 ORDERING PERIOD 4 (FOUR) Aerial flying task order for fixed wing aircraft.

Product/Service Code: J015

Product/Service Description: MAINT/REPAIR/REBUILD

OF EQUIPMENT- AIRCRAFT AND AIRFRAME STRUCTURAL

COMPONENTS

Delivery: 12/31/2031

Period of Performance: 01/01/2031 to 12/30/2031

Todd K. Bierl

(Major Program Contracting Officer)

Emergency Acquisition

Marketing and Regulatory Program Business (MRPBS)

Acquisition and Asset Management Division (AAMD)

Acquisition Branch

Animal and Plant Health Inspection Service (APHIS)

Office#(612)336-3465

Cell# (612)500-1321/(763)286-8084

NSN 7540-01-152-8067 OPTIONAL FORM 336 (4-86)

Sponsored by GSA

FAR (48 CFR) 53.110

124PSA27Q0041 Fixed Wing Aircraft North Dakota 5

PART 1.0 - SCHEDULE OF ITEMS

0001 CLINs Ordering Period One: Jan 1, 2027 – Dec 31, 2027

Item No. Description of Item Unit Est. Quantity Unit Price Total Amount

0001a. Fixed Wing Flight Services HR 400 $_______ $_______

0001b. Travel Expenses (Operational) Day 2 $200.00 $400.00

0001c. Travel Expenses (Training) Day 4 $500.00 $2,000

0002 CLINs Ordering Period Two: Jan 1, 2028 – Dec 31, 2028

Item No. Description of Item Unit Est. Quantity Unit Price Total Amount

0002a. Fixed Wing Flight Services HR 400 $_______ $_______

0002b. Travel Expenses (Operational) Day 2 $200.00 $400.00

0002c. Travel Expenses (Training) Day 4 $500.00 $2,000

0003 CLINs Ordering Period Three: Jan 1, 2029 – Dec 31, 2029

Item No. Description of Item Unit Est. Quantity Unit Price Total Amount

0003a. Fixed Wing Flight Services HR 400 $_______ $_______

0003b. Travel Expenses (Operational) Day 2 $200.00 $400.00

0003c. Travel Expenses (Training) Day 4 $500.00 $2,000

0004 CLINs Ordering Period Four: Jan 1, 2030 – Dec 31, 2030

Item No. Description of Item Unit Est. Quantity Unit Price Total Amount

0004a. Fixed Wing Flight Services HR 400 $_______ $_______

124PSA27Q0041 Fixed Wing Aircraft North Dakota 6

0004b. Travel Expenses (Operational) Day 2 $200.00 $400.00

0004c. Travel Expenses (Training) Day 4 $500.00 $2,000

0005 CLINs Ordering Period Five: Jan 1, 2031 – Dec 31, 2031

Item No. Description of Item Unit Est. Quantity Unit Price Total Amount

0005a. Fixed Wing Flight Services HR 400 $_______ $_______

0005b. Travel Expenses (Operational) Day 2 $200.00 $400.00

0005c. Travel Expenses (Training) Day 4 $500.00 $2,000

CONTRACT CEILING: $500,000.00

SCHEDULE NOTES

1) The quantities as listed in the “Schedule of Items” are estimated requirements for this contract period. The Government estimates, but does not guarantee, the volume of purchases under this contract. The USDA, APHIS attempts to be as accurate as possible when providing estimated quantities, however, actual quantities required may vary from the quantities listed. Beyond the guaranteed contract minimum of $5,000.00, no guarantee is given as to the actual quantity required during the term of this contract.

2) The Department of Labor Service Contract Act applies to this contract so the contractor must take this into consideration when developing a price quote. The contractor is responsible for obtaining the wage determination applicable to the location where the services will be performed as well as determining the appropriate labor categories/occupation codes under the applicable wage determination. See section entitled “Wage Determination and Labor Rates” for further information. Please contact the contracting officer if you need assistance.

3) Travel Expenses (Operational): On occasions when flight operations occur more than 50 miles from the Contractor’s home base, a fixed daily travel rate will be paid for each individual required to travel. All travel must be approved in advance by the Contracting Officer Representative (COR). Travel will be reimbursed at the fixed rate established in the Schedule.

4) Travel Expenses (Training): On occasions when travel of more than 50 miles from the Contractor’s home base is required to complete training and performance evaluations required under this contract, a fixed daily travel rate will be paid for each individual required to travel.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 7

All travel must be approved in advance by the Contracting Officer Representative (COR).

Travel will be reimbursed at the fixed rate established in the Schedule.

PART 2.0 – PERFORMANCE WORK STATEMENT

2.1 - Scope This PWS defines the requirements for providing fixed‑wing flight services, supporting wildlife damage management operations in North Dakota, including all tasks, deliverables, and standards required for safe and compliant flight operations.

2.2 - Background The United States Department of Agriculture (USDA), Animal and Plant Health Inspection Service (APHIS), Wildlife Services (WS) Program in North Dakota require contracted fixed‑wing flight services to support their wildlife damage management and related operational missions. The Contractor must furnish, operate and maintain one fixed wing aircraft in accordance with the specifications.

2.3 - Purpose The purpose of this Performance Work Statement (PWS) is to identify the required tasks and responsibilities of the Contractor providing fixed‑wing flight services in support of the North Dakota WS Programs.

Contracted flight operations primarily support activities related to wildlife damage management.

Additional missions may include disease monitoring, removal of invasive species, and emergency response operations. Flight requirements may fluctuate based on predation levels, operational priorities, and weather conditions; however, the Contractor must remain available to perform services with a minimum of 72 hours’ notice.

WS may conduct operations under interagency agreements or cooperative service agreements with state and federal agencies, and private landowners. The Contractor’s services may be utilized to support any such agreements.

2.4 - Contract Type and Term The government is awarding a firm, fixed-price, indefinite delivery, indefinite quantity, commercial services contract.

The period of performance for this contract includes five ordering periods and each ordering period will be twelve (12) months in duration.

2.5 Limitations on Personal Services

The Government will not exercise supervision or control over Contractor personnel. Contractor personnel must perform independent, non‑personal services.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 8

2.6 - Performance Tasks

2.6.1 Objective 1: Provide Safe and Effective Fixed-Wing Flight Operations The Contractor must conduct fixed-wing flight operations to support wildlife damage management missions including predation mitigation, disease monitoring, invasive species removal, and emergency response operations. The Contractor must maintain availability with a minimum of 72 hours’ notice and conduct flights only during daylight hours and under VFR conditions. Expected outcomes include safe, efficient completion of missions and consistent aircraft and pilot readiness. All tasks must comply with the WS Aviation Safety and Operations Manual, FAA regulations, weight and balance requirements, and all applicable safety policies. The Contractor must possess and maintain all required pilot qualifications, including a Commercial Pilot Certificate with instrument rating, FAA medical certification, and required flight-hour minimums. The pilot must demonstrate proficiency in low-level flight, safe operational judgment, emotional stability, and effective communication.

2.6.2 Objective 2: Maintain Required Safety, Reporting, and Compliance Documentation The Contractor must submit accurate flight hour documentation per sortie, complete required pilot evaluations and annual flight reviews, and report all accidents, incidents, and hazards in accordance with WS and FAA requirements. Expected outcomes include timely and accurate reporting that supports program oversight, regulatory compliance, and risk management. Compliance must follow FAA reporting rules and WS Aviation Safety Manual requirements. The Contractor must possess the ability to accurately complete all reporting, documentation, and hazard/incident submissions.

2.6.3 Objective 3: Comply with Personal Protective Equipment Requirements The Contractor must wear a WS-approved aviation helmet, flight suit, gloves, and all other required protective equipment during all flight operations. Expected outcomes include full adherence to aviation PPE requirements, ensuring pilot safety and compliance with WS standards. All PPE must meet the specifications within the WS Aviation Safety and Operations Manual. The Contractor must be able to inspect, maintain, and properly wear all required PPE.

2.6.4 Objective 4: Ensure Aircraft Fueling, Handling, and Maintenance Compliance The Contractor must ensure that all fuel used meets engine manufacturer requirements and is transported, stored, and dispensed in accordance with applicable aviation standards. The Contractor is solely responsible for performing all aircraft maintenance and ensuring that the aircraft is maintained in full compliance with manufacturer instructions, FAA regulations, FAA Airworthiness Directives, and WS maintenance advisories. The Contractor must also maintain complete and accurate aircraft maintenance records, including current weight and balance data. Expected outcomes include safe, airworthy contractor‑maintained aircraft with complete, accurate, and fully compliant maintenance documentation. The Contractor must possess and apply adequate knowledge of aircraft fueling standards, maintenance documentation procedures, and all applicable regulatory requirements.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 9

2.6.5 Objective 5: Implement and Maintain a Contractor Safety Management System The Contractor must establish, implement, and maintain a Safety Management System that aligns with WS aviation safety practices and includes Safety Policy, Safety Risk Management, Safety Assurance, and Safety Promotion. The Contractor must utilize the WS Flight Risk Assessment Tool (FRAT), SAFECOM reporting, and maintain a hazard log with corrective action tracking. Expected outcomes include continuous hazard identification, effective mitigation, and integration of safety practices into all aviation operations. SMS documentation must be submitted within 30 days of award. The Contractor must possess skills in aviation SMS processes, hazard analysis, and corrective action monitoring.

2.6.6 Objective 6: Provide Operational Availability, Coordination, and Communication The Contractor must maintain readiness at designated operational bases and coordinate schedules with the Contracting Officer Representative or Contracting Officer as required.

The Contractor must notify the Contracting Officer when reaching 80 percent of the task order funding limit. Expected outcomes include consistent operational availability and effective coordination with Government personnel. The Contractor must have strong communication skills and the ability to operate in variable schedules and remote locations.

2.6.7 Objective 7: Meet Security, Background, and Eligibility Requirements The Contractor must complete all required background checks, identity verification, and adherence to personnel eligibility requirements, including citizenship and lawful permanent resident status where applicable. Expected outcomes include ensuring that only vetted, eligible personnel support contract performance. Compliance must follow HSPD-12, FIPS 201, and applicable federal security requirements. The Contractor must have the capability to successfully undergo federal background processes and complete internal pre-screening prior to Government submission.

2.7 - Deliverable Schedule

Key Deliverables Item No.

Deliverable / Item Title

Description Frequency Reference Delivery Format

Due By

1 Pilot Services Report

Report of recorded flight hours

Per sortie Ref. PWS Section 2.18, Recording and Payment of Services

Via IPP invoice

No more frequently than every two weeks

2 Annual Pilot Qualification Verification Report

Report verifying compliance with PWS Section 2.8.6 and 2.15.6

Annually Ref. PWS Section 2.15.6, Inspection of Key Personnel

Via email to COR

Prior to start of ordering period flight operations

3 Safety Management System Documentation and Updates

Initial SMS plan plus updates, revisions, hazard logs, and safety date required

Initial submission within 30 days of award;

update as

Ref. PWS Section 2.22 Contractor Safety Management System (SMS)

Via email to COR and SASI

30 days after award;

Updates: As required

124PSA27Q0041 Fixed Wing Aircraft North Dakota 10 under contractor’s

SMS

required or upon Government request

2.8 - Performance Requirements

2.8.1 - Airplane Specifications The airplane must be a Piper PA18, Cub Crafter CC 18, or X-Cub

• The airplane and all accessories must be in an operable condition and present a neat and clean appearance

• Upholstery, paint, and plexiglass must be in good condition

• Minimum seating capacity: pilot and one WS/cooperator qualified non-crewmember

2.8.2 - Airplane Equipment Requirements

• Dual controls must be installed for flights flown with the purpose of flight training, check rides and evaluation flights. If a firearm is required for the training, check ride or evaluation, the flight instructor training officer/check airmen may remove the dual controls at his/her discretion; and

• WS personnel must not operate an aircraft unless it is equipped with operational intercommunication system including handsets, headsets, microphones, and selector switches. Each aircraft must provide a means of two-way communication between the pilot and gunner or other qualified non-crewmember that is capable of "hands free" operation; and

• Lap belt and double strap shoulder restraints with inertial reel must be present in front and rear seats for the airplane. Lap belts and shoulder straps must fasten with one single‑point quick‑release mechanism; and

• FAA approved ELT of the automatic deployable or automatic fixed type meeting the latest technical standard order. The ELT unit must be attached to the aircraft as far aft as possible in accordance with FARs; and

• Operational Automated Flight Following equipment approved by the NAC; and

• An approved fire extinguisher, a first-aid kit, and survival kit; and

• Full electrical system including generator or alternator, battery, and starter

(airplane); and

• Engine hour meter, recording in hours and tenths or hours and hundredths and activated by an engine oil pressure switch to record engine running time (airplane only); and

• Very High Frequency (VHF) communications radio and radio capable of communicating with ground crews; and

• Auxiliary cabin heat system; and

• Cabin air assembly; and

• Outside air temperature gauge; and

• Personnel access step for each door if extended height gear is installed; and

124PSA27Q0041 Fixed Wing Aircraft North Dakota 11

• Heating or deicing equipment for each carburetor or, for a pressure carburetor, an alternate air source (airplane); and

• USDA will provide a portable flight following system that must be used during all operations; and

• High wing; two-place, tandem seating; and

• Conventional landing gear (with tail wheel); and

• Single-engine, minimum 150 horsepower; and

• Maneuverable with short takeoff and landing characteristics; and

• Left side window with a maximum 22 inch opening capable of being locked open in flight to provide adequate angle of fire for the gunner (shooting must be accomplished from the left side of the aircraft); and

• Removable rear seat control stick (dual controls must be removed except during approved training flights); and

• Adequate protection for control mechanisms (front and rear) and under seat area to prevent foreign objects (ejected shells, etc.), from interfering with control movement; and

• Protection for, or removal of, rear seat throttle quadrant, to prevent interference with the operation of the throttle by the gunner or other qualified non-crewmember;

and

• High visibility markings as follows:

o Outer 4" of face rear side of one blade of propeller; and o Forward Leading edge of wing struts and jury strut on shooting side; and o High visibility markings should be of a color that must be visible against the terrain over which the mission is flown. Change of background color during seasonal differences must be considered. Tape may be used on leading edges of wing struts. Paint must be used on the propeller.

• Firearm must eject out of the same side of the aircraft that gunning operations are occurring from.

• The following equipment is desirable and may be required by the State Director:

o 82" diameter propeller (PA18 Supplemental Type Certificate 11-

SA279AL) or equivalent.

o Oversize main wheel tires (Tundra tires).

o Built up cushions for either front or rear seat.

o Extended landing gear.

o Extended skylight.

o Flagger.

2.8.3 - Substitution of Aircraft The Contractor may substitute aircraft during performance of the contract, provided such substitution meets all requirements herein and is approved in writing by the Contracting Officer or his/her authorized representative. Request for substitution must be made at least 10 days prior to exchange except for unforeseen conditions. Transportation of substituted aircraft to the point of use will be at the Contractor’s expense.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 12

2.8.4 - Search and Rescue Missions (SAR) WS aircraft may be used for SAR missions being conducted by a government agency (i.e., a city, county, state, or tribal law enforcement agency), the Civil Air Patrol (if a search is authorized by the U.S. Air Force Search & Rescue Coordination Center), or the U.S. military, because of life threatening situations. SAR mission requirements are in accordance with the WS Aviation Safety and Operations Manual.

2.8.5 - Pilot Requirements The pilot must be qualified in accordance with WS aviation operations and training policies included in the Wildlife Services Aviation Safety and Operations Manual, in addition to the requirements herein.

2.8.6 - Pilot Qualifications

• Valid and current Commercial Pilot Certificate

• Instrument Pilot Rating

• Valid First-class or second-class FAA medical certificate

• Must pass required background check

• Pilots must meet the following minimum requirements:

o 1,500 hours total flight time o 250 hours Pilot In Command (PIC) flight time o 100 hours PIC flight time in the preceding 12 months o 75 hours of night flight time

• Pilots who will perform low level flights must also meet the following additional requirements:

o 1200 hours PIC flight time in Single Engine Land airplane; and o 100 hours PIC flight time in the preceding 12 months; and o 100 hours PIC flight time in the make and model of aircraft or similar type, to be used on WS missions; and 250 hours flight experience as PIC for wildlife damage management operations; or 500 hours flight experience in WS type flying.

2.8.7 - Pilot Authority and Responsibility The pilot is responsible for the safe operation of the aircraft and the safety of its occupants. Safety requirements, such as preflight, reserve fuel, and weight and balance limitations must be strictly adhered to. The pilot must refuse any flight or landing which the pilot considers hazardous or unsafe.

Pilots must not permit any passengers to ride in the aircraft or any cargo to be loaded therein unless authorized by COR and meeting the standards of a qualified non-crewmember for Public Aircraft Operations.

Pilot must demonstrate the following:

i. Flying safety attitudes and habits.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 13

ii. Positive attitude regarding requirements and procedures for aerial hunting.

iii. Emotional stability under the stress of low-level aircraft operations required for aerial hunting.

iv. Positive personality characteristics required to work and communicate effectively with field personnel and cooperators.

v. Knowledge of and/or willingness to learn predator habits and how to effectively and efficiently aerial hunt.

vi. Ability to safely identify and maintain effective airborne contact with the target animal

vii. Willingness to work unusual hours

Pilot is limited to flying during daylight hours and under VFR conditions only. Ferry flights to and from low level flights may be flown from one hour prior to sunrise until one hour after sunset if there is a visible horizon.

2.8.8 - Flight Time/Duty Time Limitations for Aircrew Members Flight crews must not exceed the following flight time and crew duty time limitations:

• Maximum of 8 hours flight time per duty period for a single-pilot crew

• Maximum crew duty period including flight and standby time of 12 hours in any

24-hour period. At least 12 consecutive hours of rest will be required prior to each duty period during each 24-hour period.

• Maximum of 40 hours flight time during any consecutive 6-day period. This 6-day flight time limitation may be temporarily exceeded during emergency life saving situations, or for unscheduled enroute delays due to weather conditions. When a pilot or crew acquires the maximum number of flight hours in a consecutive 6-day period, he/they must have the following 24-hour period off-duty, and a new 6-day cycle will begin. The 40-hour limitation must apply to any combination of flight time and performance of mechanical duties for which the pilot may be certified.

• The Government may further restrict daily flight hour limitations. Pilots may also be removed from duty for fatigue or other causes before reaching their flight hour or duty limitations.

• All pilot flying time, including both directed flights under this contract and for the pilot’s other activities (charter, instruction, etc.) will be cumulative and subject to the pilot time and duty time limitations of this contract. Pilots exceeding these limitations may be temporarily or permanently suspended from further flights on this contract.

2.8.9 - Availability of Mechanic The Contractor must ensure that a qualified mechanic is available to report to the designated base or alternate base within 6 hours from the time mechanical services are required, in order to prevent disruption to flight operations.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 14

2.9 - Personal Protective Equipment (PPE) For low-level flights, Pilots must provide and wear an aviator’s protective helmet equipped with microphone and headset compatible with radio specifications of this contract. The helmet must be equipped with a chin strap and must be individually fitted to cover the head, back of the neck and ears. Flights helmets must meet the specifications within WS Aviation Safety and Operations Manual.

For all flights, Pilots must provide and wear a long-sleeved shirt and trousers (or long-sleeved flight suit) made of fire-resistant polyamide or aramid material or equal. Pilots must provide and wear leather or polyamide or aramid gloves. The shirt, trousers, boots, and gloves must overlap to prevent exposure to flash burns.

2.10 - Permits and Licenses The Contractor must be responsible for obtaining, at their expense, all necessary permits and licenses to comply with all applicable Federal, State, and local laws and regulations.

2.11 - Government-Furnished Property USDA-WS will provide the following government property to the Contractor for use in the performance of this contract.

i. Portable flight following equipment

ii. WS Manuals

2.12- Fuel, Oil and Lubricants

i. The Contractor must ensure all fuel used by aircraft is approved for use by the engine manufacturer and must be a petroleum product designed for use in aircraft.

ii. The Contractor must ensure all fuels are manufactured, transported, stored and dispensed in strict accordance with procedures formulated for aviation fuel standards.

iii. Fuels, lubricating oils and hydraulic fluids used to maintain the airplane must be supplied by the Contractor.

iv. Fueling operations must comply with the manufacturer's standards.

v. Maintenance of fuel storage and fueling facilities is the Contractor’s responsibility.

vi. Airplanes must not be refueled while the engine is running.

2.13 - Flight Operations Flight operations will be conducted in strict compliance with the WS Safety and Operations Manual, the WS Aviation Safety Program Policies, the Federal Aviation Regulations, and any applicable local laws.

2.14 - Government Roles and Responsibility The Contracting Officer will designate a Contracting Officer Representative (COR) to work with the Contractor to coordinate all aspects of this contract.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 15

2.15 - Contractor Key Personnel

2.15.1 Key Personnel Designation

The Contractor must designate the Pilot(s) performing services under this contract as Key Personnel due to the critical nature of aviation operations and the mission-essential skills required for wildlife damage management flight missions. Key Personnel are those individuals whose qualifications, experience, and performance are essential to successful contract execution.

2.15.2 Approval and Substitution of Key Personnel

The Contractor must identify all proposed Key Personnel in their offer, including full name, licenses, certifications, flight hour documentation, and all other information necessary to verify compliance with the pilot qualification requirements.

No substitutions of Key Personnel may be made without prior written approval from the Contracting Officer. Requests for substitution must include:

• Reason for the requested change;

• Full qualification package for the proposed replacement;

• Confirmation that the replacement meets or exceeds all performance, safety, and flight-hour requirements contained in this PWS.

The Contracting Officer reserves the right to reject any proposed replacement who does not meet qualification standards or whose experience is deemed insufficient for safe and effective mission performance.

2.15.3 Temporary Absences

In the event of short-term, temporary absences (e.g., illness, personal emergency), the Contractor must notify the COR as soon as practicable. If the absence exceeds five (5) consecutive business days, the Contractor must either provide a qualified substitute pilot for Contracting Officer approval or suspend flight operations until Key Personnel availability is restored. The Government is under no obligation to accept unapproved personnel.

2.15.4 Performance of Key Personnel

Key Personnel must maintain the performance, safety, and conduct standards required in the PWS at all times, including:

• Compliance with flight-hour and medical requirements (Section 2.5.2);

• Compliance with WS Aviation Safety and Operations Manual;

• Demonstrated safe decision-making, emotional stability, and professionalism;

• Ability to work effectively with WS crews, cooperators, and Government personnel.

If Key Personnel performance becomes unacceptable or unsafe, the CO may require their removal and replacement at no additional cost to the Government.

2.15.5 Continuity of Operations

The Contractor must maintain adequate staffing and internal planning to ensure continuity of operations in case of resignation, removal, or extended unavailability of Key Personnel.

Delays in performance due to failure to provide qualified Key Personnel will be considered a

124PSA27Q0041 Fixed Wing Aircraft North Dakota 16

Contractor performance issue and may affect past performance evaluations, payment, or continuation of work.

2.15.6 Inspection of Key Personnel

Upon request, Contractor must promptly submit completed pilot information forms.

Information from these forms will be used in evaluating the pilot's qualifications. Only those individuals whose previous experience can be verified will be considered for use under this contract.

Prior to commencing flight operations under this contract, all pilots must complete a pilot performance evaluation for carding in accordance with the Wildlife Services Aviation Safety and Operations Manual. This performance evaluation may be conducted by a Wildlife Services check airman or contractor at the expense of the Government. The aircraft used for the evaluation will be the same type and model utilized for operations under this contract.

Location of the evaluation flights should include access to terrain similar to that to be flown during the contract period when possible.

Pilots under this contract must complete an annual flight review consisting of a minimum of the base tasks (1000 series) and mission task (2000 series) as outlined in the WS Airmen Certification Standards.

2.16 - Inspection of Aircraft Prior to commencing flight operations under this contract, all aircraft must be presented for inspection in accordance with the Wildlife Services Aviation Safety and Operations Manual.

The Contractor must make its aircraft available for inspection at the designated base of operations or other location acceptable to the Government at a mutually agreed upon time not later than 24 hours prior to commencing flight operations under this contract. At the time of inspection the aircraft must be properly certified and registered by the FAA and comply with all specifications set forth herein.

If the aircraft meets all requirements, an Aircraft Data Card (APHIS Form 150) authorizing use of the equipment will be issued by the Contracting Officer or his/her designated representative.

The Aircraft Data Card must be with the aircraft at all times.

The Contractor must supply at the time of the initial aircraft inspection a list of all items installed on the aircraft which are required to be overhauled or replaced on a specified time basis. This list must include the component names, serial numbers, service life (or inspection/overhaul time), total time since major inspection.

The Contractor will not be charged for the inspection required to issue or renew the Aircraft Data Card. Any additional re‑inspection made necessary due to Contractor negligence or oversight will be at the Contractor’s expense.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 17

2.17- Availability of Service The Contractor must perform required flight services at the designated base as required by the Contracting Officer or COR. The schedule of operations will be planned by the Government with the cooperation of Contractor personnel. The Government may order flight services on any day during daylight hours, depending upon the necessity of the work and suitability of flying conditions. Daylight hours are defined as between ½ hour before sunrise to ½ hour after sunset.

2.18 - Recording and Payment of Services

i. All services received will be submitted for payment in IPP.

ii. Airplane flight time will be paid from the time the airplane lifts off the ground for a direct flight until it lands.

iii. Flight time will be recorded in hours and tenths by means of an engine hour recorder activated to record flight time only.

iv. Payment must be made only for flight time ordered by the Contracting Officer or COR.

Payment will be made to the nearest tenth of an hour of actual flight time. No charge will be allowed for taxes from which the USDA is exempt.

v. Whenever WS is required to cancel or change a pre-scheduled flight on short notice, no charge must be made unless the airplane is already airborne from the airplane home base at the time of notification.

2.19 - Accident Reporting and Investigation In the event of an incident or accident involving the aircraft, the pilot, if able, must notify the respective WS supervisor and the National Aviation Coordinator (NAC) as soon as practical. An incident report must be submitted to the NAC. Other reporting provisions provided in the WS Aviation Safety Manual will be submitted in a timely manner.

The Contractor must maintain an accurate record of all aircraft accidents, incidents and injuries to all personnel involved while performing under this contract and must immediately notify the National Aviation Coordinator of all such accidents, incidents or injuries. Contractor is not permitted to remove or alter the aircraft following an accident. Contractor must make available all flight records and any equipment (damaged or undamaged) deemed necessary by the Accident Investigation Board to determine what factors caused the incident/accident.

The Contractor will be responsible for all costs associated with the disassembly of any aircraft, aircraft engine, or equipment that is necessary to determine the probable cause of any accident or incident.

Post-accident drug and alcohol testing will be in accordance with the FAA’s drug and alcohol testing regulation (14 CFR part 120) for individuals certificated under parts 61 and 63. All drug and alcohol testing results must be made available to the Government upon completion. Payment for required drug and alcohol testing will be coordinated through the applicable State Director’s office with the Government paying for the testing on a Government Purchase Card.

2.20- Rescue and Salvage Responsibilities The Contractor will be responsible for rescue operations of the Government and Contractor’s personnel employed under this contract.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 18

Salvage of damaged or demolished airplanes will be done at the Contractor’s expense. No equipment or personnel performing under this contract may be used on such operations unless authorized by the Government.

2.21 - Liabilities of The Contractor and The Government The Government will not assume any responsibility for loss or damage to equipment owned or operated by the Contractor, his agents, employees or sub-Contractors. The Government will not assume any responsibility for injury or death of the pilot, his agents, employees or sub- Contractors, caused during the performance of the contract. The Contractor will be responsible for the intentional negligent and wrongful acts or omissions of the pilot, his agents, employees or sub-Contractors and employees and agents of the sub-Contractors incidental to the performance of this contract.

The Contractor will hold and save the Government, its officers and employees harmless from all liability for any death or damage to all persons, (other than the liability of the Government to USDA employees as provided for under the Federal Employees Compensation Act) real property or personal property which results from the operation of, or incident to, equipment furnished by the contract, or otherwise incidental to performance of the agreement. However, the Contractor will not be responsible for any intentional negligent or wrongful acts of omissions of Wildlife Services employees.

During the period of performance of the contract, certain Government Furnished Equipment (GFE) may be assigned to the Contractor, (e.g. flight following device). If any GFE is lost, damaged or destroyed as a result of the Contractor’s negligence, or as a result of any accident, the fair market value of the equipment will be charged to the Contractor and withheld from payments due under this contract.

2.22- Contractor Safety Management System (SMS)

2.22.1 Requirement. The Contractor must establish, implement, and maintain its own Safety Management System (SMS) covering all aviation activities performed under this contract. The Contractor’s SMS must, at a minimum, include Safety Policy, Safety Risk Management, Safety Assurance, and Safety Promotion processes and be compatible with Wildlife Services (WS) aviation safety practices.

2.22.2 Alignment. The Contractor’s SMS must integrate applicable WS procedures and tools for missions performed under this contract, including use of the WS Flight Risk Assessment Tool (FRAT) and SAFECOM hazard/incident reporting, as directed by the Supervisory Airworthiness Safety Inspector (SASI).

2.22.3 Submission and Acceptance. Within 30 calendar days of award (or prior to flight operations, whichever is earlier), the Contractor must submit its SMS documentation (policy, procedures, reporting, assurance, and training) to the SASI for review of alignment. The Government’s review confirms compatibility with WS practices and does not relieve the Contractor of responsibility for safety performance.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 19

2.22.4 Reporting and Notifications. The Contractor must:

(a) Report aviation hazards and incidents via SAFECOM and the Contractor’s internal system;

(b) Provide immediate notification to the COR of any accident/incident affecting a WS mission, followed by written reporting to the SASI and Contracting Officer (CO).

2.22.5 Corrective Actions and Data Sharing. The Contractor must maintain a hazard log, track corrective actions, and share relevant safety data/trends with WS upon request to support mission risk management.

2.22.6 Training and Competency. The Contractor must document and maintain safety training and qualifications commensurate with the Contractor’s roles and aircraft operated under this contract.

2.22.7 Sub-Contractors. The Contractor must flow down these SMS requirements to all aviation sub-Contractors performing under this contract.

2.22.8 Enforcement. Failure to maintain and operate an effective, WS‑aligned SMS constitutes a material breach and may result in suspension of flight activities, withholding of payments, or termination, in addition to other remedies.

2.23 - Maintenance Requirements The aircraft must be fully maintained by the Contractor. If maintenance is required at locations other than the Contractor’s home base, the Contractor must provide appropriate maintenance support, equipment and personnel necessary to repair the aircraft. Transportation of maintenance personnel and equipment must be provided by the Contractor at no additional cost to the Government.

Aircraft must be operated and maintained in accordance with all manufacturers’ specifications and applicable APHIS regulations

All maintenance deficiencies existing prior to the contract must be corrected prior to performance under this contract Those deficiencies occurring during the period of performance must be corrected during normal scheduled maintenance.

All applicable manufacturer’s mandatory bulletins and FAA Airworthiness Directives and WS maintenance advisories and alerts must be complied with prior to performance under this contract. Bulletins or Airworthiness Directives published during the contract must be complied with in accordance with the individual bulletin or directive.

The Contractor must assure that all maintenance performed on aircraft is recorded in the affected aircraft’s maintenance record in accordance with FAR 43 and FAR 91. In addition to aircraft time-in-service, the hour meter reading must be recorded for all maintenance record entries.

124PSA27Q0041 Fixed Wing Aircraft North Dakota 20

A copy of the aircraft’s current maintenance record, containing as a minimum the information required by FAR 91.417, must be kept at the designated base.

The Contractor must immediately notify the Contracting Officer or COR of any proposed change of any engine, power train, flight control, or major airframe.

A test flight must be performed at the Contractor’s expense following overhaul, or replacement of any engine, propeller, major component, or flight control equipment, and following any adjustment of the flight control system before the aircraft resumes service under this purchase order. The result of the test flight must be logged in the aircraft records by the pilot.

The aircraft’s required weight and balance data must current and updated following any major repair or major alteration or change to the equipment list which affects the center of gravity of the aircraft.

The aircraft’s static system, transponder and encoding altimeters system must be maintained in accordance with the requirements of FAR 91.215.

The aircraft must have the maximum available time remaining before any scheduled or required inspections at the start of the contract. The aircraft engine and all time‑change components must each have no less than 400 hours remaining. If the engine has fewer than 400 hours remaining, the Contractor must provide documented proof of availability of a replacement engine to the Contracting Officer or COR.

For engines, propellers, and appliances, the Contractor must ensure that all maintenance performed on aircraft is recorded in the aircraft maintenance records in accordance with FAR Part 135, FAR Part 91, and FAR Part 43 as applicable.

2.24 - Task Orders

i. Government funding will be obligated to the contract by task order. The fixed hourly rate for flight services will be listed and a total not to exceed contract amount will be included.

ii. The Contracting Officer may provide funding under this contract obligating funds for the procurement of flying hours prior to the Government needing delivery of said ordered quantities.

iii. The COR will be allowed to coordinate services and schedule specific performance dates and quantities up to, but not exceeding, the total quantity authorized by the Contracting Officer.

iv. The Contractor must inform the Contracting Officer if the task order reaches 80% of the total not to exceed contract amount.

2.25 - Invoices and Payment Information

i. USDA uses the Invoice Processing Platform (IPP) for electronic submission and tracking of invoices and payment information to its suppliers of goods and services. Invoices must be submitted electronically to the IPP invoicing system. Additional information is available at www.ipp.gov.

http://www.ipp.gov/

124PSA27Q0041 Fixed Wing Aircraft North Dakota 21

ii. Invoices must be prepared in accordance with 52.212-4 (g) and must be supported with a sum of the actual flight service hours performed.

iii. Credit card purchases are allowed under this contract. The USDA Contracting Officer will provide the names of individuals authorized to make credit card purchases under this contract. The authorization will be in the form of written verification via email.

2.26- Wage Determination and Labor Rates The Department of Labor Service Contract Act applies to this contract. Task orders will specify the applicable wage determination for the ordering period.

The Contractor will be responsible for obtaining the proper wage determination for the location where the work will be performed. The SCA wage determinations can be found at www.sam.gov. Please contact the contracting officer if you need assistance in obtaining the wage determination.

2.27- Safety and Security Requirements The Homeland Security Presidential Directive-12 (HSPD-12), dated August 27, 2004, requires the development and agency implementation of a mandatory Government-wide standard for secure and reliable forms of identification for Federal employees and Contractors, including Contractor employees. As directed by HSPD-12, on February 25, 2005, the Department of Commerce issued FIPS PUB 201, which is a federal standard for secure and reliable personal identity verification (PIV) for routine physical access to Federally controlled facilities or information systems. Office of Management and Budget (OMB) memorandum M-05-24 dated August 5, 2005, provides instructions for implementing HSPD-12 according to FIPS PUB 201, and M-08¬01, dated October 23, 2007, reminds all parties that a background investigation is required.

48 CFR 3052.204-71 requires each individual employed under a federal contract to be a citizen of the United States of America, or a non-U.S. citizen who has been lawfully admitted for permanent residence as evidence by a Permanent Resident Card (USCIS I-551).

Contractor’s must…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .