11410-01000AW.pdf

Technical Data Sheet

Field Master Pro™ High-Performance RF Spectrum Analyzer

MS2090A

9 kHz to 9 GHz, 14 GHz, 20 GHz, 26.5 GHz, 32 GHz, 43.5 GHz, 54 GHz

Field Master Pro Technical Data

2 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Introduction Anritsu is proud to introduce the world’s most advanced handheld spectrum analyzer with real-time spectrum analysis capability. With frequency coverage up to 54 GHz, the new Field Master Pro™ MS2090A completely redefines the standards for portable handheld analyzers, setting another new industry benchmark for performance and accuracy. The new MS2090A is the culmination of over 60 years of microwave test and measurement equipment development, using the very latest technologies to deliver accuracy and precision in measurements previously reserved only for benchtop instruments.

Instrument Highlights

Capabilities and Functional Highlights

• Modu lation Bandwidth: up to 150 MHz

• Dynamic Range: > 106 dB in 1 Hz RBW

• DANL: –164 dBm in 1 Hz RBW

• Phase Noise: –106 dBc/Hz @ 10 kHz offset at 1 GHz

• Resolution Bandwidth (RBW): 1 Hz up to 10 MHz

• RTSA with 2.05 µs POI

• Full-band Preamplifiers

• Operation to +55 ºC: Full Performance on AC or Battery

• GNSS (GPS, GLONASS, Galileo, BeiDou)

• USB 3.0

• 10.1" Capacitive Touchscreen

• Two Hour Battery

• 5GNR FDD and TDD Analyzer

• Real-Time Spectrum Analyzer

• LTE FDD and TDD Analyzer

• WCDMA FDD Analyzer

• Spectrogram

• Zero Span IF Output

• Gated Sweep

• IQ Waveform Capture/Streaming

• Pulse Profile Measurements

• AM/FM Audio Demodulation

• Multi-language Support

• Electromagnetic Field (EMF) Measurements

• EIRP

• Field Strength

• Occupied Bandwidth

• Channel Power

• Adjacent Channel Power

• Spectral Emissions Mask

• Signal Strength and RSSI

• Carrier Aggregation

• Carrier-to-Interference

• Channel Scanner

• Total Harmonic Distortion (THD)

• Coverage Mapping measurements in

SPA, 5GNR and LTE applications

• Trace Recording/Playback

• Hi Accuracy Power Measurements

(external sensor sold separately)

• Cable and Antenna Analyzer

• Time Domain Reflectometry (TDR) measurements (Ohm/Linear)

• Interference Finder

• Interference Analysis

• Built-in PDF Report Generator

Technical Data Field Master Pro

MS2090A TDS PN: 11410-01000 Rev. AW 3 of 40

234.89

313.42

98.23

36.04

56.04 76.04

102.54 129.54

31.00

58.17

94.56

158.54

56.27

SMA CONNECTOR 6X

Dimensions in mm

USB A (2)

"N", "K", "V"

CONNECTOR

KENSIGNTON

LOCK

34.89 32.42

36.59

35.82 33.42 31.94

164.63

18.75 33.77

51.91 71.94

91.07

109.70

USB C

USB A

ETHERNET

HEADPHONE

JACK

DC POWER

MICRO SD

DATA OUT

MS2090A MA25424A

128.30

33.43

18.63

57.32 35.49

50 PINS MDR

CONNECTOR, 2X

10.01

18.63 57.32

18.40

35.49 14.61

17.44

DATA OUT

CONNECTOR

85.46

3.40

4 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Table of Contents Introduction Definitions Spectrum Analyzer Performance Spectrum Analyzer Features Real-Time Spectrum Analyzer (Option 199) Secure Data Operation (Option 7) Secure Communication (Option 17) High Accuracy Power Meter (Option 19) Interference Finder and AM/FM Audio Demodulation (Option 24) Channel Scanner (Option 27) GNSS Receiver (Option 31) Zero Span IF Output (Option 89) Gated Sweep (Option 90) IQ Waveform Capture (Option 124/126) IQ Waveform Streaming (Option 125/127) Cable and Antenna Analyzer (Option 331) Time Domain Reflectometry (TDR) Measurement (Option 3) Pulse Analyzer (Option 421) Coverage Mapping (Option 431) Electromagnetic Field (EMF) Measurement (Option 444) Electromagnetic Field (EMF) Meter (Option 445) AM/FM Modulation Measurement (Option 509) WCDMA FDD Signal Analyzer (Option 871) LTE FDD/TDD Signal Analyzer (Option 883) 5GNR FDD/TDD Signal Analyzer (Option 888) General Specifications Programmable Remote Control MA25101A IQ Streaming PCIe Kit Anritsu Remote and Report Tools (ARRT) Ordering Information – Instrument Options Standard Accessories Related Manuals USB Sensors and Power Indicator Optional Accessories

Definitions Specifications All specifications and characteristics apply to Revision 4 instruments under the following conditions, unless otherwise stated:

• Over the 25 ± 5 ºC temperature range.

• After 10 minutes of warm-up time, where the instrument is left in the ON state.

• When using internal reference signal.

Typical Performance Typical specifications are not tested and are not warranted. They are generally representative of characteristic performance.

Nominal Performance Nominal specifications are design parameters; they are not tested and are not warranted.

Time Base Error Input Frequency × Frequency Reference Error.

Calibration Cycle Calibration is within the recommended 12 month period.

All specifications in this data sheet are subject to change without notice. For the most current data sheet, please visit the Anritsu web site: www.anritsu.com.

http://www.anritsu.com

MS2090A TDS PN: 11410-01000 Rev. AW 5 of 40

Spectrum Analyzer Performance

Frequency (usable to 0 Hz) MS2090A-0709 9 kHz to 9 GHz (Option 709) MS2090A-0714 9 kHz to 14 GHz (Option 714) MS2090A-0720 9 kHz to 20 GHz (Option 720) MS2090A-0726 9 kHz to 26.5 GHz (Option 726) MS2090A-0732 9 kHz to 32 GHz (Option 732) MS2090A-0743 9 kHz to 43.5 GHz (Option 743) MS2090A-0754 9 kHz to 54 GHz (Option 754)

Tuning Resolution 1 Hz Span 10 Hz to max frequency, Zero Span

Frequency Reference Internal, GNSS, External Internal Frequency Reference Aging: ± 1.0 x 10–6 per 10 years

Accuracy: ± 3.0 x 10–7 (–10 °C to 55 °C) plus aging (see “GNSS Receiver (Option 31)” on page 11 for improved accuracy)

External Frequency Reference 10 MHz, -10 dBm to +10 dBm

Bandwidth Analysis Bandwidth 22 MHz (standard), 55 MHz (Option 103), 120 MHz (Option 104), 150 MHz (Option 105)

RTSA Bandwidth 22 MHz (standard), 55 MHz (Option 103), 120 MHz (Option 104), 150 MHz (Option 105) Resolution Bandwidth (RBW) 1 Hz to 10 MHz (in RTSA, minimum RBW varies by span, max is 40 MHz), 1 Hz to 40 MHz in zero span

RBW Selectivity 4:1 nominal (–60 dB / –3 dB) Video Bandwidth (VBW) 0.1 Hz to 10 MHz, 1 Hz to 40 MHz in zero span

CISPR Bandwidth Resolution bandwidth when using Quasi-Peak marker function: 200 Hz, 9 kHz, and 120 kHz VBW/Average Type Linear/Log

Sweep Manual Sweep Maximum sweep time is 3600 s (1 hour)

Sweep Points 10 to 10,001 (1001 in zero span) Sweep Rate (non-zero span) 40 GHz/s typical (full span, RBW = VBW = 3 MHz)

Zero Span Sweep Time 60 ns to 3600 s in zero span

Sweep Time Accuracy ±2 % in zero span

Spectral Purity – SSB Phase Noise

Spurs (0 dB input attenuation)

Amplitude Ranges Dynamic Range >106 dB minimum at 2.4 GHz, 2/3 (TOI-DANL) in 1 Hz RBW

Measurement Range DANL to +30 dBm Display Range 1 to 15 dB/div in 1 dB steps, ten divisions displayed

Reference Level Range –150 dBm to +30 dBm Attenuator Resolution 0 to 65 dB, 5 dB steps Reference Level Offset 99.9 dB external loss to 99.9 dB external gain

Maximum Continuous Input +30 dBm peak typical, ± 50 VDC (≥ 10 dB attenuation) +23 dBm peak typical, ± 50 VDC (< 10 dB attenuation) +10 dBm peak typical, ± 50 VDC (preamp = On)

Offset from 1 GHz 10 kHz

100 kHz 1 MHz

10 MHz

Maximum –102 dBc/Hz –106 dBc/Hz –111 dBc/Hz –123 dBc/Hz

Typical –106 dBc/Hz –110 dBc/Hz –116 dBc/Hz –129 dBc/Hz

Residual Spurs (RF input terminated) < 14 GHz

14 to 20 GHz > 20 to 32 GHz > 32 to 54 GHz

Preamp = Off –90 dBm, maximum –85 dBm, maximum –80 dBm, maximum –80 dBm, maximum

Preamp = On –100 dBm, maximum –100 dBm, maximum –100 dBm, maximum –95 dBm, maximum

Input-Related Spurious (–30 dBm input) Typical –60 dBc

6 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Amplitude Accuracy (10 dB attenuation, -50 dBm ≤ input signal ≤ -10 dBm, 1 kHz RBW, auto-coupled, excluding effects of VSWR, noise, and spurs)

Amplitude Linearity (input level -20 dBm to -100 dBm, reference level -20 dBm, input Attenuation 0 dB, Preamp Off, RBW 100 Hz) ± 0.1 dB Typical

Displayed Average Noise Level (DANL) (RMS detection, VBW/Avg type = Log, reference level = –20 dBm for preamp Off and –50 dBm for preamp On, auto attenuation On)

Third-Order Intercept (TOI) (–20 dBm tones 2 MHz apart, 0 dB input attenuation, preamp OFF, reference level –20 dBm)

2.4 GHz +14 dBm minimum

50 MHz to < 9 GHz +15 dBm typical 9 GHz to 20 GHz +20 dBm typical

> 20 GHz to 32 GHz +11 dBm typical > 32 GHz to 54 GHz +15 dBm typical

P1dB (nominal) < 4 GHz +5 dBm

4 GHz to 20 GHz +12 dBm > 20 GHz to 32 GHz +7 dBm > 32 GHz to 54 GHz +12 dBm

Second Harmonic Distortion (0 dB input attenuation, –30 dBm input) 50 MHz –75 dBc maximum

< 10 GHz –80 dBc typical ≥ 10 GHz –75 dBc typical

VSWR (≥ 10 dB input attenuation) < 20 GHz 1.5:1 typical

20 GHz to 54 GHz 2.0:1 typical

20 °C to 30 °C (after 30 minute warm-up) –10 °C to 55 °C (after 60 minute warm-up) 9 GHz to 20 GHz Instruments Maximum Typical Maximum Typical

9 kHz to 14 GHz > 14 GHz to 18 GHz > 18 GHz to 20 GHz

± 1.3 dB ± 1.3 dB

± 0.5 dB ± 0.5 dB ± 1.0 dB

± 2.0 dB ± 2.0 dB

± 0.5 dB ± 0.5 dB ± 1.0 dB

26.5 GHz to 54 GHz Instruments

9 kHz to 14 GHz

> 14 GHz to 20 GHz > 20 GHz to 43.5 GHz > 43.5 GHz to 54 GHz

± 1.3 dB ± 1.3 dB ± 1.8 dB ± 1.8 dB

± 0.5 dB ± 0.5 dB ± 0.5 dB ± 0.5 dB

± 2.0 dB ± 2.0 dB ± 2.5 dB ± 2.5 dB

± 0.5 dB ± 0.5 dB ± 0.5 dB ± 0.5 dB

Preamp = Off Preamp = On 9 GHz to 20 GHz Instruments Maximum Typical Maximum Typical

100 Hz to 10 MHz 10 MHz to 4 GHz > 4 GHz to 9 GHz

> 9 GHz to 14 GHz > 14 GHz to 20 GHz

–145 dBm –142 dBm –136 dBm –138 dBm

–145 dBm –148 dBm –145 dBm –139 dBm –144 dBm

–161 dBm –159 dBm –156 dBm –156 dBm

–159 dBm –164 dBm –162 dBm –159 dBm –161 dBm

26.5 GHz to 54 GHz Instruments

100 Hz to 10 MHz 10 MHz to 4 GHz > 4 GHz to 9 GHz

> 9 GHz to 14 GHz > 14 GHz to 20 GHz > 20 GHz to 32 GHz

> 32 GHz to 43.5 GHz > 43.5 GHz to 54 GHz

–145 dBm –142 dBm –136 dBm –138 dBm –135 dBm –135 dBm –130 dBm

–145 dBm –148 dBm –145 dBm –139 dBm –142 dBm –140 dBm –140 dBm –134 dBm

–161 dBm –159 dBm –156 dBm –156 dBm –154 dBm –152 dBm –147 dBm

–159 dBm –164 dBm –162 dBm –159 dBm –159 dBm –159 dBm –154 dBm –151 dBm

MS2090A TDS PN: 11410-01000 Rev. AW 7 of 40

Spectrum Analyzer Features

Smart Measurements Field Strength Measures field strength (dBm/m2, dBW/m2, dBV/m, dBmV/m, dBµV/m, V/m, W/m2, W/cm2, A/m) with antenna gain vs. frequency plot Channel Power Measures the total power and power spectral density within a specified bandwidth

Occupied Bandwidth Measures the 99 % to 1 % power channel of a signal Adjacent Channel Power Measures the power in two upper and two lower adjacent channels Spectral Emission Mask Standards based limits for wireless emissions

Carrier-to-Interference (C/I) Measures the ratio of power (dB) in an RF carrier to the interference power in the channel Burst Power Average Measures average power between two time markers in zero span

Total Harmonic Distortion (THD) Measures THD of seven harmonics relative to fundamental frequency

Setup Parameters Frequency Center/Start/Stop Frequency, Frequency Step, Frequency Offset, Gestures

Span Span (Manual/Increment 1, 2, 5) Full Span, Last Span, Zero Span Amplitude Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit (dBm, dBW, dBV, dBmV, dBµV, dBA, V, W, A), Preamp (On/Off), Attenuation (Auto/Manual), Attenuation Level, Impedance (50 Ω, 75 Ω, other), Custom IMP Loss, Field Strength, Gestures

Bandwidth RBW/VBW (Auto/Manual), VBW Type (Linear/Logarithmic), RBW:VBW Ratio, SPAN:RBW Ratio Sweep Continuous on/of, Restart, Sweep Once, Sweep to N, Auto/Manual Time, Gated Sweep (see “Gated Sweep (Option 90)” on page 12)

Spectrogram Number of Lines 142

Trace Time/Position Cursor Up to Six Cursors (display historical trace data by trace position or time) Cursor State Active, Hold/View, Blank Color Setup Color Scale Top/Bottom Range, Reference Hue

Trace Functions Traces Up to Six Traces

Trace Type Clear/Write, Average (2 to 1000), Max Hold, Min Hold, Rolling Average, Rolling Max Hold, Rolling Min Hold Trace Math T1-T2, T2-T1 (when T5 and T6 are selected) Trace Mode Active, Hold/View, Blank

Detector Type per Trace Peak, RMS/Avg, Negative, Sample, Normal Trace Normalize On/Off (defines a 0 dB reference trace)

Trace Record Record live samples with manual tagging to internal or external storage Trace Playback Play recorded samples from internal or external storage; set playback interval

CSV Logging Record live or playback traces in CSV format for post processing

Trigger Functions Trigger Input Sources (zero span only) Free Run, GNSS/Internal, Video, External1/2

Trigger Output Enables GPS 1 PPS output Settings Timestamps (on/off), Level, Time Interval, Delay, Holdoff, Periodic, Slope (Rising/Falling), Hysteresis

Refer to “IQ Waveform Capture (Option 124/126)” on page 13 for IQ Trigger Functions

Marker Functions Markers Up to 12 Markers

Marker Measurements Amplitude, Frequency (swept spectrum display) Amplitude, Time (Zero Span)

Marker Mode Normal, Delta, Fixed Delta Marker Relative to any Normal or Fixed Marker

Marker Function None, Noise, Frequency Counter (1 Hz, 100 mHz, 10 mHz, 1 mHz resolutions), Quasi-Peak (per CISPR 16-1-1) Marker Trace Assign Marker to any Trace Peak Search Peak Search, Next Peak, Next Peak Left, Next Peak Right, Next Point Left, Next Point Right

Peak Search Setup Peak Threshold, Peak Excursion Marker Mkr → Center, Mkr → Ref Level

Marker Table Up to 12 Markers Showing Marker, Mode, Function, Trace, Frequency, Amplitude, Delta Frequency & Offset

Limit Line Functions Limit Setup Upper/Lower, Limit On/Off, Limit Alarm On/Off, Set Default Limit Line, Frequency Mode (Absolute/Relative)

Amplitude Mode (Absolute/Relative) Limit Line Edit Frequency, Relative Frequency, Amplitude, Relative Amplitude, Add Point, Add Vertical, Add Gap, Delete

Point, Next Point Left/Right Limit Line Move Center, X-Offset (Hz), Left, Right, Y-Offset, Up, Down, To Marker 1, Marker 1 Offset (dB)

Limit Line Envelope Select Envelope (Upper/Lower), Set Envelope, Envelope Points (2-41), Amplitude Offset, Shape (Square/Slope)

8 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Real-Time Spectrum Analyzer (Option 199)

Setup Parameters Frequency Center/Start/Stop, Frequency Step, Frequency Offset

Gestures (Drag Center Frequency (on/off), Pinch Span (on/off)) Span, Full Span (max span: 22 MHz standard, 55 MHz with Option 103, 120 MHz with Option 104, 150 MHz with Option 105)

Amplitude Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit (dBm, dBW, dBV, dBmV, dBµV, dBA ), Preamp, Attenuation (Auto/Manual), Gestures

Bandwidth RBW (span dependent), Auto RBW, Span:RBW Ratio

Setup Show Density (on/off), Auto Scale (on/off), Density Scale Top/Bottom (100% max), Density Res (Normal, High) Density Resolution

Density Color Set Color Top/Bottom Range, Auto Scale Persistence Infinite or Variable from 0 to 10 s

Acquisition Time 50 ms to 5 s FFT Rate 527,000 FFT/s (normal resolution), 263,000 FFT/s (high resolution)

Minimum Detectable Signal 5 ns

Trace Functions Traces Up to Six Traces

Trace Type Clear/Write, Average (2 to 1000), Max Hold, Min Hold, Rolling Average, Rolling Max Hold, Rolling Min Hold, T1-T2, T2-T1

Trace Mode Active, Hold/View, Blank Detector Type per Trace Peak, Sample, Negative, Normal

Trace Record Record live samples with manual tagging to internal or external storage (only applies to trace and not for spectral density graphic)

Trace Playback Play recorded samples from internal or external storage; set playback interval (only applies to trace and not for spectral density graphic)

CSV Logging Record live or playback traces in CSV format for post processing

Sweep Functions Sweep Single/Continuous, Sweep Once

Spectrogram Number of Lines 142

Trace Time/Position Cursor Up to Six Cursors (display historical trace data by trace position or time) Cursor State Active, Hold/View, Blank Color Setup Color Scale Top/Bottom Range, Reference Hue, Preset Setup

Marker Functions Markers Up to 12 Markers

Marker Measurements Power, Frequency, Time (Spectrogram) Marker Mode Normal, Delta, Fixed Delta Marker Relative to any Normal or Fixed Marker

Marker Function None, Noise Marker Trace Assign Marker to any Trace Peak Search Peak Search, Next Peak, Next Peak Left, Next Peak Right, Next Point Left, Next Point Right

Peak Search Setup Peak Threshold, Peak Excursion Marker → Mkr → Center, Mkr → Ref Level

Marker Table Up to 12 Markers Showing Marker Mode, Function, Trace, Frequency, Amplitude, Delta Frequency & Offset

Limit Line Functions Limit Setup Upper/Lower, Limit On/Off, Limit Alarm On/Off, Set Default Limit Line, Frequency Mode (Absolute/Relative), Amplitude Mode (Absolute/Relative) Limit Line Edit Frequency, Amplitude, Add Point, Add Vertical, Add Gap, Delete Point, Next Point Left/Right

Limit Line Move Center, X-Offset, Left, Right, Y-offset, Up, Down, Marker Offset, To Marker 1 Limit Line Envelope Select Envelope (Upper/Lower), Envelope Points (41 max), Amplitude Offset, Shape (Square/Slope), Set Envelope

Probability of Intercept Analysis Bandwidth Density Resolution Span RBW POI 22 MHz (Standard)

55 MHz (Opt. 103)

120 MHz (Opt. 104)

150 MHz (Opt. 105)

Normal High Normal High Normal High Normal High

22 MHz

55 MHz

120 MHz

150 MHz

10 MHz

25 MHz

40 MHz

40 MHz

2.520 µs

4.420 µs

2.210 µs

4.110 µs

2.055 µs

3.950 µs

2.055 µs

3.950 µs

MS2090A TDS PN: 11410-01000 Rev. AW 9 of 40

Trigger Functions Source Free Run, Video, External1/2

Settings Timestamps (on/off), Level, Time Interval, Delay, Holdoff, Periodic, Slope (Rising/Falling), Hysteresis Refer to “IQ Waveform Capture (Option 124/126)” on page 13 for IQ Trigger Functions

Secure Data Operation (Option 7) For highly secure data handling requirements, Secure Data Option 7 prevents the storing of measurement setup or data information onto any internal file storage location. Instead, setup and measurement information is stored ONLY to the external USB memory location. A simple factory preset prepares the Field Master Pro for transportation while the USB memory remains behind in the secure environment. The Field Master Pro cannot be switched between secure and non-secure operation by the user once configured for secure data operation. With this option enabled, the user can also choose to blank the frequency, amplitude and bandwidth values displayed on the screen by turning on Secure Display toggle included in Advanced settings of the instrument.

Note that the SCPI command interface won't be supported when Option 7 is installed and installing Secure Communication Option 17 is required to enable the SCPI interface.

Secure Communication (Option 17) When connecting the instrument to a network, Option 17 creates a secure tunnel. Some ports will be closed, and data gets encrypted as shown in the table below. Security certificates can be loaded onto the instrument to establish a secure connection. Remote access to the MS2090A ports can be password protected. The USBTMC connection interface does not work on instruments installed with Secure Communication Option 17.

Compatible Software Anritsu Remote and Report Tools (ARRT) MX280007A Mobile InterferenceHunter™ (MIH)

PORT SERVICE DEFAULT STATE WITH OPTION 17

21 (tcp) ftp Open Closed 80 (tcp) http Open Closed

111 (tcp) rpcbind Open Open 443 (tcp) https Open Open

8001 (tcp) vcom-tunnel Open Closed 8002 (tcp) vcom-tunnel Closed Open (encrypted) 9001 (tcp) tor-orport Open Closed 9002 (tcp) dynamid Open Closed 9003 (tcp) tor-orport Closed Open (encrypted) 9004 (tcp) dynamid Closed Open (encrypted)

24001 (tcp) med-fsp-rx Open Closed 24002 (tcp) med-fsp-rx Closed Open (encrypted) 111 (udp) rpcbind Open Open 123 (udp) ntp Open Open

5353 (udp) Zeroconf Open/Filtered Open

10 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

High Accuracy Power Meter (Option 19) (requires external USB power sensor, sold separately)

Inline Peak Power Sensor Amplitude External Gain/Loss, Forward/Reverse Relative Power (on/off), Maximum/Minimum Display, Units (dBm, W)

Sweep Measurement Mode (Single, Continuous), Run/Hold, Single Setup Averages (1-100), Max Hold (on/off), Summary Table on/off, Modulation Type (None, GSM GPRS EDGE, WCDMA HSPA Single/Multi Carrier, ISDB T, CDMA IS95 2000 EVDO), Forward Measurement (Crest Factor, Burst Average Manual, Peak Envelope Power, Burst Average Auto, CCDF), Reverse Measurement (Reverse Average, Reflection Coefficient, Return Loss, Standing Wave Ratio), Duty Cycle, Video BW, CCDF Threshold, Sensor Info

Zero/Cal Zero, Cal Frequency, Signal Standard, Limits Enabled on/off, Forward Upper/Lower, Reverse Upper/Lower, Alarm On/Off

Power Sensor Amplitude External Gain/Loss, Relative Power On/Off, Units (dBm, W), Maximum/Minimum Display

Sweep Measurement Mode (Single, Continuous), Run/Hold, Single Setup Averages (1-100), Max Hold (on/off), Aperture, Sensor Info

Zero/Cal Zero, Cal Frequency, Signal Standard, Limits Enabled on/off, Upper, Lower, Alarm On/Off

Power Sensor Model MA24103A/105A MA24106A MA24108A/18A/26A MA24208A/18A MA24330A/40A/50A Description Inline Peak Power

Sensor High Accuracy RF Power Sensor

Microwave USB Power Sensor

Microwave Universal USB Power Sensor

Microwave CW USB Power Sensor

Frequency Range 25 MHz to 1 GHz 350 MHz to 4 GHz

50 MHz to 6 GHz 10 MHz to 8/18/26 GHz

10 MHz to 8/18 GHz 10 MHz to 33/40/50 GHz

Connector Type N(f), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω (8/18 GHz) Type K(m), 50 Ω (26 GHz)

Type N(m), 50 Ω Type K(m), 50 Ω (33/40 GHz) Type V(m), 50 Ω (50 GHz)

Dynamic Range +3 dBm to +51.76 dBm (2 mW to 150 W)

–40 dBm to +23 dBm (0.1 µW to 200 mW)

–40 dBm to +20 dBm (0.1 µW to 100 mW)

–60 dBm to +20 dBm (1 nW to 100 mW)

–70 dBm to +20 dBm (0.1 nW to 100 mW)

Measurand True-RMS, Burst Average Power

True-RMS True-RMS, Slot Power, Burst Average Power

True-RMS, Slot Power, Burst Average Power

Average Power

Measurement Uncertainty ± 0.17 dBa ± 0.16 dBb ± 0.18 dBc ± 0.17 dBd ± 0.17 dBe

Data sheet (for complete specifications)

11410-00621 11410-00424 11410-00504 11410-00841 11410-00906

Notes: a. Expanded uncertainty with K=2 for power measurements of a CW signal greater than +20 dBm with a matched load. Measurement results referenced to the input side of the sensor.

b. Total RSS measurement uncertainty (0 ºC to 50 ºC) for power measurements of a CW signal greater than

– 20 dBm with zero mismatch errors.

c. Expanded uncertainty with K=2 for power measurements of a CW signal greater than –20 dBm with zero mismatch errors.

d. Power uncertainty expressed with two sigma confidence level for CW measurement after zero operation. Includes calibration factor and linearity over temperature uncertainties, but not the effects of mismatch, zero set and drift, or noise.

e. Includes linearity over temperature uncertainties, but not the effects of calibration factor, mismatch, zero set and drift, and noise.

MS2090A TDS PN: 11410-01000 Rev. AW 11 of 40

Interference Finder and AM/FM Audio Demodulation (Option 24) (Spectrum Analyzer, RTSA, requires GNSS Receiver (Option 31), directional antenna recommended, sold separately)

Supported Measurements Interference Finding Audio Tone AM/FM Audio Demodulation Interference Triangulation Mapping (Requires MA2700A) Interference Polar Plot (Requires MA2700A)

Interference Finder Audio Tone (for use with directional antennas, sold separately) Setup Integration Bandwidth, Power Limit, MAX/MIN Level, Volume

Audio Tone 20 Hz to 20 kHz (Tone pitch and volume changes with detected signal strength)

AM/FM Audio Demodulation Demod Frequency Full range of instrument

Audio Demodulation AM, USB, LSB, Wideband FM, Narrowband FM (6.25, 12.5, 25 kHz) Demod Marker On/Off

Markers Selectable demodulation marker (1 to 12) Audio Toggle On/Off

Volume Set 0% to 100% Record Audio Record audio up to 100,000 s (dependent on instrument memory) Squelch Level –120 dBm to +30 dBm (set RF level threshold to break audio silence, supports log and linear units)

Interference Map Triangulation (for use with InterferenceHunter handle and directional antenna, sold separately) Triangulation Triangulates on source of interference location using eCompass and digital maps displayed on screen Manual Setup Manual entry of compass bearing values for signals above 6 GHz

Interference Polar Plot (for use with InterferenceHunter handle and directional antenna, sold separately) Signal Strength Radar Plot 360º radar plot of single frequency signal strength centered on current GNSS location

Channel Scanner (Option 27)

Number of Channels 1 to 60 Frequency Range 9 kHz to 54 GHz

Frequency Accuracy ±3.0 x 10–7

Measurement Range –160 dBm to +30 dBm Amplitude Reference Level (Manual/Auto and Offset), Scale/Division, Preamp (On/Off), Attenuation (Auto/Manual), Y-Axis Unit (dBm, dBW, dBV, dBmV, dBµV, dBA, V, W, A), Attenuation Level, Impedance (50 Ω, 75 Ω, other), Custom IMP Loss, Field Strength

Scan Continuous (on/off), Scan Once Measure View: Bar Chart, Strip Chart, Mapping, Start Measure, Select Points (on/off), Clear Points, Compare Measure on/off Setup Parameters Bar Chart/Strip Chart: Add Channels

Signal Standard: Start Channel, Channel Step Size, Channel Span, Channel Count, Index, Dwell Time, Upper Limit, Lower Limit Frequency Range: Channel Name, Start Frequency, Channel Spacing, Channel Span, Channel Count, Index, Dwell Time, Upper Limit, Lower Limit Custom: Channel Name, Center Frequency, Channel Span, Index, Dwell Time, Upper Limit, Lower Limit Mapping: Add Channels, Map Type (Outdoor, Indorr), Map Mode (RSSI, Channel Power, Spectral Density), Repeat Type (Time, Distance), Time (1 to 60 s max), Distance, Distance Unit (Meters, Feet), Best Channel (on/off), Selected Channel (0 to 59), Mapping Device (with Option 7 only), Color Setup: Excellent, Very Good, Good, Fair, Poor

GNSS Receiver (Option 31) (requires external GNSS antenna, sold separately)

Supported Satellite Systems GNSS (includes combinations of GPS, GLONASS, Galileo, BeiDou) Setup On/Off, Antenna Voltage 3.3 V/5.0 V, GPS/GNSS Info

GNSS Time/Location Indicator UTC Time, Latitude, Longitude, and Altitude on display (UTC Time and Altitude on GPS/GNSS Info display) High Frequency Accuracy < ± 2.5 x 10–8 with GNSS On, 3 minutes after satellite lock in selected mode (GNSS antenna connected)

< ± 5.0 x 10–8 24 hour holdover accuracy, –10 °C to 55 °C ambient temperature (GNSS antenna disconnected)

Connector SMA(f), 50 Ω

12 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Zero Span IF Output (Option 89)

Mode Spectrum Analyzer/Zero Span only Center Frequency 325 MHz (nominal, FFT capture BW ≤ 32 MHz)

300 MHz (nominal, FFT capture BW > 32 MHz, requires Option 103 or 104) Output Level –4 dBm (nominal, –20 dBm input level, 0 dB input attenuation, preamp Off, 10 MHz input frequency)

Spectrum is inverted in certain input RF bands.

Reference Level –57 dBm to +30 dBm (Preamp Off)

–87 dBm to –40 dBm (Preamp On) IF Bandwidth ≤32 MHz; ≤110 MHz with Option 103 or 104

Rise Time <20 ns Connector SMA(f), 50 Ω

Gated Sweep (Option 90)

Gate Source GNSS (GPS), External 1/2 Trigger Slope Rising/Falling

Frame Time 1 s, 20 ms, 10 ms Gate Delay Up to 200 ms

Gate Length 1 µs up to 200 ms Power vs. Time, Display Length 100 µs to 200 ms

MS2090A TDS PN: 11410-01000 Rev. AW 13 of 40

IQ Waveform Capture (Option 124/126) (Option 126 is non-export controlled and limits bit depth to 8 or 10 bits when bandwidth is 150 MHz)

IQ Capture Mode Spectrum Analyzer, RTSA

Capture Mode Single, Continuous, Streaming Capture Settings Capture Length, Time Stamps (on/off), Save to File (Automatic/Normal), Save Capture, File Name Prefix

Capture Signing (on/off), Storage Device (Internal/USB) Trigger Source Free Run, External 1/2, Video

Trigger Settings Time Stamps (on/off), Level, Delay (negative in RTSA mode only), Time Interval, Slope (Rising/Falling), Hysteresis

Maximum Sample Ratea 200 MHz Maximum Signal Bandwidtha 150 MHz

Bit Resolution 8, 10, 16, or 32-bit Total Capture Memory 2 GB

IQ Capture Time Typical Maximum

IQ Waveform Streaming (Option 125/127) (requires Option 124 or 126; Option 127 is non-export controlled and limits streams to 100 MHz BW or less.)

Bit Resolution 8, 10, 16, or 32-bit Ethernet Port Maximum gapless bandwidth depends on network transfer speed

USB Port Requires USB 3.0 solid state drive.

Device formatted as external file system (ext4). Maximum gapless streaming bandwidth:

8 bit: 100 MHz BW, 122.88 MSPS sample rate 10 bit: 80 MHz BW, 100 MSPS sample rate 16 bit: 50 MHz BW, 61.44 MSPS sample rate 32 bit: 25 MHz BW, 30.72 MSPS sample rate Device formatted as extensible file allocation table system (exFAT) with 32 MB allocation unit size Maximum gapless streaming bandwidth:

8 bit: 100 MHz BW, 122.88 MSPS sample rate 10 bit: 74 MHz BW, 92.16 MSPS sample rate 16 bit: 50 MHz BW, 61.44 MSPS sample rate 32 bit: 25 MHz BW, 30.72 MSPS sample rate

Data Out Port (PCIe) Gapless streaming of 150 MHz bandwidth at 16-bit resolution or 100 MHz bandwidth at 32-bit resolution (requires MA25101A IQ Streaming PCIe kit and compatible PC)

Signal Bandwidth IQ Sample Rate IQ Bit Resolution Modea

a. Option Dependent: Standard Analysis Bandwidth up to 20 MHz, Option 103 up to 55 MHz, Option 104 up to 120 MHz and Option 105 up to 150 MHz.

(MHz) (MSPS) 32 bit 16 bit 10 bit 8 bit SPA RTSA 150 200 1.34 s 2.68 s 4.29 s 5.37 s x x 120 200 1.34 s 2.68 s 4.29 s 5.37 s x x 110 200 1.34 s 2.68 s 4.29 s 5.37 s x x 100 122.88 2.18 s 4.37 s 6.99 s 8.74 s x

80 100 2.68 s 5.37 s 8.59 s 10.74 s x x 74 92.16 2.91 s 5.83 s 9.32 s 11.65 s x 50 61.44 4.37 s 8.74 s 13.98 s 17.48 s x 40 50 5.37 s 10.74 s 17.18 s 21.47 s x x 36 46.08 5.83 s 11.65 s 18.64 s 23.3 s x 25 30.72 8.74 s 17.48 s 27.96 s 34.95 s x 20 25 10.74 s 21.47 s 34.36 s 42.95 s x x 18 23.04 11.65 s 23.30 s 37.28 s 46.6 s x 12 15.36 17.48 s 34.95 s 55.92 s 1.17 min x 10 12.5 21.47 s 42.95 s 1.15 min 1.43 min x x

6 7.68 34.95 s 1.17 min 1.86 min 2.33 min x 5 6.25 42.95 s 1.43 min 2.29 min 2.86 min x x 3 3.84 1.17 min 2.33 min 3.73 min 4.66 min x

2.5 3.125 1.43 min 2.86 min 4.58 min 5.73 min x x

1.5 1.92 2.33 min 4.66 min 7.46 min 9.32 min x

1.25 1.5625 2.86 min 5.73 min 9.16 min 11.45 min x x

0.28 0.36 12.43 min 24.86 min 39.77 min 49.71 min x

0.036 0.045 99.42 min 198.84 min 318.15 min 397.68 min x

14 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Cable and Antenna Analyzer (Option 331) (requires external Site Master™ S331P analyzer, sold separately)

Frequency Frequency Ranges 150 kHz to 4 GHz (S331P-0704)

150 kHz to 6 GHz (S331P-0706) Frequency Accuracy ± 2.5 ppm @ 23 °C ± 3 °C

Frequency Resolution 1 kHz Refer to the Site Master S331P Technical Data Sheet (11410-00964) for hardware characteristics, performance specifications, compliance information, and related accessories for the S331P analyzer.

Smart Measurements Return Loss Measures the reflected power in dB

VSWR Measures the ratio of voltage peaks to voltage valleys caused by reflections Cable Loss Measures the signal attenuation level of a cable

Distance-to-Fault (DTF) Return Loss/VSWR Measures distance of the cable to facilitate precise fault location of components in a transmission line 1-Port Phase Displays the phase of the reflection measurements at the RF port Smith Chart Converts the measured reflection coefficient data into complex impedance data

Transmission (USB Sensor) Measures the loss (or gain) in dB of a device TDR Ohm/Linear (Option 3) Measures the impedance against distance

Setup Parameters Frequency/Distance Start Frequency, Stop Frequency

Distance and DTF Setup Start Distance, Stop Distance, Units m/ft, Start Frequency, Stop Frequency, Data Points, Cable List, Cable Loss, Propagation Velocity

Windowing Rectangular, Normal Side Lobe, Low Side Lobe, Minimum Side Lobe Amplitude Top, Bottom, Auto Scale, Full Scale

Measure Count (1/2), Select (Trace 1/Trace 2), Display Layout (Single, Horizontal Split) with independent markers Data Points Flex Cal: 2 to 10,049, user defined

Standard Cal: Snaps to nearest calibration point OSL Calibration: 10,049, 5025, 2513, 1257, 629, 315, 158, 65, 33, 17, 9, 5, 3 and 2 OSL + Trans (USB Sen)/Trans (USB Sen) Calibration: 1251, 626, 251, 126, 51, 26, 11, 6, 3 and 2

Sweep Data Points, Run/Hold, Sweep Type (Single/Continuous), Sweep Rate (Normal/Fast), Sweep Once Averaging State (on/off), Sweep Averaging, Restart Averaging, RF Immunity (High/Low), RF In Hold (on/off)

Marker Markers 1 to 8 (On/Off), Delta Markers 2 to 8 (Ref M1), Track Marker (On/Off), Marker Search (Peak/Valley), Marker Table (on/off), To Memory (On/Off), Mode (Reference), Independent Markers for Frequency and Distance Measurements

Limit Upper Limit (on/off), Lower Limit (on/off), Upper/Lower Level Limit Test (On/Off), Move Active Limit, Edit Segments (42 upper and 42 lower segments maximum), Limit Alarm, Pass/Fail On/Off, Limit Preset

Calibration Start/Cancel Calibration, Cal Setup, Cal Info, User Cal (On/Off), USB CAA Info, Power Sensor Method: OSL, OSL + Trans (USB Sen), Trans (USB sen), iOSL (only with ICN51A connected), iOSL + Trans (USB Sen) Type1: Standard, FlexCal™

Trace Copy To Memory, Memory Display (Trace, Memory, Both) Math: None, Trace - Memory, Trace + Memory, (Trace + Memory)/2, Smoothing (0 to 20%)

File Quick Save, Save As, Recall, Browse Files, PDF Report: Report Setup, Template, Report Name, Generate Report, Preview Last Report

Time Domain Reflectometry (TDR) Measurement (Option 3) (Requires Option 331 and S331P, sold separately) The TDR option complements the Distance-to-Fault (DTF) measurement by providing additional information about reflections in a transmission line. The resistive, capacitive and inductive component of individual reflections can be identified which provides an additional insight about the nature of the reflection. This information can be used in the identification and repair of faults in a transmission line. The TDR measurement is implemented using lowpass step response.

Measurements Display Layout Single screen or split screen display including TDR/DTF, TDR/Return Loss

Distance 5000 Meters Distance Units Meters, Feet

TDR Ohm Measurement Range 0 Ω to 5000 Ω Resolution 0.01 Ω

TDR Linear Measurement Range 0 U to 500 U Resolution 0.01 U

1. Factory default 1-Port ReadyCal (automatically applied to all measurements), User calibration (User Cal) overrides ReadyCal.

MS2090A TDS PN: 11410-01000 Rev. AW 15 of 40

Pulse Analyzer (Option 421)

Pulse Measurements (in accordance with IEEE Standard for Transitions, Pulses, and Related Waveforms (181-2011, section 5.2.1) Power Measurements Average power, Peak power, Wave Average, Peak Wave Average, Pulse Average

Pulse Characteristics Duration, Center, Tilt, Period, Off Time, Duty Factor, Frequency First Transition Characteristics Transition Duration, Duration Instant, Low Reference Instant, High Reference Instant, Pre Transition Overshoot, Post Transition Overshoot, Pre Transition Undershoot, Post Transition Undershoot

Second Transition Characteristics Transition Duration, Duration Instant, Low Reference Instant, High Reference Instant Pulse View Settings Pulse Analyzer (enables pulse analyzer measurements above), Pulse Viewer (removes pulse analyzer measurements and enables standard marker measurements) Rise Time (trace averages set to 100; RBW:VBW = 1)

30 ns, 40 MHz RBW (Option 104) 60 ns, 25 MHz RBW (Option 103) 100 ns, 10 MHz RBW (Standard)

DANL and dynamic range are the same as the “Spectrum Analyzer Performance”.

Setup Parameters Frequency Center Frequency, Frequency Step, Frequency Offset Amplitude Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit (dBm, dBW, dBV, dBmV, dBµV, dBA), Preamp On/Off, Attenuation (Auto/Manual) Bandwidth RBW/VBW (Auto/Manual), VBW Type (Linear/Logarithmic), RBW:VBW Ratio, SPAN:RBW Ratio

Pulse Setup Pulse Level Type (Auto/User), Pulse Type (Positive/Negative), User TOP (S2), User BOTTOM (S1), Pulse Reference High (%), Pulse Reference Low (%), Pulse Duration Reference (0.2-99.9%), Simulation, Display

Trace Functions Traces Up to Six Traces

Trace Type Clear/Write, Min Hold, Max Hold, Average, Rolling Max Hold, Rolling Min Hold, Rolling Average Trace Mode Active, Hold/View, Blank

Detector Type per Trace Peak, Negative, Sample

Sweep Functions Sweep Single/Continuous, Restart, Sweep Once, Sweep to N, Sweep Time

Sweep Points 1001 Sweep Time 60 ns to 3600 s

Sweep Time Accuracy ±2%

Marker Functions (enabled only in Pulse Viewer) Markers Up to 12 Markers

Marker Measurements Time, Amplitude Marker Mode Normal, Delta, Fixed Delta Marker Relative to any Normal or Fixed Marker

Marker Function None, Noise Marker Trace Assign Marker to any Trace Peak Search Peak Search, Next Peak, Next Peak Left, Next Peak Right, Next Point Left, Next Point Right

Peak Search Setup Peak Threshold, Peak Excursion Marker → Mkr → Center, Mkr → Ref Level

Marker Table Up to 12 Markers Showing Marker Mode, Function, Trace, Time, Amplitude, Delta Time & Offset

Trigger Functions Trigger Sources Free Run, Video, External 1/2 Trigger Settings Level, Delay, Holdoff, Periodic, Slope (Rising/Falling), Hysteresis

Trigger Jitter 20 ns

Pulse Simulation Provides visual and measurement data of simulated pulse types.

Waveform Types Single Positive, Single Negative, Train, Double

Settings Simulation (ON/OFF) Amplitude (High and Low), Period (0 s-3600 s), Duty Factor (0.01-1)

Pulse Display Settings Ref High (On/Off), Duration Ref (On/Off), Post-T Over (On/Off), Post-T Under (On/Off), Pre-T Over (On/Off), Pre-T Under (On/Off), S2 High (On/Off), S1 Low (On/Off), HRI First/Second, LRI First/Second, DI First/Second (On/Off)

16 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

Coverage Mapping (Option 431) (Spectrum Analyzer, 5GNR, LTE measurements)

Spectrum Analyzer Measurements Channel Power Plots channel power in dBm, dBW, dBV, dBmV, dBµV, dBA, V, W, A

Spectral Density Plots spectral density in dBm/Hz, dBW/Hz, dBV/Hz, dBmV/Hz, dBµV/Hz, dBA/Hz, V/Hz, W/Hz, A/Hz RSSI Plots received signal strength indicator in dBm, dBW, dBV, dBmV, dBµV, dBA, V, W, A

Field Strength Plots field strength in dBm/m2, dBW/m2, dBV/m, dBmV/m, dBµV/m, dBA/m, V/m, W/m2, W/cm2, A/m2 Power Flux Density Plots power flux density in dBm/m2/Hz, dBW/m2/Hz, dBV/m/Hz, dBmV/m/Hz, dBµV/m/Hz, dBA/m/Hz, V/m/Hz, W/m2/Hz, W/cm2/Hz, A/m/Hz

Spectrum Analyzer Measurement Setup Map Type Indoor: PNG or JPEG

Outdoor: OpenStreetMap® (downloaded direct from Internet to instrument or using external PC software) Frequency (Excluding RSSI) Center/Start/Stop, Frequency Step, Frequency Offset

Span (Excluding RSSI) Span (Manual/Increment 1, 2, 5), Full Span, Last Span, Zero Span Amplitude Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit, Preamp (on/off), Attenuation

(Auto/Manual), Field Strength, Impedance (50 Ω, 75 Ω, other), Custom IMP Loss Bandwidth RBW/VBW (Auto/Manual), VBW Type (Linear/Logarithmic), RBW:VBW Ratio, SPAN:RBW Ratio

Mapping Colors Customizable Amplitude Range Thresholds for Each Color Blue (Excellent), Green (Very Good), Yellow (Good), Orange (Fair), Pink (Poor)

Point Distance or Time Setup Repeat Type: Time (1 s to 60 s) or Distance (1 m to 10,000 m), Distance Units: Meters or Feet Save Indoor: Setup, Measurement File (fmspa), PNG

Outdoor: Setup, KML Points, PNG, Tab Delimited Recall Setup, KML Points File, Measurement File (fmspa)

LTE Measurements (Option 883 is required (see “LTE FDD/TDD Signal Analyzer (Option 883)” on page 20)) Channel Power Plots channel power in dBm, dBW, dBV, dBmV, dBµV, dBA

Spectral Density Plots spectral density in dBm/Hz, dBW/Hz, dBV/Hz, dBmV/Hz, dBµV/Hz, dBA/Hz RSRP Plots received signal strength indicator in dBm, dBW, dBV, dBmV, dBµV, dBA RSRQ Plots received signal strength indicator in dB SINR Plots received signal strength indicator in dB

LTE Measurement Setup Map Type Indoor: PNG or JPEG

Outdoor: OpenStreetMap® (downloaded direct from Internet to instrument or using external PC software) Frequency Center Frequency, Channel Bandwidth, EARFCN, Signal Standard Amplitude Auto Range (On/Off), Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit, Preamp (on/off), Attenuation (Auto/Manual) Bandwidth RBW/VBW (Auto/Manual), VBW Type (Linear/Logarithmic), RBW:VBW Ratio, SPAN:RBW Ratio

Mapping Colors Customizable Amplitude Range Thresholds for Each Color Channel Power and Spectral Density: Blue (Excellent), Green (Very Good), Yellow (Good), Orange (Fair), Pink (Poor) RSRP, RSRQ, SINR: Blue (Excellent), Green (Good), Yellow (Poor), Pink (Bad), Gray (No Sync)

Point Distance or Time Setup Repeat Type: Time (1 s to 60 s) or Distance (1 m to 10,000 m), Distance Units: Meters or Feet Map Source Any PCI, Defined PCI, Available PCI Filter, Manual PCI Filter

Save Indoor: Setup, Measurement File (fmlte), PNG Outdoor: Setup, KML Points, CSV, PNG, Recall Setup, KML Points File

5GNR Measurement (Option 888 is required (see “5GNR FDD/TDD Signal Analyzer (Option 888)” on page 22)) Channel Power Plots channel power in dBm, dBW, dBV, dBmV, dBµV, dBA

Spectral Density Plots spectral density in dBm/Hz, dBW/Hz, dBV/Hz, dBmV/Hz, dBµV/Hz, dBA/Hz SS-RSRP Plots received signal strength indicator in dBm, dBW, dBV, dBmV, dBµV, dBA SS-RSRQ Plots received signal strength indicator in dB SS-SINR Plots received signal strength indicator in dB

MS2090A TDS PN: 11410-01000 Rev. AW 17 of 40

5GNR Measurement Setup Map Type Indoor: PNG or JPEG

Outdoor: OpenStreetMap® (downloaded direct from Internet to instrument or using external PC software) Frequency Center Frequency, Channel Bandwidth, SSB Frequency, SSB Offset, Auto Detect SSB, Subcarrier Spacing, Mapping Pattern (P1, P2, Auto), Band Config: Band (Manual, Global All), ARFCN, Channel BW, GSCN Amplitude Auto Range (On/Off), Reference Level (Manual/Auto and Offset), Scale/Division, Y-Axis Unit, Preamp (on/off), Attenuation (Auto/Manual) Bandwidth RBW/VBW (Auto/Manual), VBW Type (Linear/Logarithmic), RBW:VBW Ratio, SPAN:RBW Ratio

Mapping Colors Customizable Amplitude Range Thresholds for Each Color Channel Power and Spectral Density: Blue (Excellent), Green (Very Good), Yellow (Good), Orange (Fair), Pink (Poor) SS-RSRP, SS-RSRQ, SS-SINR: Blue (Excellent), Green (Good), Yellow (Poor), Pink (Bad), Gray (No Sync)

Point Distance or Time Setup Repeat Type: Time (1 s to 60 s) or Distance (1 m to 10,000 m), Distance Units: Meters or Feet Map Source Any PCI, Defined PCI, Available PCI Filter, Manual PCI Filter

Save Indoor: Setup, Measurement File (fm5gnr), PNG Outdoor: Setup, KML Points, PNG, CSV

Recall Setup, KML Points File

Electromagnetic Field (EMF) Measurement (Option 444) (requires a supported antenna, sold separately) The Spectrum Analyzer mode provides electromagnetic field strength measurements in three axis (X, Y, Z) with trace displays for each measurement and tabular results.

Measurements/Settings Setup Limit lines, Axis Dwell Time, Measurement Time, Measurement Count, Measurement Units, Data Logging with storage location Units dBm/m2, dBW/m2, dBV/m, dBmV/m, dBµV/m, V/m, W/m2, W/cm2, A/m

Results Maximum, Minimum, and Average of all measurements conducted Displayed Information Measurement progress, number of measurements taken, Pass/fail indicators

Frequency Range Supported Antenna

2000-1800-R 9 kHz to 300 MHz

Electromagnetic Field (EMF) Meter (Option 445) (requires a supported probe, sold separately) The EMF Meter mode provides electromagnetic field strength measurements in three axis (X, Y, Z) with bar graph for each measurement and tabular results.

Measurements/Settings Limit Standard (FCC Public, ICNIRP Public, FCC Workers, ICNIRP Worker), Limit Mode (Lowest, Frequency), Alarm, Volume, Mute, Preset Supports the International Commission on Non-Ionizing Radiation Protection limit (ICNIRP)

Measure Selected sample (1 through 16), Start Sampling, Clear Results Setup EMF Meter Calibration, Probe info Units mW/cm2

Preset Preset Mode Setup File Quick save, Save As, Recall (.stp file type), Browse Files

Results (%) Maximum, Minimum, and Average of all samples (1 through 8) Display Bar graph of each sample (1 through 16) with Standard Limit Line, Time (mm:ss)

Frequency Range Supported Probe

2000-1985-R Isotropic EMF Probe, 20 MHz to 40 GHz (refer to data sheet 11410-01185)

18 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

AM/FM Modulation Measurement (Option 509) (Spectrum Analyzer, RTSA, IA Spectrum and IA RTSA measurements)

AM Measurements AM Depth 0% to 100%, ±2% accuracy, typical

AM Bandwidth 20 kHz AM Standards Standard AM, Upper/Lower Sideband suppressed carrier

SINAD 0 to 60 dB, nominal based on 1kHz modulating tone THD -60 dB, using up to 10 harmonics of 1 kHz modulating tone

Demodulated AM Spectrum Frequency Scale, 0 to 24 kHz Audio Time Domain 5 s or auto zoomed

Graphs Audio Spectrum (Log AM depth percentage vs frequency), RF Spectrum Audio Time Domain (Linear AM depth percentage vs time), Audio Results

Audio Results Signal Power (dBm), Carrier Frequency, RMS Depth, (Peak-to-peak)/2 Depth, Peak Positive/Peak Negative Depth, SINAD (dB), Upper/Lower AM Depth, THD (dB)

Setup Demodulation Frequency, Demodulation Marker (on/off), Marker Tracked (1 to 12), Zoomed Time Graph (on/off), Modulation (AM, USB, LSB), Audio (on/off), Volume (on/off), Record Duration (1 to 100000 S), Record, Squelch Level (-120 to 30 dBm)

FM Measurements FM Bandwidth 96 kHz (wide)

FM Deviation Up to 75 kHz with 2% accuracy, ±1 kHz typical SINAD 0 to 60 dB, nominal based on 1 kHz modulating tone

THD -75 to 0 dB, using up to 10 harmonics of 1 kHz modulating tone Demodulated FM Spectrum Wideband: 96 kHz full span, 20 kHz zoomed

Narrowband: 25 kHz, 24 kHz (audio spectrum)

12.5 kHz, 14 kHz (audio spectrum)

6.25 kHz, 6 kHz (audio spectrum)

Audio Time Domain 5 s or auto zoomed Graphs Audio Spectrum (Log FM deviation vs frequency), RF Spectrum

Audio Time Domain (Linear FM deviation vs time), Audio Results Audio Results Signal Power (Hz), Carrier Frequency, Upper/Lower Deviation, RMS FM deviation, (Peak-to-peak)/2 Deviation, SINAD, Total Harmonic Distortion (THD), Left/Right RDS deviation, Pilot Deviation Setup Demodulation Frequency, Demodulation Marker (on/off), Marker Tracked (1 to 12), Zoomed Audio Graph

(on/off), Zoomed Time Graph (on/off), Modulation (FM Narrowband (6.25, 12.5, 25 kHz), FM Wideband), Audio (on/off), Volume (on/off), Record Duration (1 to 100000 S), Record, Squelch Level (-120 to 30 dBm)

MS2090A TDS PN: 11410-01000 Rev. AW 19 of 40

WCDMA FDD Signal Analyzer (Option 871) (Requires Option 31)

General Frequency Range 10 MHz to 54 GHz (option dependent)

Channel Bandwidth 5 MHz Amplitude Auto Range on/off, Reference Level (Manual/Auto), Scale/Division, Y Axis Unit, Attenuation Level

(Auto/Manual), Reference Level Offset, Preamp on/off Input Signal Range –80 dBm to +10 dBm

Sweep Sweep Once/Continuous, Hold (On/Off), Restart Averaging, Gated Sweep (Channel Power and OBW)

WCDMA

Demod Summary View Sync: Primary Scrambling Code, Code Group, Frequency Error, Time Offset, Status

Frequency Error: Count, Average, STD Deviation, Minimum, Maximum Code Domain Power: Absolute, relative and ⌂ CPICH values of Channel Power (CHP), power of common pilot channel (P-CPICH), Primary Common Control Physical Channel (P-CCPCH), Secondary Common Control Physical Channel (S-CCPCH), Paging Indicator Channel (PICH) Code Domain EVM: power of common pilot channel (P-CPICH)

Summary Table View Carrier Frequency, Frequency error/Average frequency error, Channel Power, Occupied BW, P-CPICH EVM, P-CPICH Power, P-CCPCH Power, S-CCPCH Power, PICH Power, Scrambling Code

WCDMA Adjacent Channel Power Upper/Lower Measurements Channel (Main, Adjacent, Alternate) Absolute, Relative, Limit (dBm)

Setup Parameters Channel Spacing, Main/Adjacent/Alternate Integration Bandwidth, Limit Type (Absolute/Relative), Limits (On/Off), Main/Adjacent/Alternate Channel Limit

WCDMA Channel Power Measurements Total Channel Power, Total Power Spectral Density (PSD), Limit Test (CH Power and PSD)

Setup Parameters Integration Bandwidth, PSD Units (Hz/MHz), Power Limit (dBm), PSD Limit (dBm/Hz)

WCDMA Spectral Emission Mask (SEM) Measurements Segment, RBW, Peak Power, Peak Frequency, Mask Name, Reference Channel Power and Channel BW

Setup Parameters Select Mask, Import Mask, Export Mask, Reference Channel Bandwidth, Auto Max Power (on/off), Manual Max Power

WCDMA Occupied Bandwidth Measurements Occupied BW, Total Power, Value, Limit, OBW Center Frequency, Left Edge and Right Edge

Setup Parameters % OBW Power, X DB (dB), OBW Limit (on/off), Method (percent/X dB)

20 of 40 PN: 11410-01000 Rev. AW MS2090A TDS

LTE FDD/TDD Signal Analyzer (Option 883)

General Frequency Range 10 MHz to 54 GHz (option dependent)

Channel Bandwidth (MHz) 1.4, 3, 5, 10, 15, 20 Amplitude Auto Range, Reference Level (Manual/Auto), Scale/Division, Y Axis Unit, Attenuation Level (Auto/Manual), Reference Level Offset, PreAmp Input Signal Range –76 dBm to +10 dBm (≤ 20 GHz)

–72 dBm to +10 dBm (> 20 GHz) Sweep Single/Continuous, Hold (On/Off)

MIMO Antenna Setup Auto, Antenna 0, 1, 2, or 3

LTE Demodulation Summary PCI Summary Measurements Physical Cell ID, Sector ID, Cell Group, Frequency Error, Time Offset, Cyclic Prefix, Status of Primary

Synchronization Signal (PSS), MIMO Time Alignment Error, Resource Block Power, Mobile Network Code (MNC), Mobile Country Code (MCC)

Signal Power Measurements (dBm) Physical Broadcast Channel Power (PBCH), Sync Signal (SS), Reference Signal (RS), OFDM Symbol Transmit Power (OSTP)

Error Vector Magnitude Measurements (%) Physical Broadcast Channel (QPSK), Physical Downlink Shared Channel (QPSK), PDSCH (16-QAM/64-QAM/256-QAM)

Demod Summary View PCI Cell ID, Sector ID, MNC, MCC, Cell Group, Frequency Error, Time Offset, Cyclic Prefix, Sync Status, Power (PBCH, SS, RS), EVM (PBCH(QPSK), PDSCH (QPSK, 16-QAM, 64-QAM, 256-QAM), Average EVM, Peak EVM

Time Alignment Error (TAE) View PCI, Sector ID, Cell Group, Frequency Error, Time Offset, Cyclic Prefix, Sync Status, TAE between each antenna pair, Power (RS, SS), EVM (RMS, PEAK)

Resource Block Power View PCI, Sector ID, Cell Group, Frequency Error, Time Offset, Cyclic Prefix, Sync Status, RB (number of active RBs, Utilization, OSTP), EVM (QPSK, 16-QAM, 64-QAM, 256-QAM)

Summary Table View Carrier Frequency, Frequency error, Average Frequency Error, Channel Power, RS Power, Occupied BW, Physical Cell ID

Setup Parameters Integration Bandwidth (Summary Table view only), Antenna (Auto/1/2/3/4), Cyclic Prefix (Auto/Normal/Extended), Duplex Type (FDD/TDD), UL/DL Config (TDD only), CFI (Auto/CFI1/CFI2/CFI3), DSS Detect (on/off), SSB Offset, Frequency Error Type (Summary Table view only): Current, Average, Auto Detect SSB

RS Power Accuracy ± 1.0 dB typical (RF input –50 dBm to +10 dBm) Frequency Error ± 10 Hz + time base error (99 % confidence level)

Residual EVM (rms) 2.0 % typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm)

LTE DSS Detection Setup Parameters DSS Detect (On/Off), Status, PCI, Beam, SS-RSRP

LTE Multi PCI…