0923-06-068.pdf

PDF 3 MB Posted

Attached to
Preventive Maintenance
Solicitation number
0923-06-068
Issued by
Burleson County, Texas

About this file

This is a proposal document for a Texas Department of Transportation (TxDOT) construction contract awarded by the Texas Transportation Commission for preventive maintenance work in Brown County, Texas. The project consists of approximately 2.0 miles of work within Lake Brownwood State Park and McGillivray-Muse Wildlife Management Area (WMA), with completion required within 59 working days. The project includes multiple bid items spanning site preparation, excavation, embankment, pavement repair, concrete work, traffic control, erosion control, and pavement marking. Bidders must acknowledge receipt of all addenda (numbered 1-5) prior to bid opening, submit a proposal guaranty of $35,000.00 in the form of a cashier's check, teller's check, or bid bond, and comply with prevailing wage requirements applicable to the designated wage rate zone (Zone TX298 for Brown County). The contract requires coordination with Texas Parks and Wildlife Department and prohibits work on specified dates during peak park seasons.

The contract is subject to prevailing wage rates effective May 18, 2026, with workers in various classifications (such as asphalt distributors, concrete finishers, equipment operators, and laborers) compensated at zone-specific minimum rates. No Small Business Enterprise (SBE) goal is established for this project. Bidders must submit an audited financial statement and experience questionnaire at least ten days prior to the letting date, provide proof of E-Verify registration, and comply with multiple state and federal certifications including nondiscrimination, conflict of interest, Israel and energy company boycott prohibitions, and firearm entity non-discrimination provisions. The contract includes standard TxDOT specifications and special provisions governing labor practices, environmental controls, traffic management, and quality standards, with liquidated damages assessed at $911 per working day for contract delays. Contractors must maintain monthly SBE reporting if applicable and comply with all wage, safety, and performance monitoring requirements throughout the contract term.

View the file

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

Control 0923-06-068, ETC Project C 923-6-68, ETC Highway PW County BROWN

ADDENDUM ACKNOWLEDGMENT

Each bidder is required to acknowledge receipt of an addendum issued for a specific project. This page is provided for the purpose of acknowledging an addendum.

FAILURE TO ACKNOWLEDGE RECEIPT OF AN ADDENDUM WILL RESULT IN THE BID NOT

BEING READ.

In order to properly acknowledge an addendum, place a mark in the box next to the respective addendum.

ADDENDUM NO. 1

ADDENDUM NO. 2

ADDENDUM NO. 3

ADDENDUM NO. 4

ADDENDUM NO. 5

In addition, the bidder by affixing their signature to the signature page of the proposal is acknowledging that they have taken the addendum(s) into consideration when preparing their bid and that the information contained in the addendum will be included in the contract, if awarded by the Commission or other designees.

1-1

This page intentionally left blank.

Highway PW County BROWN

PROPOSAL TO THE TEXAS

TRANSPORTATION COMMISSION

2024 SPECIFICATIONS

Work Consisting of Preventive Maintenance

BROWN COUNTY, TEXAS

The quantities in the proposal are approximate. The quantities of work and materials may be increased or decreased as considered necessary to complete the work as planned and contemplated.

This project is to be completed in 59 working days and will be accepted when fully completed and finished to the satisfaction of the Executive Director or designee.

Provide a proposal guaranty in the form of a Cashier’s Check, Teller’s Check (including an Official Check) or Bank Money Order on a State or National Bank or Savings and Loan Association, or State or Federally chartered Credit Union made payable to the Texas Transportation Commission in the following amount:

THIRTY FIVE THOUSAND AND 00/100 (Dollars) ( $35,000.00)

A bid bond may be used as the required proposal guaranty. The bond form may be detached from the proposal for completion. The proposal may not be disassembled to remove the bond form. The bond must be in accordance with Item 2 of the specifications.

Any addenda issued amending this proposal and/or the plans that have been acknowledged by the bidder, become part of this proposal.

By signing the proposal the bidder certifies:

1. the only persons or parties interested in this proposal are those named and the bidder has not directly or indirectly participated in collusion, entered into an agreement or otherwise taken any action in restraint of free competitive bidding in connection with the above captioned project.

2. in the event of the award of a contract, the organization represented will secure bonds for the full amount of the contract.

3. the signatory represents and warrants that they are an authorized signatory for the organization for which the bid is submitted and they have full and complete authority to submit this bid on behalf of their firm.

4. that the certifications and representations contained in the proposal are true and accurate and the bidder intends the proposal to be taken as a genuine government record.

• Signed: **

(1) (2) (3) Print Name:

(1) (2) (3) Title:

(1) (2) (3) Company:

(1) (2) (3)

• Signatures to comply with Item 2 of the specifications.

**Note: Complete (1) for single venture, through (2) for joint venture and through (3) for triple venture.

* When the working days field contains an asterisk (*) refer to the Special Provisions and General Notes.

NOTICE TO CONTRACTORS

ANY CONTRACTORS INTENDING TO BID ON ANY WORK TO BE AWARDED

BY THIS DEPARTMENT MUST SUBMIT A SATISFACTORY “AUDITED FINANCIAL

STATEMENT” AND “EXPERIENCE QUESTIONNAIRE” AT LEAST TEN DAYS

PRIOR TO THE LETTING DATE.

UNIT PRICES MUST BE SUBMITTED IN ACCORDANCE WITH ITEM 2 OF

THE STANDARD SPECIFICATIONS OR SPECIAL PROVISION TO ITEM 2 FOR

EACH ITEM LISTED IN THIS PROPOSAL.

TEXAS DEPARTMENT OF TRANSPORTATION

BID BOND

KNOW ALL PERSONS BY THESE PRESENTS,

That we, (Contractor Name)

Hereinafter called the Principal, and (Surety Name) a corporation or firm duly authorized to transact surety business in the State of Texas, hereinafter called the Surety, are held and firmly bound unto the Texas Department of Transportation, hereinafter called the Obligee, in the sum of not less than two percent (2%) of the department’s engineer’s estimate, rounded to the nearest one thousand dollars, not to exceed one hundred thousand dollars ($100,000) as a proposal guaranty (amount displayed on the cover of the proposal), the payment of which sum will and truly be made, the said Principal and the said Surety, bind ourselves, our heirs, executors, administrators, successors and assigns, jointly and severally, firmly by these presents.

WHEREAS, the principal has submitted a bid for the following project identified as:

Control 0923-06-068, ETC

Project C 923-6-68, ETC

Highway PW

County BROWN

NOW, THEREFORE, if the Obligee shall award the Contract to the Principal and the Principal shall enter into the Contract in writing with the Obligee in accordance with the terms of such bid, then this bond shall be null and void. If in the event of failure of the Principal to execute such Contract in accordance with the terms of such bid, this bond shall become the property of the Obligee, without recourse of the Principal and/or Surety, not as a penalty but as liquidated damages.

Signed this Day of 20

By:

(Contractor/Principal Name)

(Signature and Title of Authorized Signatory for Contractor/Principal)

*By:

(Surety Name)

(Signature of Attorney-in-Fact) Impressed

*Attach Power of attorney (Surety) for Attorney-in-Fact Surety Seal Only

This form may be removed from the proposal

BIDDER’S CHECK RETURN

IMPORTANT

The space provided for the return address must be completed to facilitate the return of your bidder’s check. Care must be taken to provide a legible, accurate, and complete return address, including zip code. A copy of this sheet should be used for each different return address.

NOTE

Successful bidders will receive their guaranty checks with the executed contract.

RETURN BIDDERS CHECK TO (PLEASE PRINT):

Control 0923-06-068, ETC Project C 923-6-68, ETC Highway PW County BROWN

IMPORTANT

PLEASE RETURN THIS SHEET IN ITS ENTIRETY

Please acknowledge receipt of this check(s) at your earliest convenience by signing below in longhand, in ink, and returning this acknowledgement in the enclosed self-addressed envelope.

Check Received By: Date:

Title:

For (Contractor's Name):

Project: County:

NOTICE TO THE BIDDER

In the space provided below, please enter your total bid amount for this project. Only this figure will be read publicly by the Department at the public bid opening.

It is understood and agreed by the bidder in signing this proposal that the total bid amount entered below is not binding on either the bidder or the Department. It is further agreed that the official total bid amount for this proposal will be determined by multiplying the unit bid prices for each pay item by the respective estimated quantities shown in this proposal and then totaling all of the extended amounts.

Total Bid Amount

Control Project Highway County

ALT ITEM DESC SP Bid Item Description Unit Quantity Bid Price Amount Seq

Signed ____________________________________________ Title ____________________________________________ Date ____________________________________________

Additional Signature for Joint Venture:

Signed ____________________________________________ Title ____________________________________________ Date ____________________________________________

Total Bid Amount _______$2,664.00________

EXAMPLE OF BID PRICES SUBMITTED BY COMPUTER PRINTOUT

0001-03-030

STP 2000(938)HES

SH 20

EL PASO

104 509 REMOV CONC (SDWLK) SY 266.400 $10.000 $2,664.00 1

EXAMPLE EXAMPLE EXAMPLE EXAMPLE

EXAMPLES

BID PRICES SUBMITTED BY HAND WRITTEN FORMAT

Unit price for each plant in place

249 014 FLEX BASE(DEL)(DENSCOT)(TY A GR4 CL2) TON 56,787.00 14

ALT

ITEM-CODE

ITEM

NO

DESC

NO

S.P.

NO.

UNIT BID PRICE ONLY

WRITTEN IN WORDS UNIT

APPROX

QUANTITIES

DEPT

USE

ONLY

190 026 RED OAK 1 1/2” - 1 3/4” GAL BB EA 9.000 1

DLRS

CENTS

DLRS

CENTS

Unit price for each ton of Flexible Base

430 001 001 CL A CONC FOR EXT STR (CULV) CY 45.000 27

Unit price for each cubic yard of Concrete

DLRS

CENTS

610 007 001 RDWY ILL ASSEM(TY ST 50T-8-8)(.4 KW)S EA 13.000 7

Unit price of each Roadway Illumination Assembly

DLRS

CENTS

EXAMPLE EXAMPLE EXAMPLE EXAMPLE

C 923-6-68, ETC

Proposal Sheet

BROWN FORM 234-B I-61-5M

TxDOT PROJECT

COUNTY

ALT

ITEM-CODE

UNIT BID PRICE ONLY.

WRITTEN IN WORDS UNIT APPROX

QUANTITIES

DEPT

USE

ONLY

ITEM

NO.

DESC

CODE

S.P.

No.

100 7013

TREE PROTECTION (INSTALL)

EA 2.000 1 DOLLARS

and CENTS

100 7015

TREE PROTECTION (REMOVE)

EA 2.000 2 DOLLARS

and CENTS

104 7016

REMOV CONC (CURB)

LF 35.000 3 DOLLARS

and CENTS

110 7002

EXCAV (CHANNEL)

CY 60.000 4 DOLLARS

and CENTS

110 7003

EXCAV (SPECIAL)

CY 10.500 5 DOLLARS

and CENTS

132 7005

EMBANK (FNL)(OC)(TY C)

CY 187.600 6 DOLLARS

and CENTS

194 7007

RDSIDE AMENITY (WHEEL STOP)

EA 42.000 7 DOLLARS

and CENTS

194 7008

RDSIDE AMENITY (WHEEL STOP

REMOV&RESET)

EA 48.000 8 DOLLARS

and CENTS

216 7001

PROOF ROLLING

HR 8.000 9 DOLLARS

and CENTS

310 7004

PRIME COAT (MC-30)

GAL 2,147.000 10 DOLLARS

and CENTS

316 7007

ASPH (AC-20-5TR)

GAL 37,094.000 11 DOLLARS

and CENTS

316 7291

AGGR (TY-B, GR-4)(SAC-B)(MOD)

CY 992.000 12 DOLLARS

and CENTS

344 7065

SP MIXES SP-D SAC-B PG76-22

TON 2,751.000 13 DOLLARS

and CENTS

1-3

BROWN FORM 234-B I-61-5M

TxDOT PROJECT

COUNTY

ALT

ITEM-CODE

UNIT BID PRICE ONLY.

WRITTEN IN WORDS UNIT APPROX

QUANTITIES

DEPT

USE

ONLY

ITEM

NO.

DESC

CODE

S.P.

No.

351 7005

FLEXIBLE PAVEMENT STRUCTURE REPAIR

(6")

SY 7,156.000 14 DOLLARS

and CENTS

401 7001

FLOWABLE BACKFILL

CY 10.500 15 DOLLARS

and CENTS

420 7067

CL C CONC (MISC)

CY 161.600 16 DOLLARS

and CENTS

420 7148

CLASS K CONCRETE (MISC)

CY 2.700 17 DOLLARS

and CENTS

500 7001

MOBILIZATION

LS 1.000 18 DOLLARS

and CENTS

502 7001

BARRICADES, SIGNS AND TRAFFIC

HANDLING

MO 4.000 19 DOLLARS

and CENTS

503 7001

PORTABLE CHANGEABLE MESSAGE SIGN

DAY 4.000 20 DOLLARS

and CENTS

505 7001

TMA (STATIONARY)

DAY 2.000 21 DOLLARS

and CENTS

505 7003

TMA (MOBILE OPERATION)

DAY 2.000 22 DOLLARS

and CENTS

506 7039

TEMP SEDMT CONT FENCE (INSTALL)

LF 4,600.000 23 DOLLARS

and CENTS

506 7041

TEMP SEDMT CONT FENCE (REMOVE)

LF 4,600.000 24 DOLLARS

and CENTS

529 7002

CONC CURB (TY II)

LF 36.000 25 DOLLARS

and CENTS

529 7009

CONC CURB & GUTTER (TY II)

LF 116.500 26 DOLLARS

2-3

BROWN FORM 234-B I-61-5M

TxDOT PROJECT

COUNTY

ALT

ITEM-CODE

UNIT BID PRICE ONLY.

WRITTEN IN WORDS UNIT APPROX

QUANTITIES

DEPT

USE

ONLY

ITEM

NO.

DESC

CODE

S.P.

No.

529 7029

CONC CURB (TY I) (MOD)

LF 120.000 27 DOLLARS

and CENTS

644 7001

IN SM RD SN SUP&AM TY10BWG(1)SA(P)

EA 11.000 28 DOLLARS

and CENTS

666 7084

REFL PAV MRK TY I (W)(SYMBOL)(100MIL)

EA 10.000 29 DOLLARS

and CENTS

666 7244

RE PM TY III (W)(24")(SLD)

LF 48.000 30 DOLLARS

and CENTS

666 7347

PAVEMENT SLER 6"

LF 342.000 31 DOLLARS

and CENTS

666 7363

PAVEMENT SLER (SYMBOL)

EA 2.000 32 DOLLARS

and CENTS

666 7542

RE PM TY III (W)6"(SLD)(PU)

LF 5,602.000 33 DOLLARS

and CENTS

666 7544

RE PM TY III (Y)6"(SLD)(PU)

LF 24,528.000 34 DOLLARS

and CENTS

672 7004

REFL PAV MRKR TY II-A-A

EA 308.000 35 DOLLARS

and CENTS

678 7002

PAV SURF PREP FOR MRK (6")

LF 342.000 36 DOLLARS

and CENTS

678 7021

PAV SURF PREP FOR MRK (SYMBOL)

EA 2.000 37 DOLLARS

3-3

CERTIFICATION OF INTEREST IN OTHER BID

PROPOSALS FOR THIS WORK

By signing this proposal, the bidding firm and the signer certify that the following information, as indicated by checking “Yes” or “No” below, is true, accurate, and complete.

A. Quotation(s) have been issued in this firm's name to other firm(s) interested in this work for consideration for performing a portion of this work.

________ YES

________ NO

B. If this proposal is the low bid, the bidder agrees to provide the following information prior to award of the contract.

1. Identify firms which bid as a prime contractor and from which the bidder received quotations for work on this project.

2. Identify all the firms which bid as a prime contractor to which the bidder gave quotations for work on this project.

ENGINEER SEAL

Project C 923-6-68, ETC

Highway PW County BROWN

The enclosed Texas Department of Transportation Specifications, Special Specifications, Special Provisions, General Notes and Specification Data in this document have been selected by me, or under my responsible supervision as being applicable to this project.

Alteration of a sealed document without proper notification to the responsible engineer is an offense under the Texas Engineering Practice Act.

The seal appearing on this document was authorized by:

Jason H. Scantling P.E.

August 26, 2026

Seal Applies to CSJ(s):

All CSJs within the Contract

96633

Jason H. Scantling

County: Brown

Highway: PW Control: 0923-06-068, ETC

General Notes Sheet A

GENERAL NOTES

TEST TO BE IN ACCORDANCE WITH

TEXAS DEPARTMENT OF TRANSPORTATION

STANDARD TEST METHODS.

Item

Description

Soil Constants

Max

LL.

Max.

PI

Min.

PI

* 132 Embankment (Final)(Dens Cont)(Ty C) 40 25 3 247 Fl Bs (Cmp In Plc) (Ty A Gr 4)(Fnal Pos) 3

* Applies to borrow only.

Job control samples for gradation and P.I. testing will be taken from the windrow after blade mixing.

CSJ 0923-06-068 Asphalt Surface Areas-SY Item Description Course Seal Coat Camping

Loops Pavement

Repair 310 MC-30 Prime 7,156 316 Asph (AC-20-5TR) 1st 69,201 27,573 7,156 316 Aggr Ty-B GR 4 SAC-B (MOD) 1st 69,201 27,573 7,156 344 Superpave Mixtures SP-D SAC-B PG 76-22 Final 31,887

Basis of Estimate

Item Description Rate SY Quantity 310 MC-30 0.30 Gal/SY 7,156 2,147 Gal 316 Asph (AC-20-5TR) 0.34 Gal/SY 103,930 35,336 Gal 316 Aggr TY-B GR 4 SAC-B (MOD) 110 CY/SY 103,930 945 CY 344 1.5” Superpave Mixtures SP-D SAC-B PG 76-22 115 lbs/sy/in 31,887 2751 Tons

CSJ 0923-06-067 Asphalt Surface Areas-SY

Item Description Course Muse

WMA

316 Asph (AC-20-5TR) 1st 5,170 316 Aggr Ty-B GR 4 SAC-B (MOD) 1st 5,170

Basis of Estimate

Item Description Rate SY Quantity 316 Asph (AC-20-5TR) 0.34 Gal/SY 5,170 1,758 Gal 316 Aggr TY-B GR 4 SAC-B (MOD) 110 CY/SY 5,170 47 CY

General Notes Sheet B

Environmental

The Contractor will not be allowed to store equipment, materials, incidentals, hazardous chemicals, petroleum products, concrete washouts, etc. in the Department’s R.O.W. without written permission from the Engineer.

1. The contractor is required to coordinate with the Texas Parks and Wildlife Department and adjust construction efforts with the daily operations of the park. Establishment of any material and/or equipment staging or storage areas other than those shown on the plans must be approved by the engineer and the park superintendent prior to the start of work and thereafter if a change of location becomes necessary." As part of this coordination the contractor will be required to:

a. Hold a weekly meeting with a TxDOT representative, the park superintendent, and the contractor's superintendent to review and discuss the construction work and traffic control procedures planned for the following two week period.

b. Schedule work so that no more than one area is under construction at a time. Once construction is started in an area, work must be performed continuously until all work is completed within the given area before construction in another subsequent area will be allowed to begin. Any request to sequence work in an otherwise manner must be obtained by written approval of the engineer and the park superintendent.

c. Provide written notification to both the engineer and the park superintendent at least two weeks prior to opening up any new construction locations within the park."

d. Prior to the start of construction, the limits of the work area are delineated with stakes and flagging to identify where non-work areas begin so that damage to adjacent park property by construction equipment and other vehicles is avoided.

e. Not be authorized to work on weekends or major holidays without prior written approval of both the engineer and the park superintendent.

f. Mitigate or replace unnecessary damage to trees or shrubs within and adjacent to the limits of construction. The contractor shall replace or mitigate damaged trees or shrubs with like size and types of trees or shrubs damaged. Final determination of the replacement or mitigation requirements will be determined by the TxDOT Landscape Architect. All costs associated with the replacement or mitigation cost will be the responsibility of the contractor.

g. Repair or replace any unnecessary damage to arbors or utilities within and adjacent to the limits of construction. Any replacement cost will be the responsibility of the contractor.

h. If any archeological materials are found on site during construction, all work must stop immediately and TPWD must be contacted for guidance.

General Notes Sheet C

i. No heavy equipment will be utilized within 2' of any historic stone curbs/structures encountered within project construction limits. All work within 2' will be done with hand tools/equipment only. Stone curbing to be protected with burlap and/or other approved materials to ensure no damage or staining occurs. Any stone inspected by TPWD and noted to have incurred damage within timeline of project will be repaired at the contractor’s expense.

TEXAS ONE CALL

Fiber optic cable systems, gas lines, underground power lines, water lines, sewer lines, and other various utilities may be buried within the project limits. Protection of these utility systems is of extreme importance since any break could disrupt service to users resulting in business interruption and loss of revenue and profits. The Contractor will telephone Texas One Call at 1-800-344-8377 (a 24-hour number), to determine if utilities are buried anywhere on the project in accordance with all UNDERGROUND FACILITY DAMAGE PREVENTION AND SAFETY laws. This action; however, will in no way be interpreted as relief of responsibilities under the terms of the Contract as set out in the plans and specifications. Coordinate the repair of all damages caused by daily operations and have facilities restored to service in a timely manner as directed at no additional cost to TxDOT.

GENERAL

Unless specifically noted as applying to only a certain project or projects, these general notes will apply to all projects associated to this contract.

Contractor questions on this project are to be addressed to the following individual(s):

Name Email Address

Blake Stembridge, P.E. Blake.Stembridge@txdot.gov

Nathan McMahon, Engineering Assistant Nathan.Mcmahon@txdot.gov

Contractor questions will be accepted through email, phone, and in person by the above individual(s).

Questions may also be submitted via the Letting Pre-Bid Q&A web page. This webpage can be accessed from the Notice to Contractors dashboard located at the following Address:

https://tableau.txdot.gov/views/ProjectInformationDashboard/NoticetoContractors

All contractor questions will be reviewed by the Engineer. All questions and any corresponding responses that are generated will be posted through the same Letting Pre-Bid Q&A web page.

The Letting Pre-Bid Q&A web page for each project can be accessed by using the dashboard to navigate to the project you are interested in by scrolling or filtering the dashboard using the controls on the left. Hover mailto:Blake.Stembridge@txdot.gov mailto:Nathan.Mcmahon@txdot.gov https://tableau.txdot.gov/views/ProjectInformationDashboard/NoticetoContractors

General Notes Sheet D over the blue hyperlink for the project you want to view the Q&A for and click on the link in the window that pops up.

The term “Article” or “Section” referred to hereon is defined in the forward of the Standard Specifications for Construction and Maintenance of Highways, Streets, And Bridges adopted by the Texas Department of Transportation September 1, 2024..

The Contractor's responsibility toward preparing the pavement for seal coat on all projects with no curb and gutter will be limited to normal sweeping with the usual rotary-broom equipment. All grass, weeds, etc. at the pavement edges will be removed by contractor.

The Contractor’s responsibility toward preparing the pavement for seal coat with curb and gutter will be normal sweeping with the usual rotary-broom equipment. After the placement of the Seal Coat, trash, dirt, and excess rock will be removed from the curb and gutter and sidewalks in manner approved by the Engineer.

All roadway and intersections will be swept after each roadway is completed or as directed by the Engineer.

ITEM 5 CONTROL OF WORK

A precast concrete alternate may be submitted in accordance with the latest version of the Bridge Design Manual – LRFD. The Contractor must submit the alternate design for review and approval. Acceptance or denial of an alternate is at the sole discretion of the Engineer. All alternate designs must be signed and sealed by a Professional Engineer. Impacts to the project schedule and any additional costs resulting from the use of alternates are the sole responsibility of the Contractor.

ITEM 7 LEGAL RELATIONS AND RESPONSIBILITIES

Roadway closures during the following key dates and/or special events are prohibited:

Muse WMA No work Dates 2026-2027 Sept. 1-Oct. 11 Oct. 19-23 Nov. 16-22 Dec. 12-13 Dec. 19-22 Jan. 2-7 Jan. 9-10 April 6-8 April 13-15

General Notes Sheet E

ITEM 8 PROSECUTION AND PROGRESS

Working days will be computed and charged in accordance with Section 8.3.1.2. “Standard Workweek”.

Work will not be performed without time being charged.

Working day charges will be in accordance with SP 008---010 (90 calendar days after the date of the written authorization to begin work. Do not begin any work before the end of this period unless authorized in writing by the Engineer.) This delay is for production of base material and test submittals for approval and to coordinate with Parks and Wildlife also helps getting out of the peak season for the parks.

PROJECT SCHEDULES

Bar Char scheduling will be required to be submitted and maintained monthly by the Contractor unless otherwise directed by the Engineer. (8.5.5.1.)

ITEM 104 REMOVING CONCRETE

The Contractor will make a 1” cut to use as a guide before full depth cutting. Saw-Cut the full depth through the concrete before existing concrete removal.

ITEM 132 EMBANKMENT

Refer to Item 210 “Rolling” for additional roller requirements.

“Final” embankment that is not accounted for in the cross section(s) or typical section(s) but that has been estimated or shown for informational purposes, e.g., additional areas under guard fence, around S.E.T.s, etc.; will be measured in its final position as defined in Section 132.4.1. Shrinkage or swell factors will not be considered in determining the calculated quantities.

ITEM 247 FLEXIBLE BASE

For projects with an ACP overlay, IRI measurements will required on the flexible base surface using Surface Test Type B and corrective action will be required for IRI values greater than 100 in. per mile.

Refer to Item 210 for additional roller requirements.

Ride quality will be measured before the application of prime coat unless otherwise approved in writing by the Engineer.

A grader (a road grader, a blade, a maintainer, or a motor grader) will be used to process base unless otherwise approved by the Engineer.

General Notes Sheet F

Place new flexible base in lifts of approximately equal depth not to exceed 6 inches unless otherwise directed.

PROPERTY Grade 4 Master gradation sieve size (cumulative % retained) -----

2-1/2" 0 1-3/4" 0-10 7/8" ----- 3/8" ----- #4 45-75 #40 50-85 Liquid Limit, % Max 40 Plasticity Index, Max 14 Plasticity Index, Min 3 Wet ball mill, % Max ----- Wet ball mill, % Max increase passsing the # 40 sieve -----

Min compressive strength, psi -----lateral pressure 0 psi -----lateral pressure 3 psi -----lateral pressure 15 psi -----

ITEM 310 PRIME COAT

The IRI data is to be provided 3 days prior to priming.

Cure prime placed with a cutback asphalt binder for 10 days before placing subsequent surface courses unless otherwise directed by the Engineer.

Finished base must be dampened before the application of a cutback asphalt binder is placed. This work will not be paid for directly but will be considered subsidiary to Item 310.

ITEM 316 SURFACE TREATMENTS

Table 2 Aggregate Gradation Requirements (Cumulative % Retained1)

Sieve Grade

4(MOD)

1'' - 7/8'' -

General Notes Sheet G

3/4'' - 5/8'' 0 1/2'' 0-15 3/8'' 45-85 1/4'' - #4 95-100 #8 98-100

The Department will witness the Transverse Distribution Test Tex-922-K, Part III. In accordance with Section 316.3.1.3.1, the type and grade of asphalt will be used to run the test unless otherwise directed by the Engineer. Paper or digital copies of all tests will be required before work begins.

In addition to other asphalt distributor requirements, the asphalt distributor will be capable of providing a transversely varied asphalt rate. The Contractor will demonstrate that the distributor can apply an asphalt rate outside of the wheel path locations between 22 and 32 percent higher than the asphalt rate being applied in the wheel paths. The Contractor’s calibration of the distributor will include verification of this capability and a description of the spray bar(s) and nozzles to be used. The percentage difference in the asphalt rate provided by each tested spray bar and nozzle arrangement will be provided to the Engineer.

The Engineer will select the pavements where the transversely varied asphalt rates are to be provided.

All precoated aggregate will use PG 76-22 asphalt.

Furnish aggregate with a minimum B surface aggregate classification.

The asphalt and aggregate rates shown hereon are for average conditions. The rate may be varied as determined by the Engineer to obtain proper embedment of aggregate.

If tracking of asphalt material is noticed while placing aggregate, the contractor will be required to use additional rock as directed by the Engineer.

Before stockpiling aggregate, the contractor will be required to provide TxDOT with stockpile locations and a sequence of work for each reference.

Protect all exposed concrete surfaces within the limits of this project(s), as much as practical, from asphalt materials by any means approved by the Engineer at the contractor’s expense.

The Contractor will be required to leave barricades in place at all stockpile locations until all remaining aggregate has been removed unless otherwise directed by the Engineer.

Use a medium pneumatic roller meeting the requirements of Item 210 as directed by the Engineer. This work will be subsidiary to the various bid items.

General Notes Sheet H

ITEM 344 SUPERPAVE MIXTURES

Binder substitution is not allowed.

RAS will not be allowed.

No more than 5% RAP will be allowed.

Belly dumps will not be allowed if a spray paver is used.

See item 504 for additional structure requirements located at HMAC plant(s).

ITEM 351 FLEXIBLE PAVEMENT STRUCTURE REPAIR

The contractor will mark locations of flexible pavement repair for approval by the Engineer before starting work on the repair areas.

Locations may be changed and/or added as directed by the Engineer.

For maintaining the existing pavement during construction, 6” of flex base and a seal coat will be used unless otherwise approved.

ITEM 401 FLOWABLE BACKFILL

All flowable backfill will be “Non-Excavatable” unless otherwise specified

ITEM 420 CONCRETE SUBSTRUCTURES

Culverts will be constructed in conjunction with roadway construction phasing, unless otherwise directed by the Engineer.

ITEM 427 SURFACE FINISHES FOR CONCRETE

Surface Area II will receive a rub finish.

ITEM 502 BARRICADES, SIGNS, AND TRAFFIC HANDLING

The Contractor will be required to keep all TCP devices clean. If notified by the Engineer to clean the TCP devices, the Contractor will have until the end of that daylight period to comply. Failure to comply will result in a suspension of all work until the TCP devices are clean. Time will not be suspended

The Contractor Force Account “Safety Contingency” that has been established for this project is intended to be utilized for work zone enhancements, to improve the effectiveness of the Traffic Control Plan, that could not be foreseen in the project planning and design stage. These enhancements will be mutually agreed

General Notes Sheet I upon by the Engineer and the Contractor’s Responsible Person based on weekly or more frequent traffic management reviews on the project

In case of inclement weather during daylight hours while the Contractor is still on the project, it will be the responsibility of the Contractor to handle traffic in a manner to minimize any damage to the seal coat.

ITEM 503 PORTABLE CHANGEABLE MESSAGE SIGN

1 portable changeable message signs are estimated for this project and will be placed as directed by the Engineer. (1 PCMB X 4 Days = 4 TOTAL )

ITEM 504 FIELD OFFICE AND LABORATORY

One Type D Structure (Asphalt Mix Control Laboratory) will be required for this project.

ITEM 505 TRUCK MOUNTED ATTENUATOR (TMA) AND TRAILER ATTENUATOR (TA)

Provide the number of vehicles with truck mounted attenuators (TMA) listed in the table below. The Contractor will be responsible for determining if one or more of these operations will be ongoing at the same time to determine the total number of TMAs needed for the project.

STANDARD / PHASE # TMA'S REQUIRED

TCP(2-2) 1

TCP(3-1) 1

Stationary shadow vehicle(s) with TMA are estimated at 2 days for the entire project.

Mobile shadow vehicle(s) with TMA are estimated at 4 days for this project.

ITEM 506 TEMPORARY EROSION, SEDIMENTATION, AND ENVIRONMENTAL CONTROLS

The Contractor should anticipate multiple mobilizations for the installation of BMP’s on this project.

The Engineer will determine actual time and placement locations of BMP's and temporary measures.

Contractor will not install BMPs until locations are approved by the Engineer.

Stockpile sites may be cleared of cover vegetation, but the vegetation root system will not be destroyed.

General Notes Sheet J

ITEM 529 CONCRETE CURB, GUTTER, AND COMBINED CURB AND GUTTER

Reinforcing steel will be required in all curb and gutter.

Construct tooled joints every 5’ corresponding to the joints in the sidewalk where applicable or as directed by the Engineer.

Construct expansion joints every 40’ to correspond to the sidewalk expansion joints or as directed by the Engineer.

ITEM 644 SMALL ROADSIDE SIGN ASSEMBLIES

Upon completion of site repairs, the Contractor shall install and maintain temporary handicap (ADA) signage at all designated locations until final signing and pavement striping are complete.

The Contractor will notify the Engineer 5 working days before installing any sign base. The Engineer will coordinate with the Contractor and the Maintenance office to assure proposed sign placements are in accordance with the current version of the Sign Crew Field Book and the TMUTCD. Any signs that are placed without this coordination by the Contractor that are not located correctly will be removed and relocated at the Contractor’s expense.

See the MPL for approved Slip Bases.

https://www.txdot.gov/content/dam/docs/division/mtd/mpl/slipbase.pdf

Build signs not detailed in the plans according to the latest edition of the Standard Highway Sign Designs for Texas.

Conformable Retroreflective Sheeting in accordance with DMS 8300 will be required on all Warning, Stop, and Yield signs. Retroreflective sheeting wrapped around a sign support is yellow unless the sign on the support is a Stop or Yield, in which case the sheeting will be red. Retroreflective sheeting will have a height on the post of 12 inches and the bottom of the sheeting will be 4 feet above the edge of the travel lane.

Retroreflective sheeting will not be paid for directly but will be considered subsidiary to Item 644 Small Roadside Sign Assemblies.

ITEM 666 RETROREFLECTORIZED PAVEMENT MARKINGS

TxDOT shall verify all passing and no passing zones locations before final striping is placed.

Sealed roadways will be allowed to cure for 3 days before final striping is placed unless otherwise directed by the Engineer.

https://www.txdot.gov/content/dam/docs/division/mtd/mpl/slipbase.pdf

Control : 0923-06-068, ETC Project : C 923-6-68, ETC

BROWN

PWHighway :

County :

TEXAS DEPARTMENT OF TRANSPORTATION

GOVERNING SPECIFICATIONS AND SPECIAL PROVISIONS

ALL SPECIFICATIONS AND SPECIAL PROVISIONS APPLICABLE TO THIS PROJECT ARE

IDENTIFIED AS FOLLOWS:

SPECIAL PROVISIONS :

SPECIAL PROVISIONS WILL GOVERN AND TAKE PRECEDENCE OVER

THE SPECIFICATIONS ENUMERATED HEREON WHEREVER IN

CONFLICT THEREWITH.

STANDARD SPECIFICATIONS:

PREPARING RIGHT OF WAY(103) (752) ITEM 100

REMOVING CONCRETEITEM 104

EXCAVATION(132) ITEM 110

EMBANKMENT(100) (110) (160) (204) (210) (216) (400) ITEM 132

ROADSIDE AMENITYITEM 194

PROOF ROLLING(210) ITEM 216

PRIME COAT(300) (316) ITEM 310

SEAL COAT(210) (300) (302) (341) (520) ITEM 316

SUPERPAVE MIXTURES(300) (301) (320) (504) (520) (585) ITEM 344

FLEXIBLE PAVEMENT STRUCTURE REPAIR(132) (204) (247) (260) (275) (276)

(292) (310) (316) (330) (334) (341)

ITEM 351

FLOWABLE BACKFILL(421) ITEM 401

CONCRETE SUBSTRUCTURES(400) (404) (421) (422) (426) (427) (440) (441)

(448)

ITEM 420

MOBILIZATIONITEM 500

BARRICADES, SIGNS, AND TRAFFIC HANDLING(503) (505) (510) ITEM 502

PORTABLE CHANGEABLE MESSAGE SIGNITEM 503

FIELD OFFICE AND LABORATORYITEM 504

TRUCK-MOUNTED ATTENUATOR (TMA) AND TRAILER ATTENUATOR (TA)ITEM 505

TEMPORARY EROSION, SEDIMENTATION, AND ENVIRONMENTAL CONTROLS

(161) (432) (556)

ITEM 506

CONCRETE CURB, GUTTER, AND COMBINED CURB AND GUTTER(360) (420)

(421) (440)

ITEM 529

SMALL ROADSIDE SIGN ASSEMBLIES(421) (440) (441) (442) (445) (636) (656) ITEM 644

RETROREFLECTORIZED PAVEMENT MARKINGS(316) (502) (662) (667) (677)

(678)

ITEM 666

RAISED PAVEMENT MARKERS(677) (678) ITEM 672

PAVEMENT SURFACE PREPARATION FOR MARKINGS(677) ITEM 678

ITEMS 1-9 INCL., GENERAL REQUIREMENTS AND COVENANTS

ADOPTED BY THE TEXAS DEPARTMENT OF TRANSPORTATION

SEPTEMBER 1, 2024.

STANDARD SPECIFICATIONS ARE INCORPORATED INTO THE

CONTRACT BY REFERENCE.

WAGE RATES

1-2

GENERAL :

THE ABOVE-LISTED SPECIFICATIONS ITEMS ARE THOSE UNDER WHICH

PAYMENT IS TO BE MADE. THESE, TOGETHER WITH SUCH OTHER PERTINENT

ITEMS, IF ANY, AS MAY BE REFERRED TO IN THE ABOVE-LISTED

SPECIFICATION ITEMS, AND INCLUDING THE SPECIAL PROVISIONS LISTED

ABOVE, CONSTITUTE THE COMPLETE SPECIFICATIONS FOR THIS PROJECT.

SPECIAL SPECIFICATIONS :

"SPECIAL LABOR PROVISIONS FOR STATE PROJECTS (000---

005)" (000---005)

SPECIAL PROVISION

"NONDISCRIMINATION" (000---001) SPECIAL PROVISION

"CERTIFICATE OF INTERESTED PARTIES (FORM 1295)" (000---017) SPECIAL PROVISION

"SMALL BUSINESS ENTERPRISE IN STATE-FUNDED PROJECTS" (000

---019)

SPECIAL PROVISION

"NOTICE OF CONTRACTOR PERFORMANCE EVALUATIONS" (000---

125)

SPECIAL PROVISION

"SCHEDULE OF LIQUIDATED DAMAGES" (000---224) SPECIAL PROVISION

(002---004) SPECIAL PROVISION TO ITEM 002

(003---006) SPECIAL PROVISION TO ITEM 003

(007---001) SPECIAL PROVISION TO ITEM 007

(008---010) SPECIAL PROVISION TO ITEM 008

(009---002) SPECIAL PROVISION TO ITEM 009

(247---001) SPECIAL PROVISION TO ITEM 247

(260---001) SPECIAL PROVISION TO ITEM 260

(275---001) SPECIAL PROVISION TO ITEM 275

(292---001) SPECIAL PROVISION TO ITEM 292

(300---003) SPECIAL PROVISION TO ITEM 300

(440---002) SPECIAL PROVISION TO ITEM 440

(666---002) SPECIAL PROVISION TO ITEM 666

(672---001) SPECIAL PROVISION TO ITEM 672

2-2

Highway PW County BROWN

SMALL BUSINESS ENTERPRISE REQUIREMENTS

The following goal for small business enterprises is established:

SBE

0%

CHILD SUPPORT STATEMENT

Under section 231.006, Family Code, the vendor or applicant certifies that the individual or business entity named in this contract, bid, or application is not ineligible to receive the specified grant, loan, or payment and acknowledges that this contract may be terminated and payment may be withheld if this certification is inaccurate.

CONFLICT OF INTEREST CERTIFICATION

Pursuant to Texas Government Code Section 2261.252(b), the Department is prohibited from entering into contracts in which Department officers and employees have a financial interest.

By signing the Contract, the Contractor certifies that it is not prohibited from entering into a Contract with the Department as a result of a financial interest as defined under Texas Government Code Section 2261.252(b), and that it will exercise reasonable care and diligence to prevent any actions or conditions that could result in a conflict of interest with the Department.

The Contractor also certifies that none of the following individuals, nor any of their family members within the second degree of affinity or consanguinity, owns 1% or more interest or has a financial interest as defined under Texas Government Code Section 2261.252(b) in the Contractor:

Any member of the Texas Transportation Commission; and The Department’s Executive Director, General Counsel, Chief of Procurement and Field Support

Operations, Director of Procurement, and Director of Contract Services.

Violation of this certification may result in action by the Department.

E-VERIFY CERTIFICATION

Pursuant to Texas Transportation Code §223.051, all TxDOT contracts for construction, maintenance, or improvement of a highway must include a provision requiring Contractors and subcontractors to use the U.S. Department of Homeland Security’s E-Verify system to determine employment eligibility. By signing the contract, the Contractor certifies that prior to the award of the Contract:

the Contractor has registered with and will, to the extent permitted by law, utilize the United States Department of Homeland Security’s E-Verify system during the term of the Contract to determine the eligibility of all persons hired to perform duties within Texas during the term of the agreement; and the Contractor will require that all subcontractors also register with and, to the extent permitted by law, utilize the United States Department of Homeland Security’s E-Verify system during the term of the subcontract to determine the eligibility of all persons hired to perform duties within Texas during the term of the agreement.

Violation of this requirement constitutes a material breach of the Contract, subjects a subcontractor to removal from the Contract, and subjects the Contractor or subcontractors to possible sanctions in accordance with Title 43, Texas Administrative Code, Chapter 10, Subchapter F, “Sanctions and Suspension for Ethical Violations by Entities Doing Business with the Department.”

_BPSDocName 1-1

Certification Regarding Disclosure of Public Information Pursuant to Subchapter J, Chapter 552, Texas Government Code, contractors executing a contract with a governmental body that results in the expenditure of at least $1 million in public funds must:

1) preserve all contracting information* as provided by the records retention requirements applicable to Texas Department of Transportation (TxDOT) for the duration of the contract,

2) on request of TxDOT, promptly provide any contracting information related to the contract that is in the custody or possession of the entity, and

3) on completion of the contract, either:

A. provide, at no cost to TxDOT, all contracting information related to the contract that is in the custody or possession of the entity, or B. preserve the contracting information related to the contract as provided by the records retention requirements applicable to TxDOT

The requirements of Subchapter J, Chapter 552, Government Code, may apply to this contract, and the contractor or vendor agrees that the contract can be terminated if the contractor or vendor knowingly or intentionally fails to comply with a requirement of that subchapter.

By entering into Contract, the Contractor agrees to:

• provide, or make available, to TxDOT and any authorized governmental investigating or auditing agency all records, including electronic and payment records related to the contract, for the same period provided by the records retention schedule applicable to TxDOT, and

• ensure that all subcontracts include a clause requiring the same.

* As defined in Government Code §552.003, “Contracting information” means the following information maintained by a governmental body or sent between a governmental body and a vendor, contractor, potential vendor, or potential contractor:

1) information in a voucher or contract relating to the receipt or expenditure of public funds by a governmental body;

2) solicitation or bid documents relating to a contract with a governmental body;

3) communications sent between a governmental body and a vendor, contractor, potential vendor, or potential contractor during the solicitation, evaluation, or negotiation of a contract;

4) documents, including bid tabulations, showing the criteria by which a governmental body evaluates each vendor, contractor, potential vendor, or potential contractor responding to a solicitation and, if applicable, an explanation of why the vendor or contractor was selected; and

5) communications and other information sent between a governmental body and a vendor or contractor related to the performance of a final contract with the governmental body or work performed on behalf of the governmental body.

CERTIFICATION TO NOT BOYCOTT ISRAEL

Pursuant to Texas Government Code §2271.002, the Department must include a provision requiring a written verification affirming that the Contractor does not boycott Israel, as defined in Government Code §808.001, and will not boycott Israel during the term of the contract. This provision applies to a contract that:

1) is with a Contractor that is not a sole proprietorship,

2) is with a Contractor with 10 or more full-time employees, and

3) has a value of $100,000 or more.

By signing the contract, the Contractor certifies that it does not boycott Israel and will not boycott Israel during the term of this contract. “Boycott” means refusing to deal with, terminating business activities with, or otherwise taking any action that is intended to penalize, inflict economic harm on, or limit commercial relations specifically with Israel, or with a person or entity doing business in Israel or in an Israeli-controlled territory, but does not include an action made for ordinary business purposes.

CERTIFICATION TO NOT BOYCOTT ENERGY COMPANIES

Pursuant to Texas Government Code §2274.002, the Department must include a provision requiring a written verification affirming that the Contractor does not boycott energy companies, as defined in Government Code §809.001, and will not boycott energy companies during the term of the contract. This provision applies to a contract that:

1) is with a Contractor that is not a sole proprietorship,

2) is with a Contractor with 10 or more full-time employees, and

3) has a value of $100,000 or more.

By signing the contract, the Contractor certifies that it does not boycott energy companies and will not boycott energy companies during the term of this contract. “Boycott” means taking any action that is intended to penalize, inflict economic harm on, or limit commercial relations with a company because the company: (1) engages in the exploration, production, utilization, transportation, sale, or manufacturing of fossil fuel-based energy and does not commit or pledge to meet environmental standards beyond applicable federal and state law; or (2) does business with a company described by (1).

CERTIFICATION TO NOT DISCRIMINATE AGAINST

FIREARM ENTITIES OR FIREARM TRADE ASSOCIATIONS

Pursuant to Texas Government Code §2274.002, the Department must include a provision requiring a written verification affirming that the Contractor:

1) does not have a practice, policy, guidance, or directive that discriminates against a firearm entity or firearm trade association, as defined in Government Code §2274.001, and

2) will not discriminate against a firearm entity or firearm trade association during the term of the contract.

This provision applies to a contract that:

1) is with a Contractor that is not a sole proprietorship,

2) is with a Contractor with 10 or more full-time employees, and

3) has a value of $100,000 or more.

By signing the contract, the Contractor certifies that it does not discriminate against a firearm entity or firearm trade association as described and will not do so during the term of this contract. "Discriminate against a firearm entity or firearm trade association" means, with respect to the entity or association, to:

(1) refuse to engage in the trade of any goods or services with the entity or association based solely on its status as a firearm entity or firearm trade association; (2) refrain from continuing an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association; or (3) terminate an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association. "Discriminate against a firearm entity or firearm trade association" does not include: (1) the established policies of a merchant, retail seller, or platform that restrict or prohibit the listing or selling of ammunition, firearms, or firearm accessories; (2) a company’s refusal to engage in the trade of any goods or services, decision to refrain from continuing an existing business relationship, or decision to terminate an existing business relationship to comply with federal, state, or local law, policy, or regulations or a directive by a regulatory agency, or for any traditional business reason that is specific to the customer or potential customer and not based solely on an entity ’s or association’s status as a firearm entity or firearm trade association.

FOREIGN ADVERSARIES REQUIREMENTS

Pursuant to Executive Order No. GA-48 relating to the hardening of state government, TxDOT must require any company that submits a bid or proposal with respect to a contract for goods or services to the Department to certify that the company, and, if applicable, any of its holding companies or subsidiaries, is not:

A. Listed in Section 889 of the 2019 National Defense Authorization Act (NDAA); or

B. Listed in section 1260H of the 2021 NDAA; or

C. Owned by the government of a country on the U.S. Department of Commerce foreign adversaries list under 15 C.F.R. 791.4; or

D. Controlled by any governing or regulatory body located in a country on the U.S. Department of Commerce’s foreign adversaries list under 15 C.F.R. 791.4.

By signing this proposal, the Contractor certifies that neither it nor any affiliated entities are:

• Listed in Section 889 of the 2019 NDAA;

• Listed in Section 1260H of the 2021 NDAA;

• Owned by the government of a country listed under 15 C.F.R. 791.4; or

• Controlled by any governing or regulatory body located in a country listed under 15 C.F.R.

791.4

_BPSDocName 1-1

PROHIBITION ON CERTAIN TELECOMMUNICATIONS

EQUIPMENT OR SERVICES

The Federal Register Notice issued the Final Rule and states that the amendment to 2 CFR

200.216 is effective on August 13, 2020. The new 2 CFR 200.471 regulation provides clarity that the telecommunications and video surveillance costs associated with 2 CFR 200.216 are unallowable for services and equipment from these specific providers. OMB’s Federal Register Notice includes the new 2 CFR 200.216 and 2 CFR 200.471 regulations.

https://www.federalregister.gov/documents/2020/08/13/2020-17468/guidance-for-grants-and-agreements Per the Federal Law referenced above, use of services, systems, or services or systems that contain components produced by any of the following manufacturers is strictly prohibited for use on this project. Therefore, for any telecommunications, CCTV, or video surveillance equipment, services or systems cannot be manufactured by, or have components manufactured by:

• Huawei Technologies Company,

• ZTE Corporation (any subsidiary and affiliate of such entities),

• Hyatera Communications Corporation,

• Hangzhou Hikvision Digital Technology Company,

• Dahua Technology Company (any subsidiary and affiliate of such entities).

Violation of this prohibition will require replacement of the equipment at the contractor’s e xpense.

Prohibited Activities by Contractors and Vendors

Pursuant to Texas Government Code 2261.302, a state agency contractor, subcontractor, or vendor responding to a contract solicitation may not directly or indirectly:

(1.) engage in surveillance targeting:

(a.) a member of the state legislature or a person employed to support the state legislature in any capacity, (b.) a family member of a person described in subsection (a), (c.) a state agency employee, or (d.) an individual making a complaint or raising concerns regarding state agency operations or contracting;

(2.) engage in an act of intimidation, coercion, extortion, undue influence, or other similar conduct intended to influence, silence, or retaliate against a person described in subsection (1) above, or;

(3.) use private or confidential information to manipulate or influence a state contracting decision or proceeding.

By signing this proposal, the bidder certifies that it will not engage in surveillance targeting or an act of intimidation, coercion, extortion, undue influence, or other similar conduct intended to influence, silence, or retaliate against a member of the state legislature, a person employed to support the state legislature in any capacity, a family member of an aforementioned person, a state agency employee, or an individual making a complaint or raising concerns regarding state agency operations or contracting.

Furthermore, the bidder certifies that it will not use private or confidential information to manipulate or influence a state contracting decision or proceeding.

CLASS. # CLASSIFICATION DESCRIPTION

ZONE

TX46

*(TX20260046)

ZONE

TX51

*(TX20260051)

ZONE

TX55

*(TX20260055)

ZONE

TX291

*(TX20260291)

ZONE

TX292

*(TX20260292)

ZONE

TX293

*(TX20260293)

ZONE

TX294

*(TX20260294)

ZONE

TX295

*(TX20260295)

ZONE

TX296

*(TX20260296)

ZONE

TX297

*(TX20260297)

ZONE

TX298

*(TX20260298)

ZONE

TX299

*(TX20260299)

ZONE

TX300

*(TX20260300)

1106 Asphalt Raker $18.97 $15.02 $18.76 $19.40 $18.20 $16.28 $19.87 $19.53 $17.40 $15.22 $19.58 $20.41 $19.02 1124 Concrete Finisher, Paving and Structures $20.92 $19.13 $21.11 $20.61 $18.72 $17.99 $22.48 $20.66 $21.16 $18.15 $20.77 $20.79 $20.04 1139 Electrician $23.70 $30.54 $25.73 $36.10 $32.38 $31.46 1143 Telecommunication Technician $23.14 1145 Traffic Signal/Light Pole Worker $25.43 $21.99 1150 Flagger $13.50 $14.56 $15.30 $15.52 $15.00 $14.80 $13.99 $14.59 $15.81 $14.82 $16.63 $15.16 1151 Form Builder/Setter, Structures $21.78 $18.59 $19.31 $20.63 $20.18 $19.37 $22.50 $20.05 $19.82 $18.26 $22.09 $19.93 $19.89 1160 Form Setter, Paving & Curb $20.39 $17.31 $18.50 $19.18 $20.89 $18.25 $18.16 $17.56 $19.44 $19.32…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .