Part_10_-_Toe_Seep_Modifications_Plans_and_Specs_4-7-2015.pdf

Maintenance

198 35010372 9/2007

Regular Cleaning

Cleaning the display

When the surface or the frame of the display gets dirty, soak a soft cloth in water with a neutral detergent, wring the cloth tightly, and wipe the display.

Do not use hard or pointed objects to operate the touch-screen panel, since it can damage the panel surface.

Do not use paint thinner, organic solvents, or a strong acid compound to clean the unit.

Cleaning the Gasket

The gasket protects the unit and improves its water resistance.

Change the gasket at least once a year, or as soon as scratches or dirt become visible.

During normal maintenance and reinstallation, check the gasket for dirt and scratches.

Inserting the Gasket

The gasket must be inserted correctly into the groove to comply with IP65.

The upper surface of the gasket should protrude approximately 2 mm [0.08 inch] out from the groove. Verify that the gasket is correctly inserted before installing the unit into a panel.

Note: Be sure the gasket's seam is inserted into the straight bottom section of the groove. Inserting it into a corner may lead to eventual tearing.

35010372 9/2007 199

Periodic Check Points

Operation Environment

The operating temperature should be within the allowable range (0 °C to 50 °C) (32 °F to 122 °F).

The operating humidity should be within the specified range (10 %RH to 90 %RH), dry bulb temperature of 39 °C (102 °F) or less.

The operating atmosphere should be free of corrosive gases.

Electrical Specifications

The input voltage should be within 19.2 to 28.8 VDC.

Related Items Are all power cords and cables connected properly? Have any become loose?

Are all mounting brackets holding the unit securely?

Are there many scratches or traces of dirt on the installation gasket?

200 35010372 9/2007

Replacing the Backlight

Introduction The following maintenance applies only to the XBT GT5000/6000/7000 series units.

There are no serviceable parts inside the XBT GT1000/2000/4000 and the XBT GK series.

The XBT GT5000/6000/7000 series units’ backlight can be replaced by the customer. Please see the Instruction Sheet that comes with replacement backlights for details on how to replace the backlight. Contact your local distributor for more information.

If the unit's backlight burns out and the unit is not set to standby mode, the panel remains active.

BACKLIGHT AREA IS HOT

Let the product cool down for 10 minutes before removing the backlight.

Wear gloves to touch the inner components.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

EXPOSED ELECTRICAL COMPONENTS

Remove power cords and disconnect all cables, including communication cables, before opening the product.

Do not open the product for any reason except backlight replacement.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

BACKLIGHT IS FRAGILE

Do not touch the glass directly.

Do not try to remove the power cord.

Failure to follow these instructions can result in injury or equipment damage.

WARNING

WARNING

CAUTION

35010372 9/2007 201

How to Determine if the Backlight is Burned Out

If your unit's backlight suddenly turns OFF, use the following steps to determine if the backlight is actually burned out:

If the unit's Backlight Control is not set and the screen has gone blank, your backlight is burned out.

If the unit's Backlight Control is set to standby mode, the screen has gone blank, and touching the screen or performing another input operation does not cause the display to reappear, your backlight is burned out.

SSI TECHNOLOGIES, INC.

P. O. Box 5011 3200 Palmer Drive Janesville, WI 53547-5011 Phone: (608)757-2000 Fax: (608)757-2009

SSI Technologies MediaSensor� Absolute & Gage Pressure Transducers

Product Overview

Product Description SSI�s line of bulk micro-machined, absolute & gage pressure transducers and transmitters for both harsh and benign media with the superior accuracy of <±0.5% represents a significant cost savings over currently available pressure transducers. These compact, robust sensors measure pressures from 15 Psi to 3,000 Psi and are well suited for a variety of automotive, industrial and commercial applications. SSI, a leading OEM supplier of automotive sensors � having delivered more than 100 million sensors to its customers, offers the MediaSensor�, targeted at industrial and commercial applications where cost, size, and performance are critical.

Typical Applications Refrigeration Fuel Cells Pumps Hydraulics Process Control Spraying Systems

Pneumatics Compressors Flow Robotics Agriculture Hydrogen Storage

Standard Full Scale Pressure Ranges

15, 50, 75, 100, 200 and 300 Psig

500, 750, 1000, 1500, 2000, and 3000 Psis

15, 50, 75, 100, 200, 300, 500, 750, 1000, 1500, 2000, and 3000 Psia

Improved Accuracy Lower Pressure Ranges M12 & Mini DIN Connectors

MediaSensor� with integrated signal conditioning

(shown with Packard Connector and Integral Harness)

Special Features Superb Accuracy - <±0.5% Robust Package - All laser-welded stainless steel design for optimal media isolation Maximum Flexibility - Custom ASIC provides signal conditioning for calibration and temperature compensation.

Standard and custom options available Compact size, excellent price/performance ratio 5 Volt input with 0.5 � 4.5 Volt output 8 - 30 Volt input with 4 � 20 mA & 1 � 5 Volt output

Call us at (888) 477-4320 or visit our Web Site: http://ssitechnologies.com

SSI TECHNOLOGIES, INC.

Corporate Headquarters 3200 Palmer Drive Janesville, WI 53547-5011 Phone: (608)757-2000 Fax: (608)757-9019

SSI Technologies Media Sensor� Absolute & Gage Pressure Transducers

Product Overview

Performance Specifications (all values at 22oC unless noted otherwise)

Output Type 0.5 to 4.5 Volts 4 � 20 mA 1 � 5 Volts

Accuracy1 < 0.50% FS < 0.50% FS < 0.50% FS Zero & Span Error < 0.25% FS < 0.25% FS < 0.25% FS Thermal Error (-40oC to 105oC) < 0.50% FS < 0.50% FS < 0.50% FS Total Error < 1.0% FS < 1.0% FS < 1.0% FS Stability (Typical) < 0.25% FS / Year < 0.25% FS / Year < 0.25% FS / Year Zero Pressure Offset 2 0.50 V 4.0 mA 1.0 V Full Scale Output3 4.5 V 20 mA 5.0 V Operating Temperature -40 to 105oC -40 to 105oC -40 to 105oC Storage Temperature -40 to 105oC -40 to 105oC -40 to 105oC Proof Pressure 3 X FS 3 X FS 3 X FS Burst Pressure Absolute Pressure Transducers

10 X FS or 15,000 Psia (whichever is less)

10 X FS or 15,000 Psia (whichever is less)

10 X FS or 15,000 Psia (whichever is less)

Burst Pressure Gage Pressure Transducers

3 X FS 3 X FS 3 X FS

Electrical Specifications

Output Type 0.5 to 4.5 Volts 4 � 20 mA 1 � 5 Volts

Supply Voltage 5 +/- 0.5 8 to 30 Volts 8 to 30 Volts Supply Current < 6 mA Not Applicable < 3 mA Output Current 0.45mA Max

(Sink or Source) Not Applicable 0.45mA Max

(Sink or Source)

Response Time < 1 ms < 1 ms < 1ms

Reliability and Environmental Performance

Test Conditions Value Units

Wetted Materials 304L & 316L Stainless Steel - - Pressure/Temperature Cycles4 0 to FS @ 8Hz; and �40oC to 105oC >1.8x106 Cycles Thermal Shock 105oC to �40oC, 0.5 hr soaks at Temp. (2s Transfer) 250 Cycles Vibration 10 to 2050 Hz, 20 Sinusoidal, 3 Axes 144 Hours EMC Compatibility5 10 Volts/meter per EN 61000-4-3 Humidity 85oC and 90% to 95% R. H. 250 Hours Weight Model 41 with M12 x 1.5 6g 304L Stainless Port 85 Grams 1Includes hysteresis, repeatability, & non-linearity (BFSL) 4Pressure cycling performed at rated full scale pressure.

2Transducer output @ 0 Psia, 0 Psig, or 0 Psis(consult factory for other options)

5Higher levels of EMC Compatibility are available upon request.

3Transducer output @ Pressure Range + 14.5 Psia

Watertronics Pressure Transducer P/N 69-20-1740

Transducer label

SUMMITVILLE DAM IMPOUNDMENT DRAFT PUMP STATION STANDARD OPERATING PROCEDURES

DAMID: 210103

APPENDIX B

ELECTRICAL EQUIPMENT OPERATION AND MAINTENANCE MANUAL

ONE HUNDRED YEARS IN BUSINESS

12150 East 112th Avenue, Henderson, CO 80640 p 303.286.8000 f 303.286.1811 www.sturgeonelectric.com

Summitville MineSummitville Mine

Water Treatment Plant

Magnetic Flow Meter - November 2012

8119 Shaffer Parkway, Unit C Browns Hill Engineering and Controls

PROVIDED BY:

Magnetic Flow Meter November 2012

Project Manager: Lino A Alvarez Job Id: 10-164

8119 Shaffer Parkway, Unit C

Operations & Maintenance Manual

Littleton, Colorado 80127 720.344.7771

Flow Flow Duration V target V meas. o.r.* Outp.** [%] [l/s] [s] [mA] Tolerance limit: ±0.5% o.r.* ± Zero stability

40.2 10.1 30.1 10.42

100.5 25.3 30.1 20.07

*o.r.: of rate

**Calculated value (4 - 20 mA)

Flow

100%)

20925075-2854010

1000202150 FCP-7.1.2

Calibration rig

25.1327 l/s

-0.06

[l]

-0.02

Purchase order number

Service interface

Water temperatureTag Nº

Order code

Order Nº/Manufacturer

Transmitter/Sensor

Serial Nº

US-3004885701-10 / Endress+Hauser Flowtec AG

50W80-HRGA1AK5BAAA

19.09.2012

-1

-1.5

Measured error % o.r.

Calibrated full scale

Calibrated output

79.5 °F Zero point

50 60

Page 1 / 1

1.0153 Calibration factor

F-68700 Cernay / CH-4153 Reinach

Rue de l'Europe 35 / Kägenstrasse 7

Date of calibration

Endress+Hauser Flowtec AG

Endress+Hauser Flowtec operates ISO/IEC 17025 accredited calibration facilities in Reinach (CH), Cernay (FR), Greenwood (USA), Traceability to the national standard for all test instruments used for the calibration is guaranteed.

à Aurangabad (IN) and Suzhou (CN).

PROMAG 50 W 3"

[l]

F8197919000

760.048

303.615 303.567

759.565

303.613 0.02 10.4340.2 10.1 30.1 303.556

100 [%]

0.5

30 80

1.5

- - - - - -0.5

J. Breda Operator

Certified acc. to

ISO 9001

For detailed data concerning output specifications of the unit under test, see Technical Information (TI), chapter Performance characteristics.

20 9040